Phase diagram and properties of Pb(In1/2Nb1/2)O3-Pb(Mg1/3Nb2/3)O3-PbTiO3 polycrystalline ceramics

yPb(In_1/2Nb_1/2)O₃-(1 − x − y)Pb(Mg_1/3Nb_2/3)O₃-xPbTiO₃ (yPIN-(1 − x − y)PMN-xPT) polycrystalline ceramics with morphotropic phase boundary (MPB) compositions were synthesized using columbite precursor method. X-ray diffraction results indicated that the MPB of PIN-PMN-PT was located around PT = 0.33-0.36, confirmed by their respective dielectric, piezoelectric and electromechanical properties. The optimum properties were found for the MPB composition 0.36PIN-0.30PMN-0.34PT, with dielectric permittivity ?_r of 2970, piezoelectric coefficient d₃₃ of 450 pC/N, planar electromechanical coupling k_p of 49%, remanent polarization P_r of 31.6 μC/cm² and T_C of 245 °C. According to the results of dielectric and pyroelectric measurements, the Curie temperature T_C and rhombohedral to tetragonal phase transition temperature T_R-T were obtained, and the “flat” MPB for PIN-PMN-PT was achieved, indicating that the strongly curved MPB in PMN-PT system was improved by adding PIN component, offering the possibility to grow single crystals with high electromechanical properties and expanded temperature usage range (limited by T_R-T).     

Achieving single domain in rhombohedral and tetragonal Mn-doped Pb(In1/2Nb1/2)-Pb(Mg1/3Nb2/3)-PbTiO3 crystals for infrared detecting applications

The [111]-oriented rhombohedral Mn-doped 0.15Pb(In_1/2Nb_1/2)-0.55Pb(Mg_1/3Nb_2/3)O₃-0.30PbTiO₃ (Mn:PIMNT(15/55/30)) crystal and the [001]-oriented tetragonal Mn-doped 0.29Pb(In_1/2Nb_1/2)-0.29Pb(Mg_1/3Nb_2/3)O₃-0.42PbTiO₃ (Mn:PIMNT(29/29/42)) crystal were poled under different conditions. The pyroelectric performance of the two crystals as a function of poling temperature, as well as the relationship with ferroelectric domain configuration and phase structure was investigated systematically. The pyroelectric properties of the two crystals enhance with rising the poling temperature, which can be attributed to the improvement of the single state. And for the rhombohedral Mn:PIMNT(15/55/30) crystal locating near morphotropic phase boundary (MPB), the increase of tetragonal phase induces the deterioration of pyroelectric properties. Due to more residual tetragonal phase, the pyroelectric coefficient of the Mn:PIMNT(15/55/30) crystal poled at 150°C is lower than that poled at 100°C. In general, both the crystals poled above T_C achieve nearly single state, exhibiting the best pyroelectric properties with relatively high Curie temperature (T_C), where P = 9.71 × 10⁻⁴ C m⁻² K⁻¹, F_i = 3.88 × 10⁻¹⁰ m V⁻¹, F_v = 0.068 m² C⁻¹ and F_d = 29.7 × 10⁻⁵ Pa^−1/2 for the rhombohedral Mn:PIMNT(15/55/30) crystal (T_C = 171°C) and P = 6.78 × 10⁻⁴ C m⁻² K⁻¹, F_i = 2.71 ×10⁻¹⁰ mV⁻¹, F_v = 0.1 m² C⁻¹, F_d = 23.54 × 10⁻⁵ Pa^−1/2 for the tetragonal Mn:PIMNT(29/29/42) single crystal (T_C = 251°C), meeting the stable operation of infrared detector at relatively high environmental temperatures.     

Improvement of temperature-stability and piezoelectric performance of Pb(In0.5Nb0.5)O3–PbTiO3 crystals via Nd doping

High-performance relaxor-PbTiO₃ ferroelectric crystals have been widely applied in transduces, sensors and so on. The ferroelectric phase transition temperature restricts their application in automobile, deep oil-well detection and aerospace which requires high thermal stability. Decreasing the effects of ferroelectric phase transition is a promising strategy for improving the thermal stability. Here, the design strategy is structural regulation via rare earth doping tetragonal Pb(In_1/2Nb_1/2)O₃–PbTiO₃ (PIN-PT) crystals. The d₃₃, k₃₃ and T_C of [001]_c-oriented Nd-PIN-PT crystals are 750 pC/N, 87%, 250 °C. Compared with the d₃₃ of tetragonal 0.61PIN-0.39 PT crystals (540 pC/N) and tetragonal 0.35PIN-0.26 Pb(Mg_1/3Nb_2/3)O₃ (PMN)-0.39 PT crystals (530 pC/N), the d₃₃ of Nd-PINT crystals enhance by 39% and 41%. In addition, Nd-PIN-PT crystals have Q_m of 110, which is larger than rhombohedral relaxor-PbTiO₃ ferroelectric crystals (~50). Although the d₃₃ of Nd-PIN-PT crystals is lower than that of rhombohedral relaxor-PT ferroelectric crystals, the d₃₃ and k₃₃ are stable up to 250 °C, which is higher than tetragonal PIN-PMN-PT crystals (210 °C). The high thermal stability of piezoelectric properties is related to the high thermal stability of domain after poling. This work provides a design strategy for high thermal stability ferroelectric crystals.     

Composition-dependent xBa(Zr0.2Ti0.8)O3-(1-x)(Ba0.7Ca0.3)TiO3 bulk ceramics for high energy storage applications

This work reports the composition dependent microstructure, dielectric, ferroelectric and energy storage properties, and the phase transitions sequence of lead free xBa(Zr_0.2Ti_0.8)O₃-(1-x)(Ba_0.7Ca_0.3)TiO₃ [xBZT-(1-x)BCT] ceramics, with x?=?0.4, 0.5 and 0.6, prepared by solid state reaction method. The XRD and Raman scattering results confirm the coexistence of rhombohedral and tetragonal phases at room temperature (RT). The temperature dependence of Raman scattering spectra, dielectric permittivity and polarization points a first phase transition from ferroelectric rhombohedral phase to ferroelectric tetragonal phase at a temperature (T_R-T) of 40?°C and a second phase transition from ferroelectric tetragonal phase - paraelectric pseudocubic phase at a temperature (T_T-C) of 110?°C. The dielectric analysis suggests that the phase transition at T_T-C is of diffusive type and the BZT-BCT ceramics are a relaxor type ferroelectric materials. The composition induced variation in the temperature dependence of dielectric losses was correlated with full width half maxima (FWHM) of A₁, E(LO) Raman mode. The saturation polarization (P_s) ≈8.3?μC/cm² and coercive fields ≈2.9?kV/cm were found to be optimum at composition x?=?0.6 and is attributed to grain size effect. It is also shown that BZT-BCT ceramics exhibit a fatigue free response up to 10⁵ cycles. The effect of a.c. electric field amplitude and temperature on energy storage density and storage efficiency is also discussed. The presence of high T_T-C (110?°C), a high dielectric constant (ε_r ≈?12,285) with low dielectric loss (0.03), good polarization (P_s ≈?8.3?μC/cm²) and large recoverable energy density (W?=?121?mJ/cm³) with an energy storage efficiency (η) of 70% at an electric field of 25?kV/cm in 0.6BZT-0.4BCT ceramics make them suitable candidates for energy storage capacitor applications.     

Temperature-dependent phase transition in [001]C-oriented 0.72Pb(Mg1/3Nb2/3)O3-0.28PbTiO3 single crystals

Temperature-dependent dielectricity and polarization of [001]_C-oriented 0.72Pb(Mg_1/3Nb_2/3)O₃-0.28PbTiO₃ relaxor-based ferroelectric single crystals were studied by using a combined method of the X-ray diffraction, dielectric spectrum, polarization-electric (P-E) field hysteresis loops, and the Landau-phenomenological theory. Results show that the room-temperature rhombohedral phase experiences a rhombohedral-monoclinic-tetragonal coexisting state, then transforms to tetragonal phase, and finally to cubic phase during the zero-field-heating process. The six-order Landau-type thermal expansion parameters for the tetragonal phase were determined by using the typical characteristics at the cubic-tetragonal phase transition in the temperature range from 91 °C to 113 °C. The calculated dielectric curve, polarizations, and P-E loops fit well with the experimental results. The phase stability and piezoelectricity are further studied and compared with those of the PMN-0.36PT single crystal. The provided methods and obtained Landau parameters can be used for further studies on the relaxor-based ferroelectric single crystals.     

High rhombohedral to tetragonal phase transition temperature and electromechanical response in Pb(Yb1/2Nb1/2)O3-Pb(Sc1/2Nb1/2)O3-PbTiO3 ferroelectric system near the morphotropic phase boundary

Relaxor-PT crystals, that is, Pb(Mg_1/3Nb_2/3)O₃-PbTiO₃ (PMN-PT) and Pb(In_1/2Nb_1/2)O₃-Pb(Mg_1/3Nb_2/3)O₃-PbTiO₃ (PIN-PMN-PT), have been used in mechanical to electric energy translation devices, such as for high-frequency imaging and underwater detection. However, low temperature usage remains a problem for high temperature applications, which are restricted by rhombohedral to tetragonal phase temperatures (T _R-T). In this work, we synthesized a new xPb(Yb_1/2Nb_1/2)O₃-yPb(Sc_1/2Nb_1/2)O₃-0.37PbTiO₃ (x = 0.2?0.45) (xPYN-yPSN-0.37 P T) ternary piezoelectric polycrystalline with high T _R-T = 225?245 °C. For 0.45PYN-0.18PSN-0.37 P T ceramics, the piezoelectric coefficient d₃₃, mechanical coupling factors k₃₃, k_p, and k_t, and dielectric coefficients ε_r and T _R-T are on the order of 330 pm/V, 68.3%, 54.3%, 49.3%, 930, and 245 °C, respectively. Thermal piezoelectric and ferroelectric behaviors were investigated in 0.45PYN-0.18PSN-0.37 P T polycrystalline, which are good candidates for high temperature piezoelectric application. DSC curves for xPYN-yPSN-0.37 P T systems present two peaks at 1213 and 1291 °C during the cooling process, showing good crystallization behavior and suitability for single crystal growth.     

High dielectric permittivity and electrostrictive strain in a wide temperature range in relaxor ferroelectric (1-x)[Pb(Mg1/3Nb2/3)O3-PbTiO3]-xBa(Zn1/3Nb2/3)O3 solid solutions

High electric field-induced strain with ultralow hysteresis, which is often generated based on electrostrictive effects in ferroelectric materials, is highly desired due to its potential applications in high-precision displacement actuators. In this paper, (1-x)[Pb(Mg_1/3Nb_2/3)O₃-PbTiO₃]-xBa(Zn_1/3Nb_2/3)O₃ [(1-x)(PMN-PT)-xBZN] ceramics were fabricated by a solid-state reaction method. The effect of Ba(Zn_1/3Nb_2/3)O₃ (BZN) content on dielectric and electrostrictive properties in relaxor ferroelectric PMN-PT solid solutions was investigated in detail by dielectric spectra, polarization-electric field (P-E) hysteresis loops and strain-electric field (S-E) curves. With an increasing BZN content, the temperature stability of the dielectric permittivity of (1-x)(PMN-PT)-xBZN is improved due to the formation of two coexistent phases. A high electrostrictive strain (~0.17% at 60?kV/cm) with an ultralow hysteresis (<10%) characteristic is obtained in a composition where x?=?0.1725. The strain versus polarization (S-P) curves measured from 30?°C to 130?°C can be well fitted based on a quadratic relation, suggesting the dominating role of the electrostrictive effect. The longitudinal electrostrictive coefficient Q₃₃ for this system ranges from 0.0254?m⁴/C² to 0.0318?m⁴/C². Our results suggest that (1-x)(PMN-PT)-xBZN ferroelectric ceramics are potential candidates for applications in capacitors and high-precision displacement actuators.     

Temperature-driven phase transitions and enhanced piezoelectric responses in Ba(Ti0.92Sn0.08)O3 lead-free ceramic

Ferroelectric phases coexistence or transition is an important strategy on generating high piezoelectricity. Here, the temperature-induced phase structural evolution correlated with small signal piezoelectric response d₃₃, bias-field piezoelectric activity d^max₃₃(E), unipolar and bipolar strain piezoelectric outputs d^*₃₃ in Ba(Ti_0.92Sn_0.08)O₃ (BTS0.08) ceramic was investigated in details. Temperature-driven successive phase transitions from rhombohedral (R) to orthorhombic (O), tetragonal (T), finally to cubic (C) phases took place around 14?°C, 38?°C and 61?°C, respectively. The highest d₃₃ value of 675 pC/N is achieved in the T-C phase transition. However, the O-T phase boundary gives the highest d^max₃₃ =?1170?p.m./V, bipolar d^*₃₃ =?822?pm/V and unipolar d^*₃₃ =?1318?pm/V. The temperature-driven phase transition exhibits large enhancements in piezoelectric property comparable to that of composition-induced phase boundary. These features suggest an effective method to design high-performance piezoelectrics by tailoring the types of phase boundary.     

Structure and dielectric behavior of (1-x)Pb(Sc1/2Ta1/2)O3-xPb(In1/2Nb1/2)O3 solid solution

A solid solution system of (1-x)Pb(Sc_1/2Ta_1/2)O₃-xPb(In_1/2Nb_1/2)O₃ (x = 0.2, 0.4, 0.6, and 0.8) was synthesized by conventional solid-state reaction technique. The optimum sintering temperatures of ceramics with x = 0.2, 0.4, 0.6, and 0.8 were 1400?°C, 1400?°C, 1300?°C, and 1200?°C, respectively. At these temperatures, the densest samples and the maximum dielectric constant were obtained. With increasing x, the percentage of pyrochlore phase increased, indicating a decrease in the solubility of solid solution. For x = 0.2, with the sintering temperature increasing, the ordering degree decreased while the dielectric constant increased. For x = 0.6 and 0.8, at the highest sintering temperature, the most pyrochlore phase appeared and the minimum dielectric constant was obtained. In addition, the relaxor characteristics of solid solution ceramics were systematically investigated. It was found that the dielectric maximum decreased and the temperature at dielectric maximum shifted to higher temperature with x increasing. All compositions exhibited the second-order phase transition due to the analysis of dielectric behaviors on heating and cooling. Interestingly, the difference in dielectric maximum between heating and cooling became larger with PIN content increasing. The diffuseness exponents of all compositions were calculated to be in the range of 1.53–1.66, suggesting the typical relaxor. The polarization-electric field (P-E) hysteresis loops of all solid solutions showed the shapes of slim loop. Meanwhile, the coercive field and remnant polarization of all compositions were analyzed in detail.     

Structural and electrical properties of 0.56Pb(Ni1/3Nb2/3)O3-0.10Pb(Zn1/3Nb2/3)O3-0.34PbTiO3 ceramics prepared by different ceramic processings

The ternary system of 0.56Pb(Ni_1/3Nb_2/3)O₃-0.10Pb(Zn_1/3Nb_2/3)O₃-0.34PbTiO₃ (0.56PNN-0.10PZN-0.34PT) ceramics were prepared by conventional solid-state reaction method via straight mixed oxide method, columbite precursor method and B-site oxide mixing route. X-ray diffraction (XRD) measurement demonstrated that both the tetragonal and rhombohedral phases coexist in the B-site oxide mixing route prepared ceramics accompanied by the largest content of perovskite phase of 95.18%. The 0.56PNN-0.10PZN-0.34PT ceramics prepared by the straight mixed oxide method and the B-site oxide mixing route exhibit rather homogeneous microstructure. As a comparison, in the columbite precursor method prepared ceramics nebulous granules and octahedral or other polyhedral morphology grains are observed. All the sintered ceramics exhibit diffused ferroelectric phase transition where the dielectric response peaks are broad, diffused and strongly frequency dependent. However, the temperature of dielectric maximum (T_m) increases greatly from 398.0 K of the 0.56PNN-0.10PZN-0.34PT ceramics prepared by the B-site oxide mixing route to 423.3 K of the ones prepared by the straight mixed oxide method. Saturated and symmetric P-E hysteresis loops are observed in all the sintered ceramics, where the B-site oxide mixing route prepared ceramics exhibit large value of remanent polarization (P_r) of 17.13 μC/cm² and the least value of coercive field (E_c) of 11.99 kV/cm. Piezoelectric constant (d₃₃) exhibits the largest value of 449 pC/N for the ceramics prepared by the B-site oxide mixing route. Such results are related to the phase composition, density and porosity of the ceramics.     

Domain switching and polarization fatigue in rhombohedral PIN-PMN-PT and Mn-doped PIN-PMN-PT single crystals

Domain switching process under alternating electric field was investigated by in situ polarized light microscopy in [001]-oriented Pb(In_1/2Nb_1/2)O₃-Pb(Mg_1/3Nb_2/3)O₃-PbTiO₃ (PIN-PMN-PT) and Mn-doped PIN-PMN-PT single crystals. Only one-step 71° switching was confirmed in pure and Mn-doped PIN-PMN-PT crystals by the formed domain walls, whose projections on the (001) plane are along 45° or 135° with respect to [010] direction. Moreover, polarization and strain loops during cyclic electric field were studied in depth as a function of switching cycles. Polarization fatigue appeared obviously above 1000 bipolar cycles in PIN-PMN-PT samples, while Mn-doped PIN-PMN-PT samples exhibited almost fatigue-free characteristics. By considering the thermodynamic theory, the improved fatigue resistance in Mn-doped PIN-PMN-PT crystals stems from the enhanced energy barrier of domain switching. Mn modification does not affect the domain switching paths, but it can enhance the energy barrier of domain switching, leading to the improved fatigue behaviors. Our results provide a useful insight into the underlying mechanisms between the domain switching process and polarization fatigue for applying high-performance relaxor-ferroelectric single crystals.     

Microwave dielectric properties of ultra-low loss Li2MgTi0.7(Mg1/3Nb2/3)0.3O4 ceramics sintered at low temperature by LiF addition

In this work, ultra-low loss Li₂MgTi_0.7(Mg_1/3Nb_2/3)_0.3O₄ ceramics were successfully prepared via the conventional solid-state method. X-ray photoelectron spectroscopy (XPS), thermally stimulated depolarization current (TSDC) and bond energy were used to determine the distinction between intrinsic and extrinsic dielectric loss in (Mg_1/3Nb_2/3)⁴⁺ ions substituted ceramics. The addition of (Mg_1/3Nb_2/3)⁴⁺ ions enhances the bond energy in unit cell without changing the crystal structure of Li₂MgTiO₄, which results in high Q·f value as an intrinsic factor. The extrinsic factors such as porosity and grain size influence the dielectric loss at lower sintering temperature, while the oxygen vacancies play dominant role when the ceramics densified at 1400?°C. The Li₂MgTi_0.7(Mg_1/3Nb_2/3)_0.3O₄ ceramics sintered at 1400?°C can achieve an excellent combination of microwave dielectric properties: ε_r =?16.19, Q·f?=?160,000?GHz and τ_f =??3.14?ppm/°C. In addition, a certain amount of LiF can effectively lower the sintering temperature of the matrix, and the Li₂MgTi_0.7(Mg_1/3Nb_2/3)_0.3O₄-3?wt% LiF ceramics sintered at 1100?°C possess balanced properties with ε_r?=?16.32, Q·f?=?145,384?GHz and τ_f =??16.33?ppm/°C.     

Dielectric behaviors of Ba(Mg1/3Nb2/3)O3 modified (Na0.5K0.5)NbO3 ceramics

The effects of Ba(Mg_1/3Nb_2/3)O₃ additives to lead-free (1-x)(Na_0.5K_0.5)NbO₃-xBa(Mg_1/3Nb_2/3)O₃ ceramics have been investigated. XRD patterns, SEM images and Raman spectra have been used to discuss phase structure transitions and microstructure. The dielectric behavior has been also investigated by using the empirical law, the Curie-Weiss law and the spin-glass model. Results show the diffused phase transition behavior to be enhanced by increasing Ba(Mg_1/3Nb_2/3)O₃ addition and the dielectric behavior to be changed to the more short range order of relaxor ferroelectric. Barium and Magnesium cations are suggested to enter into the cation sites and induce the changes of lattice structure, microstructure, compositional fluctuation, cation disorder and correlation of neighboring cluster-sized moments.     

Effects of Li2O-B2O3-SiO2 glass on the low-temperature sintering of Zn0.15Nb0.3Ti0.55O2 ceramics

The influences of Li₂O-B₂O₃-SiO₂ glass (LBS) on the activation energy, phase composition, the stability of the structure and microwave dielectric properties of Zn_0.15Nb_0.3Ti_0.55O₂ ceramics have been systematically investigated. LBS glass acted as flux former and contributed to the reactive liquid-phase sintering mechanism, which remarkably lowed the sintering temperature from 1150?°C to 900?°C and enhanced the shrinkage and densification of ceramic at the low sintering temperatures. The ceramics with 1.5?wt% LBS glass sintered at 900?°C for 3?h show great properties: ε_r = 73.59, Q × f = 8024?GHz, τ_f = 270.54?ppm/°C.     

Crystal structure,Raman spectra and microwave dielectric properties of Li2Mg3Ti1-x(Mg1/3Nb2/3)xO6 (0 ≤x ≤ 0.25) ceramics

Li₂Mg₃Ti_1-X(Mg_1/3Nb_2/3)_XO₆ (0?≤x?≤?0.25) ceramics were prepared by a conventional solid-state reaction process. Their crystal structures, sintering characteristics, Raman spectra and microwave dielectric properties were then investigated. XRD patterns of the sintered samples indicated that all compositions showed a single phase and the rock-salt structure. As the (Mg_1/3Nb_2/3)⁴⁺ contents increase, the variations of ε_r values showed a downward trend, which could be explained by the changes of polarizabilities and the shift of Raman vibration modes. Q·f values initially increased to a maximum value and then decreased with increasing of x values. In addition, τ_f values decreased almost linearly with the x values, which significantly correlated with the thermal expansion coefficient. Excellent combined microwave dielectric properties with ε_r =?14.79, Q·f?=?204,900?GHz and τ_f =??18.43?ppm/°C were obtained for Li₂Mg₃Ti_.95(Mg_1/3Nb_2/3)_.05O₆ ceramic sintered at 1550?°C.     

Phase composition,Raman spectra,infrared spectra and dielectric properties of Li2MgTi1-x(Mg1/3Nb2/3)xO4 ceramics at microwave frequency

The Li₂MgTi_1-x(Mg_1/3Nb_2/3)_xO₄ (0?≤x?≤?0.5) ceramics were prepared by the conventional solid-state method. The relationship among phase composition, substitution amount and microwave dielectric properties of the ceramics was symmetrically investigated. All the samples possess the rock salt structure with the space group of Fm-3m. As the x value increases from 0 to 0.5, the dielectric constant linearly decreases from 16.75 to 15.56, which can be explained by the variation of Raman spectra and infrared spectra. The Q·f value shows an upward tendency in the range of 0?≤x?≤?0.3, but it then decreases when x?>?0.3. In addition, the temperature coefficient of resonant frequency (τ_f) is shifted toward zero with the increasing (Mg_1/3Nb_2/3)⁴⁺ addition. By comparison, the Li₂MgTi_0.7(Mg_1/3Nb_2/3)_0.3O₄ ceramics sintered at 1400?°C can achieve an excellent combination of microwave dielectric properties: ε_r=?16.19, Q·f =?160,000?GHz and τ_f =??3.14?ppm/°C.     

Fabrication and characterization of (Pb(Mg1/3Nb2/3)O3, Pb(Yb1/2Nb1/2)O3, PbTiO3) ternary system ceramics

New ternary compositions in the Pb(Mg_1/3Nb_2/3)O₃-Pb(Yb_1/2Nb_1/2)O₃–PbTiO₃ (PMN-PYbN-PT) system were prepared using 0.5Pb(Yb_1/2Nb_1/2)O₃-0.5PbTiO₃ (PYbNT) and (1-x)Pb(Mg_1/3Nb_2/3)O₃–xPbTiO₃ (x = 0.26; PMNT26 or x = 0.325; PMNT32.5) powders synthesized via the columbite method. Dense (≥ 96% of theoretical density) ceramics with PMN/PYbN mole ratios of 25/75 (R-25), 50/50 (R-50) and 75/25 (R-75T and R-75R) were fabricated by reactive sintering at 1000 °C for 4 h. Therefore, incorporation of PYbNT to PMNT successfully decreased sintering temperature of PMNT from 1200 °C-1250 °C to 1000 °C. Samples with higher density and perovskite ratio together with lower weight loss possessed higher dielectric and piezoelectric values in each composition. The R-75 samples had remanent polarization (P_r) values of 34-36 μC/cm² and piezoelectric charge coefficient (d₃₃) of 560 pC/N. The sharp phase transition PMNT as a function of temperature became broader or more diffuse with increasing PYbNT content. However, PYbNT addition to PMNT increased Curie temperature (T_c) from 183 °C (for PMNT32.5) to 220-242 °C (for R-75T and R-75R) to 336 °C (for R-25). Therefore, these ternary compositions can be tailored for various high temperature applications due to the relatively higher T_c with enhanced piezoelectric and dielectric properties as compared to PMNT.     

Anisotropic domain structures of Pb(Mg1/3Nb2/3)O3–PbZrO3–PbTiO3 single crystals with high ferroelectric phase transition temperature

The anisotropic domain structures and local piezoresponse of rhombohedral Pb(Mg_1/3Nb_2/3)O₃–PbZrO₃–PbTiO₃ single crystals with high ferroelectric phase transition temperature (T_FE‐FE≥120°C) were systematically investigated by vector piezoresponse force microscopy. The typical size of labyrinthine domain pattern for [001]_C sample was in the range of 100‐200 nm, revealing its relaxor feature. While the [011]_C sample exhibited ordered ribbon‐shaped domain pattern with preferential alignment along <011> direction since the modulation effect of polar nanoregions. For [111]_C sample, it had messy and featureless domain patterns. For as‐grown crystal, the incorporation of Zr⁴⁺ cation in Pb(Mg_1/3Nb_2/3)O₃–PbTiO₃ system resulted in that the long‐range coulomb interactions of the charged ions in the short range order regions were weakened, leading to an increased relaxor feature. Concurrently, the incorporation of Zr⁴⁺ cation enhanced the Pb‐B repulsion intensity, resulting in an improved T_FE‐FE. Temperature‐dependent properties of as‐grown crystal exhibited good temperature stability from 30 to 120°C, indicating it is a promising material for actuator and ultrasonic transducer applications.     

Composite microstructures and piezoelectric properties in tantalum substituted lead-free K0.5Na0.5Nb1-xTaxO3 ceramics

K_0.5Na_0.5Nb_1-xTa_xO₃ (KNNT) (with x?=?0.00, 0.05, 0.10, 0.20, 0.30, 0.50 and 1) ceramics are prepared by ball milling and two calcinations at 830?°C for 5?h. Subsequent sintering of centimeter size pellets, 1–2?mm thick, is studied using conventional and spark plasma sintering techniques with various conditions. X-Ray diffraction and Raman spectroscopy phase identification reveal orthorhombic to tetragonal phase transitions occurring at about x?=?0.50, associated to chemical disorder. Scanning electron microscope observations and associated energy dispersive X-ray spectroscopy analysis reveal some composite aspect of the ceramics. Substitution of niobium by tantalum, corresponding to x increase, decreases significantly the grain size but also the densification of the ceramics sintered by conventional sintering, while, enhancement of the piezoelectric properties is observed for both sintering techniques. Thanks to parameters optimization of the spark plasma sintering process, temperature-time-pressure, significant improvement of the relative density over 96%, is obtained for all the compositions sintered between 920 and 960?°C, under 50?MPa, for 5–10?min with heating rates of 100?°C/min. High relative permittivity (ε_r =?1027), piezoelectric charge coefficient (d₃₃ =?160 pC/N) and piezoelectric coupling factor (k_p =?46%) are obtained in spark plasma sintered K_0.5Na_0.5Nb_1-xTa_xO₃ composite ceramics, for x ranging between 0.10 and 0.30 and for some specific spark plasma sintering conditions. Thus, tantalum single element substitution on niobium site, combined with spark plasma sintering, is revealed to be a powerful combination for the optimization and the reliability of piezoelectric properties in KNN system.     

Fabrication of 0.24Pb(In1/2Nb1/2)O3-0.42Pb(Mg1/3Nb2/3)O3-0.34PbTiO3 transparent ceramics by conventional sintering technique

0.24Pb(In_1/2Nb_1/2)O₃-0.42Pb(Mg_1/3Nb_2/3)O₃-0.34PbTiO₃ transparent ceramics were fabricated by a conventional sintering technique. Through optimization of sintering conditions of calcination and sintering temperatures and time, the obtained ceramics showed high optical transmittance of 53% and 71% at light wavelengths of 1300 and 2000 nm, respectively. The ceramics showed a rhombohedral to tetragonal phase transition at ~120°C and a tetragonal to cubic phase transition at 222°C. These transition temperatures were higher than those of 0.67Pb(Mg_1/3Nb_2/3)-0.33PbTiO₃ ceramics. In addition, the ceramics had a ferroelectric hysteresis loop, a large piezoelectric constant d₃₃ of 407 pC/N, and a planar electromechanical coupling factor k_p of 52%. These results suggest that the transparent ceramics may be used as a temperature-stable, linear electro-optic material.