首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 15 毫秒
1.
Modeling PWM DC/DC converters out of basic converter units   总被引:4,自引:0,他引:4  
An alternative approach to modeling pulsewidth-modulated (PWM) DC/DC converters out of basic converter units (BCUs) is presented in this paper. Typical PWM DC/DC converters include the well-known buck, boost, buck-boost, Cuk, Zeta, and Sepic. With proper reconfiguration, these converters can be represented in terms of either buck or boost converter and linear devices, thus, the buck and boost converters are named BCUs. The PWM converters are, consequently, categorized into buck and boost families. With this categorization, the small-signal models of these converters are readily derived in terms of h parameter (for buck family) and g parameter (for boost family). Using the proposed approach, not only can one find a general configuration for converters in a family, but one can yield the same small-signal models as those derived from the direct state-space averaging method. Additionally, modeling of quasi-resonant converters and multiresonant converters can be simplified when adopting the proposed approach  相似文献   

2.
Novel ZVT-PWM converters with active snubbers   总被引:6,自引:0,他引:6  
An active snubber cell is proposed to contrive zero-voltage-transition (ZVT) pulsewidth-modulated (ZVT-PWM) converters. Except for the auxiliary switch, all active and passive semiconductor devices in a ZVT-PWM converter operate at zero-voltage-switching (ZVS) turn on and turn off. The auxiliary switch operates at ZVS turn off and near zero current-switching (ZCS) turn on. An analytical study on a boost ZVT-PWM converter with the proposed active snubber cell is presented in detail. A 750 W 80 kHz prototype of the boost ZVT-PWM converter has been built in the laboratory to experimentally verify the analysis. Six basic ZVT-PWM converters can be easily created by attaching the proposed active snubber cells to conventional PWM converters. A detailed design procedure of the proposed active snubber cell is also presented in this paper  相似文献   

3.
A true ZCZVT commutation cell for PWM converters   总被引:11,自引:0,他引:11  
This paper introduces a true zero-current and zero-voltage transition (ZCZVT) commutation cell for DC-DC pulsewidth modulation (PWM) converters operating with an input voltage less than half the output voltage. It provides zero-current switching (ZCS) and zero-voltage switching (ZVS) simultaneously, at both turn on and turn off of the main switch and ZVS for the main diode. The proposed soft-switching technique is suitable for both minority and majority carrier semiconductor devices and can be implemented in several DC-DC PWM converters. The ZCZVT commutation cell is placed out of the power path, and, therefore, there are no voltage stresses on power semiconductor devices. The commutation cell consists of a few auxiliary devices, rated at low power, and it is only activated during the main switch commutations. The ZCZVT commutation cell, applied to a boost converter, has been analyzed theoretically and verified experimentally. A 1 kW boost converter operating at 40 kHz with an efficiency of 97.9% demonstrates the feasibility of the proposed commutation cell  相似文献   

4.
A new family of zero-current-switching (ZCS) pulsewidth-modulated (PWM) converters which uses a new ZCS-PWM switch cell is presented in this paper. The main switch and auxiliary switch operate at ZCS turn-on and turn-off, and all the passive semiconductor devices in the ZCS-PWM converter operate at zero-voltage-switching (ZVS) turn-on and turn-off. Besides operating at constant frequency and with reduced commutation losses, these new converters have no additional current stress in comparison to the hard-switching converter counterpart. The new family of ZCS-PWM converters is suitable for high-power applications using insulated gate bipolar transistors (IGBTs). The PWM switch model and state-space averaging approach is used to estimate and examine the steady-state and dynamic character of the system. The principle of operation, theoretical analysis, and experimental results of the new ZCS-PWM boost converter, rated 1 kW and operating at 30 kHz, are provided in this paper to verify the performance of this new family of converters.  相似文献   

5.
A new family of zero-current-switching (ZCS) pulsewidth-modulation (PWM) converters using a new ZCS-PWM auxiliary circuit is presented in this paper. The main switch and auxiliary switch operate at ZCS turn-on and turn-off, and the all-passive semiconductor devices in the ZCS-PWM converters operate at zero-voltage-switching (ZVS) turn-on and turn-off. Besides operating at constant frequency and reducing commutation losses, these new converters have no additional current stress and conduction loss in the main switch in comparison to the hard-switching converter counterpart. The PWM switch model and state-space averaging approach is used to estimate and examine the steady-state and dynamic character of the system. The new family of ZCS-PWM converters is suitable for high-power applications using insulated gate bipolar transistors (IGBTs). The principle of operation, theoretical analysis, and experimental results of the new ZCS-PWM boost converter, rated 1.6 kW and operating at 30 kHz, are provided in this paper to verify the performance of this new family of converters.  相似文献   

6.
High-frequency quasi-resonant converter technologies   总被引:4,自引:0,他引:4  
Resonant switch topologies operating under the principle of zero-current switching (ZCS) and zero-voltage switching (ZVS) are introduced to minimize switching losses, stresses, and noises. Using the resonant switch concept, a host of new quasi-resonant converters (QRCs) are derived from conventional PWM converters. They are capable of operating in the megahertz range, with a significant improvement in performance and power density. Performances of ZCS and ZVS QRCs are compared. Power stages, gate drives, and feedback controls are discussed  相似文献   

7.
This paper proposes a new zero-current-switching (ZCS) pulsewidth modulation (PWM) switch cell that has no additional conduction loss of the main switch. In this cell, the main switch and the auxiliary switch turn on and turn off under zero-current condition. The diodes commutate softly and the reverse-recovery problems are alleviated. The conduction loss and the current stress of the main switch are minimized, since the resonating current for the soft switching does not flow through the main switch. Based on the proposed ZCS PWM switch cell, a new family of DC-to-DC PWM converters is derived. The new family of ZCS PWM converters is suitable for the high-power applications employing insulated gate bipolar transistors. Among the new family of DC-to-DC PWM converters, a boost converter was taken as an example and has been analyzed. Design guidelines with a design example are described and verified by experimental results from the 2.5 kW prototype boost converter operating at 40 kHz  相似文献   

8.
A new family of zero-voltage-switching (ZVS) pulsewidth-modulated (PWM) converters that uses a new ZVS-PWM switch cell is presented in this paper. Except for the auxiliary switch, all active and passive semiconductor devices in the ZVS-PWM converters operate at ZVS turn ON and turn OFF. The auxiliary switch operates at zero-current-switching (ZCS) turns ON and OFF. Besides operating at constant frequency, these new converters have no overvoltage across the switches and no additional current stress on the main switch in comparison to the hard-switching converter counterpart. Auxiliary components rated at very small current are used. The principle of operation, theoretical analysis, and experimental results of the new ZVS-PWM boost converter, rated 1 kW, and operating at 80 kHz, are provided in this paper to verify the performance of this new family of converters.  相似文献   

9.
A method for systematic synthesis of quasi-resonant (QR) topologies by addition of resonant elements to a parent pulse-width modulation (PWM) converter network is proposed. It is found that there are six QR classes with two resonant elements, including two novel classes. More complex QR converters can be generated by a recursive application of the synthesis method. Topological definitions of all known and novel QR classes follow directly from the synthesis method and topological properties of PWM parents. The synthesis of QR converters is augmented by a study of possible switch realizations and operating modes. In particular, it is demonstrated that a controllable rectifier can be used to accomplish the constant-frequency control in all QR classes. Links between the QR converters and the underlying PWM networks are extended to general DC and small-signal AC models in which the model of the PWM parent is explicitly exposed. Results of steady-state analyses of selected QR classes and operating modes include boundaries of operating regions, DC characteristics, a comparison of switching transitions and switch stresses, and a discussion of relevant design trade-offs  相似文献   

10.
This paper presents a new family of pulsewidth-modulated (PWM) converters, featuring soft commutation of the semiconductors at zero current (ZC) in the transistors and zero voltage (ZV) in the rectifiers. Besides operating at constant frequency and with reduced commutation losses, these new converters have output characteristics similar to the hard-switching-PWM counterpart, which means that there is no circulating reactive energy that would cause large conduction losses. The new family of zero-current-switching (ZCS)-PWM converters is suitable for high-power applications using insulated gate bipolar transistors (IGBTs). The advantages of the new ZCS-PWM boost converter employing IGBTs, rated at 1.6 kW and operating at 20 kHz, are presented. This new ZCS operation can reduce the average total power dissipation in the semiconductors practically by half, when compared with the hard-switching method. This new ZCS-PWM boost converter is suitable for high-power applications using IGBTs in power-factor correction. The principle of operation, theoretical analysis, and experimental results of the new ZCS-PWM boost converter are provided in this paper to verify the performance of this new family of converters  相似文献   

11.
A passive lossless snubber cell is proposed to improve the turn-on and turnoff transients of the MOSFETs in nonisolated pulsewidth modulated (PWM) DC/DC converters. Switching losses and EMI noise are reduced by restricting di/dt of the reverse-recovery current and dv/dt of the drain-source voltage. The MOSFET operates at zero-voltage-switching (ZVS) turnoff and near zero-current-switching (ZCS) turn-on. The freewheeling diode is also commutated under ZVS. As an example, operation principles, theoretical analysis, relevant equations, and experimental results of a boost converter equipped with the proposed snubber cell are presented in detail. Efficiency of 96% has also been measured in the experimental results reported for a 1 kW 100 kHz prototype in the laboratory, Six basic nonisolated PWM DC/DC converters (buck, boost, buck-boost, Cuk, Sepic, and Zeta) equipped with the proposed general snubber cells are also shown in this paper  相似文献   

12.
A new zero-voltage and zero-current-switching (ZVZCS) full-bridge (FB) pulse width modulation (PWM) power converter is proposed to improve the performance of the previously presented ZVZCS FB PWM power converters. By adding a secondary active clamp and controlling the clamp switch moderately, ZVS (for leading-leg switches) and ZCS (for lagging-leg switches) are achieved without adding any lossy components or the saturable reactor. Many advantages, including simple circuit topology, high efficiency and low cost, make the new power converter attractive for high-voltage and high-power (>10 kW) applications. The principle of operation is explained and analyzed. The features and design considerations of the new power converter are also illustrated and verified on a 1.8 kW 100 kHz IGBT-based experimental circuit  相似文献   

13.
This paper proposes a soft-single-switched forward converter with low current and voltage stresses and two derived converters. These converters operate with a nondissipative snubber in ZCS mode at turning on and ZVS mode at turning off. The output voltage is controlled by using PWM technique. It is carried out a detailed study, where operating principles and some simulation and experimental results are presented.  相似文献   

14.
Employing a saturable core in the development of zero-voltage-switching (ZVS) technique has attracted widespread attention. However, these analyses are focused on the discussions of the uncontrollable ZVS pulsewidth modulation (PWM) converters. In this paper, the characteristics after the addition of the control circuits to the ZVS saturable-core PWM converters are considered. The small-signal models of the controllable ZVS saturable-core PWM converters are also proposed. Furthermore, a proper compensation strategy is offered to achieve a stable and satisfactory dynamic response. Self-excited ZVS PWM resonant regulators with the control scheme are eventually implemented to verify theoretical derivations  相似文献   

15.
An improved ZCS-PWM commutation cell for IGBT's application   总被引:3,自引:0,他引:3  
An improved zero-current-switching pulsewidth-modulation (ZCS-PWM) commutation cell is proposed, which is suitable for high-power applications using insulated gate bipolar transistors (IGBTs) as the power switches. It provides ZCS operation for active switches with low-current stress without voltage stress and PWM operating at constant frequency. The main advantage of this cell is a substantial reduction of the resonant current peak through the main switch during the commutation process. Therefore, the RMS current through it is very close to that observed in the hard-switching PWM converters. Also, small ratings auxiliary components can be used. To demonstrate the feasibility of the proposed ZCS-PWM commutation cell, it was applied to a boost converter. Operating principles, theoretical analysis, design guidelines and a design example are described and verified by experimental results obtained from a prototype operating at 40 kHz, with an input voltage rated at 155 V and 1 kW output power. The measured efficiency of the improved ZCS-PWM boost converter is presented and compared with that of hard-switching boost converter and with some ZCS-PWM boost converters presented in the literature. Finally, this paper presents the application of the proposed soft-switching technique in DC-DC nonisolated power converters  相似文献   

16.
The purpose of this paper is to introduce a new family of zero-voltage switching (ZVS) pulse-width modulation (PWM) active-clamping DC-to-DC boost power converters. This technique presents ZVS commutation without additional voltage stress and a significant increase in the circulating reactive energy throughout the power converters. So, the efficiency and the power density become advantages when compared to the hard-switching boost power converter. Thus, these power converters may become very attractive in power factor correction applications. In this paper, the complete family of boost power converters is shown, and one particular circuit, taken as an example, is analyzed, simulated and experimented. Experimental results are presented, taken from a laboratory prototype rated at 1600 W, input voltage of 300 V, output voltage of 400 V, and operating at 100 kHz. The measured efficiency at full load was 98%, and the power converter kept an efficiency up to 95% from 17% to 100% of full load, without additional voltage and current stresses  相似文献   

17.
Multi-loop control for quasi-resonant converters   总被引:2,自引:0,他引:2  
A multiloop control scheme for quasi-resonant converters (QRCs) is described. Like current-mode control for pulse width modulation (PWM) converters, this control offers excellent transient response and replaces the voltage-controlled oscillator (VCO) with a simple comparator. In this method, referred to as current-sense frequency modulation (CSFM), a signal proportional to the output-inductor current is compared with an error voltage signal to modulate the switching frequency. The control can be applied to either zero-voltage-switched (ZVS) or zero-current-switched (ZCS) QRCs. Computer simulation is method applied to a ZCS buck QRC. A circuit implementation is presented that allows multiloop control to be used on circuits switching up to 10 MHz. This circuit requires few components and produces clean control waveforms. Experimental results are presented for zero-current flyback and zero-voltage buck QRCs, operating at up to 7 MHz. Good small-signal characteristics have been obtained  相似文献   

18.
Asymmetric control scheme is an approach to achieve zero-voltage switching (ZVS) for half-bridge isolated dc-dc converters. However, it is not suited for wide range of input voltage due to the uneven voltage and current components stresses. This paper presents a novel "duty-cycle-shifted pulse-width modulated" (DCS PWM) control scheme for half-bridge isolated dc-dc converters to achieve ZVS operation for one of the two switches without causing the asymmetric penalties in the asymmetric control and without adding additional components. Based on the DCS PWM control scheme, an active-clamp branch comprising an auxiliary switch and a diode is added across the isolation transformer primary winding in the half-bridge converter to achieve ZVS for the other main switch by utilizing energy stored in the transformer leakage inductance. Moreover, the auxiliary switch also operates at ZVS and zero-current switching (ZCS) conditions. Furthermore, during the off-time period, the ringing resulted from the oscillation between the transformer leakage inductance and the junction capacitance of two switches is eliminated owing to the active-clamp branch and DCS PWM control scheme. Hence, switching losses and leakage-inductance-related losses are significantly reduced, which provides the converter with the potential to operate at higher efficiencies and higher switching frequencies. The principle of operation and key features of the proposed DCS PWM control scheme and two ZVS half-bridge topologies are illustrated and experimentally verified.  相似文献   

19.
A novel zero voltage and zero current switching (ZVZCS) full bridge (FB) pulse width modulation (PWM) converter is proposed to improve the demerits of the previously presented ZVZCS-FB-PWM converters, such as use of lossy components or additional active switches. A simple auxiliary circuit which includes neither lossy components nor active switches provides ZVZCS conditions to primary switches, ZVS for leading-leg switches and ZCS for lagging-leg switches. Many advantages including simple circuit topology, high efficiency, and low cost make the new converter attractive for high power (>2 kW) applications. The operation, analysis, features and design considerations are illustrated and verified on a 2.5 kW, 100 kHz insulated gate bipolar transistor (IGBT) based experimental circuit  相似文献   

20.
设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号