SiCn/SiC oxidation protective coating for carbon/carbon composites

Nano-SiC (SiC_n) coating was deposited on SiC pre-coated C/C composites by a hydrothermal electrophoretic deposition. The phase compositions, surface and cross-section microstructures, and anti-oxidation properties of the multilayer coatings were investigated. Results show that hydrothermal electrophoretic deposition is an effective route to prepare smooth and homogeneous SiC_n coating on SiC-C/C composites. The as-prepared SiC_n/SiC multilayer coatings can effectively protect C/C composites from oxidation in air at 1773 K for 202 h with a weight loss of 0.79% and at 1873 K for 64 h with a weight loss of 1.3%.     

Effect of the surface microstructure of SiC inner coating on the bonding strength and ablation resistance of ZrB2-SiC coating for C/C composites

The present study has been conducted in order to investigate the effect of the surface morphology of SiC inner coating on the bonding strength and ablation resistance of the sprayed ZrB₂-SiC coating for C/C composites. The microstructure of SiC inner coatings prepared by chemical vapor deposition and pack cementation at different temperatures were analyzed by X-ray diffraction, scanning electron microscopy, and 3D Confocal Laser Scanning Microscope. Tensile bonding strength and oxyacetylene ablation testing were used to characterize the bonding strength and ablation resistance of the sprayed ZrB₂-SiC coating, respectively. Results show that SiC inner coating prepared by chemical vapor deposition has a smooth surface, which is not beneficial to improve the bonding strength and ablation resistance of the sprayed ZrB₂-SiC coating. SiC inner coating prepared by pack cementation at 2000 °C has a rugged surface with the roughness of 72.15 µm, and the sprayed ZrB₂-SiC coating with it as inner layer exhibits good bonding strength and ablation resistance.     

Wear behavior of SiC nanowire-reinforced SiC coating for C/C composites at elevated temperatures

To improve the wear resistance of SiC coating on carbon/carbon (C/C) composites, SiC nanowires (SiCNWs) were introduced into the SiC wear resistant coating. The dense SiC nanowire-reinforced SiC coating (SiCNW-SiC coating) was prepared on C/C composites using a two-step method consisting of chemical vapor deposition and pack cementation. The incorporation of SiCNWs improved the fracture toughness of SiC coating, which is an advantage in wear resistance. Wear behavior of the as-prepared coatings was investigated at elevated temperatures. The results show that the wear resistance of SiCNW-SiC coating was improved significantly by introducing SiC nanowires. It is worth noting that the wear rate of SiCNW-SiC coating was an order of magnitude lower than that of the SiC coating without SiCNWs at 800 °C. The wear mechanisms of SiCNW-SiC coating at 800 °C were abrasive wear and delamination. Pullout and breakage of SiC grains resulted in failure of SiC coating without SiCNWs at 800 °C.     

Microstructure and oxidation resistance of C-AlPO4–mullite coating prepared by hydrothermal electrophoretic deposition for SiC-C/C composites

Oxidation resistant C-AlPO₄–mullite coating for SiC pre-coated carbon/carbon composites (SiC-C/C) was prepared by a novel hydrothermal electrophoretic deposition process. The phase composition, surface and cross-section microstructure of the as-prepared multi-layer coatings were characterized by X-ray Diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). The influence of deposition voltage on phase composition, microstructure and oxidation resistance of the as-prepared coatings was particularly investigated. Results show that the outer layer coating mainly composed of C-AlPO₄ and mullite phase can be achieved after the hydrothermal electrophoretic deposition. The thickness, density and anti-oxidation property of the C-AlPO₄–mullite coating was improved with the increase of deposition voltage from 160 V to 200 V. The multi-layer coating prepared at a voltage of 200 V exhibit excellent anti-oxidation property, which can effectively protect C/C composites from oxidation in air at 1773 K for 324 h with a weight loss of 1.01%. The failure of the multi-layer coatings is due to the generation of cross-holes in the coating, which cannot be self-cured by the metaphosphate and silicate glass layer after long time oxidation at 1773 K.     

HfC nanowires to improve the toughness and oxidation resistance of Si-Mo-Cr/SiC coating for C/C composites

To improve the oxidation resistance of carbon/carbon (C/C) composites, a dense HfC nanowire-toughened Si-Mo-Cr/SiC multilayer coating was prepared by chemical vapor deposition (CVD) and pack cementation. The microstructure, thermal shock and isothermal oxidation resistance of the coating were investigated. HfC nanowires could improve the toughness of the coating and suppress the coating cracking. After incorporating HfC nanowires in the coating, both of the thermal shock and isothermal oxidation resistance of the coating were obviously improved. The multilayer coating with HfC nanowires could effectively protect C/C composites at 1773 K for 270 h, whose weight loss is only 0.19%. The good oxidation resistance is mainly attributed to the formation of a compound glass layer containing SiO₂ and Cr₂O₃.     

A mullite/SiC oxidation protective coating for carbon/carbon composites

To protect carbon/carbon (C/C) composites against oxidation, a mullite coating was prepared on SiC precoated C/C composites by a hydrothermal electrophoretic deposition process. The phase composition, microstructure and oxidation resistance of the prepared mullite/SiC coatings were investigated. Results show that hydrothermal electrophoretic deposition is an effective route to achieve crack-free mullite coatings. The mullite/SiC coating displays excellent oxidation resistance and can protect C/C composites from oxidation at 1773 K for 322 h with a weight loss rate of only 4.89 × 10^?4 g/cm² h. The failure of the multi-layer coatings is considered to be caused by the volatilization of silicate glass layer, the formation of microholes and microcracks on the coating surface and the formation of penetrative holes between the SiC bonding layer and the C/C matrix at 1773 K. The corresponding high temperature oxidation activation energy of the coated C/C composites at 1573–1773 K is calculated to be 111.11 kJ/mol.     

Dynamic oxidation resistance and residual mechanical strength of ZrB2-CrSi2-SiC-Si/SiC coated C/C composites

To improve oxidation resistance of carbon/carbon (C/C) composites, a multiphase double-layer ZrB₂-CrSi₂-SiC-Si/SiC coating was prepared on the surface of C/C composites by pack cementation. Thermogravimetry analysis showed that the as-prepared coating could provide effective oxidative protection for C/C composites from room temperature to 1490 °C. After thermal cycling between 1500 °C and room temperature, the fracture behaviors of the as-prepared specimens changed and their residual flexural strengths decreased as thermal cycles increased. The specimen after 20 thermal cycles presented pseudo-plastic fracture characteristics and relatively high residual flexural strength (83.1%), while the specimen after 30 thermal cycles failed catastrophically without fiber pullout due to the severe oxidation damage of C/C substrate especially the brittleness of the reinforcement fibers.     

工艺因素对水热电泳沉积硅酸钇涂层显微结构的影响

采用水热电泳沉积法在C/C-SiC复合材料表面制备了硅酸钇抗氧化外涂层.研究了沉积电流密度和低温热处理对硅酸钇涂层的影响.采用X-射线衍射仪(XRD)和扫描电子显微镜(SEM)对涂层的相组成和显微结构进行了表征.结果表明:采用声化学法制备的硅酸钇微晶颗粒尺寸为25～40nm.随着沉积电流密度增加,硅酸钇涂层均匀性、致密性先逐渐增加后降低.当电流密度超过0.04 A/cm2时会导致涂层表面开裂.进行低温热处理,涂层表面硅酸钇纳米晶出现熔融现象;随热处理温度增加,涂层表面呈现玻璃化趋势.当热处理温度达1200℃时,表面完全熔融,形成致密的硅酸钇玻璃层.涂层在1500℃静态空气中,经过氧化10 h后,失重仍然小于2%.     

TaB2–SiC–Si multiphase oxidation protective coating for SiC-coated carbon/carbon composites

To improve the oxidation resistance of the carbon/carbon (C/C) composites, a TaB₂–SiC–Si multiphase oxidation protective ceramic coating was prepared on the surface of SiC coated C/C composites by pack cementation. Results showed that the outer multiphase coating was mainly composed of TaB₂, SiC and Si. The multilayer coating is about 200 μm in thickness, which has no penetration crack or big hole. The coating could protect C/C from oxidation for 300 h with only 0.26 × 10^?2 g²/cm² mass loss at 1773 K in air. The formed silicate glass layer containing SiO₂ and tantalum oxides can not only seal the defects in the coating, but also reduce oxygen diffusion rates, thus improving the oxidation resistance.     

Microstructures and oxidation behaviors of Al-modified and Al2O3-modified SiC coatings on carbon/carbon composites via pack cementation

Al₂O₃-modified SiC (AOSC) and Al-modified SiC (ASC) coatings were prepared on carbon/carbon (C/C) composites by one-time pack cementation (PC). Their microstructures and anti-oxidation performances were studied. Compared with ASC coating, AOSC coating shows more conspicuous defects (micro-cracks and holes) and lower densification. ASC coating can offer better oxidation resistance and thermal shock resistance to C/C composites than AOSC coating. Al additive can more efficiently improve the sinterability of SiC, which causes the above results. Besides, Al₂O₃ oxidation product is more stable than SiO₂ (l) of oxidized SiC at 1500 °C based on the thermodynamic analysis.     

A MoSi2-SiOC-Si3N4/SiC anti-oxidation coating for C/C composites prepared at relatively low temperature

In this study, SiC coating for C/C composites was prepared by pack cementation method at 1773 K, and MoSi₂-SiOC-Si₃N₄ as an outer coating was successfully fabricated on the SiC coated samples by slurry method at 1273 K. The microstructure and phase composition of the coatings were analyzed. Results showed that a porous β-SiC inner coating and a crack-free MoSi₂-SiOC-Si₃N₄ coating are formed. Effect of Si₃N₄ content on the oxidation resistance of the coated C/C composites at 1773 K in air was also investigated. The weight loss curves revealed that introducing the appropriate proportion of Si₃N₄ could improve the oxidation resistance of coating. The MoSi₂-SiOC/SiC coated C/C sample had an accelerated weight loss after oxidation in air for 20 h. However, the coating containing 45% Si₃N₄ could protect C/C composition from oxidation for 100 h with a minute weight loss of 0.63%.     

SiC nanowire-toughened MoSi2-WSi2-SiC-Si multiphase coating for improved oxidation resistance of C/C composites

To improve the oxidation resistance of carbon/carbon (C/C) composites at high temperature, a SiC nanowire-toughened MoSi₂-WSi₂-SiC-Si multiphase coating was prepared by chemical vapor deposition (CVD) and pack cementation. The microstructure, mechanical properties and oxidation resistance of the coating were investigated. After the introduction of SiC nanowires, the elastic modulus, hardness, and fracture toughness of the MoSi₂-WSi₂-SiC-Si coating were increased by 25.48%, 4.09% and 45.03%, respectively. The weight loss of the coated sample with SiC nanowires was deceased from 4.83–2.08% after thermal shock between 1773 K and room temperature for 30 cycles and the weight loss is only 3.24% after isothermal oxidation at 1773 K in air for 82 h. The good oxidation resistance of the coating is mainly attributed to that SiC nanowires can effectively inhibit the propagation of cracks in the coating by the toughening mechanisms including bridging and pull-out.     

Polymer-derived yttrium silicate coatings on 2D C/SiC composites

Yttrium silicate environmental barrier coatings (EBCs) on C/SiC composites were fabricated by using polysiloxanes-derived ceramic process. In order to reduce the free silica in the resultant ceramic coatings, Y₂O₃ was added as an active filler. The materials with different weight ratios of polysiloxanes to Y₂O₃ were synthesized. Their coefficient of thermal expansion (CTE) and water-vapor resistance were tested. The results indicated that the composition of 50% Y₂O₃–50% polysiloxanes (Y50) was suitable to be the EBCs for C/SiC composites. The C/SiC composites coated with Y50 were tested in the water-vapor environments at 1400 °C for 200 h. The results revealed that such a coating could effectively protect the C/SiC composites.     

碳/碳复合材料表面SiC/c-AlPO_4复合涂层及其抗氧化机制

采用二次包埋法和水热电泳沉积法相结合的工艺在碳纤维增强碳复合材料表面制得SiC/方石英型磷酸铝(cristobalite aluminum phosphate,c-AlPO4)复合涂层。借助X射线衍射仪和扫描电镜对复合涂层的晶相组成和显微结构进行了表征。研究了复合涂层的高温氧化性能,讨论了复合涂层氧化、失效的机理。结果表明:复合涂层具有双层结构,包埋的SiC内层主要由α-SiC,β-SiC和少量的游离硅组成,外层由c-AlPO4颗粒构成,内外层结合紧密。复合涂层在1300～1500℃范围内具有良好的抗氧化性能,其氧化激活能为117.2kJ/mol,氧化过程主要受氧在c-AlPO4层中的体扩散速率所控制;氧化气体逸出留下的孔洞是复合涂层防氧化失效的主要原因。     

Effect of silicon/graphite ratio and temperature on oxidation protective properties of SiC/ZrB2–SiC coatings prepared by pack cementation

To investigate the silicon/graphite ratio and temperature on preparation and properties of ZrB₂–SiC coatings, ZrB₂, silicon, and graphite powders were used as pack powders to prepare ZrB₂–SiC coatings on SiC coated graphite samples at different temperatures by pack cementation method. The composition, microstructure, thermal shock, and oxidation resistance of these coatings were characterized and assessed. High silicon/graphite ratio (in this case, 2) did not guarantee higher coating density, instead could be harmful to coating formation and led to the lump of pack powders, especially at temperatures of 2100 and 2200 °C. But residual silicon in the coating is beneficial for high density and oxidation protection ability. The SiC/ZrB₂–SiC (ZS50-2) coating prepared at 2000 °C showed excellent oxidation protective ability, owing to the residual silicon in the coating and dense coating structure. The weight loss of ZS50-2 after 15 thermal shocks between 1500 °C and room temperature, and oxidation for 19 h at 1500 °C are 6.5% and 2.9%, respectively.     

Oxidation resistance of SiC nanowires reinforced SiC coating prepared by a CVD process on SiC‐coated C/C composites

Oxidation protective SiC nanowires‐reinforced SiC (SiCNWs‐SiC) coating was prepared on pack cementation (PC) SiC‐coated carbon/carbon (C/C) composites by a simple chemical vapor deposition (CVD) process. This double‐layer SiCNWs‐SiC/PC SiC‐coating system on C/C composites not only has the advantages of SiC buffer layer but also has the toughening effects of SiCNWs. The microstructure and phase composition of the nanowires and the coatings were examined by SEM, TEM, and XRD. The single‐crystalline β‐SiC nanowires with twins and stacking faults were deposited uniformly and oriented randomly with diameter of 50‐200 nm and length ranging from several to tens micrometers. The dense SiCNWs‐SiC coating with some closed pores was obtained by SiC nanocrystals stacked tightly with each other on the surface of SiCNWs. After introducing SiCNWs in the coating system, the oxidation resistance is effectively improved. The oxidation test results showed that the weight loss of the SiCNWs‐SiC/PC SiC‐coated samples was 4.91% and 1.61% after oxidation at 1073 K for 8 hours and at 1473 K for 276 hours, respectively. No matter oxidation at which temperature, the SiCNWs‐SiC/PC SiC‐coating system has better anti‐oxidation property than the single‐layer PC SiC coating or the double‐layer CVD SiC/PC SiC coating without SiCNWs.     

Effect of SiC nanowires on the thermal shock resistance of joint between carbon/carbon composites and Li2O–Al2O3–SiO2 glass ceramics

In order to improve the bonding property of joint between SiC modified carbon/carbon (C/C) composites and Li₂O–Al₂O₃–SiO₂ (LAS) glass ceramics, SiC nanowires were attempted as the reinforcement materials in the interface region of SiC transition layer and Li₂O–MgO–Al₂O₃–SiO₂ (LMAS) gradient joining interlayer. The C/C–LAS joint with SiC nanowire-reinforced interface layer was prepared by a three-step technique of pack cementation, in situ reaction and hot-pressing. The microstructure and thermal shock resistance of the as-prepared joints were examined. The average shear strength of the joined samples with SiC nanowires increased from 24.9 MPa to 31.6 MPa after 40 thermal cycles between 1000 °C and room temperature, while that of the joined samples without SiC nanowires dropped from 21.4 MPa to 8.3 MPa. The increase of thermal shock resistance of the C/C–LAS joints was mainly attributed to the toughening mechanism of SiC nanowires by pullout, bridging and crack deflection.     

固渗+EB-PVD法制备炭/炭复合材料防氧化复合涂层研究

制备出了SiC/SiC-Al2O3-Y2O3炭/炭复合材料防氧化复合涂层,该复合涂层的内层SiC基涂层采用料浆固渗法制备,SiC-Al2O3-Y2O3外层涂层采用大功率电子束物理气相沉积法。研究表明,电子束物理气相沉积法能达到较好的沉积效果,在制备过程中形成了柱状晶结构的涂层,使得涂层具有更高的应变容限,涂层非常均匀致密。用SEM、XPS和EDS等分析方法分析了涂层的防氧化机理。结果表明:在制备过程和氧化过程中,涂层内会发生复杂的物理和化学变化,生成硅酸盐氧化物,显示出电子束物理气相沉积法在制备炭/炭复合材料防氧化涂层方面独特的优势。     

Oxidation protection of C/C composites with a multilayer coating of SiC and Si + SiC + SiC nanowires

An oxidation protective Si–SiC coating with randomly oriented SiC nanowires was prepared on the SiC-coated carbon/carbon (C/C) composites by a two-step technique. First, a porous network of SiC nanowires was produced using chemical vapor deposition. This material was subjected to pack cementation to infiltrate the porous layer with a mixture of Si and SiC. The nanowires in the coating could efficiently suppress the cracking of the coating by various toughening mechanisms including nanowire pullout, nanowire bridging, microcrack deflection and good interaction between nanowire/matrix interface. The results of thermogravimetric analysis and thermal shock showed that the coating had excellent oxidation protection for C/C composites between room temperature and 1500 °C. These results were confirmed by two additional oxidation experiments conducted at temperature of 900 and 1400 °C, which demonstrated that the coating could efficiently protect C/C composites from oxidation at 900 °C for more than 313 h or at 1400 °C for more than 112 h.     

Oxidation behavior of oxidation protective coatings for PIP-C/SiC composites at 1500 °C

Three-dimensional carbon fiber reinforced silicon carbide (C/SiC) composites were fabricated by precursor infiltration and pyrolysis (PIP) with polycarbosilane as the matrix precursor, SiC coating prepared by chemical vapor deposition (CVD) and ZrB₂-SiC/SiC coating prepared by CVD with slurry painting were applied on C/SiC composites, respectively. The oxidation of three samples at 1500 °C was compared and their microstructures and mechanical properties were investigated. The results show that the C/SiC without coating is distorted quickly. The mass loss of SiC coating coated sample is 4.6% after 2 h oxidation and the sample with ZrB₂-SiC/SiC multilayer coating only has 0.4% mass loss even after oxidation. ZrB₂-SiC/SiC multilayer coating can provide longtime protection for C/SiC composites. The mode of the fracture behavior of C/SiC composites was also changed. When with coating, the fracture mode of C/SiC composites became brittle. When after oxidation, the fracture mode of C/SiC composites without and with coating also became brittle.