Optimal synthesis and new understanding of P2-type Na2/3Mn1/2Fe1/4Co1/4O2 as an advanced cathode material in sodium-ion batteries with improved cycle stability

A sol-gel method with ethylene diamine tetraacetic acid and citric acid as co-chelates is employed for the synthesis of P2-type Na_2/3Mn_1/2Fe_1/4Co_1/4O₂ as cathode material for sodium-ion batteries. Among the various calcination temperatures, the Na_2/3Mn_1/2Fe_1/4Co_1/4O₂ with a pure P2-type phase calcined at 900 °C demonstrates the best cycle capacity, with a first discharge capacity of 157 mA h g^?1 and a capacity retention of 91 mA h g^?1 after 100 cycles. For comparison, the classic P2-type Na_2/3Mn_1/2Fe_1/2O₂ cathode prepared under the same conditions shows a comparable first discharge capacity of 150 mA h g^?1 but poorer cycling stability, with a capacity retention of only 42 mA h g^?1 after 100 cycles. Based on X-ray photoelectron spectroscopy, the introduction of cobalt together with sol-gel synthesis solves the severe capacity decay problem of P2-type Na_2/3Mn_1/2Fe_1/2O₂ by reducing the content of Mn and slowing down the loss of Mn on the surface of the Na_2/3Mn_1/2Fe_1/4Co_1/4O₂, as well as by improving the activity of Fe³⁺ and the stability of Fe⁴⁺ in the electrode. This research is the first to demonstrate the origin of the excellent cycle stability of Na_2/3Mn_1/2Fe_1/4Co_1/4O₂, which may provide a new strategy for the development of electrode materials for use in sodium-ion batteries.     

Facile synthesis and electrochemical performance of nitrogen-doped porous hollow coaxial carbon fiber/Co3O4 composite

Economy and efficiency are two important indexes of lithium-ion batteries (LIBs) materials. In this work, nitrogen doped hollow porous coaxial carbon fiber/Co₃O₄ composite (N-PHCCF/Co₃O₄) is fabricated using the fibers of waste bamboo leaves as the template and carbon resource by soaking and thermal treatment, respectively. The N-PHCCF/Co₃O₄ exhibits an outstanding electrochemical performance as anode material for lithium ion batteries, due to the nitrogen doping, coaxial configuration and porous structure. Specifically, it delivers a high discharge reversible specific capacity of 887 mA h g^?1 after 100 cycles at the current density of 100 mA g^?1. Furthermore a high capability of 415 mA h g^?1 even at 1 A g^?1 is exhibited. Most impressively, the whole process is facile and scalable，exhibiting recycling of resource and turning waste into treasure in an eco-friendly way.     

Towards high purity graphene/single-walled carbon nanotube hybrids with improved electrochemical capacitive performance

CoMgAl layered double hydroxides were prepared as catalysts for the in situ synchronous growth of graphene and single-walled carbon nanotubes (SWCNTs) from methane by chemical vapor deposition. The as-calcined CoMgAl layered double oxide (LDO) flakes served as the template for the deposition of graphene, and Co nanoparticles (NPs) embedded on the LDOs catalyzed the growth of SWCNTs. After the removal of CoMgAl LDO flakes, graphene (G)/SWCNT/Co₃O₄ hybrids with SWCNTs directly grown on the surface of graphene and 27.3 wt.% Co₃O₄ NPs encapsulated in graphene layers were available. Further removal of the Co₃O₄ NPs by a CO₂-oxidation assistant purification method induced the formation of G/SWCNT hybrids with a high carbon purity of 98.4 wt.% and a high specific surface area of 807.0 m²/g. The G/SWCNT/Co₃O₄ hybrids exhibited good electrochemical performance for pseudo-capacitors due to their high Co₃O₄ concentration and the high electrical conductivity of SWCNTs and graphene. In another aspect, the G/SWCNT hybrids can be used as excellent electrode materials for double-layer capacitors. A high capacity of 98.5 F/g_electrode was obtained at a scan rate of 10 mV/s, 78.2% of which was retained even when the scan rate increased to 500 mV/s.     

Hydrothermal synthesis of reduced graphene oxide-Mn3O4 nanocomposite as an efficient electrode materials for supercapacitors

Mn₃O₄ nanoparticles (NPs) are decorated with reduced graphene oxide nanosheets (rGO-Mn₃O₄) through a facile and eco-friendly hydrothermal method. The as-synthesized composite was characterized by XRD, SEM, TEM and Raman spectroscopy. The electrochemical properties of (rGO-Mn₃O₄) nanocomposite were studied as electrode materials for supercapacitors. The rGO-Mn₃O₄ nanocomposite exhibit high specific capacitance of 457 Fg^?1 at 1.0 A/g in 1 M Na₂SO₄ aqueous electrolyte. The rGO-Mn₃O₄ exhibits good capacitance retention by achieving 91.6% of its initial capacitance after 5000 cycles. The excellent electrochemical performance is attributed to the increased electrode conductivity in the presence of graphene network.     

Evaluation of supercapacitive and magnetic properties of Fe3O4 nano-particles electrochemically doped with dysprosium cations: Development of a novel iron-based electrode

In this research, a novel one-pot fabrication platform was developed for the preparation of Dy³⁺-doped iron oxide nanoparticles (Dy-IONPs). In the procedure, Dy-IONPs are electro-deposited from an additive-free aqueous mixed solution of iron(III) nitrate, iron(II) chloride and dysprosium chloride salts through applying a current density of 10 mA cm^–2 for 30 min. The analytical data obtained from X-ray diffraction (XRD), field emission electron microscopy (FE-SEM) and energy-dispersive X-ray (EDX) confirmed the deposited Dy-IONPs to be composed of magnetite nanoparticles (size≈20 nm) containing about 10 wt% of Dy³⁺ cations as the doping agent. The electrochemical data obtained through galvanostatic charge-discharge (GCD) tests showed that Dy-IONPs provide specific capacitances values of as high as 202 and 111 F g^?1at the discharge loads of 0.5 and 5 A g^?1, respectively, and reveal capacity retentions of 93.9% and 77.2% after 2000 GCD cycling. These could be held as proof that the electro-synthesized Dy³⁺-doped Fe₃O₄ NPs are suitable candidates for use in supercapacitors. Furthermore, the results of vibrating sample magnetometer (VSM) measurements indicated better superparamagnetic behavior of the Dy-IONPs (Mr = 0.34 emu g^–1 and H_Ci= 6.25 G) as opposed to pure IONPs (Mr = 0.95 emu g^–1 and H_Ci= 14.62 G), which originates from their lower Mr and Hci values. Based on the results, the proposed electro-synthesis method offers a facile procedure for the preparation of high- performance metal-ion-doped IONPs.     

Studies on spinel cobaltites,MCo2O4 (M = Mn,Zn, Fe,Ni and Co) and their functional properties

Optimization of electrodes for charge storage with appropriate processing conditions places significant challenges in the developments for high performance charge storage devices. In this article, metal cobaltite spinels of formula MCo₂O₄ (where M = Mn, Zn, Fe, Ni and Co) are synthesized by oxalate decomposition method followed by calcination at three typical temperatures, viz. 350, 550, and 750 °C and examined their performance variation when used as anodes in lithium ion batteries. Phase and structure of the materials are studied by powder x-ray diffraction (XRD) technique. Single phase MnCo2O4,ZnCo2O4 and Co3O4 are obtained for all different temperatures 350 °C, 550 °C and 750 °C; whereas FeCo₂O₄ and NiCo₂O₄ contained their constituent binary phases even after repeated calcination. Morphologies of the materials are studied via scanning electron microscopy (SEM): needle-shaped particles of MnCo₂O₄ and ZnCo₂O₄, submicron sized particles of FeCo₂O₄ and agglomerated submicron particle of NiCo₂O₄ are observed. Galvanostatic cycling has been conducted in the voltage range 0.005–3.0 V vs. Li at a current density of 60 mA g^?1 up to 50 cycles to study their Li storage capabilities. Highest observed charge capacities are: MnCo₂O₄ – 365 mA h g^?1 (750 °C); ZnCo₂O₄ – 516 mA h g^?1 (550 °C); FeCo₂O₄ – 480 mA h g^?1 (550 °C); NiCo₂O₄ – 384 mA h g^?1 (750 °C); and Co₃O₄ – 675 mA h g^?1 (350 °C). The Co₃O₄ showed the highest reversible capacity of 675 mA h g^?1; the NiO present in NiCo₂O₄ acts as a buffer layer that results in improved cycling stability; the ZnCo₂O₄ with long needle-like shows good cycling stability.     

Cobalt oxide nanocubes as electrode material for the performance evaluation of electrochemical supercapacitor

Porous cobalt oxide (Co₃O₄) nanocubes (NCs) were synthesized by a simple and cost-effective hydrothermal technique for the potential application of electrochemical supercapacitors. The hydrothermally synthesized materials exhibited the small cube like morphology with the average size of ~ 50 to 60 nm. The surface analysis revealed a good surface area, and high pore volume of the synthesized porous Co₃O₄ NCs. The capacitive properties of porous Co₃O₄ NCs electrode were investigated by cyclic voltammetry (CV) in 6 M KOH electrolyte and a high specific capacitance of ~ 430.6 F/g at a scan rate of ~ 10 mV s^?1 was observed. The capacity retention of up to ~ 85% after 1000 cycles was shown by the fabricated porous Co₃O₄ NCs electrode. The porous Co₃O₄ NCs showed excellent structural stability through cycling with promising capacity retention which suggested a good quality of porous Co₃O₄ NCs as electrochemical supercapacitor electrode.     

Synthesis of graphene/α-Fe2O3 nanospindles by hydrothermal assembly and their lithium storage performance

Nanocomposite of graphene/α-Fe₂O₃ (G/α-Fe₂O₃) nanospindles was synthesized by a simple hydrothermal assembly method followed by thermal treatment. The α-Fe₂O₃ nanospindles were evenly enwrapped by the graphene nanosheets. When evaluated as an anode for Li-ion batteries (LIBs), the G/α-Fe₂O₃ nanocomposite showed enhanced cycling performance and rate capability compared to pure α-Fe₂O₃. G/α-Fe₂O₃ retained a reversible capacity of 607 mAh g^?1 after 100 cycles at 100 mA g^?1-, which is far higher than that (160 mAh g^?1) of α-Fe₂O₃. The superior electrochemical performance of G/α-Fe₂O₃ can be attributed to the protection effect of graphene nanosheets to accommodate the volume change of α-Fe₂O₃ during lithiation/delithiation.     

Hydrazine hydrate-induced hydrothermal synthesis of MnFe2O4 nanoparticles dispersed on graphene as high-performance anode material for lithium ion batteries

Herein, a MnFe₂O₄/graphene (MnFe₂O₄/G) nanocomposite has been synthesized via a facile N₂H₄·H₂O-induced hydrothermal method. During the synthesis, N₂H₄·H₂O is employed to not only reduce graphene oxide to graphene, but also prevent the oxidation of Mn²⁺ in alkaline aqueous solution, thus ensuring the formation of MnFe₂O₄/G. Moreover, MnFe₂O₄ nanoparticles (5–20 nm) are uniformly anchored on graphene. MnFe₂O₄/G electrode delivers a large reversible capacity of 768 mA h g⁻¹ at 1 A g⁻¹ after 200 cycles and high rate capability of 517 mA h g⁻¹ at 5 A g⁻¹. MnFe₂O₄/G holds great promise as anode material in practical applications due to the outstanding electrochemical performance combined with the facile synthesis strategy.     

Preparation of scale-like nickel cobaltite nanosheets assembled on nitrogen-doped reduced graphene oxide for high-performance supercapacitors

Ultrathin scale-like nickel cobaltite (NiCo₂O₄) nanosheets supported on nitrogen-doped reduced graphene oxide (N-rGO) are successfully synthesized through a facile co-precipitation of Ni²⁺ and Co²⁺ in the presence of sodium citrate and hexamethylenetetramine and subsequent calcination treatment. The composition and morphology of NiCo₂O₄ nanosheets@nitrogen-doped reduced graphene oxide (denoted as NiCo₂O₄ NSs@N-rGO) were characterized by Scanning electron microscope, Transmission electron microscope, X-ray diffraction, Raman spectra, X-ray photoelectron spectroscopy, Brunauer–Emmett–Teller and thermogravimetric analysis. The thickness of NiCo₂O₄ nanosheets anchored on the reduced graphene oxide is around 4 nm. The capacitance of NiCo₂O₄ NSs@N-rGO is evaluated by cyclic voltammogram and galvanostatic charge/discharge with the result that the NiCo₂O₄ NSs@N-rGO could deliver a specific capacitance of 1540 F g⁻¹ after 1000 cycles at 10 A g⁻¹.     

Honeycomb-like NiCo2O4@Ni(OH)2 supported on 3D N−doped graphene/carbon nanotubes sponge as an high performance electrode for Supercapacitor

In order to increase the energy density of supercapacitor, a new kind electrode material with excellent structure and outstanding electrochemical performance is highly desired. In this article, a new type of three-dimensional (3D) nitrogen-doped single-wall carbon nanotubes (SWNTs)/graphene elastic sponge (TRGN?CNTs?S) with low density of 0.8 mg cm^?3 has been successfully prepared by pyrolyzing SWNTs and GO coated commercial polyurethane (PU) sponge. In addition, high performance electrode of the honeycomb-like NiCo₂O₄@Ni(OH)₂/TRGN-CNTs-S with core-shell structure has been successfully fabricated through hydrothermal method and then by annealing treatment and electrochemical deposition method, respectively. Benefited from 3D structural feature, the compressed NiCo₂O₄@Ni(OH)₂/TRGN-CNTs-S electrode exhibits high gravimetric and volumetric capacitance of 1810 F g^?1, 847.7 F cm^?3 at 1 A g^?1. The high rate performance and long-term stability was also obtained. Furthermore, an asymmetric supercapacitor using NiCo₂O₄@Ni(OH)₂/TRGN-CNTs-S cathode and NGN/CNTs anode delivered high gravimetric and volumetric energy density of 54 W h kg^?1 at 799.9 W kg^?1 and 37 W h L^?1 at 561.5 W L^?1. In summary, an excellent electrochemical electrode with new elastic 3D SWNTs/graphene supports and binder free pseudocapacitive materials was introduced.     

Fabrication of a novel ZnO–CoO/rGO nanocomposite for nonenzymatic detection of glucose and hydrogen peroxide

Herein, a novel nanocomposite of binary ZnO–CoO nanoparticles loaded on the graphene nanosheets (ZnO–CoO/rGO) has been successfully constructed via a facile, economical and two–step process. The obtained ZnO–CoO/rGO hybrids with high electrical conductivity and abundant active sites, could be modified on a glassy carbon electrode to detect glucose and H₂O₂ multi–functionally. The fabricated biosensor exhibits wide linear range for glucose (10 μM to 11.205 mM) and H₂O₂ (25 μM to 11.1 mM), and their corresponding sensitivity are 168.7 μA mM^?1 cm^?2 and 183.3 μA mM^?1 cm^?2. The limits of detection are 1.3 μM and 0.44 μM for the oxidation of glucose and the reduction of H₂O₂, respectively. Furthermore, remarkable selectivity, long–term stability and outstanding reproducibility of the non–enzyme biosensor prove that ZnO–CoO/rGO hybrids are the promising candidate in practical applications.     

Liquid-phase synthesis of SrCo0.9Nb0.1O3-δ cathode material for proton-conducting solid oxide fuel cells

A novel liquid-phase synthesis strategy is demonstrated for the preparation of the Nb-containing ceramic oxide SrCo_0.9Nb_0.1O_3-δ (SCN). In comparison with the traditional solid-state reaction (SSR) method, the liquid-phase synthesis route offers a couple of advantages, including a lower phase formation temperature and a smaller particle size of the SCN materials that are beneficial for applications as proton-conducting fuel cell cathode. With BaCe_0.4Zr_0.4Y_0.2O_3-δ (BCZY442) as the electrolyte and the SCN synthesized in this work as the cathode, a proton-conducting solid oxide fuel cell (SOFC) shows a peak power density of 348 mW cm^?2 at 700 °C, significantly higher than that of a SOFC fabricated with SCN cathode prepared using the SSR method, which can only deliver 204 mW cm^?2 at the same temperature. Additionally, this new synthesis strategy allows impregnation of Sr²⁺, Co³⁺and Nb⁵⁺ on the solid backbone in aqueous solution, further improving cell performance to reach a peak power density of 488 mW cm^?2 at 700 °C.     

Performance of LiNi1/3Co1/3Mn1/3O2 prepared from spent lithium-ion batteries by a carbonate co-precipitation method

Spherical LiNi_1/3Co_1/3Mn_1/3O₂ cathode particles were resynthesized by a carbonate co-precipitation method using spent lithium-ion batteries (LIBs) as a raw material. The physical characteristics of the Ni_1/3Co_1/3Mn_1/3CO₃ precursor, the (Ni_1/3Co_1/3Mn_1/3)₃O₄ intermediate, and the regenerated LiNi_1/3Co_1/3Mn_1/3O₂ cathode material were investigated by laser particle-size analysis, scanning electron microscopy–energy-dispersive spectroscopy (SEM-EDS), thermogravimetry–differential scanning calorimetry (TG-DSC), X-ray diffraction (XRD), inductively coupled plasma–atomic emission spectroscopy (ICP-AES), and X-ray photoelectron spectroscopy (XPS). The electrochemical performance of the regenerated LiNi_1/3Co_1/3Mn_1/3O₂ was studied by continuous charge–discharge cycling and cyclic voltammetry. The results indicate that the regenerated Ni_1/3Co_1/3Mn_1/3CO₃ precursor comprises uniform spherical particles with a narrow particle-size distribution. The regenerated LiNi_1/3Co_1/3Mn_1/3O₂ comprises spherical particles similar to those of the Ni_1/3Co_1/3Mn_1/3CO₃ precursor, but with a narrower particle-size distribution. Moreover, it has a well-ordered layered structure and a low degree of cation mixing. The regenerated LiNi_1/3Co_1/3Mn_1/3O₂ shows an initial discharge capacity of 163.5 mA h g^?1 at 0.1 C, between 2.7 and 4.3 V; the discharge capacity at 1 C is 135.1 mA h g^?1, and the capacity retention ratio is 94.1% after 50 cycles. Even at the high rate of 5 C, LiNi_1/3Co_1/3Mn_1/3O₂ delivers the high capacity of 112.6 mA h g^?1. These results demonstrate that the electrochemical performance of the regenerated LiNi_1/3Co_1/3Mn_1/3O₂ is comparable to that of a cathode synthesized from fresh materials by carbonate co-precipitation.     

Synthesis of cross-linked graphene aerogel/Fe2O3 nanocomposite with enhanced supercapacitive performance

In this work, cross-linked graphene aerogel (CL-GA) and its composite with Fe₂O₃ nanoparticles (NPs) were synthesized through a one-step hydrothermal procedure by using p-phenylenediamine (PPD). Structural characterizations revealed that in the preparation of the composite PPD acts as a cross-liker and provides high surface area by decreasing restacking of graphene sheets and functions as nitrogen source simultaneously. The electrochemical characteristics of the nanocomposite were investigated by cyclic voltammetry (CV), galvanostatic charge/discharge, electrochemical impedance spectroscopy (EIS) and Fast Fourier transform continues cyclic voltammetry (FFTCCV). The results show that cross-linked graphene aerogel/Fe₂O₃ (CL-GA/Fe₂O₃) nanocomposite displays enhanced supercapacitive performance, where it has capacitance of 445 at 1 A g⁻¹, high energy density of 63 W h Kg⁻¹, and 89% capacitance retention after 5000 cycles in 3 M KOH. Presence of PPD considerably improved supercapacitive performance of nanocomposite as a result it could be promising material in synthesis of efficient graphene/metal oxide-based electrode material for high performance supercapacitors.     

Triethylenediamine-assisted one-step hydrothermal synthesis of polyhedron-shaped Co3S4 for high performance supercapacitor

We describe a facile one-step hydrothermal route to devise and synthesize polyhedron-shaped Co₃S₄ nanomaterial assisted by triethylenediamine (TEDA) as ligand and structure-directing agent. The structural characterizations indicate that the obtained products are Co₃S₄ polyhedral nanoparticles with irregular size, which interconnect and stack each other to construct an interlinked microstructure. When investigated for its supercapacitance property, the as-fabricated Co₃S₄ electrode material exhibits typical pseudocapacitance performances with a high specific capacitance of 1038 F g^?1 at a current density of 0.5 A g^?1 and excellent cycling stability of only 10.2% decay in its original specific capacitance after 1000 galvanostatic charge-discharge cycles, suggesting its potential application in supercapacitor. Importantly, this facile TEDA-assisted hydrothermal method can be universal to obtain other transition metal chalcogenides for supercapacitors.     

Efficient construction of a CoCO3/graphene composite anode material for lithium-ion batteries by stirring solvothermal reaction

Transition-metal carbonates have recently been investigated as anode materials for lithium-ion batteries because of their relatively high capacity compared with that of the corresponding transition-metal oxides. In this work, a facile stirring solvothermal reaction is used to prepare a CoCO₃/graphene composite without the use of an additional organic chelating agent. The as-prepared CoCO₃/graphene composite exhibits a smaller cubic particle size of 1–2 µm and a larger specific surface area than the composite obtained by a traditional solvothermal reaction. The composite prepared with stirring delivers a highly reversible capacity of 602 mAh g^?1 after 100 cycles. Even at a high current density of 2.0 A g^?1, the composite maintains charge–discharge capacities of 605/598 mAh g^?1. The composites contained the same amount of graphene, indicating that the improved electrochemical properties are attained independently of the amount of the graphene. In addition, the results of cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS)experiments also reveal that the CoCO₃/graphene composite electrode materials synthesised via a stirring solvothermal reaction exhibit substantially enhanced kinetics. The stirring solvo/hydrothermal reaction develops in this work is considered a promising candidate for efficiently preparing carbonate/graphene composites with better electrochemical properties for practical applications, without the use of an extra chelating agent.     

Synthesis and electrochemical performance of reduced graphene oxide/maghemite composite anode for lithium ion batteries

Reduced graphene oxide (rGO) tethered with maghemite (γ-Fe₂O₃) was synthesized using a novel modified sol–gel process, where sodium dodecylbenzenesulfonate was introduced into the suspension to prevent the undesirable formation of an iron oxide 3D network. Thus, nearly monodispersed and homogeneously distributed γ-Fe₂O₃ magnetic nanoparticles could be obtained on surface of graphene sheets. The utilized thermal treatment process did not require a reducing agent for reduction of graphene oxide. The morphology and structure of the composites were investigated using various characterization techniques. As-prepared rGO/Fe₂O₃ composites were utilized as anodes for half lithium ion cells. The 40 wt.%-rGO/Fe₂O₃ composite exhibited high reversible capacity of 690 mA h g⁻¹ at current density of 500 mA g⁻¹ and good stability for over 100 cycles, in contrast with that of the pure-Fe₂O₃ nanoparticles which demonstrated rapid degradation to 224 mA h g⁻¹ after 50 cycles. Furthermore, the composite showed good rate capability of 280 mA h g⁻¹ at 10C (∼10,000 mA g⁻¹). These characteristics could be mainly attributed to both the use of an effective binder, poly(acrylic acid) (PAA), and the specific hybrid structures that prevent agglomeration of nanoparticles and provide buffering spaces needed for volume changes of nanoparticles during insertion/extraction of Li ions.     

Structural,magnetic, and textural properties of iron oxide-reduced graphene oxide hybrids and their use for the electrochemical detection of chromium

Superparamagnetic Fe₃O₄ nanoparticles were anchored on reduced graphene oxide (RGO) nanosheets by co-precipitation of iron salts in the presence of different amounts of graphene oxide (GO). A pH dependent zeta potential and good aqueous dispersions were observed for the three hybrids of Fe₃O₄ and RGO. The structure, morphology and microstructure of the hybrids were examined by X-ray diffraction, transmission electron microscopy (TEM), Fourier transform infrared spectroscopy, Raman and X-ray photoelectron spectroscopy. TEM images reveal lattice fringes (d₃₁₁ = 0.26 nm) of Fe₃O₄ nanoparticles with clear stacked layers of RGO nanosheets. The textural properties including the pore size distribution and loading of Fe₃O₄ nanoparticles to form Fe₃O₄–RGO hybrids have been controlled by changing the concentration of GO. An observed maximum (～10 nm) in pore size distribution for the sample with 0.25 mg ml^?1 of GO is different from that prepared using 1.0 mg ml^?1 GO. The superparamagnetic behavior is also lost in the latter and it exhibits a ferrimagnetic nature. The electrochemical behavior of the hybrids towards chromium ion was assessed and a novel electrode system using cyclic voltammetry for the preparation of an electrochemical sensor platform is proposed. The textural properties seem to influence the electrochemical and magnetic behavior of the hybrids.     

Monolithic Fe2O3/graphene hybrid for highly efficient lithium storage and arsenic removal

We fabricated a monolithic Fe₂O₃/graphene hybrid directly by hydrothermal reaction of ferrous oxalate dihydrate and graphene oxide without using a reducing agent. The reduced graphene oxide formed an interconnected network structure that can be used as a support for homogeneous distribution of active Fe₂O₃ nanoparticles. The graphene network and the pore channels in the hybrid facilitate fast electron transfer and ion transport. This hybrid can be directly used as a free-standing anode for lithium ion batteries, which simplifies the fabrication procedure of electrodes, and also exhibited a high capacity of 1062 mA h g⁻¹ at 100 mA g⁻¹, high rate capability and excellent cyclic stability over 100 cycles. Furthermore, as a self-supported adsorbent, it provides a new idea on loading active materials to the suitable substrate, which can be used as a promising material for water purification due to its easy collection and excellent capability in removing As(V) from water. The results demonstrate the promising applications of bulk reduced assembly of graphene with functional metal oxides, which will be helpful for future development of graphene-based multifunctional materials.