核壳结构纳米TiO2／PMMA／PU复合基耐洗刷涂料制备

为制备水性聚氨酯（WPU）耐洗刷涂料,用硅烷偶联剂改性纳米TiO2,并采用预聚体分散、种子原位乳液聚合法分别制备了TiO2／PU、TiO2／聚甲基丙烯酸甲酯（PMMA）／PU复合乳液。探讨了n（-NCO）：n（-OH）（R值）、纳米TiO2加入方式与含量、MMA／PU质量比及填料与功能助剂类型对PU耐洗刷性能的影响。透射电镜形貌观察表明：TiO2／PMMA／PU复合乳液乳胶粒子具有以TiO2为核的核壳结构。结果表明乳液种类对涂膜耐洗刷性影响较大,当纳米TiO2含量为0．5％、PMMA／PU质量比1：4时,多层核壳结构复合乳液的耐洗刷性最好,达6350次;选择片状结构、质地较硬的填料、微纤及防水助剂能显著提高PU涂料耐洗刷性,优化配方可制备出耐洗刷性达10000次以上PU乳液涂料。     

核壳结构纳米TiO_2/PU/PMMA复合材料制备及其光催化性能研究

采用纳米TiO2有机化改性、加成及原位乳液聚合,制备了纳米TiO2、聚氨酯(PU)、聚丙烯酸酯(PMMA)的复合材料。透射电镜形貌表明:合成了以纳米TiO2为核,PU与PMMA为壳的核壳结构的复合材料。研究了该复合材料的光催化性能。     

纳米TiO2/PSB复合乳液的制备与性能研究

为了提高丁苯乳液涂膜力学性能,用硅烷偶联剂(KH-570)改性纳米TiO2,采用半连续种子乳液聚合法,制备TiO2/聚丁苯(PSB)复合乳液。采用FT-IR、TEM表征TiO2/PSB复合乳液乳胶粒子结构,结果表明合成了以TiO2为核的核壳结构纳米TiO2/PSB乳胶粒子。探讨了纳米TiO2、乳化剂、电解质、引发剂及增稠剂用量、聚合时间与温度、单体配比等对TiO2/PSB复合乳液性能的影响。确立了适宜的聚合工艺条件:纳米TiO2、乳化剂用量分别为总质量的0.5%和3.5%,电解质和引发剂用量为单体质量的0.4%,聚合温度和时间分别为64℃和3.5 h,可制备出高固高黏且性能优良的复合乳液。经纳米TiO2改性的PSB复合乳液涂膜性能较未改性的,在黏度、硬度、耐冲击性、耐洗刷性、附着力及耐水性等方面均有明显改善。     

细乳液聚合法TiO_2/PMMA纳米复合粒子的制备及其性能

采用细乳液聚合法制备了二氧化钛/聚甲基丙烯酸甲酯(TiO2/PMMA)纳米复合粒子,研究了引发剂、助乳化剂、乳化剂、单体结构对TiO2/PMMA纳米复合粒子性能的影响。结果表明,十六烷(HD)比十二醇和十六醇更能有效抑制甲基丙烯酸甲酯(MMA)液滴在水相中的Ostwald熟化效应,当MMA占TiO2质量的60%,HD占单体质量的6%,可聚合乳化剂1-烯丙氧基-3-(4-壬基苯酚)-2-丙醇聚氧乙烯(10)醚硫酸铵(DNS-86)占整个体系质量的2%时,制备TiO2/PMMA纳米复合粒子分散体的粒径为185 nm,此时TiO2/PMMA纳米复合粒子与细乳液粒径差距较小;采用TiO2/PMMA纳米复合粒子制备喷墨印花用白色涂料墨水的稳定性和遮盖力明显优于同等条件下TiO2所制备的涂料墨水。     

基于细乳液聚合法TiO2/PMMA纳米复合粒子的制备及其性能

采用细乳液聚合法制备了二氧化钛/聚甲基丙烯酸甲酯（TiO2/PMMA）纳米复合粒子,考察了引发剂、助乳化剂、乳化剂、单体结构和种类对TiO2/PMMA纳米复合粒子性能的影响。结果表明与十二醇和十六醇相比,十六烷（HD）更能抑制甲基丙烯酸甲酯（MMA）液滴的Ostwald熟化效应,当MMA占TiO2质量分数的60%,HD对单体质量分数的6%,可聚合乳化剂1-烯丙氧基-3-(4-壬基苯酚)-2-丙醇聚氧乙烯(10)醚硫酸铵（DNS-86）占整个体系的质量分数为2%时,制备TiO2/PMMA纳米复合粒子分散体的粒径为185nm,此时TiO2/PMMA纳米复合粒子与细乳液粒径差距较小;采用TiO2/PMMA纳米复合粒子制备白色涂料墨水的稳定性和遮盖力明显优于同等条件下TiO2所制备的涂料墨水。     

核壳结构纳米TiO_2/丁苯复合乳液制备研究

以硅烷偶联剂改性的纳米TiO2为核,阴离子乳化剂十二烷基硫酸钠(SDS)与非离子乳化剂壬基酚聚氧乙烯醚(OP-10)为复合乳化剂,其质量比为1:1,采用半连续种子乳液聚合法,制备了具有核壳结构的纳米TiO2/聚丁苯(PSB)复合乳液,其固含量最高可达50%以上,黏度可依据不同使用要求进行调节。     

核壳结构纳米TiO_2/丁苯复合乳液制备研究

为制备高固高粘新型丁苯乳液(SBRL),以经硅烷偶联剂改性的纳米TiO2为核,阴离子乳化剂十二烷基硫酸钠(SDS)与非离子乳化剂辛基苯基聚氧乙烯醚(OP-10)为复合乳化剂,其质量比为1:1,采用半连续种子乳液聚合法,制备了具有核壳结构的纳米TiO2/聚丁苯(PSB)复合乳液,并测定了复合乳液的性能。确定了适宜聚合工艺条件:纳米TiO2为总量0.5%,乳化剂用量为3.5%,引发剂用量为单体量0.4%,聚合温度为64℃,可以制备出性能良好的复合乳液。所制乳液固含量最高可达50%以上,粘度可依据不同使用要求调节。     

核壳型纳米SiO2-聚丙烯酸酯复合乳液的制备及应用

本文根据核壳乳液聚合理论,以硅烷偶联剂表面处理的纳米S iO2为种子,采用优化的乳液聚合工艺,制备核壳型纳米S iO2-聚丙烯酸酯复合乳液,并以其为基料制备建筑涂料。实验结果表明,纳米S iO2经硅烷偶联剂表面处理后,提高了其在聚合体系中的分散稳定性和与聚合物的相容性。所制备的复合乳液粒子具有核壳结构,以其为基料制备的建筑涂料的耐沾污性、耐洗刷性和耐候性等性能大大高于国家标准中优等品的水平。     

PMMA/PAN核-壳粒子制备工艺研究

加入适量的引发剂,通过无皂乳液聚合,以聚甲基丙烯酸甲酯( PMMA)核体为种子乳液,制备了PMMA/PAN核-壳乳液.实验中分别对引发剂量、丙稀腈( AN)滴加量对PMMA/PAN壳层厚度及其粒径和粒径分布的影响进行了较详细的研究,确定了种子乳液聚合法制备PMMA/PAN核-壳结构聚合物粒子的实验方法及条件.通过激光粒度仪、扫描电镜和透射电镜对核-壳粒子的形态结构进行了表征,证明了PMMA/PAN复合粒子的核-壳结构.     

纳米TiO2/甲基丙烯酸甲酯原位乳液聚合研究

采用原位乳液聚合方法制备聚甲基丙烯酸甲酯(PMMA)包覆TiO2(TiO2／PMMA)，发现纳米TiO2对甲基丙烯酸甲酯的聚合无阻聚作用。研究表明：PMMA包覆在纳米TiO2表面主要为物理包覆，有少量化学包覆。在丙烯酸涂料中，TiO2／PMMA比TiO2更易分散。用TiO2／PMMA制得的涂料流平性好，涂膜性能优良。     

Preparation and properties of poly(Nε,Nε-dicarboxymethyl-l-lysine)

A new ampholytic homopolypeptide, $\text{poly}\text{(N}{}^{\mathrm{\epsilon }}\text{,N}{}^{\mathrm{\epsilon }}\text{-}\text{dicarboxy-methyl-}\text{l}\text{-lysine}\text{)}$, which has one tertiary amino and two carboxyl groups in the side chain has been derived from a hydrochloride salt of poly(L-lysine). The polymer in aqueous solution seems to be in the coil form with locally extended structure (LES) at neutral pH. In both the acidic and alkaline regions, the molar ellipticity of the polymer changes as a result of change in net charge on the side chain. The conformational changes may be from the coil with LES to other coiled forms. 5–7 M NaClO₄ and 80% aqueous methanol induce the α-helix in the polymer at neutral pH. Divalent cations, Cu²⁺ and Ca²⁺, do not induce any remarkably ordered structures such as α-helix or β-structure in the polymer in aqueous solution at any pH. Ultraviolet absorption studies show an absorption peak of the polymer-Cu²⁺ complex near 240 nm. Dependence of the peak intensity on pH at various q values ($\text{q =}\text{[}\text{Cu}{}^{\mathrm{2+}}\text{]}\text{[}\text{residue}\text{]}$) indicates the two steps of the complex formation. At q less than 0.64, the formation is described only with the first step. An average coordination number for Cu²⁺ at the first step was calculated to be about 2 by the method of Mandel and Leyte. The association constant of Cu²⁺ with the residue at the step was determined from the absorption data to be far smaller than that for the Cu²⁺-EDTA complex. The second step of the formation occurs in the case of large q but the absorption data for the second step cannot be obtained exactly due to precipitation.     

Wet Milling of Fe/Al/Al2O3 and Fe2O3/Al/Al2O3 Powder Mixtures

Wet milling of Al₂O₃-aluminide alloy (3A) precursor powders in acetone has been investigated by milling Fe/Al/Al₂O₃ and Fe₂O₃/Al/Al₂O₃ powder mixtures. The influence of the milling process on the physical and chemical properties of the milled powders has been studied. Particle refinement and homogenization were found not to play a dominant role, whereas plastic deformation of the metal particles leads to the formation of dislocations and a highly disarranged polycrystalline structure. Although no chemical reactions among the powder components in Fe₂O₃/Al/Al₂O₃ powder mixtures were observed, the formation of a nanocrystalline, ordered intermetallic FeAl phase in Fe/Al/Al₂O₃ powder mixtures caused by mechanical alloying was detected. Chemical reactions of Fe and Al particle surfaces with the atmosphere and the milling media lead to the formation of highly porous hydroxides on the particle surfaces. Hence the specific surface area of the powders increases, while the powder density decreases during milling. The fraction of Fe oxidized during milling was determined to be 0.13. The fraction of Al oxidized during milling strongly depends on the metal content of the powder mixture. It ranges between 0.4 and 0.8.     

Participation of lewis base on vinyl chloride polymerization with Al(C2H5)3CCl4 catalyst system

The polymerization of vinyl chloride has been investigated using an $\text{Al}\text{(}\text{C}{}_2\text{H}{}_5\text{)}{}_3\text{CCl}{}_4$ catalyst system in the presence of various Lewis bases. Effective Lewis bases are γ-butyrolactone, diglyme and diethylenetriamine which are multidentate. The rate of polymerization is dependent not only on the basicity of the Lewis base used but also on a coordination number of one. The latter is the predominant factor. For the effect of polymeric amines, a tentative hypothesis is discussed.     

Sintering of Si3N4-Y2O3-Al2O3

Sintering kinetics of the system Si₃N4-Y2O₃-Al₂O3 were determined from measurements of the linear shrinkage of pressed disks sintered isothermally at 1500° to 1700°C. Amorphous and crystalline Si₃N₄ were studied with additions of 4 to 17 wt% Y₂O₃ and 4 wt% A1₂O₃. Sintering occurs by a liquid-phase mechanism in which the kinetics exhibit the three stages predicted by Kingery's model. However, the rates during the second stage of the process are higher for all compositions than predicted by the model. X-ray data show the presence of several transient phases which, with sufficient heating, disappear leaving mixtures of β ' -Si₃N₄ and glass or β '-Si₃N₄, α '-Si₃N₄, and glass. The compositions and amounts of the residual glassy phases are estimated.     

Synthesis and Characterization of Ti0.33Ta0.33Nb0.33C and Ti0.33Ta0.33Nb0.33CxN1-x Whiskers

Ta_0.33Ti_0.33Nb_0.33C and Ta_0.33Ti_0.33Nb_0.33C _x N_{1− x} whiskers were synthesized via a carbothermal vapor-liquid-solid growth mechanism in the temperature range 900°-1450°C in Ar or N₂. The optimum temperature was 1250°C. Whiskers were obtained in a yield of 70-90 vol%. The whiskers were 0.5–1 µm in diameter and 10–30 µm in length. The starting materials that produced the highest whisker yield were: TiO₂, Ta₂O₅, Nb₂O₅, C, Ni, and NaCl. C was added to reduce the oxides, and Ni to catalyze whisker growth. NaCl was used as a source of Cl for vapor-phase transportation of Ta and Nb oxochlorides and Ti chlorides to the catalyst. The catalyst metal was recycled several times during the synthesis and was transported as NiCl₂( g ) according to thermodynamic calculations. The rate of formation and the chemical composition of the whiskers depended on the synthesis temperature, the choice of catalyst, and the atmosphere. At low temperatures, the whiskers were enriched in Nb and Ta, whereas the Ti content increased with increased synthesis temperature.