Fabrication and characteristic of non-oxide fiber tow reinforced silicon nitride matrix composites by low temperature CVI process

Non-oxide fiber tow reinforced silicon nitride matrix composite was fabricated by low temperature CVI process with PyC as interphase. The tensile strength of the C and SiC fiber tow composites were 547 MPa and 740 MPa, respectively. The difference in tensile strength was analyzed based on the length, amount of pull-out fiber and also interface bonding. The infiltration uniformity of CVI silicon nitride (SiN) matrix within SiC fiber tow was comparable with that of CVI SiC matrix. These results suggested that the low temperature CVI process is suitable for the fabrication of fiber reinforced SiN matrix composites with proper interface bonding and high strength.     

Mechanical properties and electrical conductivity in a carbon nanotube reinforced silicon nitride composite

The influence of carbon nanotubes (CNTs) addition on basic mechanical, thermal and electrical properties of the multiwall carbon nanotube (MWCNT) reinforced silicon nitride composites has been investigated. Silicon nitride based composites with different amounts (1 or 3 wt%) of carbon nanotubes have been prepared by hot isostatic pressing. The fracture toughness was measured by indentation fracture and indentation strength methods and the thermal shock resistance by indentation method. The hardness values decreased from 16.2 to 10.1 GPa and the fracture toughness slightly decreased by CNTs addition from 6.3 to 5.9 MPa m^1/2. The addition of 1 wt% CNTs enhanced the thermal shock resistance of the composite, however by the increased CNTs addition to 3 wt% the thermal shock resistance decreased. The electrical conductivity was significantly improved by CNTs addition (2 S/m in 3% Si₃N₄/CNT nanocomposite).     

Preparation and mechanical properties of alumina composites reinforced with nickel-coated graphene

This paper discusses the influence of nickel–phosphorus coated graphene (Gn–Ni–P) and uncoated graphene (Gn) addition to an alumina matrix and its impact on the mechanical properties of obtained composites. The composites are prepared via powder processing and consolidated using the Spark Plasma Sintering (SPS) method. The effects of the addition of coated graphene and coating thickness on mechanical properties were evaluated. Physical properties such as relative density, hardness and fracture toughness were analyzed. Significant improvement of the fracture toughness (60%) for the composites with 2 vol% Gn–Ni–P compared to reference sample was observed. Moreover, 35% higher K_IC was noticed for Gn–Ni–P reinforced composites than for Al₂O₃–Gn.     

Effect of TiO2 addition on thermal and mechanical properties of Y-Si-Al-O-N glasses

Y-Si-Al-O-N glasses are intergranular phases in silicon nitride based ceramics in which the composition and volume fraction of oxynitride glass phases determine the sintering/shrinkage behaviour. Several investigations on oxynitride glass formation and properties have shown that addition of nitrogen increases glass transition and softening temperatures, viscosity, elastic modulus and hardness. In the present study, effect of TiO₂ addition on thermal and mechanical properties of Y-Si-Al-O-N glasses is investigated since the most typical Si₃N₄ ceramics for bearing applications are fabricated using a Si₃N₄-Y₂O₃-Al₂O₃-TiO₂-AlN system. Addition of TiO₂ is effective in preparing Y-Si-Al-O-N glasses with lower glass transition temperatures and with higher hardness.     

Electrical resistivity of silicon nitride-silicon carbide based ternary composites

New electrically conductive ternary composites were developed by adding 8 vol.% of ZrN or ZrB₂ to a Si₃N₄-SiC matrix. During hot pressing, ZrB₂ reacted with Si₃N₄ to form ZrSi₂, ZrN, Si and BN whereas added ZrN did not undergo any reactions in the Si₃N₄-SiC-ZrN composite. The composites modified by ZrN or ZrB₂ addition showed a lower resistivity (7 × 10³ Ω cm and 3 × 10⁻¹ Ω cm) compared to the matrix (3 × 10⁴ Ω cm). Further studies on the grain size distribution and the volume ratio of conducting and non-conducting phases excluded a percolation network of ZrN and ZrSi₂ grains. In fact, doping of SiC grains and modified grain boundaries as a consequence of the formation of liquid phases during sintering are suggested to be the reason for the significantly lower resistivity of materials containing ZrSi₂.A decrease in the composite resistivity due to a subsequent heat treatment was obtained for all hot-pressed composites.     

Indentation fracture resistance test round robin on silicon nitride ceramics

Reproducibility of indentation fracture resistance of three commercial silicon nitrides including bearing balls was evaluated by an international round robin with six laboratories. The between-laboratory standard deviations for indentations at 196 N on the perfectly mirror-finished surfaces were in the range of 0.2–0.5 MPa m^1/2, demonstrating an excellent precession of the test results. The scatter in the fracture resistance increased as the indentation load decreased from 196 to 98 N. The errors in measuring crack lengths deduced from the deviation of each laboratory's readings from author's reading for the same indentations tended to increase with a decrease in the magnification of the lab's microscope, which suggested that finding exact crack tips with lower magnification was difficult especially for those samples with insufficiently mirror-finished surfaces indented at 98 N. Observation of indentations at the load of 196 N with powerful optics was advised to ensure the validity of the indentation technique which is used as the quality assessment of Si₃N₄ bearing balls.     

Porous Si3N4 ceramics prepared via slip casting of Si and reaction bonded silicon nitride

Slip casting process combined with reaction bonded silicon nitride (RBSN) was used to prepare porous Si₃N₄ ceramic with near-net and complex shape. A butyl stearate (BS) coated process was introduced to restrain the hydrolysis of Si, and ammonium polyacrylate (NH₄PAA) was used to enhance the dispersion of coated Si. The measured oxygen content showed that the hydrolysis of Si was strongly prohibited by BS coating, and relatively low viscosity was obtained with the addition of 0.25-1.5 wt% NH₄PAA to the 60 wt% solid load slurry. 40-60 wt% solid load slurries were used for slip casting in the experiment. After vacuum degassing, slip casting, debindering and nitridation, a density of 1.57-1.92 g/cm³ (porosity 50.9-40%) and a flexural strength of 47-108 MPa were obtained. The samples without vacuum degassing showed a large number of nanowires grown in the large pores.     

Effect of TiO2 addition on the microstructures,mechanical and dielectric properties of porous Si3N4-based ceramics

Porous Si₃N₄-based ceramics with different TiO₂ contents were prepared by gas pressure sintering method. The effects of TiO₂ addition ranging from 0 to 25?wt-% on the phase compositions, microstructures, mechanical performance and dielectric properties were investigated. The addition of TiO₂ significantly promoted the density which increased from 1.64 to about 2.3?g?cm^?3. The mechanical properties of porous Si₃N₄-based ceramics with TiO₂ addition decreased first and then increased with the increase of TiO₂ content, and the flexural strength and elastic modulus are more than 167.4?MPa and 72.8?GPa, respectively, which were higher than that of the Si₃N₄ ceramic without TiO₂ addition. With the increase of TiO₂ content, both the dielectric constant and dielectric loss increased, and the dielectric constant enhanced obviously. These results suggested that the TiO₂ was beneficial for the improvement of mechanical properties and dielectric constant of porous Si₃N₄-based ceramics.     

Effect of carbon content on structural and mechanical properties of SiCN by atomistic simulations

Silicon carbonitride (SiCN) presents good performance on thermal stability and mechanical properties at high temperature. However, experiments still have problems to investigate the chemical structure of nanodomains and high temperature mechanical properties for SiCN. In this paper, atomistic simulations were used to generate amorphous SiCN with different carbon contents, the resulting structures show a tendency to include a “free carbon” phase when the carbon content increases. The calculated pair distributions, angular distributions and structure factor are comparable with experiments. Particularly, the first peaks of C-C and Si-C distributions become more significant when C content decreases, this is related to the variations of Si-C bonds near the graphene regions when the sizes of carbon phases change. The calculated Young's moduli are close to the experimental data and increase with increasing carbon content. The proposed atomic model can be used to predict the structural and mechanical properties of SiCN at different compositions.     

Relationship between fracture toughness determined by surface crack in flexure and fracture resistance measured by indentation fracture for silicon nitride ceramics with various microstructures

The reliability of the Vickers indentation fracture (IF) method for various types of silicon nitride (Si₃N₄) ceramics was assessed by comparing the fracture resistance, K_R obtained from the IF test with the fracture toughness, K_Ic from the surface crack in flexure (SCF) technique in the same crack depth region. The K_R of a fine-grained and equiaxed Si₃N₄ matched with the K_Ic from the SCF test when Miyoshi's equation was used, while the K_Ic of a bearing-grade Si₃N₄ was found to lie between K_R values calculated with Niihara's equation (higher side) and Miyoshi's equations (lower side). In the case of coarse Si₃N₄ with elongated grains, the K_R determined using Niihara's equation gave the best fit with K_Ic. The inconsistent outcomes were explained by the probable mechanisms, indicating that the K_R from the IF test cannot be correlated directly with the K_Ic unless the effective crack length for the IF test was clarified.     

In situ preparation of Si3N4–TiN composite by pyrolysis of polytitanosilazane (PTSZ)

Si₃N₄–TiN composite powders were obtained by in situ pyrolysis of polytitanosilazane. Dense Si₃N₄–TiN composites were prepared by hot-pressing at 1800 °C under 20 MPa for 2 h without sintering additive. Crystallization of amorphous PTSZ powders occurred between 1400 and 1500 °C with major phases, α-Si₃N₄, β-Si₃N₄, and small amount of phase TiN. Mechanical properties and microstructure of Si₃N₄–TiN composites were characterized. The results showed that the mechanical strength was 620 MPa, the fracture toughness was 7.8 MPa m^1/2 and the Vickers hardness was 8.5 GPa. SEM analysis indicated that Si₃N₄–TiN composite possessed excellent fracture toughness because TiN grains produced by in situ pyrolysis were well dispersed in Si₃N₄ matrix.     

Effect of carbonization on mechanical and tribological behavior of a copper-phenolic-based friction material

The effects of carbonization on the mechanical and tribological behavior of a copper/phenolic resin-based semi-metallic friction material were investigated. The results show that a lower carbonization rate leads to a material having higher compressive strength and hardness, as well as fewer cracks. A lower carbonization temperature results in a material with a weak XPS signal of the C-OH bond, while a higher carbonization temperature results in low C-H intensity and increased C-C intensity at the expense of C-H and CO/C-O groups. The material heat-treated to 400 °C has the highest compressive strength and hardness values. Heat-treating to higher temperature causes both values to decline. Both friction coefficient and wear are increased with increasing carbonization temperature. The material carbonized to 600 °C exhibits an optimum tribological performance. The worn surface of samples without heat treatment or heat-treated to lower temperatures is covered with a smooth but loosely-bonded layer of wear debris. Only a small amount of counter-face material is transferred to the sample surface. The worn surface of samples treated at higher temperatures is covered with rough sliding tracks. A significant amount of counter-face material is transferred onto the sample surface during the sliding. Carbonized samples demonstrate far better high-temperature heat/oxidation resistance than do non-carbonized samples.     

Mechanical,electrical, and thermal properties of graphene nanosheet/aluminum nitride composites

Graphene nanosheet (GNS)/aluminum nitride (AlN) composites were prepared by hot-pressing and effects of GNSs on their microstructural, mechanical, thermal, and electrical properties were investigated. At 1.49 vol% GNSs content, the fracture toughness (5.09 MPa m^1/2) and flexural strength (441 MPa) of the composite were significantly increased by 30.17% and 17.28%, respectively, compared to monolithic AlN. The electrical conductivity of the composites was effectively enhanced with the addition of GNSs, and showed a typical percolation behavior with a low percolation threshold of 2.50±0.4 vol%. The thermal conductivity of the composites decreased with the addition of GNSs.     

Effect of carbon nanoparticle reinforcement on mechanical and thermal properties of silicon carbide ceramics

This research presents an analysis of the influence of graphene reinforcement on the thermal and mechanical properties of silicon carbide ceramics, at 2.5% (wt%) graphene content. The SiC composites, containing various carbon nanofillers (graphene oxide and graphene nanoparticles), were sintered by the classical two stage spark plasma sintering method. Two current modes were used, the continuous mode and the pulsed current mode. The results from photothermal radiometry and investigations of the mechanical properties showed that graphene additives significantly improve the thermal properties and toughness of material, sintered from a SiC powder. An 45% growth in the toughness was observed, which increased from 1.21 to 1.75?MPa/m^1/2. The thermal diffusivity value also increased from 0.60 to 0.71?cm²/s and giving an improvement in thermal properties of 18%. The friction coefficient reached 7% giving an increase in value from 0.62 to 0.66. Microscopic investigations supported the photothermal radiometry (PTR) results. Whilst, thermal imaging revealed homogeneity of the local thermal properties of the products fabricated from the starting SiC powder.     

Processing of micro-components made of sintered reaction-bonded silicon nitride (SRBSN). Part 1: Factors influencing the reaction-bonding process

In order to establish a process for the manufacturing of injection moulded micro-components of sintered reaction-bonded silicon nitride (SRBSN) several process parameters were investigated with regard to their influence on the reaction-bonding step. One question to be answered was how the sintering aids affect the nitridation behaviour of a silicon green body. For the processing of micro-components it was of special interest to study, how a decreasing sample size and wall thickness would influence the rate of Si₃N₄ formation. By varying the added amounts of the sintering aids, it was found that increasing the Y₂O₃ and MgO contents both improved the nitridation rate, whereas an increase of Al₂O₃ content resulted in reduced nitridation rates. Within the investigated range of sample dimensions (0.2–4.0 g) the unexpected observation was made, that with decreasing sample weight the nitridation rate also decreased. This was explained by the exothermic nature of the reaction between Si and N₂ and the fact that small samples with a large surface-to-volume ratio attain thermal equilibrium with their environment better than large samples which may be subject to local overheating.     

Effect of SiC whiskers and graphene nanosheets on the mechanical properties of ZrB2-SiCw-Graphene ceramic composites

Ultrahigh temperature ZrB₂-SiC_w-Graphene ceramic composites are fabricated by hot pressing ZrB₂-SiC_w-Graphene oxide powders at 1950 °C and 30 MPa for 1 h. The microstructures of the composites are characterized by Scanning electron microscopy, Raman spectroscopy and X-ray diffraction. The results show that multilayer graphene nanosheets are achieved by thermal reduction of graphene oxide during sintering process. Compared with monolithic ZrB₂ materials, flexural strength and fracture toughness are both improved due to the synergistic effect of SiC whisker and graphene nanosheets. The toughening mechanisms mainly are the combination of SiC whisker and graphene nanosheets crack bridging, pulling out.     

Enhanced mechanical and dielectric behavior of BaTiO3/Cu composites

BaTiO₃/xCu composite ceramics with x = 0-30 wt.% were fabricated by the traditional mixing method in nitrogen gas. The mechanical properties and electric properties of the obtained composites were investigated as a function of the Cu mass fraction using a three bending test and impedance spectroscopy. The results indicated that the relative density of the sintered composites reached above 91%, the Cu-dispersed BaTiO₃ composites enhanced the mechanical properties, particularly the high fracture toughness (∼3.9 MPa m^1/2) and bending strength (∼134 MPa), compared to the monolithic BaTiO₃. Furthermore, the percolation threshold of BaTiO₃/Cu composites was x = 25 wt.%. The permittivity (?_r) markedly increased from ∼2000 for monolithic BaTiO₃ to ∼9000 with increasing Cu up to 30 wt.%. Additionally, the temperature coefficient of this system was less than 5% in the temperature range of 25-115.     

Investigation of the effect of ZrO2 and ZrO2/Al2O3 additions on the hot-pressing and properties of equimolecular mixtures of α- and β-Si3N4

In this work, hot-pressing of equimolecular mixtures of α- and β-Si₃N₄ was performed with addition of different amounts of sintering additives selected in the ZrO₂–Al₂O₃ system. Phase composition and microstructure of the hot-pressed samples was investigated. Densification behavior, mechanical and thermal properties were studied and explained based on the microstructure and phase composition. The optimum mixture from the ZrO₂–Al₂O₃ system for hot-pressing of silicon nitride to give high density materials was determined. Near fully dense silicon nitride materials were obtained only with the additions of zirconia and alumina. The liquid phase formed in the zirconia and alumina mixtures is important for effective hot-pressing. Based on these results, we conclude that pure zirconia is not an effective sintering additive. Selected mechanical and thermal properties of these materials are also presented. Hot-pressed Si₃N₄ ceramics, using mixtures from of ZrO₂/Al₂O₃ as additives, gave fracture toughness, K_IC, in the range of 3.7–6.2 MPa m^1/2 and Vicker hardness values in the range of 6–12 GPa. These properties compare well with currently available high performance silicon nitride ceramics. We also report on interesting thermal expansion behavior of these materials including negative thermal expansion coefficients for a few compositions.     

Mechanical properties of plasma sprayed nanostructured TiO2 coatings on mild steel

This paper discusses the effects of plasma spray parameters on the mechanical properties of nanostructured TiO₂ coatings deposited on mild steel substrates. The design of experiment method was applied to investigate the significant effects of each property and to optimize the operational spray parameters. Plasma power, powder feed rate, and stand-off distance were selected as independent variables. Agglomerated and sintered nano-TiO₂ powder was deposited on A-36 commercial mild steel. The microstructural and mechanical properties of the coatings such as porosity, microhardness, surface roughness, and wear rate were evaluated. Both plasma power and powder feed rate were found to be the main factors affecting all four responses. It was also noted that the stand-off distance was a significant factor mainly in influencing the surface roughness of the coatings. All in all, the optimized properties can be achieved by applying a plasma power of 30 KW (high level), a powder feed rate of 22 g/min (high level), and a stand-off distance of 80 mm (low level).