TiO2 nano-flakes with high activity obtained from phosphorus doped TiO2 nanoparticles by hydrothermal method

TiO₂ nano-wires (Ti-NWs) and nano-flakes (Ti-NFs) were obtained from phosphorus doped TiO₂ nanoparticles (Ti-P) by hydrothermal method and by subsequent heat treatment respectively. FE-SEM micrograph of the as prepared sample depicts well formed, entangled and randomly oriented nano-wires morphology, which changes to nano-flakes morphology after heat treatment. Structural characterization of the samples by X-ray diffraction shows anatase phase for both the samples. Absorption edge of the Ti-NWs sample shows blueshift where as the Ti-NFs sample exhibit redshift compared to precursor sample as evidenced by UV–Visible absorption spectra, which is due to change in morphology and crystallinity of the samples. XPS studies indicate the presence of titanium and oxygen species only. From the EPR measurements with in-situ visible light irradiation, the number of photogenerated charge carriers is found to be very high for nano-flakes sample. Methyleneblue degradation profiles depict very high activity of Ti-NFs sample compared to Ti-NWs and the precursor samples, which is due to the observed redshift in the absorption edge, change in morphology and high crystallinity of the sample which in turn increases the optical response and separation of photogenerated charge carriers as evidenced by the optical and EPR measurements respectively.     

SO2 resistant antimony promoted V2O5/TiO2 catalyst for NH3-SCR of NOx at low temperatures

To get the low temperature sulfur resistant V₂O₅/TiO₂ catalysts quantum chemical calculation study was carried out. After selecting suitable promoters (Se, Sb, Cu, S, B, Bi, Pb and P), respective metal promoted V₂O₅/TiO₂ catalysts were prepared by impregnation method and characterized by X-ray diffraction (XRD) and Brunner Emmett Teller surface area (BET-SA). Se, Sb, Cu, S promoted V₂O₅/TiO₂ catalysts showed high catalytic activity for NH₃ selective catalytic reduction (NH₃-SCR) of NO_x carried at temperatures between 150 and 400 °C. The conversion efficiency followed in the order of Se > Sb > S > V₂O₅/TiO₂ > Cu but Se was excluded because of its high vapor pressure. An optimal 2 wt% ‘Sb’ loading was found over V₂O₅/TiO₂ for maximum NO_x conversion, which also showed high resistance to SO₂ in presence of water when compared to other metal promoters. In situ electrical conductivity measurement was carried out for Sb(2%)/V₂O₅/TiO₂ and compared with commercial W(10%)V₂O₅/TiO₂ catalyst. High electrical conductivity difference (ΔG) for Sb(2%)/V₂O₅/TiO₂ catalyst with temperature was observed. SO₂ deactivation experiments were carried out for Sb(2%)/V₂O₅/TiO₂ and W(10%)/V₂O₅/TiO₂ at a temperature of 230 °C for 90 h, resulted Sb(2%)/V₂O₅/TiO₂ was efficient catalyst. BET-SA, X-ray photoelectron spectroscopy (XPS) and carbon, hydrogen, nitrogen and sulfur (CHNS) elemental analysis of spent catalysts well proved the presence of high ammonium sulfate salts over W(10%)/V₂O₅/TiO₂ than Sb(2%)/V₂O₅/TiO₂ catalyst.     

TiO2, TiO2/Ag and TiO2/Au photocatalysts prepared by spray pyrolysis

TiO₂, TiO₂/Ag and TiO₂/Au photocatalysts exhibiting a hollow spherical morphology were prepared by spray pyrolysis of aqueous solutions of titanium citrate complex and titanium oxalate precursors in one-step. Effects of precursor concentration and spray pyrolysis temperature were investigated. By subsequent heat treatment, photocatalysts with phase compositions from 10 to 100% rutile and crystallite sizes from 12 to 120 nm were obtained. A correlation between precursor concentration and size of the hollow spherical agglomerates obtained during spray pyrolysis was established. The anatase to rutile transformation was enhanced with metal incorporations and increased precursor concentration. The photocatalytic activity was evaluated by oxidation of methylene blue under UV-irradiation. As-prepared TiO₂ particles with large amounts of amorphous phase and organic residuals showed similar photocatalytic activity as the commercial Degussa P25. The metal incorporated samples showed comparable photocatalytic activity to the pure TiO₂ photocatalysts.     

Effects of annealing temperature on the photocatalytic activity of N-doped TiO2 thin films

The effects of annealing temperature on the photocatalytic activity of nitrogen-doped (N-doped) titanium oxide (TiO₂) thin films deposited on soda-lime-silica slide glass by radio frequency (RF) magnetron sputtering have been studied. Glancing incident X-ray diffraction (GIAXRD), Raman spectrum, scanning electron microscopy (SEM), atomic force microscopy (AFM) and UV-vis spectra were utilized to characterize the N-doped TiO₂ thin films with and without annealing treatment. GIAXRD and Raman results show as-deposited N-doped TiO₂ thin films to be nearly amorphous and that the rutile and anatase phases coexisted when the N-doped TiO₂ thin films were annealed at 623 and 823 K for 1 h, respectively. SEM microstructure shows uniformly close packed and nearly round particles with a size of about 10 nm which are on the slide glass surface for TiO₂ thin films annealed at 623 K for 1 h. AFM image shows the lowest surface roughness for the N-doped TiO₂ thin films annealed at 623 K for 1 h. The N-doped TiO₂ thin films annealed at 623 K for 1 h exhibit the best photocatalytic activity, with a rate constant (k_a) of about 0.0034 h⁻¹.     

Preparation of ZrO2/Gd2O3 composite ceramic materials by coprecipitation method

High burnup is a goal for further development of advanced nuclear power in the future. However, along with the increase of burnup, it becomes more diffidult to control reactor reactivity, which affects the operation safety of the nuclear reactor. Al₂O₃/B₄C burnable poison materials widely used in pressurized water reactor currently will not meet the requirements of burnable poison materials in high burnup nuclear power. Because of the better performance of ZrO₂/Gd₂O₃ burnable poison materials than that of Al₂O₃/B₄C, this paper studies the preparation of ZrO₂/Gd₂O₃ composite ceramic materials by the coprecipitation method. The experimental results show that at the sintering temperature of 1500–1650 °C, ZrO₂/Gd₂O₃ composite ceramic grains are small, compact and uniform with the generation of homogeneous solid solution. At 1600 °C, ZrO₂–10%Gd₂O₃ has the highest density and mechanical strength.     

Synthesis of nanosized (Pb,Sr)TiO3 perovskite powders by coprecipitation processing

Nanosized perovskite lead strontium titanate (Pb_xSr_1−x)TiO₃ (PST) powders were successfully prepared by a simple coprecipitation method. Lead-strontium titanyl oxalate (PSTO) precursor was first synthesized at room temperature, and the precursor was then calcined at 600 °C for 1 h to produce the single phase perovskite PST powders. Characterization studies were carried out on the as-dried precursor and the calcined PST powders by various techniques. The results showed a strong dependence of the chemical composition of final PST powders on pH value in the coprecipitation reaction. PST powders with desired composition could be synthesized by adding 25 mol% excess Sr. PST particles were found to be spherical in nature with an average size of 10 nm.     

低温固相合成超细正硼酸镍粉体

探讨了采用不同镍源对合成产物正硼酸镍［Ni₃（BO₃）₂］的影响,最终确定以碱式碳酸镍［NiCO₃·2Ni（OH）₂·4H₂O］为镍源与硼酸（H₃BO₃）在较低温度下按化学计量比反应得到目标产物,并通过X射线衍射（XRD）、红外光谱（IR）和扫描电镜（SEM）对产物结构及形貌进行表征。结合XRD和IR分析结果表明,采用碱式碳酸镍为镍源,与硼酸按照化学计量比,仅在700 ℃焙烧3 h即得到纯净正交结构的Ni₃（BO₃）₂。通过SEM可观察到不使用有机溶剂情况下,采用碱式碳酸镍和硼酸直接焙烧制备的产物分散性好、粒径分布均匀且主要分布在200~250 nm。     

TiO2 nanotubes and CNT–TiO2 hybrid materials for the photocatalytic oxidation of propene at low concentration

In this work, we investigated titanium dioxide (TiO₂) nanotubes and CNT–TiO₂ hybrid materials for the photocatalytic oxidation (PCO) of propene at low concentration (100 ppmv) in gaseous phase. The materials were prepared via sol–gel method using sacrificial multi-walled carbon nanotubes (CNT) as templates and subsequent heat treatments to obtain the desired crystalline phase (anatase, rutile or a mixture of both) and eventually to remove the carbon template. We also studied rutile nanotubes for the first time and demonstrate that the activity strongly depends on the crystalline composition, following rutile < anatase < anatase/rutile mixture. The enhanced activity of the anatase–rutile mixture is attributed to the decrease in the electron–hole pair recombination due to the multiphasic nature of the particles. The key result of this work is the exceptional performance of the CNT–TiO₂ hybrid, which yielded the highest observed photocatalytic activity. The improved performance is attributed to synergistic effects due to the hybrid nature of the material, resulting in small anatase crystalline sizes (CNT act as heat sinks) and a reduced electron–hole pair recombination rate (CNTs act as electron traps). These results demonstrate the great potential of hybrid materials and stimulate further research on CNT-inorganic hybrid materials in photocatalysis and related areas.     

Low temperature preparation and visible light photocatalytic activity of mesoporous carbon-doped crystalline TiO2

A visible-light-active TiO₂ photocatalyst was prepared through carbon doping by using glucose as carbon source. Different from the previous carbon-doped TiO₂ prepared at high temperature, our preparation was performed by a hydrothermal method at temperature as low as 160 °C. The resulting photocatalyst was characterized by XRD, XPS, TEM, nitrogen adsorption, and UV–vis diffuse reflectance spectroscopy. The characterizations found that the photocatalyst possessed a homogeneous pore diameter about 8 nm and a high surface area of 126 m²/g. Comparing to undoped TiO₂, the carbon-doped TiO₂ showed obvious absorption in the 400–450 nm range with a red shift in the band gap transition. It was found that the resulting carbon-doped TiO₂ exhibits significantly higher photocatalytic activity than the undoped counterpart and Degussa P25 on the degradation of rhodamine B (RhB) in water under visible light irradiation (λ > 420 nm). This method can be easily scaled up for industrial production of visible-light driven photocatalyst for pollutants removal because of its convenience and energy-saving.     

Carbon-modified TiO2 photocatalyst by ethanol carbonisation

The new photocatalysts based on commercially available titanium dioxide powders: Tytanpol A11 (Police, Poland), pure anatase and P-25 (Degussa, Germany) containing about 20% rutile were modified by carbon via ethanol carbonisation. Titanium dioxides were heated at different temperature from 150 to 400 °C for 1 h in an atmosphere of ethanol vapour. The photocatalytic activity of carbon-modified TiO₂ was studied by oxidation of phenol in water under UV and artificial solar light irradiation. With increasing of carbon content in TiO₂ photocatalysts the activity for phenol decomposition under UV light was decreasing but that under visible light was stable. Turbidity of the slurry solution decreased with increasing of carbon content for all prepared photocatalysts because of the change of their surface character from hydrophilic to hydrophobic.     

Photocatalytic activity of Cu2O/TiO2, Bi2O3/TiO2 and ZnMn2O4/TiO2 heterojunctions

Cu₂O/TiO₂, Bi₂O₃/TiO₂ and ZnMn₂O₄/TiO₂ heterojunctions were studied for potential applications in water decontamination technology and their capacity to induce an oxidation process under VIS light. UV–vis spectroscopy analysis showed that the junctions-based Cu₂O, Bi₂O₃ and ZnMn₂O₄ are able to absorb a large part of visible light (respectively, up to 650, 460 and 1000 nm). This fact was confirmed in the case of Cu₂O/TiO₂ and Bi₂O₃/TiO₂ by photocatalytic experiments performed under visible light. A part of the charge recombination that can take place when both semiconductors are excited was observed when a photocatalytic experiment was performed under UV–vis illumination. Orange II, 4-hydroxybenzoic and benzamide were used as pollutants in the experiment. Photoactivity of the junctions was found to be strongly dependent on the substrate. The different phenomena that were observed in each case are discussed.     

Synthesis and electrochemical studies of a layered spheric TiO2 through low temperature solvothermal method

This paper demonstrates a low temperature solvothermal method for the synthesis of a layered spheric TiO₂. The crystal structure and morphology of the material were characterized by using X-ray diffraction (XRD) and scanning electron miscopy (SEM). Electrochemical performances of the TiO₂ when used as anode material in lithium ion batteries were investigated by galvanostatic charge/discharge and cyclic voltammetry experiments. A discharge capacity of 179 mAh g⁻¹ was obtained in the potential range between 3.0 and 1.5 V. No significant capacity decay was observed in the successive 30 cycles showing satisfactory cycling performance of the electrode.     

Inorganic gels as precursors of TiO2 photocatalysts prepared by low temperature microwave or thermal treatment

A simple procedure for preparing active TiO₂ photocatalysts is presented. The starting materials were unusual TiO₂ gels formed from TiCl₄. The use of microwaves for a very short time enhanced the TiO₂ crystallinity preventing an increase of particle size and minimizing the decrease of specific surface area. This result makes this preparation very attractive. The formation of the gels was monitored through measurements of viscosity. All the samples were characterized by means of X-ray diffraction, diffuse reflectance spectroscopy and BET specific surface area measurements. The photoactivity of the samples was evaluated using the photodegradation of 4-nitrophenol in liquid–solid regimen and gaseous 2-propanol as probe reactions. Commercial TiO₂ Degussa P25 was used for the sake of comparison.     

Photocatalytic degradation of methylene blue with TiO2 nanoparticles prepared by a thermal decomposition process

The generation of TiO₂ nanoparticles by the thermal decomposition of titanium tetraisopropoxide (TTIP) was carried out experimentally using a tubular electric furnace at various synthesis temperatures (700-1300 °C) and TTIP heating temperatures (80-110 °C). The photocatalytic activity of the resulting TiO₂ nanoparticles was examined by measuring the rate of methylene blue decomposition. The TiO₂ nanoparticles were characterized by X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET) measurements and transmission electron microscopy (TEM). The crystallite size and crystallinity increased with increasing synthesis temperature and TTIP heating temperature. A TTIP heating temperature and synthesis temperature of 95 °C and 900 °C, respectively, were found to be the optimal synthesis conditions. The primary particle diameter obtained under optimum synthesis conditions was considerably smaller than the commercial photocatalyst (Degussa, P25). The specific surface areas were more than 134.4 m² g^− 1. Under the optimal conditions, the photocatalytic activity for methylene blue was higher than that of the commercial photocatalyst.     

Characterization and photocatalytic activity of N-doped TiO2 prepared by thermal decomposition of Ti–melamine complex

Nitrogen doped spherical TiO₂ has been prepared by thermal decomposition of Ti–melamine complex in air atmosphere. A clear shift in the onset light absorption from UV region (<400) to visible region (>520 nm) has been observed for the N-doped samples. It has been deduced from the optical absorption spectra that the higher calcination temperature results in the decrease in the amount of N-doping. The XRD results revealed the phase transition of TiO₂ from anatase to rutile crystalline phase, starting at calcination temperature ≥600 °C. The electron microscopic images reveal the formation of spherical and flakes of TiO₂ nanocrystals (25 nm). The chemical nature of N in the N-TiO₂ has been evolved through X-ray photoelectron spectroscopy. The presence of different types of N species have been observed corresponding to different oxidation states and the presence of Ti–N and O–Ti–N have been confirmed from the observed binding energy values. Photocatalytic decomposition of methylene blue has been carried out both in the visible region and UV + visible region. In the visible region, N-TiO₂ showed higher activity compared to the undoped commercial TiO₂ (Degussa P25).     

Synthesis of TiO2 nanoparticles by a combined sol-gel ball milling method and investigation of nanoparticle size effect on their photocatalytic activities

TiO₂ nanoparticles were synthesized by a sol-gel method and the effect of ball milling of dried gel on the particle size has been investigated. The results show that the ball milling has a crucial role in preparation of nanosized TiO₂ powder. Also thermal treatment at different temperatures can control the size of prepared nanoparticles. The photocatalytic activities of TiO₂ nanoparticles with different sizes were studied by photocatalytic degradation of Congo red dye using a homemade photoreactor. The photo degradation of Congo red dye was monitored by UV-Vis absorption measurements. It was found that the nanopowders which were synthesized at 550 °C with average particle size of 55 nm show the maximum photocatalytic activities. These nanopowders which were a mixture of anatase and rutile phases did not show the same photocatalytic effect on Eriochrome black, Bromocresol green, Methyl orange and Rose Bengal dyes.     

Effect of Al2O3-SiO2 substrate on gas-sensing properties of TiO2 based lambda sensor at high temperature

Alumina is widely used as substrate material for oxygen lambda sensors. It has been reported that response properties of sensors are highly dependent on surface state of substrates. In this work, Al₂O₃-x%SiO₂ (x = 2–30) substrates were specially prepared for TiO₂ based lambda sensors for high temperature operation. Structure and surface state of prepared substrates were characterized by XRD, SEM and XPS. TiO₂ sensing film was prepared by screen printing method. Results indicated that sensors fabricated on Al₂O₃-10%SiO₂ substrate exhibited the best sensing properties. Moreover, final steady-state voltages of all sensors were limited to less than 100 mV at 600–800 ℃.     

Co/CeO2-ZrO2 catalysts prepared by impregnation and coprecipitation for ethanol steam reforming

Co/CeO₂-ZrO₂ catalysts for the ethanol steam reforming were prepared by wet incipient impregnation and coprecipitation methods. These catalysts were characterized by nitrogen adsorption, TEM-EDX, XRD, H₂-TPR, and CO chemisorption techniques. It was found that the catalyst reducibility was influenced by the preparation methods; catalysts with different reduction behaviors in the pre-reduction showed different catalytic activities toward hydrogen production. The H₂-TPR studies suggested the presence of metal–support interactions in Co/CeO₂-ZrO₂ catalysts during their hydrogen pre-reduction, a necessary treatment process for catalysts activation. These interactions were influenced by the preparation methods, and the impregnation method is a favorable method to induce a proper metal–support effect that allows only partial reduction of the cobalt species and leads to a superior catalytic activity for the hydrogen production through ethanol steam reforming. At 450 °C, the impregnated catalyst gives a hydrogen production rate of 147.3 mmol/g-s at a WHSV of 6.3 h⁻¹ (ethanol) and a steam-to-carbon ratio of 6.5.     

Synthesis of Bi2O3/TiO2 nanostructured films for photocatalytic applications

Dendritic growth of bismuth oxide nanostructured films was accomplished by reactive magnetron sputtering. The deposition of the Bi₂O₃ template layers was adapted to abide a vapour-liquid-solid mechanism in order to develop a 3D growth morphology with high surface area templates for photocatalytic applications. TiO₂ photocatalytic thin films were deposited at a later stage onto Bi₂O₃ layers. The obtained heterostructured films were characterized by scanning electron microscopy, X-ray diffraction and atomic force microscopy. Additionally, the photocatalytic efficiency was assessed by conducting an assay using methylene blue dye as testing pollutant under a UV-A illumination. The photocatalytic tests revealed that the Bi₂O₃ layers functionalized with TiO₂ thin films are more efficient at degrading the pollutant, by a factor of 6, when compared with the individual layered films.