Smart NMR Method of Measurement of Moisture Content of Vegetables During Microwave Vacuum Drying

Microwave drying is usually combined with vacuum environment in conjunction with hot air flow to draw the moisture rapidly. The moisture content of the vegetables undergoing drying is hard to measure online. This research designed a microwave vacuum drying (MVD)-low-field nuclear magnetic resonance (NMR) smart device and investigated the feasibility of NMR method for online measurement of state of moisture during MVD. The relation between the signal amplitude (A ₂) and the true moisture content (M ₁) of six kinds of vegetables (mushroom, carrot, potato, lotus, edamame, vegetable corn) was fitted to estimate if NMR can measure the M ₁ of vegetables directly. Results showed that A ₂ and M ₁ of different fresh vegetables had no single empirical mathematical model to fit. However, for each kind of these vegetables, the A ₂ and corresponding M ₁ in different MVD stages showed a significant linear relationship. The predicted moisture content (M ₂) of mushroom: M ₂ = 5.25351 × 10^?4 A ₂ ? 0.34042, R = 0.996; carrot: M ₂ = 5.78756 × 10^?4 A ₂ ? 0.14108, R = 0.998; potato: M ₂ = 3.10019 × 10^?4 A ₂ ? 0.10612, R = 0.991; lotus: M ₂ = 2.32415 × 10^?4 A ₂ ? 0.01573, R = 0.998; edamame: M ₂ = 3.13310 × 10^?4 A ₂ ? 0.4198, R = 0.996; vegetable corn: M ₂ = 1.69461 × 10^?4 A ₂ ? 0.09063, R = 0.995. The linear models between M ₂ and A ₂ were able to estimate the end point (M ₁ < 8%) of MVD with a high accuracy (P > 0.950).     

Intermittent and Continuous Microwave-Convective Air-Drying Characteristics of Sage (<Emphasis Type="Italic">Salvia officinalis</Emphasis>) Leaves

The effect of microwave-convective air-drying (continuous and intermittent) and convective air-drying of sage (Salvia officinalis) on color and essential oil content were studied. For microwave-convective air-drying, four pulse ratio levels (PR1, PR2, PR3, and PR4) at 25 °C drying air temperature were used and the average drying rates were 0.404, 0.158, 0.114, and 0.085 kg H₂O kg^?1 DM min^?1 for PR1, PR2, PR3, and PR4, respectively. For convective air-drying, two drying temperatures of 40 and 50 °C were examined and the average drying rates were 0.005 and 0.006 kg H₂O kg^?1 DM min^?1 for 40 and 50 °C, respectively. The experimental data were fitted to 11 different moisture ratio models to describe the drying kinetics under various drying conditions. Page model was found satisfactory to describe the drying curves of sage leaves. Comparing with the fresh sage, lightness (L*), greenness, and yellowness decreased for all drying applications. Lightness, greenness, and yellowness of the convective air-dried sage leaves were higher than those of microwave-convective air-dried sage leaves. The deviation from fresh product color (ΔE*) increased as the pulse ratio or the drying air temperature increased. The total quantity of essential oils of sage decreased considerably during microwave-convective air-drying whereas the loss of essential oils was limited during air-drying.     

A Case Study on Optimization of Biomass Flow During Single-Screw Extrusion Cooking Using Genetic Algorithm (GA) and Response Surface Method (RSM)

In the present study, response surface method (RSM) and genetic algorithm (GA) were used to study the effects of process variables like screw speed, rpm (x ₁), L/D ratio (x ₂), barrel temperature (°C; x ₃), and feed mix moisture content (%; x ₄), on flow rate of biomass during single-screw extrusion cooking. A second-order regression equation was developed for flow rate in terms of the process variables. The significance of the process variables based on Pareto chart indicated that screw speed and feed mix moisture content had the most influence followed by L/D ratio and barrel temperature on the flow rate. RSM analysis indicated that a screw speed?>?80 rpm, L/D ratio?>?12, barrel temperature?>?80 °C, and feed mix moisture content?>?20% resulted in maximum flow rate. Increase in screw speed and L/D ratio increased the drag flow and also the path of traverse of the feed mix inside the extruder resulting in more shear. The presence of lipids of about 35% in the biomass feed mix might have induced a lubrication effect and has significantly influenced the flow rate. The second-order regression equations were further used as the objective function for optimization using genetic algorithm. A population of 100 and iterations of 100 have successfully led to convergence the optimum. The maximum and minimum flow rates obtained using GA were 13.19?×?10^?7 m³/s (x ₁?=?139.08 rpm, x ₂?=?15.90, x ₃?=?99.56 °C, and x ₄?=?59.72%) and 0.53?×?10^?7 m³/s (x ₁?=?59.65 rpm, x ₂?=?11.93, x ₃?=?68.98 °C, and x ₄?=?20.04%).     

Development and characterization of reconstituted hydrogel from <Emphasis Type="Italic">Aloe vera</Emphasis> (<Emphasis Type="Italic">Aloe barbadensis</Emphasis> Miller) powder

Structural and rheological characterization of reconstituted hydrogels developed from A. vera non-fibrous alcohol insoluble residue (NFAIR) powder using different methods [viz., shaking (S), heating-shaking (HS), and heating (H)] and concentrations (viz., 0.2–1.6 %, w/v) was carried out. Functional group distribution by FTIR spectroscopy and Congo red (CR) method revealed the presence of acetylated acemannan in A. vera powder. Dynamic oscillation studies of A. vera (NFAIR) fluids at all concentrations of 0.2–1.6 %, w/v, showed gel strength in the order of H > HS > S method. However, in H method, increase in concentration from 0.2 to 1.6 %, w/v showed the conformational transition from semi-diluted solution to weak gel nature. Rheological models described the effect of heating temperatures (HT); 30–90 °C, and times (Ht); 15–60 min on viscoelastic behavior in reconstituted A. vera fluids. The reconstituted A. vera hydrogel prepared with a concentration of 1.6 %, w/v using 50 °C (HT) and 30 min (Ht) condition showed a good agreement with the Power law (storage modulus, G′) and Weak gel model (complex modulus, G*) fitted data (R² > 0.94) resulting higher viscoelastic moduli intercepts; G′₀ (71.5 Pa s ^n′), G″₀ (33.5 Pa s ^n″), lower slopes; n′ (0.22), n″ (0.06), higher network strength (A _F , 121.3 Pa s^1/z ) and number of network (z, 5.3) values. The obtained results suggested that heating at 50 °C/30 min can develop aqueous weak gel networks of A. vera with enhanced gel strength which may be utilized as a novel gelling agent for wide variety of targeted applications in food and pharmaceutical sectors.     

Thermal transition and thermo-physical properties of potato (<Emphasis Type="Italic">Solanum tuberosum L</Emphasis>.) var. Russet brown

Potatoes are an important food in many regions of the world and are commonly used in a variety of food products. Thermal transition and thermo-physical properties of potatoes are important in order to design efficient food processes and select appropriate storage conditions. In this study, we determined the thermal transitions and thermophysical properties of raw and blanched/par-fried potato for a temperature range of ??32 to 21.1 °C. Using differential scanning calorimetry, we found an initial freezing point (T_f) at ??1.8?±?0.1 °C, an onset of melting (T_m^′) at ??9.9?±?0.2 °C and an unfreezable water content (X^′_w) for maximally freeze-concentrated raw potato at 0.21 kg water/kg potato. Corresponding values for blanched/par-fried potatoes were ??0.9?±?0.1 °C, ??11.0?±?0.2 °C and 0.18 kg water/kg potato. Results show that an increase in solids content decreased T_f of both raw and blanched potatoes. We modelled the relationship between them using the Chen model. The apparent specific heat (C_app) increased around T_f to 31.7?±?1.13 kJ/kg K for raw potato and 26.7?±?0.62 kJ/kg K for blanched/par-fried potato. For frozen raw potato at ??32 °C, thermal diffusivity (α) was 0.89?±?0.01?×?10?^?6 m²/s and thermal conductivity (k), 1.82?±?0.14 W/m K, respectively. These values were higher for frozen raw potato than for the unfrozen raw potato (0.15?±?0.01?×?10?^?6 m²/s and 0.56?±?0.08 W/m K, respectively at 21.1 °C). The apparent density (ρ) of frozen raw potato (992?±?4.00 kg/m³ at ??32 °C) was less than that for unfrozen raw potato (1053?±?4.00 kg/m³ at 21.1 °C), and a similar trend was obtained for blanched/par-fried potato (993?±?2.00 kg/m³ at ??32 °C and 1188?±?7.00 kg/m³ at 21.1 °C, respectively). This study established a correlation between thermo-physical properties and temperature. Findings may be used to inform the design and optimization of freezing processes and frozen storage for potato products.     

Modeling the Inactivation of <Emphasis Type="Italic">Listeria innocua</Emphasis> and <Emphasis Type="Italic">Escherichia coli</Emphasis> in Fresh-Cut Tomato Treated with Pulsed Light

The effectiveness of pulsed light (PL) treatments to inhibit microorganisms on fresh-cut tomatoes (Lycopersicon esculentum Mill., cv. Daniela) was investigated. Tomato slices inoculated with Escherichia coli or Listeria innocua were exposed to PL treatments (4, 6, or 8 J cm^?2 fluence) and kept cold at 4 °C for 20 days. L. innocua and E. coli counts, gases in the headspace of the containers (O₂ and CO₂), pH, titratable acidity, and soluble solid content were monitored throughout the cold storage. The PL treatments reduced significantly (p < 0.05) initial loads of both microbes. The effect of the PL fluence on the survival number of microoganisms was described by a log-linear model (R ² = 0.849–0.999). At any fixed time within the cold storing, the microbial counts for untreated samples were always higher than those cut tomatoes that had been previously PL-treated. The behavior of L. innocua and E. coli during the storage were well adjusted (R ² > 0.930) by Gompertzian models; the studied microorganisms exhibited different patterns during the storage period. On the other hand, O₂ and CO₂ partial pressures in containers with fresh-cut tomatoes were also significantly affected by PL treatments (p < 0.05). The highest PL fluence caused the greatest changes of O₂ and CO₂ contents. In addition, the application of PL triggered an acceleration of the O₂ consumption during the cold stage. PL treatments might be used to effectively extend the safety of fresh-cut tomatoes over 12 days of storage against E. coli and L. innocua growth.     

Antioxidant Activity and Determination of Phenolic Compounds from <Emphasis Type="Italic">Eugenia involucrata</Emphasis> DC. Fruits by UHPLC-MS/MS

Fruits have been the focus of several studies aimed at finding new antioxidant sources for protection against the damage caused by reactive species. In this study, the antioxidant activity and the presence of phenolic compounds in all parts (peel, pulp, and seeds) of Eugenia involucrata DC. fruits were evaluated. DPPH^·, ABTS^·+, and ORAC methods were used to determine the antioxidant activity, and an UHPLC-MS/MS method was developed for determining the phenolic compounds (gallic, chlorogenic, ferulic, p-coumaric and ellagic acids, quercetin, and myricetin). In the determination of both antioxidant activity and phenolic composition, the efficiency of solvents with different polarities—methanol/H₂O (80:20, v/v), ethanol/H₂O (80:20, v/v), methanol/acidified water with phosphoric acid pH 3.00 (80:20, v/v), and ethyl acetate—for the extraction of the phenolic compounds, was also evaluated. All parts of E. involucrata fruits showed antioxidant activity, in the range of 36.68 ± 1.44 to 873.87 ± 18.24 μmol TE g^?1, being the highest values found in the seeds and peel when more polar extraction solvents were used. Six, five, and three phenolic compounds were identified and quantified in the pulp, peel, and seeds, respectively, with the highest abundance as p-coumaric acid (14 ± 2 mg kg^?1) in the pulp, quercetin (47 ± 5 mg kg^?1) in the peel, and gallic acid (74 ± 4 mg kg^?1) in the seeds, also when more polar solvents were used. Although antioxidant activity methods suggested that the peel and seeds have more antioxidant potential, a wider variety of compounds were determined in the pulp.     

Non-destructive Assessment of Guava (<Emphasis Type="Italic">Psidium guajava</Emphasis> L.) Maturity and Firmness Based on Mechanical Vibration Response

Storage potential and eating quality of guava (Psidium guajava L.) fruit depend on its maturity. Segregation of guava according to maturity and firmness measured using non-destructive technologies would help the industry to designate ripe fruit to immediate market and less ripe fruit for distant market (e.g., exportation). This research was conducted to evaluate the potential of experimental resonant frequency (f _e) and elasticity index (EI) to estimate fruit firmness, which has been reported to be inversely correlated to its maturity. A maturity index (I _m) was calculated as the ratio of total soluble solids/titratable acidity (TSS/TA). It was proved that TSS, TA, and I _m were significantly correlated (P?<?0.05) to skin firmness (F _s), flesh firmness (F _f), stiffness (S), and analytical resonant frequency (ω _n ), being S the attribute best fitted to I _m (R ²?=?0.77). Since it was observed that f _e and EI were sensitive to changes in fruit firmness, both of them were explored as alternatives to predict F _s, F _f, S, and ω _n of guava fruit. In some cases, EI improved the models to predict guava firmness traits (e.g., F _s vs f _e had a coefficient of determination of R ²?=?0.58, whereas for F _s vs EI, it was R ²?=?0.62). The best model occurred when plotting ω _n vs f _e (R ²?=?0.86), followed by S vs EI (R ²?=?0.84), making these promising features for the development of a new practical application using frequency response measurement as a non-destructive method to assess guava maturity.     

Effect of Thermosonic Pretreatment and Microwave Vacuum Drying on the Water State and Glass Transition Temperature in <Emphasis Type="Italic">Agaricus bisporus</Emphasis> Slices

This study aimed to understand the micromechanism of thermosonic pretreatment and microwave vacuum drying on Agaricus bisporus. The water state and glass transition temperature (T _g ) of fresh and thermosonically treated Agaricus bisporus slices during microwave vacuum drying were studied using differential scanning calorimetry (DSC), low-field nuclear magnetic resonance (LF-NMR), and magnetic resonance imaging (MRI). Results showed that four population groups were contained in the initial distribution of transverse relaxation time (T ₂) data of fresh A. bisporus slices: T ₂₁ (0.38–7.05 ms), T ₂₂ (9.33–32.75 ms), T ₂₃₁ (37.65–265.61 ms), and T ₂₃₂ (305.39–811.13 ms). Thermosonic pretreatment significantly decreased the initial free water content of A. bisporus sample but was accompanied by a sharp increase in its immobilized water. “Semi-bound water transfer” appeared during microwave vacuum drying (MVD) at moisture contents (X _w ) of 0.70 and 0.60 g/g (wet basis (w.b.)) for untreated and thermosonically treated samples, respectively. MVD caused dramatic changes in the water state and enhanced the T _g by decreasing the content and mobility of immobilized water in A. bisporus tissues. The mobility of semi-bound water for thermosonically and MVD-treated samples was higher than for MVD-untreated samples, resulting in T _g values decreasing by approximately 2–11.5 °C, but the uniformity of water distribution in thermosonic-treated and MVD-treated samples was better at X _w  ≤ 0.52 g/g (w.b.).     

Steady- and Unsteady-State Determination of the Water Vapor Permeance (<Emphasis Type="Italic">WVP</Emphasis>) of Polyethylene Film to Estimate the Moisture Gain of Packed Dry Mango

The water vapor permeance (WVP; g m^?2 d^?1 Pa^?1) of packaging films quantifying the water vapor transfer rate between foods and its surroundings is usually determined in units operating under steady-state conditions that do not necessarily reflect food handling scenarios. This study evaluated the determination of the WVP of a polyethylene (PE) film by steady-state method ASTM F1249-06 using a permeability cell and unsteady-state method ASTM E96/E96M in which 102 vacuum-sealed PE bags containing silica gel were stored (37.8 °C, 75% relative humidity) and weighed over 25 days. Average steady-state WVP (2.935 ± 0.365 × 10^?3, n = 4) fell within the 95% quantiles of unsteady-state WVP values (1.818–3.183 × 10^?3, n = 2142). Moisture uptake of dehydrated mango stored at 37.8 °C and 75% relative humidity was predicted with WVP values obtained by both methods. Predictions were validated by monitoring over 25 days the weight gain of 100 PE bags with dry mango. Experimental moisture averages during storage fell within one standard deviation of predictions using the unsteady-state WVP (R ² = 0.974). The same was observed only until day 15 for predictions obtained with the steady-state WVP. Calculations for days 20–25 overestimated the moisture uptake by 6.0–7.2%, resulting in registered R ² = 0.924. The unsteady-state WVP determination is low-cost, uses large numbers of film samples, and allowed more accurate predictions of dry mango moisture uptake. Knowledge of the moisture uptake controlled by the film WVP is essential when predicting the safety and quality changes limiting the shelf-life of foods.     

Synergistic Processing of Skim Milk with High Pressure Nitrous Oxide,Heat, Nisin,and Lysozyme to Inactivate Vegetative and Spore-Forming Bacteria

Individual and combined effects of high pressure nitrous oxide (HPN₂O), heat, and antimicrobials on the inactivation of Escherichia coli, Listeria innocua, and Bacillus atrophaeus endospores in milk were all evaluated after 20-min treatments. Stand-alone milk treatments with HPN₂O (15.2 MPa), heat (45 and 65 °C), or nisin (50 and 150 IU mL^?1) resulted in log₁₀ reductions ranging only from 0.1 to 2.1 for E. coli and L. innocua. Combining HPN₂O (15.2 MPa) with heat (65 °C) inactivated 6.0 and 5.1 log₁₀ in the vegetative bacteria, respectively. Similarly, reductions of 5.9 and ≥ 6.0 log₁₀ of respective E. coli and L. innocua cells in milk were achieved through a combination of HPN₂O (15.2 MPa), heat (65 °C), and nisin (150 IU mL^?1). A 2.5 log₁₀ cycle inactivation of spores was obtained by HPN₂O, nisin (at both 50 and 150 IU mL^?1), and lysozyme (50 μg mL^?1) at 85 °C. Combining these processing techniques resulted in significantly greater microbial inactivation (p < 0.05) than the sum of individual reductions from each treatment alone, indicating synergistic effects. HPN₂O irrespective of processing temperatures did not cause any occurrence of sub-lethally injured cells or disruption in colloidal stability of milk at 65 and 85 °C (p ≥ 0.05). Color and pH changes in milk following the most demanding treatment conditions were minimal.     

Comparative inactivation studies of <Emphasis Type="Italic">Aegle marmelos</Emphasis> (<Emphasis Type="Italic">bael</Emphasis>) peroxidase in crude extract of fruit by heat processing and ultrasonication treatment

Bael (Aegle marmelos) is considered as a holy fruit comprised of vast number of phytonutrients. Whole bael tree including all its parts has medicinal significance. Lack of awareness and seasonal nature makes its processing rather challenging. Conventional heat processing may lead to inactivation of quality hampering enzymes such as peroxidase, but at the cost of loss in essential phytonutrients. In the present work it was observed that thermal inactivation of bael peroxidase obeyed first order kinetics with enzyme activation energy of 7.7 kJ mol^?1. Complete inactivation of bael peroxidase was achieved within 11 min at 85?°C while ultrasound treatment attained in lesser time of 4 min at 64.07 W cm^?2 ultrasonic intensity. Loss of marmelosin a well-known phytonutrient in bael fruit was found to be 83.29?% by heat (11 min, 85?°C) and only 50.20?% by ultrasonication (4 min, 64.07 W cm^?2 ultrasonic intensity). Ultrasonication has potential to overcome harmful effects of heat processing with retention of phyto-constituents and hence has promising future in various food processing applications.     

Novel Intact Bitter Cassava: Sustainable Development and Desirability Optimisation of Packaging Films

Novel biomaterials and optimal processing conditions are fundamental in low-cost packaging material production. Recently, a novel biobased intact bitter cassava derivative was developed using an intrinsic, high-throughput downstream processing methodology (simultaneous release recovery cyanogenesis). Processing of intact bitter cassava can minimise waste and produce low-cost added value biopolymer packaging films. The objective of this study was to (i) develop and characterise intact bitter cassava biobased films and (ii) determine the optimal processing conditions, which define the most desirable film properties. Films were developed following a Box-Behnken design considering cassava (2, 3, 4 % w/v), glycerol (20, 30, 40 % w/w) and drying temperature (30, 40, 50 °C) and optimised using multi-response desirability. Processing conditions produced films with highly significant (p?<?0.05) differences. Developed models predicted impact of processing conditions on film properties. Desirable film properties for food packaging were produced using the optimised processing conditions, 2 % w/v cassava, 40.0 % w/w glycerol and 50 °C drying temperature. These processing conditions produced films with 0.3 %; transparency, 3.4 %; solubility, 21.8 %; water-vapour-permeability, 4.2 gmm/m²/day/kPa; glass transition, 56 °C; melting temperature, 212.6 °C; tensile strength, 16.3 MPa; elongation, 133.3 %; elastic modulus, 5.1 MPa and puncture resistance, 57.9 J, which are adequate for packaging applications. Therefore, intact bitter cassava is a viable material to produce packaging films that can be tailored for specific sustainable, low-cost applications.     

Characterization of Biodegradable Films Based on <Emphasis Type="Italic">Salvia hispanica</Emphasis> L. Protein and Mucilage

Biodegradable films of chia by-products (mucilage and protein-rich fraction (PF)) incorporated with clove essential oil (CEO) were obtained and characterized. The effects of polymer concentration (PC; 1.0–3.0 %, w/v) and CEO concentration (0.1–1.0 %, v/v) were evaluated as well as the pH (7–10), using a 2³ factorial design with four central points. The films exhibited moisture values between 11.6 and 52.1 % (d.b.), which decreased (p?<?0.05) with increasing PC and CEO. The thickness of the films increased (p?<?0.05) with increasing PC. PC and pH influenced (p?<?0.05) the lightness (L) and variation in color between red and green (a). The orientation of the color to yellow-blue hues (b) decreased significantly (p?<?0.05) with increasing PC. Transparency was significantly lower and higher (p?<?0.05) than PC and CEO, respectively. The film surface morphology was evaluated using atomic force miscrocope images, and thermogravimetric analysis (TGA) was performed to study the thermal stability of the films. The displacement and tensile strength were significantly lower (p?<?0.05) at higher concentrations of CEO, this variable being the only one with a significant effect. The chemical composition of the films was confirmed utilizing Fourier transform infrared (FTIR) spectroscopy. The proportion of CEO added to the films had a significant influence on antimicrobial activity, inhibiting the growth of both Escherichia coli and Staphylococcus aureus.     

Comparative Study on the Inactivation and Photoreactivation Response of <Emphasis Type="Italic">Listeria monocytogenes</Emphasis> Seafood Isolates and a <Emphasis Type="Italic">Listeria innocua</Emphasis> Surrogate after Pulsed Light Treatment

The inactivation and photoreactivation response of six seafood-isolated Listeria monocytogenes and one Listeria innocua strain after pulsed light (PL) treatment was evaluated. The lower inactivation levels found after exposure of treated samples to daylight during the first 90 min of storage confirmed that both L. innocua and L. monocytogenes have the capability to photorepair PL-induced DNA damage upon appropriate conditions. Photoreactivation levels from 0.2 to 2.1 log CFU cm^?2 were observed depending on treatment intensity (fluence) and Listeria strain. Complete photorepair of PL-caused damage was not found even after treatments inducing low inactivation levels. Photoreactivation increased up to 2.1 log with the applied fluence up to a threshold able to cause between 2.4 and 5.4 log reductions under dark storage. Photorepair was not avoided but lower photoreactivation was observed after higher fluence inducing more than 6 log reductions under dark storage. Both L. innocua and L. monocytogenes serotype 1/2b exhibited the highest photoreactivation levels whereas serotypes 1/2a showed the lowest ones. The overall inactivation and photoreactivation responses of tested Listeria strains were comparable indicating that L. innocua may be a good surrogate for the safe evaluation, optimization and validation of PL technology to control L. monocytogenes in food products and food processing facilities.     

Automated Sequential Injection Method for Determination of Caffeine in Coffee Drinks

An automated sequential injection analysis spectrophotometric assay for the determination of purine alkaloids in coffee drinks was developed. The sample was treated with a carrez reagent for matrix suppression followed by filtration; subsequently, alkaloids were separated from organic acids using a short C18 monolithic column (10 × 4.6 mm). The flow rate of the separation step was 10 μL s^?1 with 10% v/v of methanol as the mobile phase. The sum of alkaloids evaluated as caffeine was detected at 274 nm. The influence of the main parameters affecting the quantification of purine alkaloids was optimized. One sample analysis lasted 15 min when aspirated in triplicate. The linear range was 1–15 mg L^?1, and the determination coefficient (r ²) was 0.9969. The limit of detection and limit of quantitation were 0.128 and 0.425 mg L^?1, respectively. The repeatability evaluated as the relative standard deviation (RSD) was 3.58% (n = 12, 10 mg L^?1). Under optimal conditions, the method was successfully applied to determine purine alkaloids in different real samples including soluble coffee, coffee from an espresso machine, and brewed coffee drinks.     

Effect of Addition of Native Agave Fructans on Spray-Dried Chayote (<Emphasis Type="Italic">Sechium edule</Emphasis>) and Pineapple (<Emphasis Type="Italic">Ananas comosus</Emphasis>) Juices: Rheology,Microstructure, and Water Sorption

The effect of the combination of maltodextrin DE 10 (MD) and native agave fructans (FR) in concentrations of 0, 2, and 4% (w/v) on the rheological properties, microstructure, and water sorption of spray-dried chayote and pineapple powders was evaluated. A 10% (w/v) maltodextrin treatment was used as a control to compare treatments added with fructans. The scanning electron micrographs revealed spherical particles in a range from 16 to 105 μm with shrinkage, whereby greater caking and agglomeration occurred among particles in treatments with native agave fructans. The flow behavior of all juices can be described by the Bingham model with low plastic viscosities (0.0026 to 0.0030 Pa s^?1); the isotherms of the powders show a sigmoid shape pointing to the easy union of the fructans with water molecules. These types of isotherms are common for non-porous foods, and are indicative of physical adsorption in multi-layers where the adsorbate conserves its identity.     

Optimization of the QuEChERS Method for Determination of Pesticide Residues in Chicken Liver Samples by Gas Chromatography-Mass Spectrometry

The goal of this research was to evaluate the application of Quick, Easy, Cheap, Effective, Rugged, and Safe (QuEChERS) method for the determination of organochlorine, organophosphate, and carbamate pesticides in fatty animal matrices such as liver of chicken obtained from National Research Institute of Animal Production in Balice (Poland). Pesticides extraction effectiveness was evaluated at two different spiking levels (0.010 and 0.020 mg kg^?1) and efficiency of the dispersive solid-phase extraction (d-SPE) clean-up step was evaluated by comparison adding different d-SPE sorbent combinations (PSA?+?GCB, PSA?+?C₁₈, PSA?+?SAX, and PSA?+?NH₂). The analysis of pesticide residues was performed by gas chromatography ion trap mass spectrometry (GC/IT-MS). The linear relation was observed from 0 to 400 ng mL^?1 and the determination coefficient R ²?>?0.997 in all instances for all target analytes. Better recoveries were obtained in samples at 0.020 mg kg^?1 spiking level. The recoveries were in the range 70–120 %, with relative standard deviation (RSD) values lower than 15 % at 0.020 mg kg^?1 spiking level for most pesticides. Similar recovery ratios were obtained with the four different combinations of sorbents tested in the clean-up step, with better precision when the (PSA?+?SAX) combination was tested. Limits of detection (LODs) ranged from 0.001 to 0.005 mg kg^?1 and limits of quantification (LOQs) ranged from 0.003 to 0.015 mg kg^?1. The proposed method was successfully applied analyzing pesticide residues in real chicken liver samples; detectable pesticide residues were observed, but in all of the cases, the contamination level was lower than the default maximum residue levels (MRLs) set by European Union (EU), Regulation (EC) N 396/2005.     

Effect of Solids Concentration on the Physicochemical and Flow Properties of Cactus Pear Juices of Two Varieties (<Emphasis Type="Italic">Opuntia ficus-indica</Emphasis> and <Emphasis Type="Italic">Opuntia streptacantha</Emphasis>)

Juices from two varieties of cactus pear, a green (Opuntia ficus-indica) and a red (Opuntia streptacantha), were obtained and concentrated by evaporation. Both fruit varieties and their juices at different concentrations were characterized. Green cactus pears had significantly higher amount of pulp than red cactus pears; the peel of O. ficus-indica represented only 38 versus 52 % of the fruit for the O. streptacantha. Both varieties had no significant differences on moisture, density, pH, and titratable acidity, in contrary to soluble solids. Juice was concentrated under vacuum conditions to reach a final concentration of 42, 53–55, and 58–60 °Brix, respectively, and stored under refrigeration (10 °C) during 4 weeks. Physicochemical properties of the pears and juices were determined as fresh items (time zero) and every week for the concentrate juices through storage; similarly, flow parameters were measured at 10 and 25 °C. Concentrate density (1160–1283 kg/m³) was mainly affected by final soluble solids, while pH and acidity were affected differently depending on the variety. Concentrated juices at 42 °Brix were considered with Newtonian behavior with a viscosity of 2–22 mPa s, while those at higher concentrations were of pseudoplastic nature (n < 1.0 and K > 69 mPa sⁿ). Power Law model fitted better the flow behavior than Herschel-Bulkley model of concentrates of both varieties. Temperature, solid concentration, and/or storage time affected the consistency coefficient (K) and flow index (n) depending on the cactus pear variety. Overall, those concentrated juices from O. streptacantha were more stable and exhibited lower apparent viscosity.     

An approach for extraction,purification, characterization and quantitation of acylated-anthocyanins from <Emphasis Type="Italic">Nitraria tangutorun</Emphasis> Bobr. fruit

In the present study, a systematic approach for extraction, purification and analysis of acylated-anthocyanins from Nitraria tangutorun Bobr. fruit was explored. Six acylated-anthocyanins in N. tangutorun fruit were identified by HPLC-MS/MS, and a rapid and efficient HPLC-DAD method was developed to analyze the acylated-anthocyanins. Ultrasonic-assisted extraction conditions of acylated-anthocyanins were optimized using response surface methodology, extraction at 70 °C for 32 min using 70% methanol solution (0.1% HCl, v/v) rendered an extract with 80.37?±?2.66 mg/100 g of cyanidin-3-O-(trans-p-coumaroyl)-diglucoside and 97.88?±?4.06 mg/100 g of total acylated-anthocyanins. Nine macroporous resins were investigated for preliminary purification of acylated-anthocyanins. According to the static/dynamic adsorption and desorption tests, XDA-6 macroporous resin exhibited the maximum potential for preparing acylated-anthocyanins. The purity of cyanidin-3-O-(trans-p-coumaroyl)-diglucoside (43.30 mg/g) in purified acylated-anthocyanins was 201.89 times of that of the extract (0.21 mg/g), and the purity of total acylated-anthocyanins increased from 0.36 to 56.44 mg/g. Besides, the stability (t _1/2) of cyanidin-3-O-(trans-p-coumaroyl)-diglucoside and total acylated-anthocyanins increased by more than five-fold after purification using XDA-6. The established methods of analysis, extraction and purification of acylated-anthocyanins were hopefully utilized in food industry.