Steam reforming of methanol over Cu/ZnO/ZrO2/Al2O3 catalyst

Steam reforming of methanol was investigated over Cu–ZnO–ZrO₂–Al₂O₃ catalysts at 473 and 573 K. The Cu:Zn:(Al + Zr) molar ratio was 3:3:4; however, the Zr:Al molar ratio was varied and the catalysts were pretreated at different calcination and reduction temperatures. The synthesized catalysts were characterized by N₂ physisorption, temperature-programmed reduction with H₂ (H₂-TPR), X-ray diffraction, oxidized surface TPR, and infrared spectroscopy after carbon monoxide chemisorption. The crystalline size of Cu decreased on increasing the calcination temperatures from 573 to 623 K and increased on increasing the reduction temperatures from 523 to 573 K. Among the tested catalysts, the Cu–ZnO–ZrO₂ catalyst exhibited the highest and lowest hydrogen-formation rates at 473 and 573 K, respectively. After the reaction at 573 K, all the tested catalysts exhibited an increase in the Cu crystalline size, causing the catalyst deactivation. Among the tested catalysts, the Cu–ZnO–ZrO₂–Al₂O₃ catalyst, where the Cu:Zn:Al:Zr molar ratio was 3:3:2:2, showed the highest and most stable catalytic activity at 573 K. Cu dispersion and catalyst composition affected the catalytic performance for steam reforming of methanol.     

Effect of Al2O3 content on the adsorptive properties of Cu/ZnO/Al2O3 for removal of odorant sulfur compounds

Cu/ZnO/Al₂O₃ adsorbents for removal of odorant sulfur compounds were prepared with various Al/Cu molar ratios by co-precipitation method. The sulfur removing ability as a function of Al/Cu molar ratio of the adsorbents for t-butyl mercaptan (TBM), tetrahydro thiophene (THT), dimethyl disulfide (DMS) and H₂S were investigated at 250 °C and 6000 h⁻¹ space velocity. Based on the results of adsorption capacity and characterization by various techniques, the optimum Al/Cu ratio for maximum sulfur removal capacity is found to be at Al/Cu molar ratio of 0.15 which possesses the well-dispersed Cu species with high reducibility. The adsorption capacity is highest for H₂S followed by TBM, DMS and THT. The main role of Al₂O₃ component is to provide the dispersion of CuO species homogeneously with small particle formation and high reducibility.     

A synthesis of CO-tolerant Nb2O5-promoted Pt/C catalyst for direct methanol fuel cell; its physical and electrochemical characterization

A Pt-Nb₂O₅/C electrocatalyst was synthesized by a two-step process as an anode material in direct methanol fuel cell (DMFC). The Pt-Nb₂O₅/C catalysts heat-treated at different temperatures (400 and 500 °C) in flowing N₂ were characterized by various methods such as inductively coupled plasma-atomic emission spectroscopy, X-ray diffraction, transmission electron microscopy, and X-ray photoemission spectroscopy (XPS). The heat-treated Pt-Nb₂O₅/C catalyst at 400 °C showed the best electrochemical activity for CO and methanol oxidations among the prepared catalysts. The XPS results showed the electronic structure change of Pt, indicating a formation of interaction between Pt and Nb₂O₅. It is suggested that a synergistic effect between Pt and Nb₂O₅ enhances the electrocatalytic activity for CO and methanol oxidations. We believe that Nb₂O₅-promoted Pt/C catalyst may be regarded as one of the attractive candidates as an anode material in DMFC.     

Reforming of bioethanol over Ni/Al2O3 and Ni/CeZrO2/Al2O3 catalysts in supercritical water for hydrogen production

Bioethanol was reformed in supercritical water (SCW) at 500 °C and 25 MPa on Ni/Al₂O₃ and Ni/CeZrO₂/Al₂O₃ catalysts to produce high-pressure hydrogen. The results were compared with non-catalytic reactions. Under supercritical water and in a non-catalytic environment, ethanol was reformed to H₂, CO₂ and CH₄ with small amounts of CO and C2 gas and liquid products. The presence of either Ni/Al₂O₃ or Ni/CeZrO₂/Al₂O₃ promoted reactions of ethanol reforming, dehydrogenation and decomposition. Acetaldehyde produced from the decomposition of ethanol was completely decomposed into CH₄ and CO, which underwent a further water-gas shift reaction in SCW. This led to great increases in ethanol conversion and H₂ yield on the catalysts of more than 3-4 times than that of the non-catalytic condition. For the catalytic operation, adding small amounts of oxygen at oxygen to ethanol molar ratio of 0.06 into the feed improved ethanol conversion, at the expense of some H₂ oxidized to water, resulting in a slightly lower H₂ yield. The ceria-zirconia promoted catalyst was more active than the unpromoted catalyst. On the promoted catalyst, complete ethanol conversion was achieved and no coke formation was found. The ceria-zirconia promoter has important roles in improving the decomposition of acetaldehyde, the enhancement of the water-gas shift as well as the methanation reactions to give an extremely low CO yield and a tremendously high H₂/CO ratio. The SCW environment for ethanol reforming caused the transformation of gamma-alumina towards the corundum phase of the alumina support in the Ni/Al₂O₃ catalyst, but this transformation was slowed down by the presence of the ceria-zirconia promoter.     

Reactions over Cu/Nb2O5 catalysts promoted with Pd and Ru during hydrogen production from ethanol

Hydrogen production from reactions between ethanol and steam at 300 °C was evaluated under low conversion conditions for the Cu/Nb₂O₅ system promoted with Pd and Ru. Parallel reactions occurred on the surface of all samples as it was verified from the production of H₂, CO₂, CH₄, CO, C₂H₄, C₂H₆, C₂H₄O and (C₂H₅)₂O. Hydrogen production occurs mainly from ethanol dehydrogenation and secondly, from steam reforming and ethanol decomposition. Dehydration reactions were also identified and analyzed among others. Addition of Pd and Ru to the catalyst improves product selectivity and it was verified that Pd-Ru-Cu/Nb₂O₅ tri-metallic catalyst is the most promising for H₂ production due to its selectivity and lower deactivation, among all samples tested.     

Non-thermal plasma assisted synthesis and physicochemical characterizations of Co and Cu doped Ni/Al2O3 nanocatalysts used for dry reforming of methane

Ni/Al₂O₃ nanocatalysts doped with Co and Cu were prepared by co-impregnation and modified by non-thermal plasma. The nanocatalysts were characterized by XRD, FESEM, TEM, EDX dot-mapping, BET, FTIR, TGA-DTG, and XPS analysis. According to XRD and XPS results, good interaction between active phase and support can be observed in both Ni–Co/Al₂O₃ and Ni–Cu/Al₂O₃ nanocatalysts. A uniform morphology, high surface area, and well dispersed particles of active sites in Ni–Co/Al₂O₃ nanocatalyst were observed that shows the effect of cobalt in controlling Ni ensemble size. In contrast Ni–Cu/Al₂O₃ nanocatalyst had no homogenous dispersion of active phase due to sintering of copper particles. The activity measurements illustrated better Ni–Co/Al₂O₃ nanocatalyst activity in comparison to Ni/Al₂O₃ and Ni–Cu/Al₂O₃ in terms of CH₄ and CO₂ conversion. H₂ and CO yield were higher for Ni–Co/Al₂O₃ and higher H₂/Co ratio was obtained as well. Whereas Ni/Al₂O₃ and Ni–Co/Al₂O₃ did not experience deactivation, Ni–Cu/Al₂O₃ suffered from activity loss by ca. 22% and 16% for CH₄ and CO₂ conversion, respectively. Sintering most likely happened in Ni–Cu/Al₂O₃ nanocatalyst due to high temperature of calcination while cobalt by controlling the size of Ni particles, alternated the size of active sites to a size range in which carbon formation was suppressed. Ni/Al ratio from XPS analysis which signifies Ni dispersion on alumina support was 5.15, 9.16, and 6.35 for Ni/Al₂O₃, Ni–Co/Al₂O₃, and Ni–Cu/Al₂O₃ nanocatalysts respectively. The highest ratio of Ni/Al was for Ni–Co/Al₂O₃ nanocatalyst that shows the best coverage of support by Ni active phase in this nanocatalyst.     

Evaluation of Ni/Y2O3/Al2O3 catalysts for hydrogen production by autothermal reforming of methane

Ni/xY₂O₃–Al₂O₃ (x = 5, 10, 15, 20 wt%) catalysts were prepared by sequential impregnation synthesis. The catalytic performance for the autothermal reforming of methane was evaluated and compared with Ni/γ-Al₂O₃ catalyst. The physicochemical properties of catalysts were characterized by X-ray diffraction (XRD), Transmission electron microscope (TEM), X-Ray Photoelectron Spectrometer (XPS), Thermo Gravimetric Analyzer (TGA) and H₂-temperature programmed reduction techniques (TPR). The decrease of nickel particle size and the change of reducibility were found with Y modification. The CH₄ conversion increased with elevating levels of Y₂O₃ from 5% to 10%, then decreased with Y content from 10% to 20%. Ni/xY₂O₃–Al₂O₃ catalysts maintained high activity after 24 h on stream, while Ni/Al₂O₃ had a significant deactivation. The characterization of spent catalysts indicated that the addition of Y retarded Ni sintering and decreased the amount of coke.     

Nickel on a macro-mesoporous Al2O3@ZrO2 core/shell nanocomposite as a novel catalyst for CO methanation

A novel nickel catalyst supported on Al₂O₃@ZrO₂ core/shell nanocomposites was prepared by the impregnation method. The core/shell nanocomposites were synthesized by depositing zirconium species on boehmite nanofibres. This contribution aims to study the effects of the pore structure of supports and the zirconia dispersed on the surface of the alumina nanofibres on the CO methanation. The catalysts and supports were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), H₂ temperature-programmed reduction (H₂-TPR), nitrogen adsorption–desorption, and thermogravimetry and differential thermal analysis (TG-DTA). The catalytic performance of the catalysts for CO methanation was investigated at a temperature range from 300 °C to 500 °C. The results of the characterization indicate that the metastable tetragonal zirconia could be stably and evenly dispersed on the surface of alumina nanofibres. The interlaced nanorods of the Al₂O₃@ZrO₂ core/shell nanocomposites resulted in a macropore structure and the spaces between the zirconia nanoparticles dispersed on the alumina nanofibres formed most of the mesopores. Zirconia on the surface of the support promoted the dispersion and influenced the reduction states of the nickel species on the support, so it prevented the nickel species from sintering as well as from forming a spinel phase with alumina at high temperatures, and thus reduced the carbon deposition during the reaction. With the increase of the zirconia content in the catalyst, the catalytic performance for the CO methanation was enhanced. The Ni/Al₂O₃@ZrO₂-15 exhibited the highest CO conversion and methane selectivity at 400 °C, but they decreased dramatically above or below 400 °C due to the temperature sensitivity of the catalyst. Ni/Al₂O₃@ZrO₂-30 exhibited a high and constant rate of methane formation between 350 °C and 450 °C. The excellent catalytic performance of this catalyst is attributed to its reasonable pore structure and good dispersion of zirconia on the support. This catalyst has great potential to be further studied for the future industrial use.     

Methanol steam reforming in an Al2O3 supported thin Pd-layer membrane reactor over Cu/ZnO/Al2O3 catalyst

In this experimental study, a membrane reactor housing a composite membrane constituted by a thin Pd-layer supported onto Al₂O₃ is utilized to perform methanol steam reforming reaction to produce high-grade hydrogen for PEM fuel cell applications. The influence of various parameters such as temperature, from 280 to 330 °C, and pressure, from 1.5 to 2.5 bar, is analyzed. A commercial Cu/Zn-based catalyst is packed in the annulus of the membrane reactor and the experimental tests are performed at space velocity equal to 18,500 h⁻¹ and H₂O:CH₃OH feed molar ratio equal to 2.5:1. Results in terms of methanol conversion, hydrogen recovery, hydrogen yield and products selectivities are given. As a best result of this work, 85% of methanol conversion and a highly pure hydrogen stream permeated through the membrane with a CO content lower than 10 ppm were reached at 330 °C and 2.5 bar. Furthermore, a comparison between the experimental results obtained in this work and literature data is proposed and discussed.     

Electrochromic properties of Nb2O5 sol–gel coatings

Sol–gel niobium oxide coatings are promising electrochromic materials. The sols have been prepared by a sonocatalytic mixing of NbCl₅ powder, butanol and acetic acid. Thermal analysis (DTA/TG) coupled to mass spectrometry has been performed on Nb₂O₅ precipitates to quantitatively analyse the effluents. Transparent and defect-free single and multilayers coatings have been deposited on ITO-coated glass by a dip-coating process and then calcined between 400°C and 600°C. The coatings structure change from amorphous to crystalline (TT form) and the later ones are highly textured. The films present a reversible and fast insertion/extraction kinetics for Li⁺ ions. After insertion the amorphous coatings present a grey-brown color, while the crystalline ones are dark blue. The maximum charge density exchanged with a three-layer 200 nm thick coating sintered at 600°C was 16 mC/cm² with a corresponding spectral transmission change practically wavelength-independent varying from 80% to 20%. The coloring efficiency determined at λ=600 nm was 22 cm²/C.     

Catalytic properties of Ag promoted ZnO/Al2O3 catalysts for hydrogen production by steam reforming of ethanol

Ag promoted ZnO/Al₂O₃ catalysts were prepared by using the incipient wetness impregnation method. The catalytic properties of steam reforming reaction for hydrogen production on the prepared catalysts were evaluated with H₂O:C₂H₅OH molar ratios of 3:1 at 450 °C and atmospheric pressure. Ag promoted ZnO/Al₂O₃ catalysts show higher SRE catalytic activity than ZnO/Al₂O₃ catalysts. H₂ and CH₃CHO are the major products on Ag promoted catalysts, and C₂H₄ is also produced probably due to acid sites on Al₂O₃. SRE mechanism on Ag promoted ZnO/Al₂O₃ catalysts, which contains C-C scission, is different from that on ZnO/Al₂O₃ catalysts. A method based on thermogravimetry (TG), differential scanning calorimetry (DSC) and mass spectrometry (MS) was used to analysis the coking behavior on catalyst surface. The surfaces of Ag promoted ZnO/Al₂O₃ catalysts show two different types of coking, and suffer higher coke deposition during the steam reforming reaction.     

Effects of modifying Ni/Al2O3 catalyst with cobalt on the reforming of CH4 with CO2 and cracking of CH4 reactions

Alumina supported nickel (Ni/Al₂O₃), nickel–cobalt (Ni–Co/Al₂O₃) and cobalt (Co/Al₂O₃) catalysts containing 15% metal were synthesized, characterized and tested for the reforming of CH₄ with CO₂ and CH₄ cracking reactions. In the Ni–Co/Al₂O₃ catalysts Ni–Co alloys were detected and the surface metal sites decreased with decrease in Ni:Co ratio. Turnover frequencies of CH₄ were determined for both reactions. The initial turnover frequencies of reforming (TOF_DRM) for Ni–Co/Al₂O₃ were greater than that for Ni/Al₂O₃, which suggested a higher activity of alloy sites. The initial turnover frequencies for cracking (TOF_CRK) did not follow this trend. The highest average TOF_DRM, H₂:CO ratio and TOF_CRK were observed for a catalyst containing a Ni:Co ratio of 3:1. This catalyst also had the maximum carbon deposited during reforming and produced the maximum reactive carbon during cracking. It appeared that carbon was an intermediate product of reforming and the best catalyst was able to most effectively crack CH₄ and oxidize carbon to CO by CO₂.     

Optimisation of the electrochromic properties of Nb2O5 thin films produced by sol–gel route using factorial design

Electrochemical and electrochromical properties of oxide films are dependent on their microstructure and morphological properties. Thus, the effects of three preparation variables on the electrochemical and electrochromical properties of Nb₂O₅ thin films prepared by the Pechini method were investigated. In order to minimise the number of experiments, a factorial design 2³ was used. The effects of the following variables: CA/EG molar ratio, CA/[Nb] molar ratio and calcination temperature were evaluated. Films prepared with the resin composition CA/EG=1 : 4, CA/[Nb]=10 : 1 and calcined at 500°C, showed the highest values of intercalation charge, transmittance variation and coloration efficiency, 22 mC/cm², 84% and 23 cm² C⁻¹, respectively.     

Al2O3-coated nanoporous TiO2 electrode for solid-state dye-sensitized solar cell

This paper reports the preparation of a core-shell nanoporous electrode consisting of an inner TiO₂ porous matrix and a thin overlayer of Al₂O₃, and its application for solid-state dye-sensitized solar cell using p-CuI as hole conductor. Al₂O₃ overlayer was coated onto TiO₂ porous film by the surface sol–gel process. The role of Al₂O₃ layer thickness on the cell performance was investigated. The solar cells fabricated from Al₂O₃-coated electrodes showed superior performance to the bare TiO₂ electrode. Under illumination of AM 1.5 simulated sunlight (89 mW/cm²), a ca. 0.19 nm Al₂O₃ overlayer increased the photo-to-electric conversion efficiency from 1.94% to 2.59%.     

Fabrications and evaluations of hydrogen permeation on Al2O3/CeO2/graphene (ACG) composites membrane by Hot Press Sintering (HPS)

Ceramic membrane has high permeation rate of hydrogen and chemical stability. Al₂O₃ indicates stable at high temperature and a relatively large surface area. In addition, Al₂O₃ of porous is used as hydrogen separation membranes support, because of the high hydrogen permeability based on Knudsen diffusion mechanism.     

Hydroprocessing of Jatropha oil over NiMoCe/Al2O3 catalyst

The non-sulfided NiMoCe/Al₂O₃ catalyst was developed to produce green diesel from the hydroprocessing of Jatropha oil. The NiMoCe/Al₂O₃ catalysts were prepared by impregnation and characterized by N₂-BET, SEM, XRD and TPD-H_ads techniques. The straight chain alkanes ranging from C15 to C18 were the main components in product oil. The maximum yield of C15-C18 alkanes of 80%, selectivity of 90% and conversion of 89% were obtained at 370 °C, 3.5 MPa and 0.9 h⁻¹. Influence of reaction temperature (280–400 °C) and reaction time (10–163 h) on the composition of product oil were discussed. The experimental results demonstrated that a suitable amount of metal Ce doping on the NiMo/Al₂O₃ catalyst presented stable catalytic performance and enhanced Jatropha oil conversion as well as C15-C18 fraction selectivity.     

Photocatalytic hydrogen production from aqueous methanol solution with CuO/Al2O3/TiO2 nanocomposite

The photocatalytic hydrogen production from aqueous methanol solution was investigated with ZnO/TiO₂, SnO/TiO₂, CuO/TiO₂, Al₂O₃/TiO₂ and CuO/Al₂O₃/TiO₂ nanocomposites. A mechanical mixing method, followed by the solid-state reaction at elevated temperature, was used for the preparation of nanocomposite photocatalyst. Among these nanocomposite photocatalysts, the maximal photocatalytic hydrogen production was observed with CuO/Al₂O₃/TiO₂ nanocomposites. A variety of components of CuO/Al₂O₃/TiO₂ photocatalysts were tested for the enhancement of H₂ formation. The optimal component was 0.2 wt% CuO/0.3 wt% Al₂O₃/TiO₂. The activity exhibited approximately tenfold enhancement at the optimum loading, compared with that with pure P-25 TiO₂. Nano-sized TiO₂ photocatalytic hydrogen technology has great potential for low-cost, environmentally friendly solar-hydrogen production to support the future hydrogen economy.     

Hydrogen production by steam reforming of model bio-oil using structured Ni/Al2O3 catalysts

This study focuses on hydrogen production from the steam reforming of model bio-oil over Ni/Al₂O₃ catalysts prepared in two different geometries (monolith and pellet) using the dip-coating and wet impregnation methods and characterized using Powder X-Ray diffraction, Temperature Programmed Reduction, Scanning Electron Microscopy (SEM) and BET Surface area analysis. The effects of the catalyst geometry and reforming temperatures were studied by carrying out experiments at the optimal conditions of T = (823, 923, 1023) K and S/C ratio = 13 determined from the thermodynamic analysis of the process prior to the experiments using the process simulator PRO-II. The experimental results showed high steady state H₂ yield corresponding to 2.58 and 1.73 mol (out of 5.13 mol) using monolithic and the pelletized catalysts respectively. The product distribution achieved with the monolithic catalyst was closer to the thermodynamic results suggesting a higher selectivity to hydrogen production.     

Comparative study of CeO2/CuO and CuO/CeO2 catalysts on catalytic performance for preferential CO oxidation

The CeO₂/CuO and CuO/CeO₂ catalysts were synthesized by the hydrothermal method and characterized via XRD, SEM, H₂-TPR, HRTEM, XPS and N₂ adsorption–desorption techniques. The study shows that the rod-like structure is self-assembled CeO₂, and both hydrothermal time and Ce/Cu molar ratio are important factors when the particle-like CeO₂ is being self-assembled into the rod-like CeO₂. The CuO is key active component in the CO-PROX reaction, and its reduction has a negative influence on the selective oxidation of CO. The advantage of the inverse CeO₂/CuO catalyst is that it still can provide sufficient CuO for CO oxidation before 200 °C in the hydrogen-rich reductive gasses. The traditional CuO/CeO₂ catalyst shows better activity at lower temperature and the inverse CeO₂/CuO catalysts present higher CO₂ selectivity when the CO conversion reaches 100%. The performance of mixed sample verifies that they might be complementary in the CO-PROX system.     

Charge–discharge characteristics of all-solid-state thin-filmed lithium-ion batteries using amorphous Nb2O5 negative electrodes

All-solid-state thin-filmed lithium-ion rechargeable batteries composed of amorphous Nb₂O₅ negative electrode with the thickness of 50–300 nm and amorphous Li₂Mn₂O₄ positive electrode with a constant thickness of 200 nm, and amorphous Li₃PO_4−xN_x electrolyte (100 nm thickness), have been fabricated on glass substrates with a 50 mm × 50 mm size by a sputtering method, and their electrochemical characteristics were investigated. The charge–discharge capacity based on the volume of positive electrode increased with increasing thickness of negative electrode, reaching about 600 mAh cm⁻³ for the battery with the negative electrode thickness of 200 nm. But the capacity based on the volume of both the positive and negative electrodes was the maximum value of about 310 mAh cm⁻³ for the battery with the negative electrode thickness of 100 nm. The shape of charge–discharge curve consisted of a two-step for the batteries with the negative electrode thickness more than 200 nm, but that with the thickness of 100 nm was a smooth S-shape curve during 500 cycles.