Thermodynamic simulation models for predicting Al2O3-MgO castable chemical corrosion

The chemical corrosion of two Al₂O₃-MgO castables (containing distinct binder sources: hydratable alumina or calcium aluminate cement) were evaluated in this work via thermodynamic calculations. Two simulation models were proposed according to the following procedures: (1) firstly the matrix and later the aggregates of the castables were placed, separately, in contact with an industrial basic slag, and (2) the overall chemical composition of the design castables was directly reacted with the molten slag. The theoretical results were further compared with experimental data collected after corrosion cup tests. Although the thermodynamic evaluation of the overall castable compositions was able to identify the phase transformations correctly, a two-step analysis of the matrix components and aggregates particles seems to be the best alternative to evaluate the binder source effect on the corrosion performance of the two Al₂O₃-MgO refractory materials.     

Thermodynamic evaluation of spinel containing refractory castables corrosion by secondary metallurgy slag

This work addresses the thermodynamic evaluation of different spinel-containing refractory castable compositions in contact with a basic steel ladle slag (CaO/SiO₂ ∼ 9). The main differences among the castable compositions were the amount of silica fume (0 or 1 wt%), the binder source (calcium aluminate cement or hydratable alumina) and the spinel incorporation route (in situ or pre-formed). The interaction of the liquid slag with the refractory was carried out with the help of thermodynamic software (FactSage) and the applied methodology considered the changes in the slag composition due to the interaction with the castable. The theoretical results were compared with the experimental data attained by corrosion cup-tests, pointing out that the thermodynamic calculations were suitable for predicting various aspects observed in the corroded samples by SEM. Therefore, the equilibrium simulations led to parameters that indicated the corrosion resistance trends, complementing the experimental evaluation and reducing further experimental testing.     

Calcium aluminate cement source evaluation for Al2O3-MgO refractory castables

Alumina-magnesia refractory castables are commonly bonded with calcium aluminate cements. At temperatures above 1200 °C, these materials present an expansive behavior due to the in situ spinel (MgAl₂O₄) formation and the CA₂ and CA₆ ones. One alternative to control the volumetric stability is by replacing the typical cements used (30 wt.% CaO) for another containing less lime (20 wt.% CaO). Nevertheless, when changing the cement sources, the castable's properties would be affected. Among them, the most relevant are the green mechanical strength, the drying behavior, the properties at intermediate and high temperatures, the expansion behavior, the hot modulus of rupture and creep. Considering these aspects, the objective of this work was to evaluate the impact of different cement sources in the processing steps and properties of alumina-magnesia castables. The results pointed out specific behaviors for each cement source during the whole processing stages, highlighting the importance of its proper selection in order to attain the required properties in working conditions.     

Hot elastic modulus of Al2O3–SiC–SiO2–C castables

This work discusses an investigation of the hot elastic modulus and crack generation of two Al₂O₃–SiC–SiO₂–C castable compositions throughout two thermal cycles in an oxidizing atmosphere. A high temperature ultrasonic technique carried out using a long bar mode, thermogravimetric, X-ray diffraction, apparent porosity analyses and thermodynamic calculations were evaluated in order to understand the results. Significant changes in the castables’ elastic modulus values were observed with temperature, which were related to the decomposition of hydrated phases, antioxidant reactions, changes in the liquid phase viscosity, and formation and closure of microcracks in the castable microstructure. The results attained are fundamental for providing data for thermo-mechanical computing simulations by finite element analyses and for the design of large refractory structures, such as blast furnace runners for the steel industry.     

Slag attack evaluation of in situ spinel-containing refractory castables via experimental tests and thermodynamic simulations

Although the in situ spinel formation in alumina-magnesia refractory castables induces an expansive behavior, many investigations highlight its positive role in the corrosion resistance of such materials. Thus, this work addresses the slag attack evaluation of four designed in situ spinel-containing castables (containing hydratable alumina or calcium aluminate cement as a binder source and 0 or 1 wt% of silica fume) when in contact with a Fe_xO rich industrial slag. Corrosion cup-tests, microstructural characterization and a two-step thermodynamic simulation model were used in order to investigate the reactions taking place during the slag-refractory interactions. According to the attained results, hydratable alumina seems to be a suitable binder to improve the corrosion resistance of such castables, as it induces densification and the formation of an alumina-rich spinel phase at the slag-matrix interface. Moreover, the thermodynamic calculations matched to the experimental observations, attesting the efficiency of the proposed simulation model for the evaluation of the in situ spinel-containing castable corrosion behavior.     

High-temperature mechanical behavior of Al2O3/graphite composites

Uniaxial compressive creep behaviour of spark-plasma-sintered Al₂O₃/graphite particulate composites has been studied at temperature between 1250 and 1350 °C. Values of stress exponent, n, ranging from 1 to 1.4 and, activation energy, Q, of 600 ± 40 kJ/mol have been determined. With 10 vol% graphite in the composite, the creep deformation of the composite is controlled by the fine-grained Al₂O₃ matrix, where Coble creep has been identified as the dominant creep mechanism.     

Creep behavior and related structural defects in Al2O3-Ln2O3 (ZrO2) directionally solidified eutectics (Ln = Gd, Er, Y)

The eutectic architecture of “in situ” composites prepared by solidification from the melt in the Al₂O₃-Ln₂O₃ (ZrO₂) systems gives rise to materials with a high creep resistance. With the objective to elucidate the high temperature deformation micro-mechanisms, microstructural features are investigated on crept specimens. Compressive creep experiments have been carried out between 1400 and 1550 °C for various eutectic compositions. Different deformation regimes depending on considered systems and conditions of stress and temperature are revealed. Transmission electron microscopy studies emphasize the activation of different slip systems in the alumina phase and the deformation by dislocation climb processes controlled by bulk diffusion.     

Al2O3-MgO refractory castables with enhanced explosion resistance due to in situ formation of phases with lamellar structure

This work evaluated an alternative route (formic acid addition and in situ generation of hydrotalcite phases) to reduce the explosion trend of dense MgO-bonded refractory castables during their drying step. Aqueous suspensions containing different magnesia sources (caustic or dead-burnt) and hydratable alumina were firstly analyzed in order to identify the likelihood of generating these in situ compounds with a lamellar structure in mixtures prepared with and without formic acid (hydrating agent). After that, high-alumina vibratable castables containing MgO and this carboxylic acid were evaluated and the following experimental tests were carried out: thermogravimetry, mechanical strength evaluation, apparent porosity and hot elastic modulus measurements. According to the obtained results, the thermal decomposition of the formed hydrotalcite-like phases led to samples’ mass loss over a broader temperature range, preventing their explosion even when a critical heating rate (20?°C?min^?1) was applied during the tests. Besides that, no deleterious effect to the refractories’ mechanical properties were observed during firing (i.e. softening at high temperatures). Thus, the addition of formic acid and the in situ formation of hydrotalcite-like phases is suggested as an alternative route to the conventional incorporation of amorphous silica or polymeric fibers into the castable dry-mixes to prevent the explosion of MgO-bonded refractories.     

Damage resistance and R-curve behavior of multilayer Al2O3/SiC ceramics

Damage resistance and R-curve behavior of multilayer Al₂O₃/SiC ceramics were evaluated in bending by the indentation-strength and the single-edge-notched-beam methods. Due to the crack deflection at the Al₂O₃/SiC interfaces, a plateau indentation strength response was achieved, suggesting an exceptional resistance to contact-induced damage. Moreover, fracture toughness was observed to increase from 8.0 to 15.5 MPa m^1/2 with increasing notch depth from 0.5 to 2.0 mm, indicative of a strong R-curve behavior.     

Microstructure and phase evolution of alumina-spinel self-flowing refractory castables containing nano-alumina particles

The microstructure and phase composition of alumina-spinel self-flowing refractory castables added with nano-alumina particles at different temperatures are investigated. The physical and mechanical properties of these refractory castables are studied. The results show that the addition of nano-alumina has a great effect on the physical and mechanical properties of these refractory castables. With the increase of nano-alumina content in the castable composition, the mechanical strength is considerably increased at various temperatures. It is shown that nano-alumina particles can affect formed phases after firing. The platy crystals of CA₆ are detected inside the grain boundaries of tabular alumina and spinel grains in samples fired at 1500 °C. CA₆ phase can be formed at lower temperatures (1300 °C) with the addition of nano-alumina particles. As a result of using nanometer-sized alumina particles with high surface area, the solid phase sintering of the nano-sized particles and CA₆ formation can occur at lower temperatures.     

Corrosion mechanisms of Al2O3/MgAl2O4 by V2O5, NiO, Fe2O3 and vanadium slag

The effects of V₂O₅, NiO, Fe₂O₃ and vanadium slag on the corrosion of Al₂O₃ and MgAl₂O₄ have been investigated. The specimens of Al₂O₃ and MgAl₂O₄ with the respective oxides above mentioned were heated at 10 °C/min from room temperature up to three different temperatures: 1400, 1450 and 1500 °C. The corrosion mechanisms of each system were followed by XRD and SEM analyses. The results obtained showed that Al₂O₃ was less affected by the studied oxides than MgAl₂O₄. Alumina was only attacked by NiO forming NiAl₂O₄ spinel, while the MgAl₂O₄ spinel was attacked by V₂O₅ forming MgV₂O₆. It was also observed that Fe₂O₃ and Mg, Ni, V and Fe present in the vanadium slag diffused into Al₂O₃. On the other hand, the Fe₂O₃ and Ca, S, Si, Na, Mg, V and Fe diffused into the MgAl₂O₄ structure. Finally, the results obtained were compared with those predicted by the FactSage software.     

Effect of surface-modified Al2O3 on the thermomechanical properties of polybutylene succinate/Al2O3 composites

This study investigates the effect of the incorporation of alumina particles on the thermomechanical properties of polybutylene succinate (PBS)/Al₂O₃ composites. The alumina surface was modified with the carboxylic groups of maleic acid through simple acid-base and in situ polymerization reactions. Scanning electron microscope (SEM) results revealed the introduction of maleic acid treated alumina significantly affect the morphology of the PBS/Al₂O₃ composites as compared to the neat PBS. The thermal conductivity of the composite (0.411?W?m^?1 K^?1) was more than twice that of neat PBS. The composite containing polymerization-modified alumina showed a 50% increase in storage modulus compared with that of neat PBS. In addition, universal testing machine (UTM) and differential scanning calorimetry (DSC) measurements indicated an increase in the tensile strength and degree of crystallinity after the incorporation of modified alumina in the PBS/Al₂O₃ composite.     

Effect of CeO2 addition on densification and microstructure of Al2O3-YSZ composites

Alumina (Al₂O₃) and alumina-yttria stabilized zirconia (YSZ) composites containing 3 and 5 mass% ceria (CeO₂) were prepared by spark plasma sintering (SPS) at temperatures of 1350-1400 °C for 300 s under a pressure of 40 MPa. Densification, microstructure and mechanical properties of the Al₂O₃ based composites were investigated. Fully dense composites with a relative density of approximately 99% were obtained. The grain growth of alumina was inhibited significantly by the addition of 10 vol% zirconia, and formation of elongated CeAl₁₁O₁₈ grains was observed in the ceria containing composites sintered at 1400 °C. Al₂O₃-YSZ composites without CeO₂ had higher hardness than monolithic Al₂O₃ sintered body and the hardness of Al₂O₃-YSZ composites decreased from 20.3 GPa to 18.5 GPa when the content of ZrO₂ increased from 10 to 30 vol%. The fracture toughness of Al₂O₃ increased from 2.8 MPa m^1/2 to 5.6 MPa m^1/2 with the addition of 10 vol% YSZ, and further addition resulted in higher fracture toughness values. The highest value of fracture toughness, 6.2 MPa m^1/2, was achieved with the addition of 30 vol% YSZ.     

Coarse-grained refractory composites based on Nb-Al2O3 and Ta-Al2O3 castables

Coarse-grained refractory composites, with grain sizes between 20 and 5000?µm, based on Nb-Al₂O₃ and Ta-Al₂O₃ castables were produced for the first time and characterised in terms of shrinkage after sintering, splitting tensile strength, compressive strength, porosity and the measurement of the elastic properties (E, G and $\nu$). After sintering at a temperature of 1600?°C, the shrinkage of the composites was 1.5% and 0.3%. Measured values of splitting tensile strength were between 5.5 and 15?MPa and the ones of compressive strength were between 23 and 89?MPa. Values of E and G were between 117 and 45?GPa and 48–17?GPa, respectively, for samples with 11–45?vol% refractory metal. Poisson's ratio was found to be very sensitive to the bonding between the fine matrix and coarse-grained particles of the composites. Its value increased from 0.25 for good bonding to $\nu =0.43$ in case of poor bonding between the coarse metal particles and the fine ceramic matrix. DTA/TG measurement under air atmosphere showed that the metal-ceramic composites start to oxidise at temperatures above 450?°C.     

Phase diagram of the Al2O3-HfO2-Y2O3 system

The phase diagram of the Al₂O₃-HfO₂-Y₂O₃ system was first constructed in the temperature range 1200-2800 °C. The phase transformations in the system are completed in eutectic reactions. No ternary compounds or regions of appreciable solid solution were found in the components or binaries in this system. Four new ternary and three new quasibinary eutectics were found. The minimum melting temperature is 1755 °C and it corresponds to the ternary eutectic Al₂O₃ + HfO₂ + Y₃Al₅O₁₂. The solidus surface projection, the schematic of the alloy crystallization path and the vertical sections present the complete phase diagram of the Al₂O₃-HfO₂-Y₂O₃ system.     

Effect of Al2O3 on mechanical properties of Ti3SiC2/Al2O3 composite

The effect of Al₂O₃ on mechanical properties of Ti₃SiC₂/Al₂O₃ composite fabricated by SPS was studied systematically. The results show that the hardness of the Ti₃SiC₂/Al₂O₃ composite can reach 10.28 GPa, 50% higher than that of pure Ti₃SiC₂. However, slight decrease in the other mechanical properties was observed with Al₂O₃ addition higher than 5–10 vol.%, which is believed to be due to the agglomeration of Al₂O₃ in the composite.     

Tribological properties of Al2O3 nanoparticles as lubricating oil additives

Nano-scale Al₂O₃ spherical particles, prepared via a hydrothermal method and modified by silane coupling agent, can be well-dispersed in lubricating oil. The tribology properties of Al₂O₃ nanoparticles as lubricating oil additives have been studied by four-ball and thrust-ring friction test, which illustrate that the modified Al₂O₃ nanoparticles can effectively improve the lubricating behaviors compared to the base oil. When the added concentration is 0.1 wt%, the friction coefficient and the wear scar diameter are both smallest. The lubrication mechanism is that a self-laminating protective film is formed on the friction surface and the wear behavior changes from sliding friction to rolling friction.     

Infiltration of Al2O3/Y2O3 mix into SiC ceramic preforms

Silicon carbide ceramics are very interesting materials to engineering applications because of their properties. These ceramics are produced by liquid phase sintering (LPS), where elevated temperature and time are necessary, and generally form volatile products that promote defects and damage their mechanical properties. In this work was studied the infiltration process to produce SiC ceramics, using shorter time and temperature than LPS, thereby reducing the undesirable chemical reactions. SiC powder was pressed at 300 MPa and pre-sintered at 1550 °C for 30 min. Unidirectional and spontaneous infiltration of this preform by Al₂O₃/Y₂O₃ liquid was done at 1850 °C for 5, 10, 30 and 60 min. The kinetics of infiltration was studied, and the infiltration equilibrium happened when the liquid infiltrated 12 mm into perform. The microstructures show grains of the SiC surrounded by infiltrated additives. The hardness and fracture toughness are similar to conventional SiC ceramics obtained by LPS.     

Relationship between fracture toughness characteristics and morphology of sintered Al2O3 ceramics

The influence of sintering temperature and soaking time on fracture toughness of Al₂O₃ ceramics has been investigated. The samples were prepared by solid state sintering at 1500, 1600 and 1700 °C for different soaking time periods. The fracture toughness of the sintered samples was determined by inducing cracks using Vickers indentation technique. Microstructural investigations on fracture surfaces obtained by three point bend test mode were made and correlated with fracture toughness. Crack deflection in the samples sintered at 1500 and 1600 °C for which ranges of fracture toughness are 5.2–5.4 and 5.0–5.6 MPa m^1/2 respectively, are found. The samples sintered at 1700 °C have lower fracture toughness ranging between 4.6 and 5.0 MPa m^1/2. These samples have larger grains and transgranular fracture mode is predominant. The crack deflection has further been revealed by SEM and AFM observations on fracture surface and fracture surface roughness respectively.     

Sintering of Al2O3-SiC composite from sol-gel method with MgO, TiO2 and Y2O3 addition

Al₂O₃-SiC composite ceramics were prepared by pressureless sintering with and without the addition of MgO, TiO₂ and Y₂O₃ as sintering aids. The effects of these compositional variables on final density and hardness were investigated. In the present article at first α-Al₂O₃ and β-SiC nano powders have been synthesized by sol-gel method separately by using AlCl₃, TEOS and saccharose as precursors. Pressureless sintering was carried out in nitrogen atmosphere at 1600 °C and 1630 °C. The addition of 5 vol.% SiC to Al₂O₃ hindered densification. In contrast, the addition of nano MgO and nano TiO₂ to Al₂O₃-5 vol.% SiC composites improved densification but Y₂O₃ did not have positive effect on sintering. Maximum density (97%) was achieved at 1630 °C. Vickers hardness was 17.7 GPa after sintering at 1630 °C. SEM revealed that the SiC particles were well distributed throughout the composite microstructures. The precursors and the resultant powders were characterized by XRD, STA and SEM.