An investigation on the spray characteristics of DME with variation of ambient pressure using the common rail fuel injection system

We investigated the DME spray characteristics about varied ambient pressure and fuel injection pressure using the common rail fuel injection system when the nozzle holes diameter is varied. The common rail fuel injection system and fuel cooling system were used since DME has compressibility and vaporization at atmospheric temperature. The fuel injection quantity and spray characteristics were measured. The spray was analyzed for spray shape, penetration length, and spray angle at the six nozzle holes. There are two types of injectors: 0.166 mm diameter and 0.250 mm diameter. The ambient pressure, which was based on gage pressure, was 0, 2.5, and 5 MPa. The fuel injection pressure was varied by 5 MPa from 35 to 70 MPa. By comparing with the common injector, using the converted injector it was shown that the DME injection quantity was increased 127% but it didn??t have the same low heating value. Both the common and converted injectors had symmetric spray shapes. In case of converted injector, there were asymmetrical spray shapes until 1.2 ms, but after 1.2 ms the spray shapes were symmetric. Also, the converted injector had shorter penetration length and wider spray angle than the common injector.     

The effects of injector nozzle geometry and operating pressure conditions on the transient fuel spray behavior

Effects of injector nozzle geometry and operating pressure conditions such as opening pressure, ambient pressure, and injection pressure on the transient fuel spray behavior have been examined by experiments. In order to clarify the effect of internal flow inside nozzle on the external spray, flow details inside model nozzle and real nozzle were also investigated both experimentally and numerically. For the effect of injection pressures, droplet sizes and velocities were obtained at maximum line pressure of 21 MPa and 105 MPa. Droplet sizes produced from the round inlet nozzle were larger than those from the sharp inlet nozzle and the spray angle of the round inlet nozzle was narrower than that from the sharp inlet nozzle. With the increase of opening pressure, spray tip penetration and spray angle were increased at both lower ambient pressure and higher ambient pressure. The velocity and size profiles maintained similarity despite of the substantial change in injection pressure, however, the increased injection pressure produced a higher percentage of droplet that are likely to breakup.     

Spray characteristics of the rotating fuel injection system of a micro-jet engine

In micro-turbojet engines with less than 350 kW power, it is not easy to find a suitable fuel injector with good spray quality. However, the rotating fuel injection system can potentially provide high atomization quality without the high-pressure fuel pump through the centrifugal forces of the engine shaft. With this motivation, a very small rotating fuel injector with 40 mm diameter is designed for the micro-turbo jet engine. It is directly linked to a high-speed rotational spindle capable of a speed up to 100,000 rpm. The droplet size, velocity, and spray distribution from the PDPA (Phase Doppler Particle Analyzer) system are measured. The spray is also visualized by a high-speed camera. The test results show that the length of liquid column from injection orifice is controlled by the rotational speeds and that SMD (Sauter Mean Diameter) is decreased with increasing rotational speeds. At a rotational speed of 73.3 m/s (35,000 rpm), SMD is lower than 60 μm at the entirety of the measuring space in the case of Type 2 (injection orifice diameter of 1.5 mm) and Type 3 (injection orifice diameter of 2.2 mm). Therefore, conceptually, it is possible to apply this small rotating fuel injection system to the micro-turbojet engine combustor.     

A study on the spray characteristics of a piezo pintle-type injector for DI gasoline engines

We studied the spray flow initiated from a piezo pintle-type injector for DI gasoline engines in an environment supplied by a constant volume vessel by means of laser diagnostics. To fully grasp the effects of the characteristic parameters, including designed spray angle, needle lift, injection pressure (P _inj ) and ambient pressure (P _b ), on the spray atomization and mixture preparation, particle image velocimetry (PIV) and phase Doppler anemometry (PDA) are used in the experiment, respectively. The gas perpendicularly enters into the outer periphery of the conical spray injected through the pintle-type injector activated by piezo, which creates two large-scale vortices: the vortex A and vortex B. The velocity standard deviation of the spray field is introduced to analyze the gas flow motion in the vicinity of nozzle. The droplet information of spray field is also recorded by PDA in variable boundary conditions. The time dividing method is used to study the droplet characteristics in four parts of spray. The injector with 98° designed spray angle has smaller droplet mean diameter (D10 and D32), due to a larger spray distribution. When the droplet velocity of the spray field is close to 0 m/s, the D10 and D32 hold at around 10 μm and 20 μm, respectively, in atmospheric pressure condition, which are about 20 μm and 40 μm, respectively, at ambient pressure of 1.1 MPa.     

The effect of injection pressure and fuel viscosity on the spray characteristics of biodiesel blends injected into an atmospheric chamber

An experimental study was conducted to examine the effect of injection pressure and fuel type on the spray tip penetration length and the angle of spray injected into atmospheric chamber. The objective of the present study is to formulate empirical correlations of the spray tip penetration and the spray angle for non-evaporative condition. The experiment was performed by a common rail type high-pressure injector for the diesel engine at the injection pressure 40??100 MPa and four different fuels (D100, BD25, BD45, and BD65). The results showed that the biodiesel content increased the spray tip penetration and decreased the spray angle. The correlation of spray tip penetration is expressed for each region before and after spray break-up time in terms of injection pressure, fuel viscosity and time after start of injection. The correlation is also obtained for spray angle equation terms of injection pressure and fuel viscosity.     

Effects of different piezo-acting mechanism on two-stage fuel injection and CI combustion in a CRDi engine

In this study, the effects of two piezo injectors operated by different mechanisms on multi-injection and Compression ignition (CI) combustion were investigated. High-pressure injectors for CI engines are divided into two categories according to the actuator: Solenoid and piezo injectors. It is commonly known that both injectors have a hydraulic circuit for fuel injection; thus, the performance of the injector is highly dependent on not only hydraulic characteristics such as volume of internal chambers and nozzle geometry, but also the actuation mechanism. Specially, the direct needle-Driven piezo injector (DPI) is introduced in this study and compared with the indirectacting Piezo injector (PI) to investigate the injection characteristics and influences on CI combustion performance by using spray visualization, injection rate measurement, and single cylinder diesel engine experiments, as well as numerical simulation for injection rate modeling of DPI. In the spray visualization experiment, a high-speed camera was used to examine spray tip penetration length and spray speed with respect to each injector. Also, in order to investigate injection rate information, which is a significantly dominant factor in combustion characteristics, the Bosch-tube method was adapted under the condition of a back pressure of 4.5 MPa, corresponding to engine motoring pressure. Also, a single-cylinder CRDi (Common-rail direct-injection) engine experiment was carried out to determine the effects of different piezo-acting mechanisms on two-stage fuel injection and CI combustion. From the key results obtained by this study, the direct needle-driven piezo injector has a faster SOI (Start of injection) and EOI (End of injection). In addition, the overall shape of the injection rate of DPI was narrow and the injection had a higher spray speed than that of PI. Also, DPI has a higher heat release rate and peak pressure, as verified by the engine experiment. In particular, it was found that DPI showed the possibility of combustion improvement when applying a pilot injection strategy.

     

两相脉冲爆震发动机头部燃油雾化试验研究

在不同油、气流量下,采用LS-2000激光喷雾粒度分析仪测试了脉冲爆震发动机头部为空心腔体结构、文丘里结构情况下的油滴索太尔平均直径(SMD),并与实验中所采用的直射式喷油嘴雾化结果进行了比较,简要分析了头部几何结构对喷入燃油的二次雾化过程。研究发现,除了喷嘴性能以外,发动机头部几何结构对油滴粒度也具有较为显著的影响,而且设计中应使所采用的喷嘴型式与其相匹配。     

Atomization characteristics and prediction accuracy of LISA-DDB model for gasoline direct injection spray

In this paper, the spray atomization characteristics of a gasoline direct-injection injector were investigated experimentally and numerically. To visualize the developing spray process, a laser sheet method with a Nd :YAG laser was utilized. The microscopic atomization characteristics such as the droplet size and velocity distribution were also obtained by using a phase Doppler particle analyzer system at the 5 MPa of injection pressure. With the experiments, the calculations of spray atomization were conducted by using the KIVA code with the LISA-DDB breakup model. Based on the agreement with the experimental results, the prediction accuracy of LISA-DDB breakup model was investigated in terms of the spray shapes, spray tip penetration, SMD distribution, and axial mean velocity. The results of this study provides the macroscopic and microscopic characteristics of the spray atomization, and prediction accuracy of the LISA-DDB model.     

Elimination of Fuel Pressure Fluctuation and Multi-injection Fuel Mass Deviation of High Pressure Common-rail Fuel Injection System

The influence of fuel pressure fluctuation on multi-injection fuel mass deviation has been studied a lot,but the fuel pressure fluctuation at injector inlet is still not eliminated efficiently.In this paper,a new type of hydraulic filter consisting of a damping hole and a chamber is developed for elimination of fuel pressure fluctuation and multi-injection fuel mass deviation.Linear model of the improved high pressure common-rail system(HPCRS)including injector,the pipe connecting common-rail with injector and the hydraulic filter is built.Fuel pressure fluctuation at injector inlet,on which frequency domain analysis is conducted through fast Fourier transformation,is acquired at different target pressure and different damping hole diameter experimentally.The linear model is validated and can predict the natural frequencies of the system.Influence of damping hole diameter on fuel pressure fluctuation is analyzed qualitatively based on the linear model,and it can be inferred that an optimal diameter of the damping hole for elimination of fuel pressure fluctuation exists.Fuel pressure fluctuation and fuel mass deviation under different damping hole diameters are measured experimentally,and it is testified that the amplitude of both fuel pressure fluctuation and fuel mass deviation decreases first and then increases with the increasing of damping hole diameter.The amplitude of main injection fuel mass deviation can be reduced by 73%at most under pilot-main injection mode,and the amplitude of post injection fuel mass deviation can be reduced by 92%at most under main-post injection mode.Fuel mass of a single injection increases with the increasing of the damping hole diameter.The hydraulic filter proposed by this research can be potentially used to eliminate fuel pressure fluctuation at injector inlet and improve the stability of HPCRS fuel injection.     

An experimental study on spray and combustion characteristics based on fuel temperature of direct injection bio-ethanol-gasoline blending fuel

This study investigated the spray and combustion characteristics of a direct injection spark ignition type system based on the changes in the temperature of the blended fuel (with bio-ethanol and gasoline). The test was performed in a chamber with a constant volume. The diameter and width of the chamber were 86 mm and 39 mm, respectively. The bio-ethanol test fuel was blended at volume ratios of 0 %, 10 %, 20 % and 100 %. The temperature of the fuel was set as −7, 25 and 35 °C. The fuel injection pressure and ambient pressure were set as 4.5 and 0.5 MPa, respectively. The shape and characteristics of the spray were investigated through a spray experiment. The increase in the fuel temperature changed its density and viscosity; this in turn increased spray penetration and spray area and increased the bio-ethanol blending ratio. The combustion visualization and experimental analysis indicated that the decrease in the fuel temperature and the increase in the bio-ethanol blending ratio led to the high viscosity and low heating value. This resulted in an increase in the ignition delay and a decrease in the rate of heat release. It is necessary to adjust the spray strategy and ignition timing to adopt bio-ethanol blended fuel as an alternative fuel.

     

An experimental study on the spray characteristics of a dual-orifice type swirl injector at low fuel temperatures

The objective of this study is to investigate the effects of fuel temperature on the spray characteristics of a dual-orifice type swirl injector used in a gas turbine. The major parameters affecting spray characteristics are fuel temperature and injection pressure entering into the injector. In this study, the spray characteristics of a dual-orifice type swirl injector are investigated by varying fuel temperature from — 30°C to 120°C and injection pressure from 0.29 to 0.69 MPa. Two kinds of fuel having different surface tension and viscosity are chosen as atomizing fluids. As a result, injection instability occurs in the low fuel temperature range due to icing phenomenon and fuel property change with a decrease of fuel temperature. As the injection pressure increases, the range of kinematic viscosity for stable atomization becomes wider. The properties controlling the SMD of spray is substantially different according to the fuel temperature range.     

Numerical and experimental study on hollow-cone fuel spray of highpressure swirl injector under high ambient pressure condition

A hybrid breakup model was proposed as a trustworthy prediction of hollow-cone fuel spray in the present study and the atomization process of the hollow-cone fuel spray of a high-pressure swirl injector in a Gasoline Direct Injection (GDI) engine under high ambient pressure conditions was studied by a new hybrid breakup model. The proposed hybrid breakup model is composed of the Linearized Instability Sheet Atomization (LISA) model as a primary breakup process. The Aerodynamically Progressed Taylor Analogy Breakup (APTAB) model, instead of the Taylor Analogy Breakup (TAB) model, was used as a secondary breakup process. The effects of the droplet deformation on a droplet aerodynamic external force are considered in the APTAB model. In addition, we replaced the x ² distribution function used in previous the APTAB model by the Rosin-Rammler distribution function to improve the prediction precision. The Laser Induced Exciplex Fluorescence (LIEF) technique and the Phase Doppler Anemometry (PDA) system were used to produce a set of experimental data for the model validation. The estimation of the prediction ability of the LISA+APTAB model was carried out, and spray characteristics, which are difficult to obtain by experimental method, were calculated and discussed. The suggested hybrid breakup model showed better prediction capability compared with the previous model (LISA+TAB model). From the calculated results, the effect of the ambient pressure on the SMD (Sauter Mean Diameter) and droplet velocity could be discussed quantitatively.     

阀芯结构对双流体喷雾粒子特性的影响

为了研究阀芯结构对双流体喷雾粒子特性的影响,提升喷雾效果,运用相位多普勒粒子分析仪（PDPA）对不同阀芯结构的双流体喷雾雾滴粒径、轴向速度以及雾滴数目进行了测试,并对测量结果进行了分析和讨论。结果表明：随着轴向距离的增大,雾滴索特平均直径(SMD)、算术平均直径(AMD)呈先增大后趋于平缓的趋势,轴向速度以及湍流脉动速度均呈减小趋势,雾滴数目呈先增大后减小的趋势;随着气液压力比的增大,SMD呈先增大后减小的趋势,而AMD、轴向速度以及雾滴数目均呈减小趋势;阀芯的喉口直径、出口直径的减小均有利于喷雾效果的提升,但同时导致速度稳定性变差;当喉口直径为1.5mm、出口直径为2.5mm时,与原始阀芯结构相比,雾滴数目和雾滴轴向速度分别增大了82.43%和22.31%,SMD和AMD分别减小了52.18%和21.47%,综合喷雾效果得到了大幅提升。     

On the intermittent spray characteristics

The quality of spray atomization ejected from an injector has a definitive influence upon the engine’s performance. Furthermore, considerable attention to the Earth’s environmental pollution is increasing now more than ever before. This experimental investigation has been carried out to clarify the characteristics of the intermittent spray using a pintle type gasoline fuel injector. Both the image processing system and the Phase Doppler Anemometer are utilized for the visualization of a spray behavior and the simultaneous measurements of dropsizes and their velocities, which have been conducted at the axial downstream from the injector exit plane. The fuel injection duration was fixed at 3ms and the injection pressure was varied from 250 kPa to 350 kPa. For a high injection pressure of 350 kPa, the spray tip arrival time was fluctuated at the vigorously disintegrated regions. It evidently shows a linear correlation between the axial velocity and the fuel drop size farther downstream.     

Experimental analysis and numerical modeling using lisa-ddb hybrid breakup model of direct injected gasoline spray

This paper presents the effect of injection pressure on the atomization characteristics of high-pressure injector in a direct injection gasoline engine both experimentally and numerically. The atomization characteristics such as mean droplet size, mean velocity, and velocity distribution were measured by phase Doppler particle analyzer. The spray development, spray penetration, and global spray structure were visualized using a laser sheet method. In order to investigate the atomization process in more detail, the calculations with the LISA-DDB hybrid model were performed. The results provide the effect of injection pressure on the macroscopic and microscopic behaviors such as spray development, spray penetration, mean droplet size, and mean velocity distribution. It is revealed that the accuracy of prediction is promoted by using the LISA-DDB hybrid breakup model, comparing to the original LISA model or TAB model alone. And the characteristics of the primary and secondary breakups have been investigated by numerical approach.     

A study on fuel spray of spark-ignited direct injection engine using laser image technology

One of the important research for developing a spark-ignited direct injection engine is optimization of the fuel spray distribution and air flow field in the cylinder. Therefore, spray pattern and mean fuel droplet size of swirl injector were investigated using Laser Light Sheet Photography and PDPA' respectively. And, for the formation of stratified mixture with adequate strength near a spark plug at injection mode in compression stroke, spray distribution after impingement on flat piston or bowl piston in a transparent motoring engine was visualized for the three different injector positions. KIA Motors Corp.     

A study on the characteristics of soot formation and oxidation in free fuel droplet array

In this study, it was attempted to obtain the fundamental data for the formation and oxidation of soot from a diesel engine. Combustion of spray injected into a cylinder is complex phenomenon having physical and chemical processes, and these processes affect each other. There are many factors in the mechanism of the formation and oxidization of soot and it is necessary to observe spray combustion microscopically. In order to observe with that view, free fuel droplet array was used as an experimental object and the droplet array was injected into an atmospheric combustion chamber with high temperature. Ambient temperature of the combustion chamber, interdroplet spacing, and droplet diameter were selected as parameters, which affect the formation and oxidation of soot. In this study, it was found that the parameters also affect ignition delay of droplet. The ambient temperature especially affected the ignition delay of droplet as well as the flame temperature after self-ignition. As the interdroplet spacing that means the local equivalence ratio in a combustion chamber was narrow, formation of soot was increased. As diameter of droplet was large, surface area of the droplet was also broad, and hence evaporation of the droplet was more active than that of a droplet with relative small diameter.     

An experimental study on turbulent characteristics of an impinging split-triplet injector

This paper presents turbulent characteristics of an impinging F-O-O-F type injector in which fuel and oxidizer impinge on each other to atomize under the different momentum ratio. Water was used as an inert simulant liquid instead of fuel and oxidizer. The droplet size and velocity in the impinging spray flow field were measured using a PDPA. The gradient of the spray half-width(b₂) along the long-axis direction declined throughout the entire spray flow field with increasing the momentum ratio from 1.19 to 6.48. However, the gradient of the half-width(b₁) along the short-axis direction decreased with increasing the momentum ratio. The turbulence intensity and turbulent kinetic energy were converged into the center of the initial region with increasing the momentum ratio. As the momentum ratio increased from MR=1.19 to MR=6. 48, the turbulent shear stress decreased. The results of this study can be used for the design of an impinging type injector for liquid rockets.     

喷射压力对生物柴油混合燃料喷雾特性的影响

基于KH-RT液滴破碎模型对定容燃烧弹内生物柴油-正丁醇混合燃料的喷雾贯穿距离、喷雾锥角、索特平均粒径、速度场以浓度场进行数值模拟,通过定容燃烧弹试验台架获取的生物柴油-正丁醇混合燃料的喷雾特性对数值模型进行验证,结果表明:随着喷射压力的增加,BD70N30混合燃料的喷雾贯穿距和喷雾锥角增加;索特平均粒径降低;雾束中心...     

Effects of needle response on spray characteristics in high pressure injector driven by piezo actuator for common-rail injection system

The common-rail injection systems, as a new diesel injection system for passenger car, have more degrees of freedom in controlling both the injection timing and injection rate with the high pressure. In this study, a piezo-driven injector was applied to a high pressure common-rail type fuel injection system for the control capability of the high pressure injector’s needle and firstly examined the piezo-electric characteristics of a piezo-driven injector. Also in order to analyze the effect of injector’s needle response driven by different driving method on the injection, we investigated the diesel spray characteristics in a constant volume chamber pressurized by nitrogen gas for two injectors, a solenoid-driven injector and a piezo-driven injector, both equipped with the same injection nozzle with sac type and 5-injection hole. The experimental method for spray visualization was based on back-light photography technique by utilizing a high speed framing camera. The macroscopic spray propagation was geometrically measured and characterized in term of the spray tip penetration, spray cone angle and spray tip speed. For the evaluation of the needle response of the above two injectors, we indirectly estimated the needle’s behavior with an accelerometer and injection rate measurement employing Bosch’s method was conducted. The experimental results show that the spray tip penetrations of piezodriven injector were longer, on the whole, than that of the solenoid-driven injector. Besides we found that the piezo-driven injector have a higher injection flow rate by a fast needle response and it was possible to control the injection rate slope in piezo-driven injector by altering the induced current.