Enhanced dielectric and piezoelectric properties in Na0.5Bi4.5Ti4O15 ceramics with Pr-doping

The bismuth layer-structured Na_0.5Bi_4.5-xPr_xTi₄O₁₅ (x?=?0, 0.1, 0.2, 0.3, 0.4, and 0.5) (NBT-xPr³⁺) ceramics were fabricated using the traditional solid reaction process. The effect of different Pr³⁺ contents on dielectric, ferroelectric and piezoelectric properties of Na_0.5Bi_4.5Ti₄O₁₅ ceramics were investigated. The grain size of Pr³⁺-doping ceramics was found to be smaller than that of pure one, the maximum dielectric constant and Curie temperature T_c gradually decreased with increasing Pr³⁺ contents, and the dielectric loss decreased at high temperature by Pr³⁺-doping. Moreover, the activation energy (E_a), resistivity (Z’), remanent polarization (2P_r) and piezoelectric constant (d₃₃) increased by Pr³⁺-doping. The NBT-xPr³⁺ ceramics with x?=?0.3 achieved the optimal properties with the maximum dielectric constant of 1109.18, minimum loss of 0.00822 (250?kHz), E_a of 1.122?eV, Z’ of 7.9?kΩ?cm (725 ºC), d₃₃ of 18 pC/N, 2P_r of 12.04 μC/cm². The enhancement was due to the addition of Pr³⁺ which suppressed the decreasing of resistivity at high temperature and made it possible for NBT-xPr³⁺ ceramics to be poled in perpendicular direction, implying that it is a great improvement for Na_0.5Bi_4.5Ti₄O₁₅ ceramics in electrical properties.     

Dielectric and optical properties of Ni doped Na0.5Bi0.5TiO3

Polycrystalline Ni doped Na_.5Bi_0.5TiO₃ samples (Na_0.5Bi_0.5)Ti_1-xNi_xO_3, (x?=?0.5, 0.10, 0.15) have been prepared by solid state reaction. The appearance of the additional peak in X-ray diffraction pattern indicates the ordering of Ti⁴⁺ and Ni²⁺ ions. Polygonal grains are converted into flakes with an increase of Ni concentration. Replacement of Ti⁴⁺ by Ni²⁺ strongly modifies the relative contribution of two peaks in the Raman bands within 200–400?cm^?1. Oxygen vacancy is observed in X-ray photoelectron spectrum to maintain charge neutrality due to aliovalent doping. Broad diffuse phase transition centered at the dielectric constant maximum indicates relaxor behaviour. Comparison between impedance and electric modulus spectrum suggests non-Debye relaxation. The ac conductivity follows the power law with the frequency exponent lies 0.52???0.72. The generation of holes by divalent Ni dopant at tetravalent Ti sites enhances optical band gap.     

Effects of Nd3+ and high-valence Nb5+ co-doping on the structural,dielectric and magnetic properties of BiFeO3 multiferroics

Bi_0.90Nd_0.10Fe_1?xNb_xO₃ (0 ≤ x ≤ 0.05) multiferroics have been studied to reveal the effect of Nb doping on the physical properties of the neodymium modified BiFeO₃. These samples have been synthesized via conventional solid state reaction method. The structural characterization was performed by XRD technique and Rietveld refinement. Rietveld refinement results confirmed that all samples crystallized in rhombohedral symmetry. In the vicinity of anti-ferromagnetic Neel-temperature (T_N), an anomaly was observed in dielectric constant (?′) and loss tangent (tan δ) which indicates the existence of magnetoelectric coupling. It is observed that with Nb doping dielectric constant was reduced and Neel temperature shifted towards higher temperature. The impedance (Nyquist plots) and modulus spectroscopy revealed that materials possess non-Debye type of relaxation. The doping of donor ion is able to suppress the existence of oxygen vacancies which results in increase in resistivity. The B-site doping by higher valence ion suppresses the existing modulated spin structure by structural distortion, results in released net magnetization. The room temperature remanent magnetization increased with Nb doping and all powder samples possess weak ferromagnetism. The possible reasons for the notable magnetic and dielectric performance of prepared samples were discussed.     

Enhancement in electrical and magnetic properties of (Li0.5Ga0.5)2+ and (Li0.5Er0.5)2+-Modified BiFeO3-BaTiO3 ceramics

Effects of (Li_0.5Ga_0.5)²⁺ and (Li_0.5Er_0.5)²⁺ doping on the phase structure, electrical, and magnetic properties of 0.75BiFeO₃-0.25BaTiO₃ (BFO-BT) ceramics were investigated and analyzed. X-ray diffraction measurements suggested a rhombohedral distorted perovskite structure and no structural transformation with the increasing doping content. Rietveld refinement results revealed that (Li_0.5Ga_0.5)²⁺ ions were more susceptible to replace the B-sites and (Li_0.5Er_0.5)²⁺ ions tended to substitute the A-sites. A significant improvement in the dielectric loss, ferroelectricity, and magnetization was observed for both (Li_0.5Ga_0.5)²⁺ and (Li_0.5Er_0.5)²⁺-modified BFO–BT ceramics without the addition of MnO₂ compared to undoped ceramic samples. Remnant magnetization (M_r) of 0.35 emu/g was reached for LG6. The enhanced magnetic properties were related to the suppressed cycloidal spin structure, the presences of the local lattice disorder and the magnetic impurities induced by the (Li_0.5Ga_0.5)²⁺ and (Li_0.5Er_0.5)²⁺ substitution.     

Texture development and dielectric relaxor behavior of 0.80Na0.5Bi0.5TiO3–0.20K0.5Bi0.5TiO3 ceramics templated by plate-like NaNbO3 particles

Plate-like NaNbO₃ particles were used as templates to fabricate grain-oriented 0.96(0.8Na_0.5Bi_0.5TiO₃–0.2 K_0.5Bi_0.5TiO₃)–0.04NaNbO₃ (NKBT) ceramics. The effects of the sintering temperature and the soaking time on the grain orientation and the microstructure of the textured NKBT ceramics were investigated, and the dielectric relaxor behavior is discussed. The results show that textured ceramics were successfully obtained with orientation factor more than 0.8. The textured ceramics have a microstructure with strip-like grains aligning in the direction parallel to the casting plane. The degree of grain orientation increases initially, then decreases with increasing sintering temperature, and increases continuously with increasing soaking time. The textured NKBT ceramics shows obvious dielectric relaxor characteristics which can be well explained by microdomain–macrodomain transition theory with calculating criterion K. The results show that formation of texture is beneficial to microdomain–macrodomain transition, which lead to weaken relaxor behavior and raise the dielectric constant at T_tr.     

Temperature-stable dielectric ceramics based on Na0.5Bi0.5TiO3

Multiple ion substitutions to Na_0.5Bi_0.5TiO₃ give rise to favourable dielectric properties over the technologically important temperature range ?55?°C to 300?°C. A relative permittivity, ε_r,?=?1300?±?15% was recorded, with low loss tangent, tanδ?≤?0.025, for temperatures from 310?°C to 0?°C, tanδ increasing to 0.05 at ?55?°C (1?kHz) in the targeted solid solution (1–x)[0.85Na_0.5Bi_0.5TiO₃–0.15Ba_0.8Ca_0.2Ti_1-yZr_yO₃]–xNaNbO₃: x?=?0.3, y?=?0.2. The ε_r-T plots for NaNbO₃ contents x?<?0.2 exhibited a frequency-dependent inflection below the temperature of a broad dielectric peak. Higher levels of niobate substitution resulted in a single peak with frequency dispersion, typical of a normal relaxor ferroelectric. Experimental trends in properties suggest that the dielectric inflection is the true relaxor dielectric peak and appears as an inflection due to overlap with an independent broad dielectric peak. Process-related cation and oxygen vacancies and their possible contributions to dielectric properties are discussed.     

Enhancement in dielectric and ferroelectric properties of lead free Bi0.5(Na0.5K0.5)0.5TiO3 ceramics by Sb-doping

Lead free piezoelectric Bi_0.5(Na_0.5K_0.5)_0.5TiO₃ (pure and 1 wt.%, 2 wt.%, 4 wt.% Sb-doped) ceramics were synthesized away from its MPB. The crystalline nature of the BNKT ceramic was studied by XRD and SEM. Depolarization temperature (T_d) and transition temperature (T_c) were observed through phase transitions in dielectric studies which were found to increase after Sb-doping, thus increasing its usable temperature range. In the study of relaxation behavior, the activation energy for relaxation was found to be 0.33, 0.43, 0.57 and 0.56 eV for pure and Sb-doped samples, respectively. All samples were found to exhibit normal Curie-Weiss law above their T_c. Doping of Sb was found to restrain the diffused character of the pure sample. In P-E loop, Sb-doping was found to increase the ferroelectric properties.Pure and Sb-doped BNKT ceramics exhibited high values of piezoelectric charge coefficient (d₃₃) as 115, 121, 129 and 100 pC/N, respectively.     

Crystal structure transformation and improved dielectric and magnetic properties of La-substituted BiFeO3 multiferroics

Samples of Bi_1−xLa_xFeO₃ with x = 0.1, 0.3, 0.5, and 0.7 have been synthesized by two stage solid state reaction method. Structural characterization was performed using powder x-ray diffraction at room temperature. The crystal structure of perovskite phases are further characterized via Rietveld analysis which revealed a structural transition from R3c symmetry of the parent phase of BiFeO₃ to orthorhombic Pnma symmetry of LaFeO₃. However the intermediate samples with x = 0.3 and 0.5 are bi – phasic (i.e. a combination of rhombohedral R3c and orthorhombic Pbam phases co-exist). Rietveld Refinement presents a good agreement between measured and simulated patterns. The transition from a rhombohedral to orthorhombic unit cell is suggested to be driven by the dilution of the stereochemistry of the lone pair of Bi³⁺ at A- site. M-H hysteresis loops are recorded at room temperature up to a field of 15 kOe. The G-type antiferromagnetic spin structure and the magnetic moment are very sensitive to increasing La concentration at A-site. La substitution transformed antiferromagnetic BiFeO₃ into ferromagnetic which is closely related to the structural phase transition and modification of antiparallel spin structure. Dielectric constant (ε′) and dissipation factor (tan δ) measured in frequency range 1 kHz to 5 MHz showed dispersion behaviour at low frequencies.     

Complex structural contribution of the morphotropic phase boundary in Na0.5Bi0.5TiO3 - CaTiO3 system

The correlation between structure and dielectric properties of lead-free (1-x)Na_0.5Bi_0.5TiO₃ - xCaTiO₃ ((1-x)NBT - xCT) polycrystalline ceramics was investigated systematically by X-ray diffraction, combined with impedance spectroscopy for dielectric characterizations. The system shows high miscibility in the entire composition range. A morphotropic phase boundary (MPB), at 0.09?≤?x?<?0.15 was identified where rhombohedral and orthorhombic symmetries coexist at room temperature. The fraction of orthorhombic phase increases gradually with x in the MPB region. Dielectric measurements reveal that the relative permittivity increase with addition of Ca²⁺. This behavior is unusual with this kind of doping. A thermal hysteresis occurred only in the MPB composition which varies in a non-monotonically manner with x, detected by dielectric properties. This phenomenon is related to the crystalline microstructure by a linear relationship between the fraction of each phase and dielectric properties, and, more precisely, to the strong interaction between rhombohedral and orthorhombic phases.     

Physical properties of new,lead free (Na0.5Bi0.5)(1−x)BaxTi(1−x)(Fe0.5Nb0.5)xO3 ceramics

This study reports on the synthesis of polycrystalline samples of (Na_0.5Bi_0.5)_(1−x)Ba_xTi_(1−x)(Fe_0.5Nb_0.5)_xO₃ with x=0, 0.025, 0.05, 0.075, and 0.1, using the solid-state reaction technique. It investigates the effects of the substitution of sodium and bismuth by barium in the A site and of titanium by iron and niobium in the B site with regard to the free NBT symmetry and dielectric properties were investigated. The crystallographic and dielectric properties were also investigated. The diffractograms showed that all the samples had a single phase character. The increase of ceramic lattice parameters induced an increase in the size of the perovskite lattice. This increase was caused by the increase of the radii of the A and B sites. Room temperature X-ray data revealed that the ceramic structures underwent a gradual distortion with the increase in the composition fraction. Dielectric permittivity was measured in the temperature range of 120–780 K with frequencies ranging from 1 to 10³ KHz. Three anomalies, namely T_d, T₁ and T_m, were detected and noted to coexist at lower T_d and T_m as the rate of substitutions increased. All the samples exhibited a diffuse phase transition and implied better dielectric permittivity maxima values at temperatures approaching room temperature, since the substitution rate values increased more than that of pure NBT. A relaxor behavior with ΔT_m=14 K and ε'_rmax=3876 at 1 kHz was observed for (Na_0.5Bi_0.5)_0.9Ba_0.1Ti_0.9(Fe_0.5Nb_0.5)_0.1O₃ ceramic.     

Effect of CoFe2O4 mole percentage on multiferroic and magnetoelectric properties of Na0.5Bi0.5TiO3/CoFe2O4 particulate composites

Na_0.5Bi_0.5TiO₃ (NBT), CoFe₂O₄ (CFO) as well as particulate composites containing different mole percentages of NBT and CFO were synthesized by the solid-state sintering route and characterized for their ferroelectric and ferrimagnetic hysteresis loops, magnetostriction and magnetoelectric (ME) output. The mole% of CFO was found to influence the ferroelectric and ferrimagnetic hysteresis loops as well as magnetostriction and piezomagnetic coefficients which in turn had a significant effect on the magnetoelectric voltage coefficient. The highest magnetoelectric voltage coefficient (α) of 0.5 mV/cm/Oe was recorded in (65) NBT–(35) CFO composite.     

Enhanced energy-storage properties of (1-x)(0.7Bi0.5Na0.5TiO3-0.3Bi0.2Sr0.7TiO3)-xNaNbO3 lead-free ceramics

A series of (1-x)(0.7Bi_0.5Na_0.5TiO₃-0.3Bi_0.2Sr_0.7TiO₃)-xNaNbO₃ (BNT-BST-100xNN) lead-free ceramics were fabricated using conventional solid-state reaction technique. The phase behavior, microstructure, dielectric, ac impedance and energy-storage properties of the sintered ceramics were systematically investigated. XRD patterns and surface SEM micrographs revealed the introduction of NaNbO₃ didn't change the perovskite structure of BNT-BST at low doping level. The NaNbO₃ doping gave rise to slimmer P-E loops and thus gained enhanced energy storage properties. Therefore, a maximum energy storage density of 1.03 J/cm³ was achieved at 85 kV/cm at x = 0.01 via increasing the dielectric breakdown strength (DBS). Temperature-dependent dielectric permittivity illustrated the enhanced relaxor characteristics, implying the long-rang ferroelectric order was further damaged due to the introduction of NaNbO₃. The results above indicate the sintered ternary ceramics can be a promising lead-free candidate for energy storage capacitors.     

Solid state metathesis synthesis of BaTiO3, PbTiO3, K0.5Bi0.5TiO3 and Na0.5Bi0.5TiO3

A solid state metathesis approach has been applied to synthesize perovskite oxides such as BaTiO₃, PbTiO₃, K_0.5Bi_0.5TiO₃ and Na_0.5Bi_0.5TiO₃, these were characterized by powder XRD, IR and energy dispersive spectra (EDS). Potassium titanium oxalate and metal chlorides are used as the starting materials. X-ray analysis shows the formation of a single phase with tetragonal structure for BaTiO₃, PbTiO₃, K_0.5Bi_0.5TiO₃ and a monoclinic structure for Na_0.5Bi_0.5TiO₃. The Infrared spectra of these compounds show the characteristic band due to Ti–O octahedron for all the compounds. The EDS spectra show the relative ratio of the metal ions. The morphology of synthesized compounds was obtained from SEM measurements.     

Electrical and photoluminescence properties of Sm3+ doped Na0.5La0.5Bi8-xSmxTi7O27 ceramics

In this study, Sm³⁺ doped Na_0.5La_0.5Bi_8-xSm_xTi₇O₂₇ (NBT-BITL-xSm, x = 0, 0.01, 0.015, 0.02, and 0.03) ceramics were synthesized via a conventional solid-state reaction process. The structural, electrical, and photoluminescence properties of NBT-BITL-xSm ceramics were systematically investigated. The crystal structure of NBT-BITL-xSm was refined using XRD Rietveld refinement and found to possess a single orthorhombic structure at room temperature. Raman spectroscopy revealed that Sm³⁺ ions preferred to substitute for Bi³⁺ located in the A-sites of pseudo-perovskite layers, inducing a slight decrease in orthorhombic distortion. Strong characteristic emission peaks of Sm³⁺ ions were observed in orange-red regions under a 407 nm laser source, and the sample with x = 0.015 achieved the optimal photoluminescent property. Dielectric measurements showed double anomaly permittivity peaks at the temperature of 589 and 600^°C (T_m and T_c, respectively). The complex impedance spectrum indicated that the electrical conductivities mainly originated from crystal grains at high temperature. The activation energy was calculated to be 1.37–1.44 eV from Arrhenius fitting results. After Sm³⁺ substitution, the activation energy for conductivity was increased as a result of reduced oxygen vacancies.     

Structural,magnetic, and dielectric properties in Aurivillius phase SrxBi6-xFe1-x/2Co1-x/2Ti3+xO18

Sr_xBi_6-xFe_1-x/2Co_1-x/2Ti_3+xO₁₈ (x = 0, 0.25, 0.5, 0.75, 1)(SBFCT-x) ceramics were prepared by the sol-gel auto-combustion method, and their microstructures, ferroelectric, magnetic and dielectric properties were investigated. All samples show layer-perovskited Aurivillius phase, which confirms that Sr doping does not affect the structure of SBFCT ceramics. The coexistence of ferroelectricity and ferromagnetism were observed at room temperature for all the samples. The largest remnant polarization (2P_r ˜ 17.4 μC/cm²) is observed in the SBFCT-1 ceramic, while the SBFCT-0.5 ceramic shows the highest remnant magnetization (2M_r ˜ 0.74 emu/g). To explore the effect of valance states of magnetic ions on the properties, we analysed the content variation of Fe²⁺, Co²⁺, and oxygen vacancies by the X-ray photoelectron spectroscopy results. Furthermore, dielectric anomalies have been found around 400 K, which can be ascribed to the hopping process of oxygen vacancies. The effects of Sr and Ti substitution on ferroelectric and magnetic properties have been investigated and discussed.     

Structural investigation and dielectric studies on Mn substituted Pb(Zr0.65Ti0.35)O3 perovskite ceramics

Polycrystalline samples of manganese substituted lead zirconium titanate (PZMT) with general formula Pb(Zr_0.65−xMn_xTi_0.35)O₃ ceramics have been synthesised by high temperature solid state reaction technique. X-ray diffraction (XRD) patterns were recorded at room temperature to study the crystal structure employing Rietveld technique. All the patterns could be refined to R3c space group with rhombohedral symmetry. Bond lengths and angles have been calculated from refined parameters. Microstructural properties of the materials were analysed by scanning electron microscope (SEM) and compositional analysis were carried out by energy dispersive spectrum (EDS) measurements. All the materials exhibit ferroelectric to paraelectric transition. The Curie temperature (T_c) increases with the Mn concentration. We have observed that dielectric constant decreases and AC conductivity increases with the frequency. The correlation between lattice parameters and T_c for the present samples has been observed.     

Piezoelectric properties and microstructures of ZnO-doped Bi0.5Na0.5TiO3 ceramics

This article studies the microstructure and piezoelectric properties of a ceramic lead-free NBT under different amount of ZnO doping. X-ray diffraction shows that Zn²⁺ diffuses into the lattice of (Bi_0.5Na_0.5)TiO₃ to form a solid solution with a pure perovskite structure. By modifying the zinc oxide content, the sintering behavior of (Bi_0.5Na_0.5)TiO₃ ceramics was significantly improved and the grain size was increased. The piezoelectric coefficient d₃₃ for the 1.0 wt.% ZnO-doped (Bi_0.5Na_0.5)TiO₃ ceramics sintered at 1050 °C was found to be 95 pC/N, and the electromechanical coupling factor k_p = 0.13. However, the piezoelectric coefficient d₃₃ for the 0.5 wt.% ZnO-doped (Bi_0.5Na_0.5)TiO₃ ceramics sintered at 1140 °C was found to be 110 pC/N, and the electromechanical coupling factor k_p = 0.17.     

Structural,magnetic, and magnetotransport properties of LaFe0.5Ni0.5O3

The perovskite-type LaFe_0.5Ni_0.5O₃ belonging to the rhombohedral (space group R-3c) crystal structure has been synthesized for which we have identified a magnetic transition at T₁ =?8?K corresponding to the minimum observed in the derivative of temperature dependent magnetization. A bifurcation in the ZFC and FC curves is observed below T₁ that suggests a frustrated magnetic behavior. The non-zero moment above T₁ hints the possibility of the presence of a high-temperature magnetic transition in the material. The resistivity of LaFe_0.5Ni_0.5O₃ evolves as a function of temperature similar to that of a semiconductor. Mott's variable range hopping governs the conduction mechanism of the material. Presence of various anisotropy terms and inhomogeneous magnetic interactions lead to the presence of antiferromagnetic and ferromagnetic interfaces, which eventually causes a magnetic exchange bias and magnetic hysteresis in resistivity. We have also observed direction dependent magnetoresistance in the material.     

Effect of Bi2O3 and B2O3 additives on the sintering temperature, microstructure, and microwave dielectric properties for Sm(Mg0.5Ti0.5)O3 ceramics

The microwave dielectric properties of Sm(Mg_0.5Ti_0.5)O₃ incorporated with various amount of Bi₂O₃ and B₂O₃ additives have been investigated systematically. In this study, both Bi₂O₃ and B₂O₃ additives acting as a sintering aid can effectively lower the sintering temperature from 1550 °C to 1300 °C. The ionic radius of Bi³⁺ for a coordination number of 6 is 0.103 nm, whereas the ionic radius of B³⁺ is 0.027 nm. Clearly, the ionic radius of Bi³⁺ is greatly larger than one of B³⁺, which resulted in the specimens incorporated with Bi₂O₃ having larger lattice parameters and cell volume than those incorporated with B₂O₃. The experimental results show that no second phase was observed throughout the entire experiments. Depending on the interfacial tension, the liquid phase may penetrate the grain boundaries completely, in which case the grains will be separated from one another by a thin layer as shown in Sm(Mg_0.5Ti_0.5)O₃ ceramics incorporated with Bi₂O₃. Whereas, in Sm(Mg_0.5Ti_0.5)O₃ ceramics incorporated with B₂O₃, the volume fraction of liquid is high, the grains may dissolve into the liquid phase, and rapidly rearrange, in which case contact points between agglomerates will be dissolved due to their higher solubility in the liquid, leading plate-like shape microstructure.A dielectric constant (?_r) of 29.3, a high Q × f value of 26,335 GHz (at 8.84 GHz), and a τ_f of −32.5 ppm/°C can be obtained for Sm(Mg_0.5Ti_0.5)O₃ ceramics incorporated with 10 mol% Bi₂O₃ sintered at 1300 °C. While Sm(Mg_0.5Ti_0.5)O₃ ceramics incorporated with 5 mol% B₂O₃ can effectively lower temperature coefficient of resonant frequency, which value is −21.6 ppm/°C. The Sm(Mg_0.5Ti_0.5)O₃ ceramic incorporated with heavily Bi₂O₃ and B₂O₃ additives exhibits a substantial reduction in temperature (∼250 °C) and compatible dielectric properties in comparison with that of an un-doped one. This implied that this ceramic is suitable for miniaturization in the application of dielectric resonators and filters by being appropriately incorporated with a sintering aid.