In-situ synthesis of reduced graphene oxide wrapped Mn3O4 nanocomposite as anode materials for high-performance lithium-ion batteries

We report a novel in-situ symbiosis method to prepare reduced graphene oxide wrapped Mn₃O₄ nanoparticles (rGO/Mn₃O₄) with uniform size about 50 nm as anodes for lithium-ion batteries (LIBs), which can simplify the preparation process and effectively reduce pollution. The rGO/Mn₃O₄ nanocomposite exhibited a reversible specific capacity of 795.5 mAh g^?1 at 100 mA g^?1 after 200 cycles (capacity retention: 87.4%), which benefits from the unique structural advantages and the synergistic effect of rGO and Mn₃O₄. The Mn₃O₄ nanoparticles encapsulated among the rGO nanosheets exhibited good electrochemical activity, and the multilayer wrinkled rGO sheets provided a stable 3D conduction channel for Li⁺/e^? transport. The rGO/Mn₃O₄ nanocomposite is a promising anode candidate for advanced LIBs with excellent cycling performance and rate performance. Furthermore, this new preparation method can be extended to green and economical synthesis of advanced graphene/manganese-based nanocomposites.     

Rational design of electrochemically active polymorphic MnOx/rGO composites for Li+-rechargeable battery electrodes

Electrochemical behavior of different MnO_x @reduced graphene oxide (rGO) composites derived from a MnO₂/GO template are thoroughly investigated. As-prepared MnO₂/GO mixture is gradually converted to MnO₂/rGO and finally to Mn₃O₄/rGO composites under controlled post annealing conditions. The semispherical Mn₃O₄ crystalline compound anchored composite exhibits stable electrode performances, including both the Li⁺ anode and the Li⁺-air cathode catalyst, induced by the electrochemically favorable composite with an effective large contact area between the active materials and the electronic conductive rGO. It is such a meaningful to suggest the facile and controllable synthetic procedures for obtaining Li-rechargeable electrodes with a MnO_x nanoparticle-incorporated composites for the highly reactive lithiation/delithiation electrochemical reactions.     

Supercapacitor device performances of polycarbazole/graphene and polycarbazole/nanoclay/graphene nanocomposites

In this study, graphene oxide (GO) is chemically reacted with sodium borohydride (NaBH₄) to form reduced graphene oxide (rGO). rGO, polycarbazole (PCz)/rGO and PCz/nanoclay/rGO materials were obtained by chemical polymerisation method. These three materials were characterised by Fourier-transform infra-red spectroscopy-attenuated transmission reflectance, scanning electron microscopy, energy-dispersive X-ray analysis, cyclic voltammetry (CV), galvanostatic charge–discharge and electrochemical impedance spectroscopy. The PCz/nanoclay/rGO nanocomposite shows significantly improved capacitance (C_sp?=?187.78?F?g^?1) compared to that of PCz/rGO (C_sp?=?74.18?F?g^?1) and rGO (C_sp?=?20.78?F?g^?1) at the scan rate of 10?mV?s^?1 by CV method. The supercapacitor device performance results show high power density (P?=?1057.81?W?kg^?1) and energy density (E?=?1.7?Wh?kg^?1) obtained from Ragone plot for PCz/nanoclay/rGO material. Stability tests were also examined by the CV method for 1000 cycles.     

A nanocomposite of graphene/MnO2 nanoplatelets for high-capacity lithium storage

A nanocomposite of graphene/MnO₂ nanoplatelets was prepared by one-step chemistry route at room temperature. The microstructure was characterized by X-ray diffraction, N₂ absorption, scanning electron microscopy (SEM), and transmission electron microscopy (TEM). Both TEM and SEM images show that MnO₂ nanoplatelets are homogeneously distributed on the graphene nanosheets. The electrochemical properties were tested by cyclic voltammetry, galvanostatic charge–discharge experiments. The nanocomposite exhibited high lithium capacity (905?mAh?g^?1 at 100?mA?g^?1). The superior lithium storage capability can be attributed to the “open” structure: the large effective surface area and short diffusion paths.     

High-performance supercapacitor of manganese oxide/reduced graphene oxide nanocomposite coated on flexible carbon fiber paper

Although supercapacitors have higher power density than batteries, they are still limited by low energy density and low capacity retention. Here we report a high-performance supercapacitor electrode of manganese oxide/reduced graphene oxide nanocomposite coated on flexible carbon fiber paper (MnO₂–rGO/CFP). MnO₂–rGO nanocomposite was produced using a colloidal mixing of rGO nanosheets and 1.8 ± 0.2 nm MnO₂ nanoparticles. MnO₂–rGO nanocomposite was coated on CFP using a spray-coating technique. MnO₂–rGO/CFP exhibited ultrahigh specific capacitance and stability. The specific capacitance of MnO₂–rGO/CFP determined by a galvanostatic charge–discharge method at 0.1 A g⁻¹ is about 393 F g⁻¹, which is 1.6-, 2.2-, 2.5-, and 7.4-fold higher than those of MnO₂–GO/CFP, MnO₂/CFP, rGO/CFP, and GO/CFP, respectively. The capacity retention of MnO₂–rGO/CFP is over 98.5% of the original capacitance after 2000 cycles. This electrode has comparatively 6%, 11%, 13%, and 18% higher stability than MnO₂–GO/CFP, MnO₂/CFP, rGO/CFP, and GO/CFP, respectively. It is believed that the ultrahigh performance of MnO₂–rGO/CFP is possibly due to high conductivity of rGO, high active surface area of tiny MnO₂, and high porosity between each MnO₂–rGO nanosheet coated on porous CFP. An as-fabricated all-solid-state prototype MnO₂–rGO/CFP supercapacitor (2 × 14 cm) can spin up a 3 V motor for about 6 min.     

Room temperature in situ chemical synthesis of Fe3O4/graphene

A simple, cost-effective, efficient, and green approach to synthesize iron oxide/graphene (Fe₃O₄/rGO) nanocomposite using in situ deposition of Fe₃O₄ nanoparticles on reduced graphene oxide (rGO) sheets is reported. In the redox reaction, the oxidation state of iron(II) is increased to iron(III) while the graphene oxide (GO) is reduced to rGO. The GO peak is not observed in the X-ray diffraction (XRD) pattern of the nanocomposite, thus providing evidence for the reduction of the GO. The XRD spectra do have peaks that can be attributed to cubic Fe₃O_4. The field emission scanning electron microscopy (FESEM) images show Fe₃O₄ nanoparticles uniformly decorating rGO sheets. At a low concentration of Fe²⁺, there is a significant increase in the intensity of the FESEM images of the resulting rGO sheets. Elemental mapping using energy dispersive X-ray (EDX) analysis shows that these areas have a significant Fe concentration, but no morphological structure could be identified in the image. When the concentration of Fe²⁺ is increased, the Fe₃O₄ nanoparticles are formed on the rGO sheets. Separation of the Fe₃O₄/rGO nanocomposite from the solution could be achieved by applying an external magnetic field, thus demonstrating the magnetic properties of the nanocomposite. The Fe₃O₄ particle size, magnetic properties, and dispersibility of the nanocomposite could be altered by adjusting the weight ratio of GO to Fe²⁺ in the starting material.     

Mn3O4 nanoparticles embedded into graphene nanosheets: Preparation, characterization, and electrochemical properties for supercapacitors

Mn₃O₄/graphene nanocomposites were synthesized by mixing graphene suspension in ethylene glycol with MnO₂ organosol, followed by subsequent ultrasonication processing and heat treatment. The as-prepared product consists of nanosized Mn₃O₄ particles homogeneously distributed on graphene nanosheets, which has been confirmed by field emission scanning electron microscopy and transmission electron microscopy analysis. Atomic force microscope analysis further identified the distribution of dense Mn₃O₄ nanoparticles on graphene nanosheets. When used as electrode materials in supercapacitors, Mn₃O₄/graphene nanocomposites exhibited a high specific capacitance of 175 F g⁻¹ in 1 M Na₂SO₄ electrolyte and 256 F g⁻¹ in 6 M KOH electrolyte, respectively. The enhanced supercapacitance of Mn₃O₄/graphene nanocomposites could be ascribed to both electrochemical contributions of Mn₃O₄ nanoparticles, functional groups attached to graphene nanosheets, and significantly increased specific surface area.     

V2O3/rGO composite as a potential anode material for lithium ion batteries

V₂O₃ is a promising anode material and has attracted the interests of researchers because of its high theoretical capacity of 1070?mAh?g^?1, low discharge potential, inexpensiveness, abundant sources, and environmental friendliness. However, the development and application of V₂O₃ have been hindered by the low conductivity and drastic volume change of V₂O₃ composites. In this work, V₂O₃/reduced graphene oxide (rGO) nanocomposites are successfully prepared through a facile solvothermal method and annealing process. In this synthesis protocol, V₂O₃ nanoparticles (NPs) are encapsulated by rGO. This unique structure enables rGO to inhibit volume changes and improve the ion and electronic conductivity of V₂O₃. In addition, V₂O₃ NPs, which exhibit sizes of 5–40?nm, are uniformly dispersed on rGO sheets without aggregation. The Li⁺ storage behavior of V₂O₃/rGO is systematically investigated in the potential range 0.01–3.0?V. The V₂O₃/rGO nanocomposite can achieve a high reversible specific capacity of 823.4?mAh?g^?1 under the current density of 0.1?A?g^?1, and 407.3 mAh g^?1 under the high current density of 4.0?A?g^?1. The results of this study provide insight into the fabrication of rGO-based functional materials with extensive applications.     

Vertically aligned,polypyrrole encapsulated MoS2/graphene composites for high-rate LIBs anode

Ultrathin MoS₂ nanosheets were vertically anchored on the reduced graphene oxide (MoS₂/rGO) via hydrothermal method. To further engineering the surface conductivity, ultrathin polypyrrol (PPy) layer was coated on the MoS₂/rGO composite via in situ polymerization to form a bi-continuous conductive network with a sandwich-like structure. The graphene nanosheets and the PPy coating can facilitate the electrons transfer rate, while the ultrathin MoS₂ nanosheets can enhance the utilization efficiency of the active materials. The obtained MoS₂/rGO-10 composite exhibits high reversible specific capacity (970?mAh?g^?1 at 0.1?A?g^?1) and rate capability (capacity retention of 64% at 3.2?A?g^?1). Moreover, the PPy@MoS₂/rGO hybrids reveal lower specific capacity but better rate capability, and a “trade-off” effect between electrons and ions transfer resistance was observed. This easy-scalable PPy surface conductivity engineering strategy may be applied in the preparation of high-performance LIBs active materials.     

Hydrothermal synthesis of reduced graphene oxide-Mn3O4 nanocomposite as an efficient electrode materials for supercapacitors

Mn₃O₄ nanoparticles (NPs) are decorated with reduced graphene oxide nanosheets (rGO-Mn₃O₄) through a facile and eco-friendly hydrothermal method. The as-synthesized composite was characterized by XRD, SEM, TEM and Raman spectroscopy. The electrochemical properties of (rGO-Mn₃O₄) nanocomposite were studied as electrode materials for supercapacitors. The rGO-Mn₃O₄ nanocomposite exhibit high specific capacitance of 457 Fg^?1 at 1.0 A/g in 1 M Na₂SO₄ aqueous electrolyte. The rGO-Mn₃O₄ exhibits good capacitance retention by achieving 91.6% of its initial capacitance after 5000 cycles. The excellent electrochemical performance is attributed to the increased electrode conductivity in the presence of graphene network.     

Wrapping mesoporous Fe2O3 nanoparticles by reduced graphene oxide: Enhancement of cycling stability and capacity of lithium ion batteries by mesoscopic engineering

The fast capacity fading at high current density turns out to be one of the key challenges limiting the broad applications of transition metal oxide-based electrodes. Herein, Fe₂O₃ nanoparticles with well-defined mesopores wrapped by reduced graphene oxide (RGO) have been synthesized via a facile hydrothermal strategy. The as-prepared nanocomposites were systematically characterized. XPS and Raman analyses confirm the co-existence of Fe₂O₃ and RGO in the nanocomposite system. SEM and TEM reveal that the mesoporous Fe₂O₃ nanoparticles have a size of 20–60?nm and are uniformly dispersed and tightly wrapped by RGO. When used as the anode in lithium ion batteries, the mesoporous-Fe₂O₃/RGO electrode exhibits excellent cycling stability (1098?mA?h?g^?1 after 500 cycles at 1?A?g^?1) and superior rate capability (574?mA?h?g^?1 at 5?A?g^?1). The excellent electrochemical performance can be mainly ascribed to the unique mesoscopic architecture that serves as a cushion to alleviate volume change of Fe₂O₃ during discharge/charge cycles, provides a sustainably large contact area with the electrolyte, and improves electrical conductivity. This unique nanocomposite electrode holds great potential as an anode material for advanced lithium ion batteries.     

Synthesis of rGO/nanoclay/PVK nanocomposites,electrochemical performances of supercapacitors

ABSTRACT

In this study, graphene oxide (GO) was chemically reacted with sodium borohydride (NaBH₄) to form reduced graphene oxide (rGO). rGO, Montmorillonite nanoclay, and polyvinylcarbazole (PVK) were used to form a ternary nanocomposite via chemical reaction. These nanocomposite qualities were described via scanning electron microscopy (SEM), energy-dispersive X-ray analysis (EDX), Fourier transform infrared spectroscopy-attenuated transmission reflectance (FTIR-ATR). In addition, these materials were used in supercapacitor device as an active material to test electrochemical performances via cyclic voltammetry (CV), galvanostatic charge–discharge (GCD), and electrochemical impedance spectroscopy (EIS). The rGO/nanoclay/PVK nanocomposite shows significantly improved specific capacitance (C_sp = 168.64 Fg^?1) compared to that of rGO (C_sp = 63.26 Fg^?1) at the scan rate of 10 mVs^?1 by CV method. The enhanced capacitance results in high power density (P = 5522.6 Wkg^?1) and energy density (E = 28.84 Whkg^?1) capabilities of the rGO/nanoclay/PVK nanocomposite material. The addition of nanoclay and PVK increased the specific capacitance of rGO material due to a dopant effect for supercapacitor studies. Ragone plots were drawn to observe energy and power density of supercapacitor devices. The C_sp of rGO/nanoclay/PVK nanocomposite has only 86.4% of initial capacitance for charge/discharge performances obtained by CV method for 5000 cycles.     

Microwave-assisted one-pot synthesis of SnC2O4/graphene composite anode material for lithium-ion batteries

Currently, SnC₂O₄ is considered as one of the most promising anode materials for high-energy lithium-ion batteries (LIBs) because its charge capacity is higher than that of metal oxides. Herein, a facile microwave-assisted solvothermal method was employed to obtain SnC₂O₄/GO composites within only 30?min, which is time-efficient. The amount of SnC₂O₄ was increased to 95.3?wt% to improve the capacity of the composite. Pure SnC₂O₄ with a high specific surface area of 19.6?m² g^?1 without any other tin compound was used for fabrication. The SnC₂O₄/GO composite exhibited excellent electrochemical performance, with reversible discharge/charge capacity of 657/659?mA?h?g^?1 after 100 cycles at 0.2?A?g^?1. Furthermore, at high current densities of 1.0 and 2.0?A?g^?1, the SnC₂O₄/GO composite anode exhibited high reversible discharge/charge capacities of 553/552 and 418/414?mA?h?g^?1, respectively, after 200 cycles at room temperature. These improvements were likely obtained because SnC₂O₄ was well composited with graphene, which not only offered rapid electron transfer but also released the tension produced by the volumetric effect during repeated lithiation/delithiation. Cyclic voltammetry (CV) was also performed to further study the electrochemical reactions of SnC₂O₄/GO. The facile microwave-assisted solvothermal method used herein is considered as a highly efficient method to fabricate metal oxalate/graphene composites for use as anode materials in LIBs.     

Synthesis of graphene/α-Fe2O3 nanospindles by hydrothermal assembly and their lithium storage performance

Nanocomposite of graphene/α-Fe₂O₃ (G/α-Fe₂O₃) nanospindles was synthesized by a simple hydrothermal assembly method followed by thermal treatment. The α-Fe₂O₃ nanospindles were evenly enwrapped by the graphene nanosheets. When evaluated as an anode for Li-ion batteries (LIBs), the G/α-Fe₂O₃ nanocomposite showed enhanced cycling performance and rate capability compared to pure α-Fe₂O₃. G/α-Fe₂O₃ retained a reversible capacity of 607 mAh g^?1 after 100 cycles at 100 mA g^?1-, which is far higher than that (160 mAh g^?1) of α-Fe₂O₃. The superior electrochemical performance of G/α-Fe₂O₃ can be attributed to the protection effect of graphene nanosheets to accommodate the volume change of α-Fe₂O₃ during lithiation/delithiation.     

Achieving ultra-high electromagnetic wave absorption by anchoring Co0.33Ni0.33Mn0.33Fe2O4 nanoparticles on graphene sheets using microwave-assisted polyol method

The Co_0.33Ni_0.33Mn_0.33Fe₂O₄/graphene nanocomposite for electromagnetic wave absorption was successfully synthesized from metal chlorides solutions and graphite powder by a simple and rapid microwave-assisted polyol method via anchoring the Co_0.33Ni_0.33Mn_0.33Fe₂O₄ nanoparticles on the layered graphene sheets. The Fe³⁺, Co²⁺, Ni²⁺ and Mn²⁺ ions in the solutions were attracted by graphene oxide obtained from graphite and converted to the precursors Fe(OH)₃, Co(OH)₂, Ni(OH)₂, and Mn(OH)₂ under slightly alkaline conditions. After the transformations of the precursors to Co-Ni-Mn ferrites and conversion of graphene oxide to graphene under microwave irradiation at 170?°C in just 25?min, the Co_0.33Ni_0.33Mn_0.33Fe₂O₄/graphene nanocomposite was prepared. The composition and structure of the nanocomposite were characterized by X-ray diffraction (XRD), inductive coupled plasma emission spectroscopy (ICP), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FT-IR), Raman spectroscopy (RS), transmission electron microscopy (TEM), etc. It was found that with the filling ratio of only 20?wt% and the thickness of 2.3?mm, the nanocomposite showed an ultra-wide effective absorption bandwidth (less than ?10?dB) of 8.48?GHz (from 9.52 to 18.00?GHz) with the minimum reflection loss of ??24.29?dB. Compared to pure graphene sheets, Co_0.33Ni_0.33Mn_0.33Fe₂O₄ nanoparticles and the counterparts reported in literature, the nanocomposite exhibited much better electromagnetic wave absorption, mainly attributed to strong wave attenuation, as a result of synergistic effects of dielectric loss, conductive loss and magnetic loss, and to good impedance matching. In view of its thin thickness, light weight and outstanding electromagnetic wave absorption property, the nanocomposite could be used as a very promising electromagnetic wave absorber.     

Li0.95Na0.05MnPO4/C nanoparticles compounded with reduced graphene oxide sheets for superior lithium ion battery cathode performance

Sodium-substituted LiMnPO₄/C/reduced graphene oxide (LNMP@rGO) was synthesized in this study via freeze drying and carbon thermal reduction method with graphene oxide as carbon source. Sodium ion doping is optimized and rGO effects are evaluated by XRD, SEM, TEM, BET, Raman, and electrochemical performance measurements. Well-distributed nanoparticles with average size of ~50?nm are evenly distributed on the surface or intercalation between rGO layers, resulting in a porous ion/electronic conductive network. Compared to 122.3?mA?h?g^?1 in unmodified LNMP, the best LNMP@rGO (20?mg rGO) exhibits an excellent initial discharge capacity of 150.4?mA?h?g^?1 at 0.05?C at 122.9% of the initial capacity. The capacity retention rate is 95.8% of the initial capacity after 100 cycles at 1?C. Capacity of 101.2?mA?h?g^?1 is preserved even at rates as high as 10?C.     

Enhancing electrochemical performance of Fe3O4/graphene hybrid aerogel with hydrophilic polymer

Graphene hybrid aerogels have attracted attention as electrode materials because of their unique porous architectures. However, their electrochemical performance is limited by the intrinsic hydrophobicity and the ease of aggregation of graphene nanosheets. We demonstrate a unique methodology to produce graphene hybrid aerogels through assembly of graphene nanosheets, nanometer‐scale ferroferric oxide (Fe₃O₄), and hydrophilic poly(vinyl alcohol) (PVA) into three‐dimensional hierarchical macrostructures. Electrochemical performance measurements exhibit a significant improvement in the specific capacitance of this ternary hybrid aerogel with remarkable cycling stability. Specifically, the specific capacitance is nearly 6.6 times higher than that of the neat graphene aerogel, and a cycling capacitance retention rate of 99% was achieved after 2000 cycles at a high current density of 0.5 A g^?1. Electrochemical impedance spectroscopy measurements demonstrate a lower resistance in the Fe₃O₄/graphene/PVA aerogel electrode compared with that of both neat graphene and Fe₃O₄/graphene aerogel electrodes. The obtained graphene hybrid aerogels with outstanding cycling performance and high energy density are very promising as electrode materials for supercapacitors. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 45566.     

Conversion of pencil graphite to graphene/polypyrrole nanofiber composite electrodes and its doping effect on the supercapacitive properties

Graphene platelets were synthesized from pencil flake graphite and commercial graphite by chemical method. The chemical method involved modified Hummer's method to synthesize graphene oxide (GO) and the use of hydrazine monohydrate to reduce GO to reduced graphene oxide (rGO). rGO were further reduced using rapid microwave treatment in presence of little amount of hydrazine monohydrate to graphene platelets. Chemically modified graphene/polypyrrole (PPy) nanofiber composites were prepared by in situ anodic electropolymerization of pyrrole monomer in the presence of graphene on stainless steel substrate. The morphology, composition, and electronic structure of the composites together with PPy fibers, graphene oxide (GO), rGO, and graphene were characterized using X‐ray diffraction (XRD), laser‐Raman, and scanning electron microscopic (SEM) methods. From SEM, it was observed that chemically modified graphene formed as a uniform nanocomposite with the PPy fibers absorbed on the graphene surface and/or filled between the graphene sheets. Such uniform structure together with the observed high conductivities afforded high specific capacitance and good cycling stability during the charge–discharge process when used as supercapacitor electrodes. A specific capacitance of supercapacitor was as high as 304 F g^?1 at a current density of 2 mA cm^?1 was achieved over a PPy‐doped graphene composite. POLYM. ENG. SCI., 55:2118–2126, 2015. © 2014 Society of Plastics Engineers     

Synthesis and electrochemical properties of graphene oxide/nanosulfur/polypyrrole ternary nanocomposite hydrogel for supercapacitors

A method for synthesizing Graphene oxide (GO)/nano‐sulfur/polypyrrole (PPy) ternary nanocomposite hydrogel is depicted. The higher surface area of GO, PPy porous structure and their excellent conductivity are utilized, and the GO hydrogel can be made easily. The products are characterized by field‐emission scanning electron microscopy (FESEM), X‐ray diffraction (XRD), Fourier transform infrared (FTIR) spectra, and electrochemical workstation. The results demonstrated that GO/nano‐S/PPy ternary nanocomposite hydrogel is successfully synthesized. The electrochemical properties are investigated by cyclic voltammetry, galvanostatic charge/discharge measurements, and cycling life in a three‐electrode system in 1M Li₂SO₄ electrolyte solution. The GO/nano‐S/PPy ternary nanocomposite hydrogel exhibit a high specific capacitance of 892.5 F g^?1 at scan rates of 5 mV s^?1 and the capacitance retain about 81.2% (594.8 F g^?1) of initial capacitance (732.5 F g^?1) after 500 cycles at a current density of 1 A g^?1. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40814.     

In situ sonochemical synthesis of Fe3O4–graphene nanocomposite for lithium rechargeable batteries

In this paper, we have presented experimental results for preparation of Fe₃O₄–graphene nanocomposite that uses an ultrasound assisted method. The graphene oxide (GO) was prepared from graphite powder using modified Hummers–Offeman method. Subsequently, the synthesis of graphene-Fe₃O₄ nanocomposite was carried out by ultrasound assisted co-precipitation of iron (II) and (III) chlorides in the presence of GO. The formation of GO and graphene-Fe₃O₄ nanocomposite was confirmed by X-ray diffraction (XRD), Energy dispersive X-ray (EDX) analysis and Fourier transform-infrared (FTIR) analysis. The particle size of Fe₃O₄ nanoparticles loaded on graphene nanosheets (observed from TEM image) was found to be smaller than 20 nm. The use of ultrasonic irradiations during synthesis of graphene-Fe₃O₄ nanocomposite resulted in uniform loading of Fe₃O₄ nanoparticles on graphene nanosheets. The prepared graphene-Fe₃O₄ nanocomposite material was used for the preparation of anode for lithium ion batteries. The electrochemical performance of the material was tested by cyclic voltammetry (CV) and charge/discharge cycles. It was observed that the capacity of Li-battery when the anode material was made using graphene-Fe₃O₄ nanocomposite showed stable electrochemical performance for around 120 cycles and the battery could repeat stable charge–discharge reaction.