Protective nature of nano-TiN coatings shaped by EPD on Ti substrates

The hardness and corrosion resistance of TiN coatings, processed by Electrophoretic Deposition (EPD) to cover polished and unpolished Ti substrates, have been evaluated. A deposition time of 5 min has been enough to obtain a cohesive layer of 7–8 μm in thickness. The coatings were thermally treated in vacuum atmosphere at 1200 °C for 1 h with heating and cooling rates of 5 °C min^?1. The surfaces have been covered homogeneously optimizing the properties of the Ti substrates. Uniform and dense TiN coatings have been obtained onto polished substrates, while on unpolished Ti the nitrogen diffuses toward the substrate, moderately dissolving TiN coating. The nanohardness values of the polished samples have been increased from 2.8–4.8 GPa up to 6.5–8.5 GPa. Besides, the corrosion current density has been reduced more than one order of magnitude obtaining a protective efficiency of 82%. These values have been compared with other works in literature where authors used complex and costly processing techniques, demonstrating the strong impact of the colloidal processing over the specific properties of the material.     

Anti-adhesion performance of various nitride and DLC films against high strength steel in metal forming operation

High strength steel (HSS) is widely used for automobile reinforcement parts and the quantity required is rapidly grown. However, the strength and hardness of the steel are relatively high, its formability is very low and adhesion to tool material can be easily found under forming operation. This paper aimed to evaluate the anti-adhesion performance of commercial nitride and DLC films coated on cold work tool steel against HSS in forming operation. The friction coefficient and wear rate of the non-coated ball (SKD11; hardness 60 ± 2 HRC), balls coated with TiN-PVD, TiCN-PVD, AlTiN-PVD, Nitride + CrN and DLC have been evaluated in sliding contact against SPFH 590 (JIS) disk. The scratch and nano-indentation tests were done on each type of coated tools to characterize the adhesive strength between the film and the substrate, and the hardness and the elastic modulus, respectively. The anti-adhesion performance of various films coated tool in metal stamping process was also investigated by performing U-bending experiment. The cold roll carbon steel; SPCC (JIS) was also used to compare a material transfer problem to the case of using HSS (JIS: SPFH590). As the results, for HSS sheet, the adhesion of workpiece material on a non-coated die surface was detected after 49 strokes whereas adhesion could not be found in case of stamping SPCC sheet up to 500 strokes. The TiCN, AlTiN, and Nitride + CrN films showed good anti-adhesion performance when forming HSS, while the TiN and DLC films did not provide the satisfied results.     

Synthesis,characterization and evaluation of titanium carbonitride surface layers with varying concentrations of carbon and nitrogen

Titanium carbonitride (TiCN) surface layers were grown by direct exposure of Ti to a gas mixture of ammonia and methane at 1050 °C. TiC_xN_1?x coatings with varying C/N ratio were synthesized by appropriately changing the content of methane and ammonia in the reactive gas mixture. The resultant layers were subjected to various characterization and evaluation techniques to study the variation of properties with respect to change in C/N ratio. A systematic change in lattice parameter and microstructure was observed as a function of the composition of active gas mixture. Friction coefficient of TiC was found to be extremely low (0.078). Reaction mechanisms for the growth of TiN and TiC were found to be entirely different. The effect of composition of the gas mixture on growth kinetics of TiCN is elucidated.     

In situ nanostructured (TiCr)CN coating by reactive plasma spraying

In situ nanostructured (TiCr)CN composite coating was prepared by reactive plasma spraying Ti-Cr-graphite powder under air atmosphere. The phase composition, microstructure, mechanical properties and wear performance were investigated. The results show that the coating consists of a mixture of TiN, Ti(CN), (TiCr)N, Cr, Ti₃O, and amorphous graphite and CrN phases. The grain size is about 70 nm and the grains present equiaxed and columnar crystal morphologies. Moreover, 5 nm-sized nanocrystals are embedded in an amorphous phase. The (TiCr)CN composite coating possesses high hardness (1325 ± 120 HV) and toughness (4.35 ± 0.53 MPa m^1/2). The friction coefficient and wear rate of the coating are 0.46 and 3.01 ± 0.17 × 10^?6 mm³ N^?1 m^?1, respectively. The inclusion of metallic phase Cr could improve the toughness and wear resistance of the (TiCr)CN coating.     

Substrate effect on wear resistant transition metal nitride hard coatings: Microstructure and tribo-mechanical properties

Four types of different hard transition metal nitrides (TMN:ZrN, CrN, WN and TiN) coatings were deposited on Si (100) and 316LN stainless steel substrates using DC magnetron sputtering. A comprehensive study of microstructure and substrate dependent tribo-mechanical properties of TMN coatings was carried out. Higher hardness (H) and elastic modulus (E) were obtained for WN (H=40 GPa and E=440 GPa) and TiN (H=30 GPa and E=399 GPa) coatings. This is related to the formation of (100) and (111) preferred orientations in WN and TiN coatings, respectively. However, the less hardness and elastic modulus were obtained for ZrN and CrN coatings where (200) orientation is preferred. Remarkably, low friction coefficient (0.06–0.57) and higher wear resistance in the coatings deposited on steel substrates are directly associated with the higher resistance to plastic deformation (H³/E²) and the presence of intrinsic compressive stress. Three body wear modes enhanced the friction coefficient (0.15–0.62) and the wear rate in the coatings deposited on Si substrates. This is primarily associated with low fracture toughness of brittle single crystalline Si (100) substrates. Steel-on-steel contact was dominated in ZrN/steel sliding system. This occurs due to the severe adhesive wear mode of steel ball, whereas, the abrasive wear modes were attained for the CrN, WN and TiN coatings sliding against steel balls.     

Thermal-induced blister cracking behavior of annealed sandwich-structured TiN/CrAlN films

Sandwich-structured TiN/CrAlN films were rationally designed using metallic Ti and Al-Cr alloy targets by RF-pulsed magnetron sputtering. After obtained films were annealed at diverse temperatures at atmospheric pressure for 1 h, the hardness reveals an apparent decrease evolution from 29.2 to 15.7 GPa and H/E* ratio declines below 0.1 with increasing annealing temperature. Meanwhile, the grain size gradually becomes larger from 16.3 to 130.0 nm with increasing annealing temperature. Interestingly, it is observed that cracking behavior of sandwich-structured composite TiN/CrAlN films at elevated temperature is originated from the top of the blisters where main component is alumina on the surface, in virtue of intrinsically induced stress during oxidation, thermal expansion mismatch and phase transformation of the oxide layer. No cracks, nevertheless, are yielded in the film between any two blisters. Herein, these findings provide some beneficial references for preparing high quality films and coatings in high temperature service.     

Synthesis and mechanical properties of carbon nanotube/diamond-like carbon composite films

Diamond-like carbon (DLC) coatings were successfully deposited on carbon nanotube (CNT) films with CNT densities of 1 × 10⁹/cm², 3 × 10⁹/cm², and 7 × 10⁹/cm² by a radio frequency plasma-enhanced chemical vapor deposition (CVD). The new composite films consisting of CNT/DLC were synthesized to improve the mechanical properties of DLC coatings especially for toughness. To compare those of the CNT/DLC composite films, the deposition of a DLC coating on a silicon oxide substrate was also carried out. A dynamic ultra micro hardness tester and a ball-on-disk type friction tester were used to investigate the mechanical properties of the CNT/DLC composite films. A scanning electron microscopic (SEM) image of the indentation region of the CNT/DLC composite film showed a triangle shape of the indenter, however, chippings of the DLC coating were observed in the indentation region. This result suggests the improvement of the toughness of the CNT/DLC composite films. The elastic modulus and dynamic hardness of the CNT/DLC composite films decreased linearly with the increase of their CNT density. Friction coefficients of all the CNT/DLC composite films were close to that of the DLC coating.     

Properties of TiN–Al2O3–TiCN–TiN,TiAlN, and DLC-coated Ti(C,N)-based cermets and their wear behaviors during dry cutting of 7075 aluminum alloys

In the work, TiAlN for physical vapor deposition (PVD), multilayer TiN-Al₂O₃-TiCN-TiN for chemical vapor deposition (CVD), and diamond-like carbon (DLC) for plasma-enhanced chemical vapor deposition (PECVD) were deposited on the cermet inserts. Characteristics and wear behaviors of the three coated cermets during dry cutting of 7075 aluminum alloys were observed. The results show that TiN-Al₂O₃-TiCN-TiN coatings have highest adhesion strength and hardness. At the cutting speed of 1100 r/min, the depth of 0.2 mm, and the feed rate of 0.1 mm/r, the three coated inserts show the best wear-resistant properties. In this case, TiN/Al₂O₃/TiCN/TiN shows the worst wear-resistant properties (value of the flank wear [VBB] = 0.062 mm), while DLC coatings show the most excellent wear-resistant properties (VBB = 0.046 mm). During the cutting of aluminum alloys, which have high plasticity and low melting point, adhesive wear dominate on the flank of the inserts. The thickest coating of TiN/Al₂O₃/TiCN/TiN results in the bluntest cutting edge, which form the most serious adhesive worn zone. For the TiAlN and DLC coatings, due to a smaller cutting force, the two coatings have much better wear resistance. Further, the self-lubricating properties of DLC show excellent effect on protecting the inserts. Thus, the DLC-coated cermets have the best wear-resistant properties. Further, the TiAlN-coated cermets have the widest wear-affected zone while the DLC coating has the narrowest.     

Wear behaviour of hydrogen free diamond-like carbon thin films in diesel fuel at different temperatures

In the present study, super hard, hydrogen free amorphous diamond-like carbons with a high fraction of sp³ hybridised carbon were deposited by pulsed laser deposition. The tribological performance of DLC coatings was investigated by translatory oscillating relative motion of a 100Cr6 steel ball in diesel fuel or ambient air at 25 °C or 150 °C temperature. The structure of the coatings and the tribological worn surfaces were characterised by Raman spectroscopy and by scanning electron microscopy. Bio-fuel with a high fraction of unsaturated fatty acids has the potential to reduce friction in tribological systems with chemically inert DLC. Diesel blend with 10% bio-fuel reduces friction at 150 °C. If there is no diesel fuel, pre-oxidation at 450 °C for 8 h leads to the best wear resistance (↓ f & wear rate) at room temperature. Without diesel fuel, enhancement of temperature up to 150 °C during wear testing causes an increase of the coefficient of friction. Again the 450 °C pre-oxidised sample revealed the lowest friction. For this coating, Raman spectroscopy points to a small increase of the sp² CC bonds. Diesel fuel seems to promote coherent coating failure under 150 °C wear, while pre-oxidation at 450 °C support adhesive coating ablation under higher loads or cyclic loading.     

Atmospheric plasma deposition of diamond-like carbon coatings

The atmospheric pressure plasma-enhanced chemical vapor deposition of diamond-like carbon (DLC) has been investigated. The DLC coatings were grown with a mixture of acetylene, hydrogen and helium that was fed through a linear plasma source. The plasma was driven with radio frequency power at 27.12 MHz. Deposition rates exceeded 0.10 µm/min at substrate temperatures between 155 and 200 °C. Solid-state carbon-13 nuclear magnetic resonance revealed that the coatings contained approximately 43% sp²-bonded carbon and 57% sp³-bonded carbon. Coefficient of friction values for the coatings were found to be 0.24 ± 0.02, which is within the range observed for vacuum deposited DLC.     

Preparation and characterization of Ni–P/nanodiamond coatings: Effects of surfactants

In this study, the effects of different concentrations of surfactants on the properties of the Ni–P/nanodiamond (ND) coatings were investigated. Sodium dodecyl sulfate (SDS) and cetyltrimethyl ammonium bromide (CTAB) were used as the surfactants. Morphology, microhardness and some tribological properties of the coatings were evaluated and compared. Results showed that the composite coatings modified with high concentrations of SDS had smoother surface morphologies than the ones modified with CTAB and low concentrations of SDS. Moreover, it was observed that these coatings had the highest microhardness and wear resistance as well as the lowest friction coefficient (FC) among the coatings. It was found that the effect of NDs on the microhardness of as-plated composite coatings and the ones annealed at 200 °C/3 h was not significant, but became significant when heat treated at 300 °C/1 h and 400 °C/1 h.     

Analysis of instrumented scratch hardness and fracture toughness properties of laser surface alloyed tribological coatings

The mechanical characteristics of ceramic matrix composite (CMC) coatings are widely different from the same materials in bulk form or the individual constituents and are very important to be assessed to carry out application oriented studies on CMC coatings with novel compositions. In the present work, a composite coating of TiB₂, TiN and SiC is fabricated in-situ through a combination of high temperature chemical reaction and laser surface alloying. The formation of the surface layer is due to the laser-assisted chemical reaction followed by laser melting. A mixture of TiO₂, SiO₂, hBN and graphite in stoichiometric proportions is used as the precursor for the chemical reaction. The presence of all the reaction products in the CMC coatings developed is confirmed by X-ray diffraction (XRD) and high resolution transmission electron microscopy (HRTEM). A thorough evaluation of various mechanical properties achieved more insight into the CMC coatings developed. Hardness and fracture toughness of the coatings are measured with a scratch tester. The property evaluations are performed in a similar way for two more coatings fabricated with precursor mixtures containing more than a stoichiometric amount of SiC and hBN respectively. For comparison, a number of composites fabricated through various other routes are characterized afresh with the same set of techniques. Coatings formed with SiC in precursor show higher values of scratch hardness (14.37 GPa), microhardness (24.37 GPa) and fracture toughness (6.63 MPa-m^1/2).     

Prepare SiTiOC ceramic coatings by laser pyrolysis of titanium organosilicon compound

A SiTiOC ceramic coating with outstanding tribological performance was prepared by laser scanning the organosilicon coating with different laser power. The composition and structure of the obtained SiTiOC ceramic coatings were analyzed by scanning electron microscopy (SEM), infrared spectroscopy (FTIR), Raman spectra, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and transmission electron microscope (TEM). The tribological performance of the coatings was studied using a multi-functional reciprocating friction and wear tester. The results showed that the chemical structure (chemical bonding) of the coatings prepared at 0 W, 350 W, and 500 W laser powers included Si-O-Si, Si-C, and TiO₂, while that prepared at 800 W was mainly composed of amorphous SiO₂, indicating that the coating had higher ceramization. The SiTiOC ceramic coatings prepared by the present process effectively reduced the friction coefficient and wear volume of the steel substrate, which indicated that they had good anti-friction and wear resistance properties.     

Hot filament chemical vapour deposition and wear resistance of diamond films on WC-Co substrates coated using PVD-arc deposition technique

Different Cr- and Ti-base films were deposited using PVD-arc deposition onto WC-Co substrates, and multilayered coatings were obtained from the superimposition of diamond coatings, deposited on the PVD interlayer using hot filament chemical vapour deposition (HFCVD). The behaviour of PVD-arc deposited CrN and CrC interlayers between diamond and WC-Co substrates was studied and compared to TiN, TiC, and Ti(C,N) interlayers. Tribological tests with alternative sliding motion were carried out to check the multilayer (PVD + diamond) film adhesion on WC-Co substrate. Multilayer films obtained using PVD arc, characterised by large surface droplets, demonstrated good wear resistance, while diamond deposited on smooth PVD TiN films was not adherent. Multilayered Ti(C,N) + diamond film samples generally showed poor wear resistance.Diamond adhesion on Cr-based PVD coatings deposited on WC-Co substrate was good. In particular, CrN interlayers improved diamond film properties and 6 μm-thick diamond films deposited on CrN showed excellent wear behaviour characterised by the absence of measurable wear volume after sling tests. Good diamond adhesion on Cr-based PVD films has been attributed to chromium carbide formation on PVD film surfaces during the CVD process.     

Effect of Ti particle size on mechanical and tribological properties of TiCN coatings prepared by reactive plasma spraying

Titanium carbonitride (TiCN) coatings were successfully fabricated by reactive plasma spraying (RPS) from agglomerated Ti-graphite feedstock. The effect of Ti particle size on the microstructure and phase composition of plasma sprayed TiCN coatings was investigated. The Vickers microhardness of coatings was measured by a Microhardness Test and the corresponding Weibull distribution were also analyzed. In addition, a pin-on-disk tribometer was employed to determine the trobological properties of coatings. Results show that all the coatings consist of TiC_xN_1−x (0 ≤ x ≤1) and minor Ti₂O phases, and the amount of Ti₂O increases with the increase of Ti particle size. The Weibull distribution of Vickers microhardness of all the coatings shows apparent scattering, while the coating sprayed with Ti particle size of 28 µm exhibits a relatively even distribution. Compared with the coating sprayed with Ti particle size of 14 µm or 48 µm, the coating sprayed with Ti particle size of 28 µm exhibits improved mechanical and tribological properties, which are attributed to the high microhardness and strong bonding strength.     

Influence of countersurface materials on dry sliding performance of CuO/Y-TZP composite at 600 °C

Dry sliding wear tests on 5 wt.% copper oxide doped yttria stabilized zirconia polycrystals (CuO–TZP) composite have been performed against alumina, zirconia and silicon nitride countersurfaces at 600 °C. The influences of load and countersurface materials on the tribological performance of this composite have been studied. The friction and wear test results indicate a low coefficient of friction and specific wear rate for alumina and zirconia countersurfaces at F = 1 N load (maximum Hertzian pressure ～0.5 GPa). Examination of the worn surfaces using scanning electron microscope/energy dispersive spectroscopy confirmed the presence of copper rich layer at the edge of wear scar on the alumina and zirconia countersurfaces. However, Si₃N₄ countersurface sliding against CuO–TZP shows a relatively higher coefficient of friction and higher wear at 1 N load condition. These results suggest that the countersurface material significantly affect the behavior of the third body and self-lubricating ability of the composite.     

Mechanical and high pressure tribological properties of nanocrystalline Ti(N,C) and amorphous C:H nanocomposite coatings

This paper reports on the mechanical and high pressure tribological properties of nanocrystalline (nc-) Ti(N,C)/amorphous (a-) C:H deposited, using low temperature (～ 200 °C) DC reactive magnetron sputtering. The mechanical properties are affected by the nc-Ti(N,C)/a-C:H phase fraction ratio. For increasing C contents (from 31 to 47 at.%) an increase of the a-C:H phase content and a degradation of the nanocrystalline phase occurs leading to a reduction in nanoindentation hardness (H) values (from 15 to 9 GPa) and reduced modulus (Er) values (from 150 to 80 GPa). A strong correlation between H/E ratio and wear performance was exhibited by the coatings. The synthesized coatings survived up to 100 m sliding distance when tested using pin-on-disc sliding configuration at > 4.5 GPa contact pressures and the measured friction coefficient values were similar for all films (μ ～ 0.21–0.25).     

Nano-texture for a wear-resistant and near-frictionless diamond-like carbon

The effect of nano-scale surface texture on wear resistance of diamond-like carbon (DLC) films was studied using a reciprocating ball-on-flat tribometer in dry, humid, and liquid water environments. The nano-scale surface texture was produced by depositing ∼1 μm thick DLC films onto silicon substrates pre-textured with pyramidal wells and polystyrene spheres. The surface roughness of the textured DLC films was about 50 nm in both cases. The friction and wear behavior of the flat and nano-textured DLC films were tested with AISI 440C-grade stainless steel balls at a contact load creating about 360 nm deep Hertzian deformation which is significantly larger than the surface roughness. At this condition, nano-texturing did not affect the friction coefficient, but it significantly reduced the wear of DLC films in dry and humid nitrogen compared to flat DLC. In dry nitrogen, the nano-textured DLC films showed the ultra-low friction without substantial wear of DLC and deposition of thick transfer films onto the counter-surface. The wear reduction appeared to be related to the stress relief in the nano-textured DLC film. In liquid water, surface features on the nano-textured DLC films were diminished due to tribochemical oxidation and material removal at the sliding interface.     

Tribological properties of polymer composites with diamond-like carbon flakes

Composites of epoxy resin with diamond-like carbon (DLC) flakes were fabricated. The DLC flakes were prepared from a DLC film deposited by chemical vapor deposition on an aluminum substrate. The tribological properties of composites were evaluated in air and water environments using a reciprocating friction tester and an AISI 440C mating ball. The friction coefficient of the epoxy composite decreased from 0.90 to 0.69 in air and from 0.71 to 0.29 in water with the addition of DLC flakes. The specific wear rate of the composite also decreased from 5 × 10^? 5 to 7 × 10^? 6 mm³/N m in air and from 4 × 10^? 5 to 4 × 10^? 6 mm³/N m in water. In contrast, the wear of the mating ball increased. Furthermore, the tribological properties of DLC flakes as an additive in water were evaluated. The suspension of powdered DLC in water reduced the friction coefficient of epoxy resin against the AISI 440C mating ball. Furthermore, the wear of the resin was negligibly small, although severe abrasive wear on the mating ball was observed.     

Wear mechanisms of TiN–TiB2 ceramic in sliding against alumina from room temperature to 700 °C

TiN–TiB₂ ceramic was prepared by the reactive hot-pressing method using titanium and BN powders as raw materials. The friction and wear properties of TiN–TiB₂ ceramic were evaluated in sliding against alumina ball from room temperature to 700 °C in air. The TiN–TiB₂ ceramic has a relative density of 98.6%, a flexural strength of 731.9 MPa and a fracture toughness of 8.5 MPa m^1/2 at room temperature. The TiN–TiB₂ ceramic exhibits a distinct decrease in friction coefficient at 700 °C as contrasted with the friction data obtained at room temperature and 400 °C. Wear mechanisms of TiN–TiB₂ ceramic depend mainly upon testing temperature at identical applied loads. Lubricious oxidized products caused by thermal oxidation provide excellent lubrication effects and greatly reduce the friction coefficient of TiN–TiB₂ ceramic at 700 °C. However, abrasive wear and tribo-oxidation are the dominant wear mechanisms of TiN–TiB₂ ceramic at 400 °C. Mechanical polishing effect and removal of micro-fractured grains play important roles during room-temperature wear tests.