Improvements on corrosion behaviours of MgO-spinel composite refractories by addition of ZrSiO4

Corrosion behaviours of MgO-spinel-ZrSiO₄ compositions were investigated. The influence of corrosion resistance based on the microstructural changes occurred due to the solubilities of constituents in corroded regions was examined using SEM/EDX analysis. The following observations were determined by microstructural characterisation performed at the interface of clinker-refractory: (i) the formation of ZrO₂ and Mg₂SiO₄ phases among MgO grains after sintering, (ii) the formation of CaZrO₃ phase during penetration, (iii) prevention of penetration by new phases formed making a barrier effect against clinker with an improvement in densification, and (iv) the decrease in the amount of CaO and the increase in the quantity of MgO using EDX analysis made moving from clinker towards refractory. The addition of ZrSiO₄ reduced the values of penetration and spreading areas of the corroded regions of composite refractories and improved the corrosion resistance significantly, leading to a long service life of MgO-spinel-zircon based refractories for industrial applications.     

Developments on the mechanical properties of MgO-MgAl2O4 composite refractories by ZrSiO4-3 mol% Y2O3 addition

Improvements and the effects of additions of ZrSiO₄-3 mol% Y₂O₃ into MgO-MgAl₂O₄ composite refractories on mechanical properties and thermal stress resistance parameters were investigated. Significant improvements were achieved on mechanical properties and R-R_st parameters up to ∼2 and ∼3-fold ratios. The major parameters improving mechanical properties and thermal behaviour of refractories were determined as follows: (i) the increase in resistance to crack initiation and propagation due to formation of Mg₂SiO₄ phase after decomposition of zircon; (ii) propagation of the microcracks formed in the structure for a short distance by interlinking each other; (iii) arresting or deviation of microcracks when reaching pores or ZrO₂ grains released after dissociation of zircon, located together with Y₂O₃ particles, and furthermore; (iv) co-presence of both intergranular and transgranular types of cracks, and with incorporation of zircon-Y₂O₃; (v) increase in density; and (vi) a significant reduction in MgO grain size.     

Structure characterization and mechanical properties of CeO2–ZrO2 solid solution system

The measured and calculated lattice parameters, microstructures, and mechanical properties (fracture toughness and microhardness) of CeO₂–ZrO₂ system ceramics are investigated, using CeO₂–ZrO₂ solid solution powder prepared by a microwave-induced combustion process. The CeO₂–ZrO₂ solid solution ceramics were sintered at 1500 °C for 6 h in air; the density of all specimens was greater than 94% of the theoretical density. For Ce_1−xZr_xO₂ (0.00  x  0.50), the measured lattice parameter is in accordance with that of Kim's doped CeO₂ model_. On the other hand, for x  0.50, the measured values fit Kim's doped ZrO₂ model. The fracture toughness and microhardness of CeO₂–ZrO₂ system ceramics with various compositions were investigated with Vickers indentation. The results showed that the crack mode of CeO₂–ZrO₂ solid solution was Palmqvist cracks under loads of 1 kg. Generally, the fracture toughness should increase with grain size at the submicron scale. However, larger grains may lead to spontaneous transformation, which should decrease the potential toughening at room temperature. This behavior was observed in the Ce_0.25Zr_0.75O₂ ceramic, which demonstrated a high fracture toughness that may be ascribed to two causes: (1) fine grain size and (2) transformation toughening.     

Structural, thermal and mechanical properties of transparent Yb:(Y0.97Zr0.03)2O3 ceramic

Yb doped (Y_0.97Zr_0.03)₂O₃ transparent ceramics were fabricated by solid state reaction and vacuum sintering. The microstructure, thermal and mechanical properties of Y₂O₃ ceramic, as well as the effect of Yb doping concentration on these properties were investigated in detail. The lattice parameter and unit cell volume decrease with the increasing of Yb content, whereas thermal expansive coefficient increases. With Yb content increasing from 0 to 8 at.%, the mean grain size increases from 15.82 μm to 26.54 μm, and the thermal conductivity at room temperature (RT) decreases from 11.97 to 6.39 W/m/K. The microhardness decreases with Yb content, and the microhardness and fracture toughness of (Y_0.97Zr_0.03)₂O₃ transparent ceramic is 11.11 GPa and 1.29 MPa m^1/2, respectively.     

The comparison of mechanical behavior of MgO-MgAl2O4 with MgO-ZrO2 and MgO-MgAl2O4-ZrSiO4 composite refractories

Mechanical properties of different compositions obtained from the additions of 5, 10, 20 and 30 wt.% zircon (ZrSiO₄) into the MgO-spinel composite refractories and ZrO₂ into MgO have been examined, the variations that occurred have been determined, and the parameters affecting those factors have been investigated with the reasons. The density, strength, Young's modulus, fracture toughness, fracture surface energy and work of fracture were measured and evaluated. Microstructural variations and fracture surfaces have been examined and the formation of new phases has been identified depending on the additive type and quantity. The relationships between mechanical properties and structural variations for different compositions have been examined. In MgO-spinel materials, strength, Young's modulus and fracture toughness values decrease up to 20% spinel addition and stay almost constant for further loads. ZrO₂ addition displays same trend but not as effective as spinel. Besides, since ZrO₂ is stable in cubic form, it does not show any toughening mechanism. Forsterite formation is the most important factor for 2-fold improvement in the mechanical properties of MgO-spinel-zircon refractories. The more the zircon addition, the more the mechanical properties improve. The generation of natural bonding between matrix particles with forsterite formation, on the other hand, causes the fracture path to turn to transgranular fracture with an increase in fracture surface energy and a decrease in work of fracture, among which the latter is considered as an indicator of thermal shock resistance of the materials being high.     

Thermal shock resistance and mechanical properties of La2Ce2O7 thermal barrier coatings with segmented structure

La₂Ce₂O₇ (LCO) is a promising candidate material for thermal barrier coatings (TBCs) application because of its higher temperature capability and better thermal insulation property relative to yttria stabilized zirconia (YSZ). In this work, La₂Ce₂O₇ TBC with segmentation crack structure was produced by atmospheric plasma spray (APS). The mechanical properties of the sprayed coatings at room temperature including microhardness, Young's modulus, fracture toughness and tensile strength were evaluated. The Young's modulus and microhardness of the segmented coating were measured to be about 25 and 5 GPa, relatively higher than those of the non-segmented coating, respectively. The fracture toughness of the LCO coating is in a range of 1.3–1.5 MPa m^1/2, about 40% lower than that of the YSZ coating. The segmented TBC had a lifetime of more than 700 cycles, improving the lifetime by nearly two times as compared to the non-segmented TBC. The failure of the segmented coating occurred by chipping spallation and delamination cracking within the coating.     

Thermal conductivity in mullite/ZrO2 composite coatings

Mullite-based multilayered structures have been suggested as promising environmental barrier coatings for Si₃N₄ and SiC ceramics. Mullite has been used as bottom layer because its thermal expansion coefficient closely matches those of the Si-based substrates, whereas Y–ZrO₂ has been tried as top layer due to its stability in combustion environments. In addition, mullite/ZrO₂ compositions may work as middle layers to reduce the thermal expansion coefficient mismatch between the ZrO₂ and mullite layers. Present work studies the thermal behaviour of a flame sprayed mullite/ZrO₂ (75/25, v/v) composite coating. The changes in crystallinity, microstructure and thermal conductivity of free-standing coatings heat treated at two different temperatures (1000 and 1300 °C) are comparatively discussed. The as-sprayed and 1000 °C treated coatings showed an almost constant thermal conductivity (K) of 1.5 W m⁻¹ K⁻¹. The K of the 1300 °C treated specimen increased up to twice due to the extensive mullite crystallization without any cracking.     

Preparation of ZrO2/Gd2O3 composite ceramic materials by coprecipitation method

High burnup is a goal for further development of advanced nuclear power in the future. However, along with the increase of burnup, it becomes more diffidult to control reactor reactivity, which affects the operation safety of the nuclear reactor. Al₂O₃/B₄C burnable poison materials widely used in pressurized water reactor currently will not meet the requirements of burnable poison materials in high burnup nuclear power. Because of the better performance of ZrO₂/Gd₂O₃ burnable poison materials than that of Al₂O₃/B₄C, this paper studies the preparation of ZrO₂/Gd₂O₃ composite ceramic materials by the coprecipitation method. The experimental results show that at the sintering temperature of 1500–1650 °C, ZrO₂/Gd₂O₃ composite ceramic grains are small, compact and uniform with the generation of homogeneous solid solution. At 1600 °C, ZrO₂–10%Gd₂O₃ has the highest density and mechanical strength.     

Corrosion mechanisms of Al2O3/MgAl2O4 by V2O5, NiO, Fe2O3 and vanadium slag

The effects of V₂O₅, NiO, Fe₂O₃ and vanadium slag on the corrosion of Al₂O₃ and MgAl₂O₄ have been investigated. The specimens of Al₂O₃ and MgAl₂O₄ with the respective oxides above mentioned were heated at 10 °C/min from room temperature up to three different temperatures: 1400, 1450 and 1500 °C. The corrosion mechanisms of each system were followed by XRD and SEM analyses. The results obtained showed that Al₂O₃ was less affected by the studied oxides than MgAl₂O₄. Alumina was only attacked by NiO forming NiAl₂O₄ spinel, while the MgAl₂O₄ spinel was attacked by V₂O₅ forming MgV₂O₆. It was also observed that Fe₂O₃ and Mg, Ni, V and Fe present in the vanadium slag diffused into Al₂O₃. On the other hand, the Fe₂O₃ and Ca, S, Si, Na, Mg, V and Fe diffused into the MgAl₂O₄ structure. Finally, the results obtained were compared with those predicted by the FactSage software.     

Microstructure, mechanical properties and thermal shock resistance of plasma sprayed nanostructured zirconia coatings

Nanostructured yttria stabilized zirconia (YSZ) coatings were deposited by Atmospheric Plasma Spraying (APS). X-ray diffraction (XRD) was used to investigate their phase composition, while scanning electron microscopy (SEM) was employed to examine their microstructure. The coatings showed a unique and complex microstructure composed of well-melted splats with columnar crystal structure, partially melted areas, which resembled the morphology of the powder feedstock, and equiaxed grains. Vickers microhardness of nanostructured zirconia coatings was similar to that of the conventional ones and strongly depended on the indentation load. Otherwise, a higher thermal shock resistance was found. This effect was addressed to the retention of nanostructured areas in coating microstructure and to the corresponding high porosity.     

Mechanical properties and thermal shock resistance of Si2BC3N ceramics with ternary Al4SiC4 additive

Dense Si₂BC₃N ceramics were prepared through SPS sintering the amorphous Si₂BC₃N and Al₄SiC₄ powders obtained from mechanical alloying. The phase compositions, microstructures, and mechanical properties, as well as the thermal shock resistance were investigated. In addition, evaluations of oxidation and the ablation resistance were also preceded. The results show that Al₄SiC₄ phase can be detected at 1200 and 1400?°C under pressureless sintering. However, Al₄SiC₄ can be decomposed to AlN and SiC phases under higher temperatures. As for the bulk Si₂BC₃N ceramics, the Al₄SiC₄ additive induce the development of turbostratic BN(C) plates and improve the relative density consequently. Besides, the Al₄SiC₄ plates are embedded in the matrix of ceramics. Therefore, the mechanical properties and thermal shock resistance are improved apparently with the addition of additive. Meanwhile, the additive containing composites have superior ablation resistance than the pristine Si₂BC₃N ceramics due to their higher relative density.     

Synthesis and thermal behavior of Cu/Y2W3O12 composite

Cu metal matrix composite with Y₂W₃O₁₂ as a thermal expansion compensator was fabricated by high energy ball milling followed by compaction and sintering, and its thermal properties were explored for the potential applications as heat sinks in electronic industries, high precision optics, and space structures. The volume fraction of reinforcement was varied from 40% to 70% in order to tailor the composite for the simultaneous accomplishment of low thermal expansion and high thermal conductivity. The synthesis technique was optimized by varying the parameters like milling time from 1 to 20 h and sintering temperature from 600 to 1000 °C in order to achieve densified composites. The relative density of the composites is found to be around 90% for the 10 h milled powders followed by compaction at a pressure of 700 MPa and sintering at a temperature of 1000 °C. The thermal expansion of the composites exhibits linear behavior in the temperature range 200 to 800 °C and the low coefficient of thermal expansion (CTE) is found to be for Cu–70%Y₂W₃O₁₂ composite whose value, 4.32±0.75×10⁻⁶/°C, matches with that of Si substrate. The thermal conductivities are found to increase with a decrease in the volume fraction of the reinforcement and decrease with an increase in the temperature for all the samples. The experimentally determined CTE and thermal conductivity values are found to be comparable to those predicted by the thermal expansion based Kerner and Turner model and the thermal conductivity based Maxwell model, respectively.     

Effect of Al2O3 addition on bioactivity,thermal and mechanical properties of some bioactive glasses

Three bio-phosphate glass-specimens with and without Al₂O₃ addition were prepared in order to shed light on their bioactivity behavior towards the simulated body fluid biological solution (SBF). The results revealed that Al₂O₃ has significant effect on the ability of bio-glass to form the hydroxycarbonate apatite layer on its surface. That layer was detected by FTIR spectra, SEM micrographs and EDAX pattern. Also, the effect of Al₂O₃ on the mechanical properties was studied by measuring the hardness of the glass samples, which increased by Al₂O₃ addition. The thermal expansion coefficient was decreased by increasing the Al₂O₃ percent in the bio-glass samples.     

Structural and optical properties of Tm:Y2O3 transparent ceramic with La2O3, ZrO2 as composite sintering aid

The paper reports the use of La₂O₃ and ZrO₂ co-doping as a composite sintering aid for the fabrication of Tm:Y₂O₃ transparent ceramics. Two groups of experiments were conducted for investigating the influences of composite sintering aids on the microstructures and the optical properties of Tm:Y₂O₃ transparent ceramics in contrast to single La³⁺ and single Zr⁴⁺ doped Tm:Y₂O₃. Samples with composite sintering aids could realize fine microstructures and good optical properties at relatively low sintering temperatures. Grain sizes around 10 μm and transmittances close to theoretical value at wavelength of 2 μm were achieved for the 9 at.% La³⁺, 3 at.% Zr⁴⁺ co-doped samples sintered at 1500-1600 °C. The influences of the composite sintering aids on the emission intensities and the phonon energies of Tm:Y₂O₃ ceramics were also investigated.     

Effect of Al2O3 particle size on preparation and properties of ZTA ceramics formed by gelcasting

Zirconia-toughened alumina (ZTA) ceramics were prepared using three different kinds of Al₂O₃ powders (marked PW-A average particle size: 7.53 μm, marked PW-B average particle size: 1.76 μm, marked PW-C average particle size: 0.61 μm) by gelcasting. Effect of Al₂O₃ particle size on zeta potential, dispersant dosage and solid volume fractions of ZTA suspensions as well as the mechanical properties of ZTA green bodies and ceramics were investigated. The optimum dosages of dispersant for ZTA suspensions prepared by PW-A, PW-B and PW-C are 0.4 wt%, 0.5 wt% and 0.7 wt%, respectively. The highest solid volume fractions of ZTA suspensions can reach 62 vol% (SP-A), 60 vol% (SP-B) and 52 vol% (SP-C), respectively. The green bodies show a bending strength as high as 20 MPa, which can meet the requirement of machining. The Al₂O₃ powder with fine particle size is beneficial to the improvement of mechanical properties. The ZTA ceramics prepared by PW-B Al₂O₃ powder show the highest bending strength (680 MPa) and toughness (7.49 MPa m^1/2).     

Improvement of coke resistance of Ni/Al2O3 catalyst in CH4/CO2 reforming by ZrO2 addition

This work investigates the improvement of Ni/Al₂O₃ catalyst stability by ZrO₂ addition for H₂ gas production from CH₄/CO₂ reforming reactions. The initial effect of Ni addition was followed by the effect of increasing operating temperature to 500–700 °C as well as the effect of ZrO₂ loading and the promoted catalyst preparation methods by using a feed gas mixture at a CH₄:CO₂ ratio of 1:1.25. The experimental results showed that a high reaction temperature of 700 °C was favored by an endothermic dry reforming reaction. In this reaction the deactivation of Ni/Al₂O₃ was mainly due to coke deposition. This deactivation was evidently inhibited by ZrO₂, as it enhances dissociation of CO₂ forming oxygen intermediates near the contact between ZrO₂ and nickel where the deposited coke is gasified afterwards. The texture of the catalyst or BET surface area was affected by the catalyst preparation method. The change of the catalyst texture resulted from the formation of ZrO₂–Al₂O₃ composite and the plugging of Al₂O₃ pore by ZrO₂. The 15% Ni/10% ZrO₂/Al₂O₃ co-impregnated catalyst showed a higher BET surface area and catalytic activity than the sequentially impregnated catalyst whereas coke inhibition capability of the promoted catalysts prepared by either method was comparable. Further study on long-term catalyst stability should be made.     

Preparation and heat-insulating property of the bio-inspired ZrO2 fibers based on the silk template

Natural silk fibers were used as the template to prepare biomorphic ZrO₂ fibers. Silk fibers were first immersed into a Zr(NO₃)₄ solution and then sintered in air at high temperatures to produce the final ZrO₂ fibers. Their microstructures, phases, synthesis process, infrared absorption spectra and thermal conductivity were analyzed. The results show that these synthesized fibers retained the morphologies of silk faithfully. These ZrO₂ fibers also obtained the ability of absorbing infrared from the silk, so that they possessed better heat-insulating property than the traditional ZrO₂ fibers.     

Effect of TiO2 on phase evolution and microstructure of MgAl2O4 spinel in different atmospheres

The effect of TiO₂ on the formation and microstructure of magnesium aluminate spinel (MgAl₂O₄) at 1600 °C in air and reducing conditions were investigated. Under reducing conditions, stoichiometric MgAl₂O₄ spinel shifted toward alumina-rich types owing to volatilization of MgO, resulting in an increase in the porosity of fired samples. Addition of graphite to mixtures of MgO and Al₂O₃ intensified the reducing conditions and accelerated the formation of non-stoichiometric MgAl₂O₄. For TiO₂-containing samples on addition of MgAl₂O₄, magnesium aluminum titanium oxide (Mg_xAl_2(1−x)Ti_(1+x)O₅, x = 0.2 or 0.3) was detected as a minor phase. Under reducing conditions, XRD peak shifts were smaller for TiO₂-containing samples than for samples without TiO₂ owing to the formation of a solid solution of TiO₂ in MgAl₂O₄ and establishment of alumina-rich spinel, which have opposite effects on increasing the lattice parameter. In bauxite-containing samples, MgAl₂O₄ spinel, corundum, magnesium orthotitanate spinel (Mg₂TiO₄) and amorphous phases were identified. Mg₂TiO₄ spinel formed a complete solid solution with MgAl₂O₄ spinel but Mg₂TiO₄ remained as a distinct phase owing to the heterogeneous microstructure of bauxite-containing samples. Also dense microstructure established in air fired TiO₂ containing samples. The results are discussed with emphasis on the application and design of alumina-magnesia-carbon refractory materials, which are used in the steel industry.     

Study of the stability of the molten zone and the stresses induced during the growth of Al2O3-Y3Al5O12 eutectic composite by the laser floating zone technique

A series of analytical calculations is used to study both the effect of the thermal gradients and the stability of the molten zone in the laser floating zone growth of Al₂O₃-Y₃Al₅O₁₂ eutectic composite. The thermal gradients in the solidification interface have been calculated and the axial gradient compared with the experimental one of 4.5 × 10⁵ K/m. For these calculations the coefficients of heat transfer from the molten zone to the ambient at the solid-melt interface have been previously obtained. The thermal stresses generated by the high thermal gradients can induce crack formation during the cooling depending on the rod diameter. The theory predicts that it is possible to grow rods free of cracks up to R = 1.7 mm, at low rates (10 mm/h) in close agreement with the experimental critical radius of 1.6 mm.The dependence of the zone length on the input laser power used to carry out the growth is shown. The study of the floating zone profile allows determining the maximum stable zone length, verifying the stability criterion established by some authors.     

Highly porous ZrO2 ceramics fabricated by a camphene-based freeze-casting route: Microstructure and properties

A camphene-based freeze-casting method was adopted to create ceramics with aligned, equiaxed pores applied so far exclusively for ceramics—is demonstrated for ZrO₂ porous ceramics. The pore volume fraction, channel size and pore shape were controlled by varying the freezing temperature, solid content and sintering condition. After sublimation of camphene, the samples were sintered for 2 h at elevated temperatures ranging from 1400 to 1550 °C. The initial level of solid loading played a primary role in the resulting porosity of the product. The porosity decreased from 82.5 to 65.5 vol.% when the solid loading was increased from 10 to 20 vol.%. The relationship of the compressive strength versus initial solid loading and sintering temperature was discussed. This technique is considered potentially useful in fabricating novel porous ceramics with special structure, and introduces a new application field of freeze-casting.