Effects of air annealing treatments on the microstructure,components, and mechanical properties of magnetron sputtered Al2O3–Cr2O3–ZrO2 composite coatings

To investigate the effects of air annealing on the microstructure, components, and mechanical properties of ceramic composite coatings, Al₂O₃–Cr₂O₃–ZrO₂ composite coatings were prepared on silicon substrate using radio frequency magnetron sputtering at room temperature, and then air-annealed in a temperature range of 450–850 °C for 30 min. The results indicated that the phase-structure and superficial characteristics, including morphology and surface roughness, were not visibly altered in the annealed coatings up to 600 °C; the elemental component distributions remained uniform. The improvement in the mechanical properties was attributed to the growth of oxide grains. There were no significant changes in the components of Al, Cr, Zr, and O in the annealed coatings. However, an increase in the Cr component and a decrease in the Zr component occurred on the coating surface; the overall structure of the composite coatings possessed a favorable heat resistance. Upon annealing at 750 °C, the thermally-driven formation of uniform and refined nanoparticles on the coating surface was responsible for the effective enhancement of the mechanical properties. Furthermore, annealing at 850 °C induced the enlargement of the precipitated Cr₂O₃ nanoparticles and the generation of micro-defects, resulting in a drastic morphological evolution, an evident increase in the surface roughness, and a significant decrease in the mechanical properties. This study provides new perspectives on designing novel thermal barrier coatings and understanding the role of high temperature air annealing on the microstructural transformation.     

Effect of microstructure and mechanical properties on wear behavior of plasma-sprayed Cr2O3-YSZ-SiC coatings

In this study, the microstructure and mechanical properties of the atmospheric plasma-sprayed Cr₂O₃ (C), Cr₂O₃-20YSZ (CZ), and Cr₂O₃-20YSZ-10SiC (CZS) coatings were evaluated and also compared with each other, so as to explain the coatings wear behavior. Microstructural evaluations included X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM) equipped with energy dispersive X-ray spectroscopy (EDX) and porosity measurements. Mechanical tests including bonding strength, fracture toughness, and micro-hardness tests were used to advance our understanding of the correlation between the coatings properties and their wear behavior. The sliding wear test was conducted using a ball-on-disk configuration against an alumina counterpart at room temperature. Addition of multimodal YSZ and subsequent SiC reinforcements to the Cr₂O₃ matrix resulted in an increase in the fracture toughness and Vickers micro-hardness, respectively. It was found that the composite coatings had comparable coefficients of friction with pure Cr₂O₃ coatings. When compared with the C coating, the CZ and CZS composite coatings with higher fracture toughness exhibited superior wear resistance. Observation of the wear tracks of the coatings indicated that the lower wear rates of the CZ and CZS coatings were due to the higher plastic deformation of the detached materials. In fact, improvement in the wear resistance of the composite coatings was attributed to a phase transformation toughening mechanism associated with tetragonal zirconia which created more ductile tribofilms during the wear test participated in filling the pores of coatings.     

Surface modification of Cr2O3 nanoparticles with 3-amino propyl trimethoxy silane (APTMS). Part 1: Studying the mechanical properties of polyurethane/Cr2O3 nanocomposites

The surface of Cr₂O₃ nanoparticles was modified with various amounts of 3-amino propyl trimethoxy silane (APTMS). Thermal gravimetric analysis (TGA), turbidimeter and Fourier transform infrared (FTIR) spectroscopy were utilized in order to investigate APTMS grafting on the nanoparticles. Then, polyurethane nanocomposites were prepared using various loadings of silane modified Cr₂O₃ nanoparticles. The nanoparticles dispersion in the coating matrix was studied by a field emission scanning electron microscopy (FESEM). Dynamic mechanical thermal analysis (DMTA) and tensile test were utilized in order to investigate the mechanical properties of the nanocomposites. Results obtained from FTIR, TGA and turbidimeter measurements revealed that the organic functional groups of the silane were successfully grafted on the surface of the nanoparticles. The mechanical properties of the polyurethane were significantly enhanced using 2 wt% Cr₂O₃ nanoparticles modified with 0.43 g silane/5 g pigment compared with other samples.     

Correlation between microstructure,chemical components and tribological properties of plasma-sprayed Cr2O3-based coatings

The wear resistance of chromium oxide (Cr₂O₃) coatings could be improved by doping modification and changing the structural scale, etc. In this study, micrometric Cr₂O₃ coatings were doped with different additives, CeO₂ and Nb₂O₅. Moreover, Cr₂O₃ coatings were deposited from nanostructured feedstock by the combination process of plasma spraying and dry-ice blasting. The correlation between the microstructure, chemical components and tribological properties of plasma-sprayed Cr₂O₃-based coatings was discussed based on the investigation of their porosity, hardness and friction behaviors. The results showed that the composite coatings doped with additives exhibited a higher microhardness, corresponding to a lower porosity than pure Cr₂O₃ coating under the identical plasma-spray condition. CeO₂ constituent was found to improve the wear resistance of Cr₂O₃ coating while Nb₂O₅ incorporation corresponds to a steep rise in the friction coefficient. The mismatch of coefficient of thermal expansion (CTE) between Cr₂O₃ and Nb₂O₅ lamellae facilitated the origin of fatigue cracks and the formation of microfracture pits. Although the combination process promotes a porosity reduction, the nanostructured Cr₂O₃ (n-Cr₂O₃) coatings present a lower microhardness than micrometric coatings, due to their loosen microstructure from insufficient plasma power compared to microscaled coatings. The wear mechanisms of both the micro- and nanometric Cr₂O₃ coatings are fatigue cracks and material transfer.     

Mechanical properties of sol–gel prepared nanocomposite coatings in the presence of titania and alumina-derived nanoparticles

Hybrid nanocomposite coatings were prepared by sol–gel method using silica, titania and alumina nanoparticles derived from their alkoxides precursors; in the presence of 3-glycidoxypropyl-trimethoxysilane (GPTMS) and bisphenol A (BPA) on 1050 aluminium alloy substrate. The effect of type and ratio of nanoparticles on mechanical behaviour of the coatings were investigated by dynamic mechanical thermal analysis (DMA) and nanoindentation experiments. DMA results demonstrated that the values of the glass transition temperature (T_g) and the temperature at maximum tan (δ), (T_t) as well as the storage modulus of the hybrid samples depend mainly on the silane content and titania to alumina molar ratio of nanoparticles in the coating composition. In addition, nanoindentaion experiments were performed to study the mechanical properties such as hardness, elastic modulus and E/H ratio for the nanocomposite hybrid coatings. Nanoindentation results indicate that the homogenous reinforced structure was formed in the surface of nanocomposite coating with incorporation of titania and alumina-derived nanoparticles. The incorporation of TiO₂ in comparison with AlOOH nanoparticles in the GPTMS-based coatings showed an improving effect on E/H ratio.     

Al2O3/Si3N4 nanocomposite coating on aluminum alloy by the anodizing route: Fabrication,characterization, mechanical properties and electrochemical behavior

An Al₂O₃/Si₃N₄ nanocomposite coating was successfully fabricated on commercial aluminum alloy. Hardness measurements, polarization and electrochemical impedance spectroscopy (EIS) were employed to study the mechanical and corrosion behaviors of the coatings. Field-Emission Scanning Electron Microscopy (FE-SEM) equipped with Energy Dispersive Spectroscopy (EDS) and X-ray diffraction (XRD) were utilized to characterize the surface morphology and phase composition of the coatings. Also, coatings abrasive wear properties were evaluated with a modified ASTM G105 standard. FE-SEM image, EDS and XRD analysis revealed the presence of Si₃N₄ in the coating. Furthermore, the results showed hardness of the coatings to increase from 380±50 HV for the anodized layer to 712±36 HV for the composite coatings that were formed in an electrolyte containing 6 gr/lit Si₃N₄ nanoparticles. Electrochemical measurements indicated that corrosion resistance of the nanocomposite coating significantly increased compared to the anodized coating. In addition, the effect of Si₃N₄ nanoparticles into the nanocomposite coatings on abrasive wear mechanism and mass loss rate of the coatings was investigated.     

Application of EIS and salt spray tests for investigation of the anticorrosion properties of polyurethane-based nanocomposites containing Cr2O3 nanoparticles modified with 3-amino propyl trimethoxy silane

The Cr₂O₃ nanoparticles were modified with 3-amino propyl trimethoxy silane in order to obtain proper dispersion and increment compatibility with the polyurethane coating matrix. The nanocomposites prepared were applied on the St-37 steel substrates. The existence of 3-amino propyl trimethoxy silane on the surface of the nanoparticles was investigated by Fourier transform infrared (FTIR) spectroscopy and thermal gravimetric analysis (TGA). Dispersion of the surface modified particles in the polyurethane coating matrix was studied by a field emission-scanning electron microscope (FE-SEM). The electrochemical impedance spectroscopy (EIS) and salt spray tests were employed in order to evaluate the corrosion resistance of the polyurethane coatings. Polarization test was done in order to investigate the corrosion inhibition properties of the Cr₂O₃ nanoparticle on the steel surface in 3.5 wt.% NaCl solution. The adhesion strengths of the coatings were evaluated by pull-off adhesion tester before and after 120 days immersion in 3.5 wt.% NaCl solution. FT-IR and TGA analyses revealed that surface modification of the nanoparticles with 0.43 silane/5 g pigment resulted in the greatest amount of silane grafting on the surface of particles. Results obtained from FE-SEM analysis showed that the surface modified nanoparticles dispersed in the coating matrix properly. Results obtained from EIS and salt spray analyses revealed that the surface modified particles enhanced the corrosion protection performance of the polyurethane coating considerably. The improvement was more pronounced for the coating reinforced with 0.43 g silane/5 g pigment. Moreover, the adhesion loss decreased in the presence of surface modified nanoparticles with 0.43 silane/5 g pigment.     

Influence of Cr2O3 particles on corrosion,mechanical and thermal control properties of green PEO coatings on Mg alloy

The influence of micro-sized Cr₂O₃ particles on the corrosion, mechanical and thermal control performance of plasma electrolytic oxidation coated Mg was studied. More contents of Cr₂O₃ particles were embedded into phosphate containing PEO coatings compared with coatings produced from silicate based electrolytes, resulting in green coatings with enhanced thermal control and mechanical property. The existence of particles has slightly improved the corrosion resistance and hardness of the coating. It was found that the absorptance of the coating was increased if higher concentration of Cr₂O₃ particles is incorporated into the layer, which is probably ascribed to low band gap of Cr₂O₃.     

Structure and properties of nanostructured ceramic matrix composite coatings prepared in-situ by reactive plasma spraying micro-sized Al–Fe2O3–Cr2O3 powders

Nanostructured FeAl₂O₄-based ceramic matrix composite coatings were prepared in-situ by reactive plasma spraying micro-sized Al–Fe₂O₃ and Al–Fe₂O₃–Cr₂O₃ powders. The microstructure, toughness, Vickers hardness, and adhesive strength of these coatings were investigated by X-ray diffraction, scanning electron microscopy, transmission electron microscopy and mechanical tests. The results indicated that both the coatings exhibited a nanostructured microstructure. The grains of coating AFC sprayed with Al–Fe₂O₃–Cr₂O₃ powders are finer than those of the coating AF sprayed with Al–Fe₂O₃ powders. The composite nano-coating sprayed with Al–Fe₂O₃–Cr₂O₃ powders exhibited higher hardness and better wear resistance compared with those of the composite nano-coating sprayed with Al–Fe₂O₃ powders. The adhesive strength, toughness, and wear resistance of the composite coating sprayed with Al–Fe₂O₃–Cr₂O₃ powders were significantly enhanced compared with those of the composite coating sprayed with Al–Fe₂O₃ powders, which were attributed to the Cr₂O₃ addition.     

Fabrication of ambient-curable superhydrophobic fluoropolysiloxane/TiO2 nanocomposite coatings with good mechanical properties and durability

Ambient-curable superhydrophobic fluoropolysiloxane/TiO₂ nanocomposite coatings were prepared simply by blending a hydrophobic binder with TiO₂ nanoparticles. The binder consisted of triethoxysilyl-terminated fluoropolysiloxane (FPU), polymethylphenyl-siloxane (PMPS), and 3-aminopropyltriethoxysilane. The surface wettability, morphology, mechanical properties, and artificial weatherability were thoroughly investigated, using contact angle analysis, SEM, AFM, pendulum hardness rocker measurements, and nanoindentation measurements, respectively. Superhydrophobic coatings could be fabricated with FPU/PMPS weight ratios of higher than 1:9, and TiO₂ loads of over 35 wt%. The superhydrophobic coatings had good mechanical strength, excellent artificial weathering durability, and resistance to organic contaminants. It was demonstrated that the TiO₂ nanoparticles acted both as building blocks for the construction of the micro-/nano-structured surface, and as a photocatalyst for the decomposition of organic contaminants.     

Impact of Al2O3-40 wt.% TiO2 feedstock powder characteristics on the sprayability,microstructure and mechanical properties of plasma sprayed coatings

Atmospheric plasma sprayed (APS) Al₂O₃-TiO₂ coatings have found a wide range of industrial application due to their favorable properties, combined with low costs and a high availability. However, the detailed effect of the phase composition and the element distribution of the feedstock powders on the coating properties and the spraying process have only crudely been investigated so far. Here the impact of aluminum titanate (Al₂TiO₅) on the microstructural features and mechanical properties of Al₂O₃-40 wt.% TiO₂ APS coatings is demonstrated by investigating the detailed phase composition and the distribution of aluminum and titanium in three fused and crushed feedstock powders and the respective coatings. Thereby, a direct influence of Al₂TiO₅ content on the deposition efficiency, the porosity, the elastic modulus, and the hardness of the coatings is revealed. The results emphasize the need for a more detailed specification of commercial Al₂O₃-TiO₂ feedstock powders to ensure a high reliability of the coating properties.     

Crystal structure and properties of Al2O3-Cr2O3 solid solutions with different Cr2O3 contents

To enable the comprehensive application of Al₂O₃-Cr₂O₃ solid solutions, the crystal structures and properties of Al₂O₃-Cr₂O₃ solid solutions with different Cr₂O₃ contents were studied. It was observed that Al₂O₃ and Cr₂O₃ form a complete substitutional solid solution over the entire composition range at 1650 °C, with no compounds being formed. Lattice parameters “a” and “c” both increase linearly with an increase in the Cr₂O₃ content. The doping of the Cr³⁺ ions causes a more severe lattice strain in the c-axis direction. The diffraction angles of the diffraction peaks decrease in a linear manner with the increase in the Cr₂O₃ content. The relationship between the theoretical density of the solid solution and the Cr₂O₃ content could be fitted using a second-order polynomial. It was also observed that the linear expansion coefficient of the solid solutions decreases with an increase in the Cr₂O₃ content.     

Investigation of surface modification of rutile TiO2 nanoparticles with SiO2/Al2O3 on the properties of polyacrylic composite coating

Surface modification and characterization of TiO₂ nanoparticles as an additive in a polyacrylic clear coating were investigated. For the improvement of nanoparticles dispersion and the decreasing of photocatalytic activity, the surface of nanoparticles was modified with binary SiO₂/Al₂O₃. The surface treatment of TiO₂ nanoparticles was characterized with FTIR. Microstructural analysis was done by AFM. The size, particle size distribution and zeta potential of TiO₂ nanoparticles in water dispersion was measured by DLS method. For the evaluation of particle size and the stability of nanoparticles in water dispersions with higher solid content the electroacoustic spectroscopy was made. To determine the applicability and evaluate the transmittance of the nano-TiO₂ composite coatings UV–VIS spectroscopy in the wavelength range of 200–800 nm was employed. The results showed that surface treatment of TiO₂ nanoparticles with SiO₂/Al₂O₃ improves nanoparticles dispersion and UV protection of the clear polyacrylic composite coating.     

Improved mechanical and wear properties of hybrid Al-Al2O3/GNPs electro-less coated Ni nanocomposite

Al was successfully reinforced with two ceramics Al₂O₃ coated Ni and graphene nanoplatelets (GNPs) coated Ni by electro-less deposition technique to form Al-Al₂O₃/$\mathit{x}$ GNPs hybrid nanocomposite ($\mathit{x}=0,0.2,0.6,1$and $1.4\%$) with improved mechanical and wear properties. Compressive strength, hardness, wear properties and coefficient of friction were investigated. The results indicated that increasing GNPs volume fraction improves compressive strength, hardness and antifriction properties of composites significantly. In comparison with pure aluminum, 1.52- fold increases in the strength, 2.45-fold increase in the hardness and 19.2-fold decreases in the wear rate of Al-10%Al₂O₃/1.4%GNPs nanocomposite are achieved. This improvement is attributed to the remarkable mechanical strength and excellent self-lubrication of grapheme, the reduction of grain size during electro-less deposition process and the increased efficient stress transfer due to the curled structure of GNPs. Additionally, coating GNPs with Ni particles prevent the formation of Al₃C₄ intermetallic phase which lead to this large improvement in the wear rate. In comparison with the available results in the literature, electro-less coating of GNPs with Ni provides 2.1 times larger hardness than composite with uncoated GNPs.     

Effect of Ti amount on wear and corrosion properties of Ti-doped Al2O3 nanocomposite ceramic coated CP titanium implant material

Al₂O₃ and Ti-doped Al₂O₃ nanocomposite ceramic coatings were prepared by using a sol-gel dip-coating process. Corrosion and wear resistance of Al₂O₃ ceramic coatings in relation to Ti amount were carried out using pin-on-disk tribotester, potentiodynamic polarization and electrochemical impedance spectroscopy (EIS). Surface characterizations before and after the corrosion and wear tests were investigated by the scanning electron microscope (SEM) and X-ray diffraction (XRD) and hardness analysis. The results of corrosion and wear tests exhibited that the corrosion and wear resistance of nanocomposite ceramic coatings became better than uncoated samples. Also, corrosion and wear resistance of nanocomposite ceramic coatings improved with Ti doping content increased.     

Influence of Y2O3 on the microstructure and tribological properties of Ti-based wear-resistant laser-clad layers on TC4 alloy

Multi-track Ti-based wear-resistant composite coatings were fabricated on TC4 alloy surfaces using laser-clad TC4 + Ni45 + Co–WC mixed powders with different Y₂O₃ contents (0, 1, and 3 wt%). The microstructure, microhardness, and tribological properties of the coatings were characterised using X-ray diffraction, scanning electron microscopy, energy dispersive spectrometry, electron probe X-ray micro analyser, microhardness tester, and friction and wear testing apparatus. The results showed that the number of cracks on the coating surfaces gradually decreased with the addition of Y₂O₃ and that residual Co–WC powders existed in the coating subsurfaces. The phase composition of the coatings with different Y₂O₃ contents remained unchanged and was mainly composed of reinforcing phases of TiC, TiB₂, Ti₂Ni, and matrix α-Ti. With the addition of Y₂O₃, the coating microstructure was remarkably refined, the direction characteristic of the TiC dendrites obviously weakened, and the nucleation rate significantly increased. When the added Y₂O₃ was 3 wt%, a large amount of TiB₂–TiC-dependent growth composite phases precipitated in the coating. The two-dimensional lattice misfit between (0001)_TiB2 and (111)_TiC was 0.912%, which indicated that TiB₂ and TiC formed a coherent interface. When the amount of Y₂O₃ was increased, the microhardness of the coatings gradually decreased, and the wear volume of the coatings first increased and then decreased. Under the effect of the TiB₂–TiC composite phases, the wear resistance of the 3 wt% Y₂O₃ coating was optimal. The 3 wt% Y₂O₃ coating friction coefficient was the lowest, and the wear mechanism was abrasive wear.     

Development of poly(vinylcarbazole)/alumina nanocomposite coatings for corrosion protection of 316L stainless steel in 3.5% NaCl medium

Poly(vinylcarbazole) (PVK) and PVK‐alumina (Al₂O₃) nanocomposite coatings were electrochemically coated on 316 L stainless steel (SS) substrates for corrosion protection of 316 L SS in 3.5 weight (wt) % NaCl medium. The formation of PVK and incorporation of nanoalumina particles in PVK‐Al₂O₃ nanocomposite coatings were confirmed from attenuated total reflectance‐infrared spectroscopy (ATR‐IR). Thermal analysis (TG) results showed enhanced thermal stability for the composites relative to PVK. Incorporation of Al₂O₃ nanoparticles enhanced the micro hardness of PVK coated 316 L SS. The dispersion of alumina nanoparticles was examined via scanning electron microscope (SEM) and tunneling electron microscopy (TEM) and revealed distinct features. The influence of nanoparticles on the barrier properties of PVK and PVK‐Al₂O₃ nanocomposites was evaluated in aqueous 3.5 wt % NaCl by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) studies. The results proved that PVK nanocomposite coatings provided better protection for 316 L SS than PVK coatings. The drastic increase in impedance values is due to the high corrosion resistance offered by the PVK nanocomposite coatings that arises due to the interaction between Al₂O₃ nanoparticles and PVK. The highest corrosion protection shown by the 2 wt % nano Al₂O₃ incorporated PVK composite coatings proved enhanced corrosion resistance compared to PVK. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44937.     

Microwave assisted hydrothermal synthesis of (Fe,Co)3O4 nanoparticles in the presence of surfactants and effects of Co/Fe ratio on microstructure and magnetism

Microstructure and magnetic properties of nanoparticles can be tailored by optimising the synthesis procedure and changing chemical composition. In this study, a two-step procedure, i.e., coprecipitation in the presence of PEG 300 followed by microwave assisted (MW) hydrothermal synthesis, was introduced to obtain Co_xFe_3-xO₄ (x?=?0, 0.1 and 0.2) nanoparticles. It was found that with the increase of Co content, particle/crystallite size increased, with significant change of coercivity (H_c). The mixed samples of Co_xFe_3-xO₄ (x?=?0.1 and 0.2) were magnetically harder in comparison with Fe₃O₄. Тhe H_c of Fe₃O₄ was 91?Oe, while for Co_0.10Fe_2.90O₄ and Co_0.20Fe_2.80O₄, H_c was 256?Oe and 1070?Oe, respectively. Saturation magnetisation (M_s) of mixed samples also increased up to 6% compared to Fe₃O₄. A special effort was devoted to study the effects of introducing different surfactants (PEG 300, PEG 4000 or SDS) during the synthesis procedure in order to improve morphological and microstructural properties of CoFe₂O₄ nanoparticles. The influence of surfactants on physical/chemical properties of nanoparticles is discussed.     

Mechanical and tribological properties of nano/micro composite alumina coatings fabricated by atmospheric plasma spraying

Adding nano particles can significantly improve the mechanical properties and wear resistance of thermal sprayed Al₂O₃ coating. However, it still remains a challenge to uniformly incorporate nano particles into traditional coatings due to their bad dispersibility. In the present work, nanometer Al₂O₃ (n-Al₂O₃) powders modified by KH-560 silane coupling agent were introduced into micrometer Al₂O₃ (m-Al₂O₃) powders by ultrasonic dispersion to afford nano/micro composite feedstock, and then four resultant coatings (weight fraction of n-Al₂O₃: 0%, 3%, 5% and 10%) were fabricated by atmospheric plasma spraying. The features and constitutes of feedstock and as-sprayed coatings, as well as their porosity, bonding strength, microhardness and frictional behaviors were investigated in detail. Results show that the nano/micro composite feedstock with uniform microstructure can be better melted in the spraying process, thereby obtaining coatings with denser microstructure, higher hardness and bonding strength. Added n-Al₂O₃ has no obvious effect on the friction coefficient of composite coatings, whereas can improve their wear-resistant and reduce the worn degree of counterpart. The wear mechanism of traditional coating is brittle fracture and lamellar peeling, while that of composite coating with weight fraction of n-Al₂O₃ of 10% is adhesive wear.     

Structural and magnetic properties of Co/Al2O3 cermet synthesized by mechanical ball milling

Cobalt nanoparticles in the alumina matrix were synthesized using high energy mechanical ball milling of Co₃O₄ and Al powders mixture. The effect of ball mill time of 1 up to 12 h on the phase formation and crystalline lattice of the samples was investigated by the fitting of the X-ray diffraction patterns with Fullprof software and Rietveld method. The results show that 6 h milling of the primary powders yields a nanocomposite of Co/Al₂O₃ cermet. The formation of Co/Al₂O₃ nanocomposite was confirmed by a morphological study using scanning electron microscopy and transmission electron microscopy. The prepared nanocomposite by 12 h ball mill time has ferromagnetic properties with a high saturation magnetization value of 118 emu/g. Also, using Henkel plot analysis, it was shown that there are strong dipole-dipole magnetic interactions between the prepared cobalt nanoparticles in the Al₂O₃ matrix.