Thermoelectric Properties of NdGd<Subscript>1+<Emphasis Type="Italic">x</Emphasis></Subscript>S<Subscript>3</Subscript> Prepared by CS<Subscript>2</Subscript> Sulfurization

Ternary rare-earth sulfides NdGd_1+x S₃, where 0 ≤ x ≤ 0.08, were prepared by sulfurizing Ln₂O₃ (Ln = Nd, Gd) with CS₂ gas, followed by reaction sintering. The sintered samples have full density and homogeneous compositions. The Seebeck coefficient, electrical resistivity, and thermal conductivity were measured over the temperature range of 300 K to 950 K. All the sintered samples exhibit a negative Seebeck coefficient. The magnitude of the Seebeck coefficient and the electrical resistivity decrease systematically with increasing Gd content. The thermal conductivity of all the sintered samples is less than 1.9 W K⁻¹ m⁻¹. The highest figure of merit ZT of 0.51 was found in NdGd_1.02S₃ at 950 K.     

Preparation and Thermoelectric Properties of LaGd<Subscript>1+<Emphasis Type="Italic">x</Emphasis></Subscript>S<Subscript>3</Subscript> and SmGd<Subscript>1+<Emphasis Type="Italic">x</Emphasis></Subscript>S<Subscript>3</Subscript>

Thermoelectric materials are attractive since they can recover waste heat directly in the form of electricity. In this study, the thermoelectric properties of ternary rare-earth sulfides LaGd_1+x S₃ (x = 0.00 to 0.03) and SmGd_1+x S₃ (x = 0.00 to 0.06) were investigated over the temperature range of 300 K to 953 K. These sulfides were prepared by CS₂ sulfurization, and samples were consolidated by pressure-assisted sintering to obtain dense compacts. The sintered compacts of LaGd_1+x S₃ were n-type metal-like conductors with a thermal conductivity of less than 1.7 W K⁻¹ m⁻¹. Their thermoelectric figure of merit ZT was improved by tuning the chemical composition (self-doping). The optimized ZT value of 0.4 was obtained in LaGd_1.02S₃ at 953 K. The sintered compacts of SmGd_1+x S₃ were n-type hopping conductors with a thermal conductivity of less than 0.8 W K⁻¹ m⁻¹. Their ZT value increased significantly with temperature. In SmGd_1+x S₃, the ZT value of 0.3 was attained at 953 K.     

Thermoelectric Properties of Zintl Compound YbZn<Subscript>2</Subscript>Sb<Subscript>2</Subscript> with Mn Substitution in Anionic Framework

The thermoelectric properties of the Zintl compound YbZn₂Sb₂ with isoelectronic substitution of Zn by Mn in the anionic (Zn₂Sb₂)²⁻ framework have been studied. The p-type YbZn_2−x Mn _x Sb₂ (0.0 ≤ x ≤ 0.4) samples were prepared via melting followed by annealing and hot-pressing. Thermoelectric property measurement showed that the Mn substitution effectively lowered the thermal conductivity for all the samples, while it significantly increased the Seebeck coefficient for x < 0.2. As a result, a dimensionless figure of merit ZT of approximately 0.61 to 0.65 was attained at 726 K for x = 0.05 to 0.15, compared with the ZT of ~0.48 in the unsubstituted YbZn₂Sb₂.     

Thermoelectric Properties of Zr<Subscript>3</Subscript>Mn<Subscript>4</Subscript>Si<Subscript>6</Subscript> and TiMnSi<Subscript>2</Subscript>

The Seebeck coefficient, electrical resistivity, and thermal conductivity of Zr₃Mn₄Si₆ and TiMnSi₂ were studied. The crystal lattices of these compounds contain relatively large open spaces, and, therefore, they have fairly low thermal conductivities (8.26 Wm⁻¹ K⁻¹ and 6.63 Wm⁻¹ K⁻¹, respectively) at room temperature. Their dimensionless figures of merit ZT were found to be 1.92 × 10⁻³ (at 1200 K) and 2.76 × 10⁻³ (at 900 K), respectively. The good electrical conductivities and low Seebeck coefficients might possibly be due to the fact that the distance between silicon atoms in these compounds is shorter than that in pure semiconductive silicon.     

Thermoelectric Properties of SnO<Subscript>2</Subscript> Ceramics Doped with Sb and Zn

Polycrystalline SnO₂-based samples (Sn_0.97−x Sb_0.03Zn _x O₂, x = 0, 0.01, 0.03) were prepared by solid-state reactions. The thermoelectric properties of SnO₂ doped with Sb and Zn were investigated from 300 K to 1100 K. X-ray diffraction (XRD) analysis revealed all XRD peaks of all the samples as identical to the rutile structure, except for the x = 0.03 sample, which had a small amount of Zn₂SbO₄ as a secondary phase. We found that the power factor of the x = 0.03 sample was significantly improved due to the simultaneous increase in the electrical conductivity and the Seebeck coefficient. A power factor value of ∼2 × 10⁻⁴ W m⁻¹ K⁻² was obtained for the x = 0.03 sample at 1060 K, 126% higher than that for the undoped sample.     

Thermoelectric Properties of Co-Doped TiS<Subscript>2</Subscript>

The thermoelectric properties of cobalt-doped compounds Co _x Ti_1−x S₂ (0 ≤ x ≤ 0.3) prepared by solid-state reaction were investigated from 5 K to 310 K. It was found that the electric resistivity ρ and absolute thermopower |S| for all the doped compounds decreased significantly with increasing Co content over the whole temperature range investigated. The increased lattice thermal conductivity of the doped compounds would imply enhancement of the acoustic velocity. Moreover, the ZT value of the doped compounds was improved over the whole temperature range investigated, and specifically reached 0.03 at 310 K for Co_0.3Ti_0.7S₂, being about 66% larger than that of TiS₂.     

Solid-State Synthesis of Te-Doped Mg<Subscript>2</Subscript>Si

Te-doped Mg₂Si (Mg₂Si:Te _m , m = 0, 0.01, 0.02, 0.03, 0.05) alloys were synthesized by a solid-state reaction and mechanical alloying. The electronic transport properties (Hall coefficient, carrier concentration, and mobility) and thermoelectric properties (Seebeck coefficient, electrical conductivity, thermal conductivity, and figure of merit) were examined. Mg₂Si was synthesized successfully by a solid-state reaction at 673 K for 6 h, and Te-doped Mg₂Si powders were obtained by mechanical alloying for 24 h. The alloys were fully consolidated by hot-pressing at 1073 K for 1 h. All the Mg₂Si:Te _m samples showed n-type conduction, indicating that the electrical conduction is due mainly to electrons. The electrical conductivity increased and the absolute value of the Seebeck coefficient decreased with increasing Te content, because Te doping increased the electron concentration considerably from 10¹⁶ cm⁻³ to 10¹⁸ cm⁻³. The thermal conductivity did not change significantly on Te doping, due to the much larger contribution of lattice thermal conductivity over the electronic thermal conductivity. Thermal conduction in Te-doped Mg₂Si was due primarily to lattice vibrations (phonons). The thermoelectric figure of merit of intrinsic Mg₂Si was improved by Te doping.     

Influence of Doping on Structural and Thermoelectric Properties of AgSbSe<Subscript>2</Subscript>

A series of samples with nominal compositions of AgSb_1−x Sn _x Se₂ (with x = 0.0, 0.1, 0.2, and 0.3) and AgSbSe_2−y Te _y (with y = 0.0, 0.25, 0.5, 0.75, and 1.0) were prepared. The crystal structure of both single crystals and polycrystalline samples was analyzed using x-ray and neutron diffractometry. The electrical conductivity, thermal conductivity, and Seebeck coefficient were measured within the temperature range from 300 K to 700 K. In contrast to intrinsic AgSbSe₂, samples doped with Sn and Te exhibit apparent semiconducting properties (E _g = 0.3 eV to 0.5 eV), lower electrical conductivity, and higher values of the Seebeck coefficient for a small amount of Sn (x = 0.1). Further doping leads to decrease of the thermoelectric power and increase of the electrical conductivity. In order to explain electron transport behavior observed in pure and doped AgSbSe₂, electronic structure calculations were performed by the Korringa–Kohn–Rostoker method with coherent potential approximation (KKR–CPA).     

Thermoelectric Properties of In<Subscript>0.3</Subscript>Ga<Subscript>0.7</Subscript>N Alloys

We report on the experimental investigation of the potential of InGaN alloys as thermoelectric (TE) materials. We have grown undoped and Si-doped In_0.3Ga_0.7N alloys by metalorganic chemical vapor deposition and measured the Seebeck coefficient and electrical conductivity of the grown films with the aim of maximizing the power factor (P). It was found that P decreases as electron concentration (n) increases. The maximum value for P was found to be 7.3 × 10⁻⁴ W/m K² at 750 K in an undoped sample with corresponding values of Seebeck coefficient and electrical conductivity of 280 μV/K and 93␣(Ω cm)⁻¹, respectively. Further enhancement in P is expected by improving the InGaN material quality and conductivity control by reducing background electron concentration.     

Thermoelectric Properties of Ca-Filled CoSb<Subscript>3</Subscript>-Based Skutterudites Synthesized by Mechanical Alloying

Ca _z Co_4−x (Fe/Mn) _x Sb₁₂ skutterudites were prepared by mechanical alloying and hot pressing. The phases of mechanically alloyed powders were identified as γ-CoSb₂ and Sb, but they were transformed to δ-CoSb₃ by annealing at 873 K for 100 h. All specimens had a positive Hall coefficient and Seebeck coefficient, indicating p-type conduction by holes as majority carriers. For the binary CoSb₃, the electrical conductivity behaved like a nondegenerate semiconductor, but Ca-filled and Fe/Mn-doped CoSb₃ showed a temperature dependence of a degenerate semiconductor. While the Seebeck coefficient of intrinsic CoSb₃ increased with temperature and reached a maximum at 623 K, the Seebeck coefficient increased with increasing temperature for the Ca-filled and Fe/Mn-doped specimens. Relatively low thermal conductivity was obtained because fine particles prepared by mechanical alloying lead to phonon scattering. The thermal conductivity was reduced by Ca filling and Fe/Mn doping. The electronic thermal conductivity was increased by Fe/Mn doping, but the lattice thermal conductivity was decreased by Ca filling. Reasonable thermoelectric figure-of-merit values were obtained for Ca-filled Co-rich p-type skutterudites.     

Thermoelectric Properties of Sb-Doped Mg<Subscript>2</Subscript>Si<Subscript>0.3</Subscript>Sn<Subscript>0.7</Subscript>

Mg₂(Si_0.3Sn_0.7)_1−y Sb _y (0 ≤ y ≤ 0.04) solid solutions were prepared by a two-step solid-state reaction method combined with the spark plasma sintering technique. Investigations indicate that the Sb doping amount has a significant impact on the thermoelectric properties of Mg₂(Si_0.3Sn_0.7)_1−y Sb _y compounds. As the Sb fraction y increases, the electron concentration and electrical conductivity of Mg₂(Si_0.3Sn_0.7)_1−y Sb _y first increase and then decrease, and both reach their highest value at y = 0.025. The sample with y = 0.025, possessing the highest electrical conductivity and one of the higher Seebeck coefficient values among all the samples, has the highest power factor, being 3.45 mW m⁻¹ K⁻² to 3.69 mW m⁻¹ K⁻² in the temperature range of 300 K to 660 K. Meanwhile, Sb doping can significantly reduce the lattice thermal conductivity (κ _ph) of Mg₂(Si_0.3Sn_0.7)_1−y Sb _y due to increased point defect scattering, and κ _ph for Sb-doped samples is 10% to 20% lower than that of the nondoped sample for 300 K < T < 400 K. Mg₂(Si_0.3Sn_0.7)_0.975Sb_0.025 possesses the highest power factor and one of the lower κ _ph values among all the samples, and reaches the highest ZT value: 1.0 at 640 K.     

Synthesis and Characterization of <Emphasis Type="Italic">p</Emphasis>-Type Pb<Subscript>0.5</Subscript>Sn<Subscript>0.5</Subscript>Te Thermoelectric Power Generation Elements by Mechanical Alloying

A mechanical alloying (MA) process to transform elemental powders into solid Pb_0.5Sn_0.5Te with thermoelectric functionality comparable to melt-alloyed material is described. The room-temperature doping level and mobility as well as temperature-dependent electrical conductivity, Seebeck coefficient, and thermal conductivity are reported. Estimated values of lattice thermal conductivity (0.7 W m⁻¹ K⁻¹) are lower than some reports of functional melt-alloyed PbSnTe-based material, providing evidence that MA can engender the combination of properties resulting in highly functional thermoelectric material. Though doping level and Sn composition have not been optimized, this material exhibits a ZT value >0.5 at 550 K.     

Microstructure and Thermoelectric Properties of AgSbO<Subscript>3</Subscript> Ceramics Prepared by Ion-Exchange Powder Synthesis and Normal Sintering

Silver antimonate (AgSbO₃) is a potential high-temperature thermoelectric oxide with a low thermal conductivity, but it is difficult to fabricate dense bulk material with high phase purity. Well-dispersed AgSbO₃ nanopowder with an average diameter of 50 nm was synthesized by an ion-exchange process in this study, the sintering density of which was apparently enhanced. Nearly single-phase AgSbO₃ ceramic samples with a relative density close to 90% were obtained when sintered at a relatively low temperature (1273 K). The electrical conductivity of AgSbO₃ increased greatly with increasing sintering temperature, probably because of defects originating from the compositional deviation caused by sintering, in addition to increased density. This study also confirmed that AgSbO₃ had a low thermal conductivity, from 1.1 W m⁻¹ K⁻¹ at room temperature to 0.8 W m⁻¹ K⁻¹ at 673 K.     

Effects of Ca and Mn Additions on the Microstructure and Dielectric Properties of (Bi<Subscript>0.5</Subscript>Na<Subscript>0.5</Subscript>)TiO<Subscript>3</Subscript> Ceramics

Dielectric ceramics based on the solid solution (1 − x)Bi_0.5Na_0.5TiO₃ (BNT)-xCaTiO₃ (CT) were synthesized by the conventional solid-state route. BNT with various contents of CT formed a complete solid solution and exhibited a rhombohedral structure. CT in this solid solution with BNT was observed to decrease the dielectric constant at higher temperatures and raise the dielectric constant at lower temperatures. On the other hand, decreased ferroelectricity was observed with increasing CT concentration, resulting in a downward shift of the depolarization temperature and a decrease of the dissipation factor. With the addition of Mn²⁺ to 0.86BNT-0.14CT, the temperature characteristics of capacitance were improved (−55°C to 250°C, ΔC/C _25°C ≤ ±15%). By doping with 1.5 wt.% Mn²⁺, the dielectric constant at room temperature reached over 900, with a dielectric loss of less than 1%.     

Thermoelectric Properties of Co<Subscript>4</Subscript>Sb<Subscript>12</Subscript> Skutterudite Materials with Partial In Filling and Excess In Additions

The properties of Co₄Sb₁₂ with various In additions were studied. X-ray diffraction revealed the presence of the pure δ-phase of In_0.16Co₄Sb₁₂, whereas impurity phases (γ-CoSb₂ and InSb) appeared for x = 0.25, 0.40, 0.80, and 1.20. The homogeneity and morphology of the samples were observed by Seebeck microprobe and scanning electron microscopy, respectively. All the quenched ingots from which the studied samples were cut were inhomogeneous in the axial direction. The temperature dependence of the Seebeck coefficient (S), electrical conductivity (σ), and thermal conductivity (κ) was measured from room temperature up to 673 K. The Seebeck coefficient of all In-added Co₄Sb₁₂ materials was negative. When the filler concentration increases, the Seebeck coefficient decreases. The samples with In additions above the filling limit (x = 0.22) show an even lower Seebeck coefficient due to the formation of secondary phases: InSb and CoSb₂. The temperature variation of the electrical conductivity is semiconductor-like. The thermal conductivity of all the samples decreases with temperature. The central region of the In_0.4Co₄Sb₁₂ ingot shows the lowest thermal conductivity, probably due to the combined effect of (a) rattling due to maximum filling and (b) the presence of a small amount of fine-dispersed secondary phases at the grain boundaries. Thus, regardless of the non-single-phase morphology, a promising ZT (S ² σT/κ) value of 0.96 at 673 K has been obtained with an In addition above the filling limit.     

Thermal Conductivity of Bi<Subscript>0.5</Subscript>Sb<Subscript>1.5</Subscript>Te<Subscript>3</Subscript> Affected by Grain Size and Pores

A fine measurement system for measuring thermal conductivity was constructed. An accuracy of 1% was determined for the reference quartz with a value of 1.411 W/m K. Bi_0.5Sb_1.5Te₃ samples were prepared by mechanical alloying followed by hot-pressing. Grain sizes were varied in the range from 1 μm to 10 μm by controlling the sintering temperature in the temperature range from 623 K to 773 K. The thermal conductivity was 0.89 W/m K for the sample sintered at 623 K, while a grain size of 1.75 μm was measured by optical microscopy and scanning electron microscopy. The thermal conductivity increased on the sample sintered at 673 K because of grain growth and decreased on those sintered at the temperatures from 673 K to 773 K because the increase of pore size caused to decrease thermal conductivity. The increase of thermal conductivity for the samples sintered at temperatures above 773 K was affected by the increase of carrier concentration.     

Effects of Ir Substitution and Processing Conditions on Thermoelectric Performance of p-Type Zr0.5Hf0.5Co1?xIrxSb0.99Sn0.01 Half-Heusler Alloys

A series of samples with the composition Zr_0.5Hf_0.5Co_1−x Ir _x Sb_0.99Sn_0.01 (x = 0.0 to 0.7) were synthesized by high-temperature solid-state reaction at 1173 K. High-density pellets of the powders were obtained using hot press (HP) and spark plasma sintering (SPS) techniques. The thermoelectric properties of the pellets were measured from 300 K to 750 K. Independently of the pressing conditions, all Ir-containing samples (x > 0) showed p-type semiconducting behavior. At 300 K, the electrical conductivity and thermopower of Zr_0.5Hf_0.5Co_1−x Ir _x Sb_0.99Sn_0.01 materials surprisingly increased with increasing Ir concentration. The largest electrical conductivity and thermopower values of 150 S/cm and 140 μV/K, respectively, were observed at 300 K for x = 0.7. The thermal conductivity of the synthesized materials decreased with increasing Ir content, went through a minimum value (x = 0.3), and increased thereafter with further addition of Ir. Pellets fabricated by SPS showed smaller thermal conductivity than pellets of the same composition obtained from uniaxial hot pressing. A thermal conductivity value of ∼2.0 W/m K was observed at 300 K for an SPS pellet with the com- position Zr_0.5Hf_0.5Co_0.5Ir_0.5Sb_0.99Sn_0.01. The thermal conductivity of Zr_0.5Hf_0.5- Co_1−x Ir _x Sb_0.99Sn_0.01 decreased with rising temperature, and the smallest value of ∼1.5 W/m K was observed at 750 K for the SPS specimen with x = 0.5.     

Thermoelectric Properties of Ag-doped Mg<Subscript>2</Subscript>Ge Thin Films Prepared by Magnetron Sputtering

Silver doped p-type Mg₂Ge thin films were grown in situ at 773 K using magnetron co-sputtering from individual high-purity Mg and Ge targets. A sacrificial base layer of silver of various thicknesses from 4 nm to 20 nm was initially deposited onto the substrate to supply Ag atoms, which entered the growing Mg₂Ge films by thermal diffusion. The addition of silver during film growth led to increased grain size and surface microroughness. The carrier concentration increased from 1.9 × 10¹⁸ cm⁻³ for undoped films to 8.8 × 10¹⁸ cm⁻³ for the most heavily doped films, but it did not reach saturation. Measurements in the temperature range of T = 200–650 K showed a positive Seebeck coefficient for all the films, with maximum values at temperatures between 400 K and 500 K. The highest Seebeck coefficient of the undoped film was 400 μV K⁻¹, while it was 280 μV K⁻¹ for the most heavily doped film at ∼400 K. The electrical conductivity increased with silver doping by a factor of approximately 10. The temperature effects on power factors for the undoped and lightly doped films were very limited, while the effects for the heavily doped films were substantial. The power factor of the heavily doped films reached a non-optimum value of ∼10⁻⁵ W cm⁻¹ K⁻² at 700 K.     

Effect of Ce-Doping on Thermoelectric Properties in PbTe Alloys Prepared by Spark Plasma Sintering

Ce-doped Pb_1−x Ce _x Te alloys with x = 0, 0.005, 0.01, 0.015, 0.03, and 0.05 were prepared by induction melting, ball milling, and spark plasma sintering techniques. The structure and thermoelectric properties of the samples were investigated. X-ray diffraction (XRD) analysis indicated that the samples were of single phase with NaCl-type structure for x less than 0.03. The lattice parameter a increases with increasing Ce content. The lower Ce-doped samples (x = 0.005 and 0.01) showed p-type conduction, whereas the pure PbTe and the higher doped samples (x = 0, 0.015, 0.03, and 0.05) showed n-type conduction. The lower Ce-doped samples exhibited a much higher absolute Seebeck coefficient, but the higher electrical resistivity and higher thermal conductivity compared with pure PbTe resulted in a lower figure of merit ZT. In contrast, the higher Ce-doped samples exhibited a lower electrical resistivity, together with a lower absolute Seebeck coefficient and comparable thermal conductivity, leading to ZT comparable to that of PbTe. The lowest thermal conductivity (range from 0.99 W m⁻¹ K⁻¹ at 300 K to 0.696 W m⁻¹ K⁻¹ at 473 K) was found in the alloy Pb_0.95Ce_0.05Te due to the presence of the secondary phases, leading to a ZT higher than that of pure PbTe above 500 K. The maximum figure of merit ZT, in the alloy Pb_0.95Ce_0.05Te, was 0.88 at 673 K.     

Thermoelectric Properties of <Emphasis Type="Italic">p</Emphasis>-Type Mg<Subscript>2.00</Subscript>Si<Subscript>0.25</Subscript>Sn<Subscript>0.75</Subscript> with Li and Ag Double Doping

Mg₂Si_1−x Sn _x -system solid solutions are ecofriendly semiconductors that are promising materials for thermoelectric generators in the middle temperature range. To produce a thermoelectric device, high-performance p- and n-type materials must be balanced. In this paper, p-type Mg_2.00Si_0.25Sn_0.75 with Li and Ag double doping was prepared by the liquid–solid reaction method and hot-pressing. Effects of Li and Ag double doping on thermoelectric properties were investigated in the temperature range from room temperature to 850 K. All sintered compacts were identified as single-phase solid solutions with anti-fluorite structure. The carrier concentration increased with the double doping. The temperature dependence of resistivity of the double-doped samples was similar to that of a metal. The seebeck coefficient increased with temperature to a maximum value and then decreased in the intrinsic region. Thermal conductivity decreased linearly with increasing temperature, reaching a minimum near the intrinsic region, and then increased rapidly because of the contribution of the bipolar component. The dimensionless figure of merit reached 0.32 at 610 K for Mg_2.00Si_0.25Sn_0.75 double-doped with Li-5000 ppm and Ag-20000 ppm.