Fabrication and photocatalytic performance of Sn-doped titania hollow spheres using polystyrene as template

Sn-doped anatase hollow spheres were fabricated using a template method involving polystyrene spheres as core and anatase coating as shell. The synthesis route included the preparation of PS spheres, followed by their coating by Sn-doped TiO₂ sol-gel precursor and subsequent removal of the PS cores by pyrolysis and recrystallization at 500 °C for 2 h. The observation of minor amounts of rutile suggests that Sn promotes the anatase → rutile phase transformation. At doping levels of ≤ 1.0 mol% Sn, the unsaturated solubility and increasing defect densities enhanced nucleation. At 1.0–2.0 mol% Sn, the solubility remained unsaturated but increasing Sn incorporation reduced crystallinity owing to lattice deformation and partial amorphization. At 2.0–3.0 mol% Sn, solid solution saturation occurred, resulting in excess dopant precipitation, leading to grain boundary pinning and partial blockage of surface-active sites. Ionic radii, thermodynamic, phase equilibria, intervalence charge transfer, and defect chemistry considerations suggest that Sn⁴⁺ exhibits substitutional solid solubility in the TiO₂ lattice. The photocatalytic performance was in the order 1.0 > 1.2 > 1.5 ≈ 0.7 > 2.0 > 0.0 > 3.0 mol% Sn. This ranking is consistent with the dominant role of crystallinity such that, at ≤ 1.0 mol% Sn, the performance increased owing to enhanced nucleation from low defect density and increasing crystallinity while, at 1.0–2.0 mol% Sn, the performance decreased from increased lattice strain and effective partial amorphization, and, at 2.0–3.0 mol% Sn, it decreased from maximal lattice strain and blockage of active sites.     

TiO2 nanofibers doped with rare earth elements and their photocatalytic activity

In the present study rare earth doped (Ln³⁺–TiO₂, Ln = La, Ce and Nd) TiO₂ nanofibers were prepared by the sol–gel electrospinning method and characterized by XRD, SEM, EDX, TEM, and UV-DRS. The photocatalytic activity of the samples was evaluated by Rhodamine 6G (R6G) dye degradation under UV light irradiation. XRD analysis showed that all the synthesized pure and doped titania nanofibers contain pure anatase phase at 500 °C but at 700 °C it shows both anatase and rutile phase. XRD result also shows that Ln³⁺-doped titania probably inhibits the phase transformation. The diameter of nanofibers for all samples ranges from 200 to 700 nm. It was also observed that the presence of rare-earth oxides in the host TiO₂ could decrease the band gap and accelerate the separation of photogenerated electron–hole pairs, which eventually led to higher photocatalytic activity. To sum up, our study demonstrates that Ln³⁺-doped TiO₂ samples exhibit higher photocatalytic activity than pure TiO₂ whereas Nd³⁺-doped TiO₂ catalyst showed the highest photocatalytic activity among the rare earth doped samples.     

Anatase–rutile transformation of TiO2 sol–gel coatings deposited on different substrates

Titanium dioxide is widely used in a lot of applications. The properties of TiO₂ strongly depend on its phase composition. The transformation temperature between phases is influenced by a lot of factors. One of them is a type of substrate under the TiO₂ film. In presented work, thin films of TiO₂ were deposited by the sol–gel method on silicon, stainless steel (304 L) and Co–Cr–Mo alloy (Vitallium). The process of anatase–rutile phase transformation was investigated by Scanning Electron Microscopy (SEM) and X-Ray Diffraction (XRD) studies of deposited coatings. The results were compared with anatase–rutile transformations temperature of TiO₂ powders obtained by analogous sol–gel process. The temperature of anatase–rutile phase transformation changed in the range of 700–1000 °C and strongly depends on a kind of substrate. It was found that anatase–rutile transformation of TiO₂ coating proceeded at a higher temperature than rutilization of titania powders.     

Enhanced photocatalytic activity of electrospun TiO2/ZnO nanofibers with optimal anatase/rutile ratio

The photocatalytic characteristics of the TiO₂/ZnO nanofibers synthesized by electrospinning followed by calcinating at different temperatures to alter the anatase-to-rutile ratio are investigated. The results demonstrate that the photocatalytic activity of TiO₂/ZnO nanofibers is enhanced by optimizing the anatase/rutile ratio among the trade-off effects of the band-gap energy, the electron/hole recombination rate, and the surface area. When calcined at 650 °C, the TiO₂/ZnO nanofibers with optimal anatase/rutile ratio (48:52) balancing these trade-off effects have the highest photocatalytic efficiency both in the degradation of RhB in liquid and conversion of NO gas.     

Decomposition of nonionic surfactant on a nitrogen-doped photocatalyst under visible-light irradiation

A visible-light-active N-containing TiO₂ photocatalysts were prepared from crude amorphous titanium dioxide by heating amorphous TiO₂ in gaseous NH₃ atmosphere. The calcination temperatures ranged from 200 to 1000 °C, respectively. UV–vis/DR spectra indicated that the N-doped catalysts prepared at temperatures <400 °C absorbed only UV light (E_g = 3.3 eV), whereas samples prepared at temperatures ≥400 °C absorbed both, UV (E_g = 3.10–3.31 eV) and vis (E_g = 2.54–2.66 eV) light. The chemical structure of the modified photocatalysts was investigated using FT-IR/DRS spectroscopy. All the spectra exhibited bands indicating nitrogen presence in the catalysts structure. The photocatalytic activity of the investigated catalysts was determined on a basis of a decomposition rate of nonionic surfactant (polyoxyethylenenonylphenol ether, Rokafenol N9). The most photoactive catalysts were those calcinated at 300, 500 and 600 °C. For the catalysts heated at temperatures of 500 and 600 °C Rokafenol N9 removal was equal to 61 and 60%, whereas TOC removal amounted to 40 and 35%, respectively. In case of the catalyst calcinated at 300 °C surfactant was degraded by 54% and TOC was removed by 35%. The phase composition of the most active photocatalysts was as follows: (a) catalyst calcinated at 300 °C—49.1% of amorphous TiO₂, 47.4% of anatase and 3.5% of rutile; (b) catalyst calcinated at 500 °C—7.1% of amorphous TiO₂, 89.4% of anatase and 3.5% of rutile; (c) catalyst calcinated at 600 °C—94.2% of anatase and 5.8% of rutile.     

Photocatalytic Nb2O5-doped TiO2 nanoparticles for glazed ceramic tiles

TiO₂ nanoparticles are currently used as coating for self-cleaning building products. In order to achieve high self-cleaning efficiency for outdoor applications, it is important that titania is present as anatase phase. Moreover, it is desirable that the particle sizes are in nano-range, so that a large enough surface area is available for enhanced catalytic performance. In this work, TiO₂ nanoparticles doped with 0–5 mol% Nb₂O₅ were synthesized by co-precipitation. Nb₂O₅ postponed the anatase to rutile transformation of TiO₂ by about 200 °C, such that after calcination at 700 °C, no rutile was detected for 5 mol% Nb₂O₅-doped TiO₂, while undoped TiO₂ presented 90 wt% of the rutile phase. A systematic decreasing on crystallite size and increasing on specific surface area of TiO₂ were observed with higher concentration of Nb₂O₅ dopant. Photocatalytic activity of anatase polymorph was measured by the decomposition rate of methylene blue under ultraviolet and daylight illumination and compared to commercial standard catalyst (P25). The results showed enhanced catalysis under UV and visible light for Nb₂O₅-doped TiO₂ as compared to pure TiO₂. In addition, 5 mol% Nb₂O₅-doped TiO₂ presented higher photocatalytic activity than P25 under visible light. The enhanced performance was attributed to surface chemistry change associated with a slight shift in the band gap.     

Enhanced photocatalytic activity of porous single crystal TiO2/CNT composites by annealing process

To improve the photocatalytic performance of anatase TiO₂ (a-TiO₂), it is necessary to simultaneously increase its crystallinity and surface area. Our approach to achieve the desired morphology is to develop a porous single crystal that can be transformed from its mesocrystal form via annealing. We synthesized a-TiO₂ mesocrystals onto multiwalled CNTs using a facile one-pot chemical approach, and investigated the effect of the annealing temperature (200–600 °C) on the crystallinity, morphology, chemical bonding state, and photocatalytic performance of the TiO₂/CNT composites. The as-grown sample and sample annealed at 200 °C consisted of spindle-like a-TiO₂ mesocrystals. As the annealing temperature increased to 400 °C, the morphology of a-TiO₂ changed from mesocrystals into porous single crystals and the surface area enlarged due to the thermo-decomposition of organic residues between the subunits. The chemical bonding (Ti–O–C) between TiO₂ and CNT was also strengthened with increasing annealing temperature. On the other hand, the TiO₂ was separated from the CNT at 600 °C because of the large difference in the thermal expansion coefficients. The photocatalytic performance of the TiO₂/CNT composites was the highest at 400 °C due to the increased crystallinity, removal of the by-products, and strengthened Ti–O–C bonds, resulting in an increase in the photocatalytic active sites and efficient charge separation.     

Suspension high velocity oxy-fuel spraying of a rutile TiO2 feedstock: Microstructure,phase evolution and photocatalytic behaviour

Nano-structured TiO₂ coatings were produced by suspension high velocity oxy fuel (SHVOF) thermal spraying using water-based suspensions containing 30 wt% of submicron rutile powders (~180 nm). By changing the flame heat powers from 40 kW to 101 kW, TiO₂ coatings were obtained with distinctive microstructures, phases and photocatalytic behaviour. Spraying with low power (40 kW) resulted in a more porous microstructure with the presence of un-melted nano-particles and a lower content of the anatase phase; meanwhile, high powers (72/101 kW) resulted in denser coatings and rougher surfaces with distinctive humps but not necessarily with a higher content of anatase. Linear sweep voltammetry (LSV) was used to evaluate the photocatalytic performance. Surprisingly, coatings with the lowest anatase content (~20%) using 40 kW showed the best photocatalytic behaviour with the highest photo-conversion efficiency. It was suggested that this was partially owing to the increased specific surface area of the un-melted nano-particles. More importantly, the structural arrangement of the similarly sized TiO₂ nano-crystallites between rutile and antase phases also created catalytic “hot spots” at the rutile−anatase interface and greatly improved the photo-activity.     

Effect of polymer concentration,needle diameter and annealing temperature on TiO2-PVP composite nanofibers synthesized by electrospinning technique

In this study, TiO₂-PVP nanofibers were successfully synthesized on an aluminium collector by using cost-effective electrospinning technique. The nanofibers were prepared at different polymer concentrations, needle diameters and annealing temperatures and properties were studied by various characterizations. The structural properties were studied by X-ray diffraction (XRD) and Raman spectroscopy techniques. Surface morphology and elemental analysis of the samples were investigated by scanning electron microscopy (SEM) attached with energy dispersive spectroscopy (EDS). The optical properties were carried out by UV–Visible absorption spectroscopy (UV–Vis). By varying the polymer concentration and needle diameter, the effect of viscosity and surface tension on the formation of TiO₂-PVP nanofibers was clearly observed by SEM micro images. EDS spectrum shows effective composition of pure TiO₂ nanofibers. XRD peaks observed at temperatures 500 °C, 700 °C and 900 °C confirmed the anatase, mixed and rutile phases of TiO₂ nanofibers respectively. Raman studies also confirmed these phases of TiO₂ nanofibers. The optical band-gap values calculated using Kubelka-Munk function lies in the range of 3.02–3.22 eV.     

Photocatalytic activity of titanium dioxide coatings: Influence of the firing temperature of the chemical gel

Heterogeneous photocatalysis can be exploited for the decomposition of micro-organisms which have developed on the surfaces of building materials. In this work, the efficiency of titanium dioxide coatings on fired clay products is examined. The sol–gel method is used to synthesize a fine TiO₂ powder with a specific surface area of 180 m² g^?1. Thermal treatment of the chemical gel at 340 °C leads to crystallisation in the anatase phase and with further temperature increase, crystallite growth. For thermal treatments in the range 580–800 °C, there is a progressive transition from anatase to rutile. However, despite a decrease in specific surface area of the powder attributed to aggregation/agglomeration, the coherent domain size deduced from X-ray diffraction measurements remains almost constant at 23 nm. Once the transition is completed, increase of thermal treatment temperature above 800 °C leads to further crystallite growth in the rutile phase. The thermally treated titania powders were then sprayed onto fired clay substrates and the photocatalytic activity was assessed by the aptitude of the coating to degrade methylene blue when exposed to ultraviolet light. These tests revealed that the crystallite size is the important controlling factor for photocatalytic activity rather than the powder specific surface area or the anatase/rutile polymorph ratio.     

Enhanced photocatalytic degradation of rutile/anatase TiO2 heterojunction nanoflowers

Rutile/anatase TiO₂ heterojunction nanoflowers were prepared via a facile one-step hydrothermal approach using titanium tetrachloride and urea as the raw materials, cetyl trimethyl ammonium bromide (CTAB) as the template. The prepared TiO₂ nanoflowers were characterized by XRD, SEM, TEM and BET analyses. The photocatalytic performance of the as-prepared TiO₂ samples for methyl blue degradation under simulated solar light was investigated. TiO₂ heterojunction nanoflowers with mixed rutile/anatase phase (prepared with 3 mmol CTAB) give the highest photocatalytic activity. In addition, TiO₂ nanoflowers show excellent stability after 9 cycles under the same conditions. These results suggested that the mixed phase anatase/rutile TiO₂ heterojunction nanoflowers have great potential for the future photodegradation of real dye waste water.     

Synthesis and photocatalysis of TiO2 hollow spheres by a facile template-implantation route

Process variables such as reaction temperature (55 to 90 °C), calcination temperature (450 to 750 °C), and concentration of TiCl₄ precursor (26 to 105 mM) have been examined in order to tailor the surface area, crystallite size, and the anatase/rutile ratio of the polycrystalline TiO₂ microcapsules prepared by a template-implantation route in heptane solvent. The hollow capsules are all non-aggregating with nanoporous shell structure. Among the process variables examined, the Brunauer–Emmett–Teller (BET) surface area and the anatase/rutile ratio are found critically dependent on the reaction temperature, in which a reduced reaction temperature (from 90 to 55 °C) leads to a higher BET value (from 8.4 to 36.4 m^?2 g^?1), a predominant anatase phase (weight fraction of the anatase phase increases from 0.20 to 0.84), and an improved photodegradation of aqueous methylene blue (MB) dye under UV exposure (the degradation rate increases from 0.5×10^?2 to 5.5×10^?2 min^?1).     

Catalytic oxidation of trichloroethylene over TiO2 supported ruthenium catalysts

Different types of TiO₂ (anatase, P25 and rutile) supported ruthenium catalysts were synthesized by wet impregnation and directly reduced in H₂. The distribution characteristics of ruthenium species were thoroughly studied before and after trichloroethylene oxidation. The results show that ruthenium oxide species are very unstable in the anatase phase, but quite stable in the rutile phase of TiO₂. This phenomenon results in different catalytic behaviors for the Ru/TiO₂ catalysts. The Ru/TiO₂ (P25) catalyst has the best catalytic performance among these catalysts. The complete conversion temperature of trichloroethylene is in the temperature range of 260–270 °C.     

Probing the oxidation behavior of Ti2AlC MAX phase powders between 200 and 1000 °C

Oxidation of commercial Ti₂AlC MAX phase powders at 200–1000 °C has been investigated by XRD, XPS, SEM, STA and TGA coupled with FTIR. These powders are a mixture of Ti₂AlC, Ti₃AlC₂, TiC and Ti_1.2Al_0.8. Oxidation at 400 °C led to disappearance of carbide phases from Ti 2p, Al 2p and C 1s XPS spectra. At 600 °C, powders changed from dark grey to light grey with a significant volume increase due to crack formation. Powders were severely oxidized by detecting rutile with minor anatase TiO₂. At 800 °C, α-Al₂O₃ was detected while anatase transformed into rutile TiO₂. The cracks were healed and disappeared. At 1000 °C, the Ti₂AlC powders were fully oxidized into rutile TiO₂ and α-Al₂O₃ with a change of powder color from light grey to yellow. FTIR detected the release of C as CO₂ from 200 °C onwards but with additional CO above 800 °C.     

Microstructure and mechanical properties of Ti(C,N)-based cermets fabricated by in situ carbothermal reduction of TiO2 and subsequent liquid phase sintering

Ti(C,N)-based cermets were prepared by in situ carbothermal reduction of TiO₂ and subsequent liquid phase sintering in one single process in vacuum. The densification behavior, phase transformation, and microstructure evolution of the cermets were investigated by DSC, XRD, SEM, and EDX. The results showed that the carbothermal reduction of TiO₂ was completed below 1250 °C, and Ti(C,N)-based cermets with refined grains were obtained after sintered at 1400 °C for 1 h by this method. The hard phase of the cermets mainly exhibited white core/gray rim structure, in great contrast to the typical black core/gray rim structure of hard phase in traditional cermets. Ti(C,N)-based cermets prepared by this novel method showed excellent mechanical properties with a transverse rupture strength of 2516±55 MPa, a Rockwell hardness of 88.6±0.1 HRA, and a fracture toughness of 18.4±0.7 MPa m^1/2, respectively.     

Functionalizing slag wool fibers with photocatalytic activity by anatase TiO2 and CTAB modification

Anatase TiO₂ coatings prepared by solvothermal process in a neutral ethanol solution of isopropyl titanate at 160 °C have been grown on slag wool fibers (SWF) which were modified by hexadecyltrimethylammonium bromide (CTAB) in advance. X-ray diffraction patterns confirmed the coatings are of a nanocrystalline anatase structure, and scanning electron microscopy observations and energy-dispersive X-ray spectrum revealed a continuous coverage of TiO₂ formed on the fiber surfaces. The photocatalytic activity of the samples was tested by the photocatalytic degradation of methylene blue (MB) solution. The results show that CTAB modified slag wool fibers (CMSWF) are not a suitable adsorbent for MB due to their weaker negative surface charges. Anatase TiO₂ coated CMSWF display higher photocatalyst activity than anatase TiO₂ coated SWF without CTAB modification, and Anatase TiO₂ coated CMSWF are relatively stable under UV-light irradiation.     

Synergy effect in the photocatalytic degradation of methylene blue on a suspended mixture of TiO2 and N-containing carbons

N-containing carbon materials were obtained from waste plum stones submitted to pyrolysis under Ar flow at 700 °C or to activation under steam at 800 °C and enriched with nitrogen by heating in a NH₃/air mixture at 270 °C or in NO at 300 °C. In situ mixtures of TiO₂ and carbons were prepared by the slurry method and methylene blue photodegradation was chosen as a model reaction to verify the influence of N-containing carbons on the photocatalytic activity of TiO₂ under artificial visible light irradiation. From the kinetics of methylene blue degradation an important synergy effect between both solids was detected with a remarkable increase up to a factor of 5.3 higher in the photocatalytic activity on TiO₂–C than that on TiO₂ alone. A mechanism for the photoassisting role of N-containing carbons upon the photoactivity of TiO₂ under visible light is discussed.     

Aluminum titanate based ceramics from aluminum sludge waste

This work aims at obtaining aluminum titanate-based ceramics (Al₂TiO₅: AT) composites from industrial wastes. Al-sludge waste and rutile ore were used as rich sources of alumina and titania instead of pure materials. Sludge-(0–40 wt%) rutile mixtures were mixed, formed and fired at 1350 °C for various times. Phase composition, microstructure, densification, mechanical and thermal behaviors of the obtained AT composites have been investigated. Complete conversion of the starting materials to AT with bulk density of 3.199 g/cm³, compressive strength and modulus of rupture of 326.425 MPa and 30.84 MPa, respectively and very low CTE (−0.927*10⁻⁶ K⁻¹) were achieved by firing the sludge-(30 wt%) rutile at 1350 °C for 4 h. These results suggest that the obtained AT-ceramics from Al-sludge waste-rutile ore are a promising and an ecofriendly route.     

Effects of SiO2 addition on TiO2 crystal structure and photocatalytic activity

A series of TiO₂–SiO₂ mixtures – having the following stoichiometry Ti_1?xSi_xO₂, with x = 0, 0.1, 0.3 and 0.5 atoms per formula unit – were prepared by using precursor oxides and fired at three temperatures (900, 1000 and 1200 °C). The modifications in the structure and, consequently, on the photocatalytic activity, induced by the addition of SiO₂ into the TiO₂ powder, were thoroughly investigated by using various analytical techniques: X-ray powder diffraction, electron microscopy (FE-SEM and TEM), XPS, FT-IR, DRS and BET analysis. The results underlined as essentially no solid solution occurs between the two crystalline end-members. Nevertheless, silica addition caused a retarding effect on anatase-to-rutile phase transformation and on the crystallite growth.The photocatalytic activity of the powders was assessed in gas phase and the results were explained by taking into account the anatase and rutile relative amounts in the samples, their crystallite size, the surface hydroxyl groups adsorbed on the photocatalysts and the surface area of the mixtures.     

Synthesis and photocatalytic performance of hollow sphere particles of SiO2-TiO2 composite of mesocellular foam walls

Hollow Microspheres of SiO₂-TiO₂ photocatalysts whose walls are made up of mesoporous cellular foams were synthesized with the aid of hexane as a swelling agent and P123 as a pore template by an emulsion templating method. Pore structure of materials and crystal phase of titanium oxide was tailored by hydrothermal and calcination temperature during synthesis of samples. The samples were characterized with field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), N₂ adsorption–desorption experiments, X-ray photoelectron spectroscopy (XPS) and X ray diffraction (XRD) techniques. The effect of pore structure and titania phase on photoactivity were evaluated by methylene blue (MB) degradation test under UV light as well. Results showed that hydrothermal temperature during synthesis process has a significant effect on pore and window sizes of mesostructured cellular foam. Interestingly, for the sample hydrothermally treated at higher temperature (130 °C), anatase to rutile transformation was avoided after calcination treatment as high as 800 °C. The highest photocatalytic activity was detected from the sample hydrothermally treated at 130 °C and calcined at 800 °C for which the highest degree of crystallinity and anatase phase as well as enhanced pore connectivity was obtained.