载体氧化铝的粒径对对硝基苯酚加氢催化剂Ni/Al2O3的影响

The catalytic hydrogenation of p-nitrophenol to p-aminophenol was investigated over Ni/Al2O3 catalyst on alumina support with different particle size. It is found that support particle size has significant influences on physiochemical properties and catalytic activity of the resulting Ni/Al2O3 catalyst, but little influence on the selec-tivity. At a comparable amount of Ni loading, the catalytic activity of Ni/Al2O3 prepared with alumina support of smaller particle size is lower. The reduction behavior of the catalyst is a key factor in determining the catalytic activity of Ni/Al2O3 catalyst. The supported nickel catalyst 10.3Ni/Al2O3-3 improves the life span of the membrane by reducing fouling on the membrane surface compared to nano-sized nickel.     

以类水滑石为前体的Ni催化剂及其催化甲烷水蒸气重整制氢:催化活性和动力学(英文)

Ni/Mg–Al catalysts derived from hydrotalcite-type precursors were prepared by a co-precipitation technique and applied to steam reforming of methane. By comparison with Ni/γ-Al2O3 and Ni/α-Al2O3 catalysts prepared by in-cipient wetness impregnation, the Ni/Mg–Al catalyst presented much higher activity as a result of higher specific surface area and better Ni dispersion. The Ni/Mg–Al catalyst with a Ni/Mg/Al molar ratio of 0.5:2.5:1 exhibited the highest activity for steam methane reforming and was selected for kinetic investigation. With external and inter-nal diffusion limitations eliminated, kinetic experiments were carried out at atmospheric pressure and over a temperature range of 823–973 K. The results demonstrated that the overal conversion of CH4 and the conversion of CH4 to CO2 were strongly influenced by reaction temperature, residence time of reactants as wel as molar ratio of steam to methane. A classical Langmuir–Hinshelwood kinetic model proposed by Xu and Froment (1989) fitted the experimental data with excellent agreement. The estimated adsorption parameters were consistent thermodynamical y.     

Oxidative desulfurization of dibenzothiophene over Fe promoted Co–Mo/Al_2O_3 and Ni–Mo/Al_2O_3 catalysts using hydrogen peroxide and formic acid as oxidants

This work reports the enhancing effect of a highly cost effective and efficient metal, Fe, incorporation to Co or Ni based Mo/Al_2O_3 catalysts in the oxidative desulfurization(ODS) of dibenzothiophene(DBT) using H_2O_2 and formic acid as oxidants. The influence of operating parameters i.e. reaction time, catalyst dose, reaction temperature and oxidant amount on oxidation process was investigated. Results revealed that 99% DBT conversion was achieved at 60 °C and 150 min reaction time over Fe–Ni–Mo/Al_2O_3. Fe tremendously enhanced the ODS activity of Co or Ni based Mo/Al_2O_3 catalysts following the activity order: Fe–Ni–Mo/Al_2O_3 NFe–Co–Mo/Al_2O_3 NNi–Mo/Al_2O_3 NCo–Mo/Al_2O_3, while H_2O_2 exhibited higher oxidation activity than formic acid over all catalyst systems. Insight about the surface morphology and textural properties of fresh and spent catalysts were achieved using scanning electron microscopy(SEM), X-ray diffraction(XRD), energy dispersive X-ray(EDX)analysis, Atomic Absorption Spectroscopy(AAS) and BET surface area analysis, which helped in the interpretation of experimental data. The present study can be deemed as an effective approach on industrial level for ODS of fuel oils crediting to its high efficiency, low process/catalyst cost, safety and mild operating condition.     

WP/γ-Al2O3催化剂的制备、表征及加氢脱硫和加氢脱氮活性

Two series of WP/Al2O3 catalyst precursors with WP mass loading in the range 18.5%-37.1% were prepared using the impregnation method and mixing method, respectively, and the catalysts were then obtained by temperature-programmed reduction of supported tungsten phosphate (precursor of WP/Al2O3 catatlysts) in H2 at 650℃ for 4h. The catalysts were characterized by XRD, BET, TG/DTA, XPS and 31p MAS-NMR. The activities of these catalysts were tested in the hydrodenitrogenation (HDN) of pyridine and hydrodesulfurization (HDS) of thiophene at 340℃ and 3.0MPa. The results showed that owing to the stronger interaction of the support with the active species, the precursor of WP/Al2O3 catalyst was more difficultly phosphided and a greater amount of W species was in a high valence state W6 on the surface of the catalyst prepared by the impregnation method than that by the mixing method. 31p MAS-NMR results indicated that 31p shift from 85% H3PO4 of 2.55 × 10-4 for WP and 2.57 × 10-4 for WP/γ-Al2O3 catalysts prepared by mixing method. Such WP/Al2O3 catalysts showed higher HDN activities and lower HDS activities than those prepared by the impregnation method under the same loading of WP.WP/γ-Al2O3 catalysts with weak interaction between support and active species were favorable for HDN reaction while the WP/γ-Al2O3 catalysts with strong interaction were favorable for HDS reaction.     

n-Decane hydro-conversion over bi- and tri-metallic Al-HMS catalyst in a mini-reactor

Bi-metallic(Pt–Sn and Sn–Ni) and tri-metallic(Pt–Sn–Ni) catalysts,supported on Al-containing hexagonal mesoporous silica(Al-HMS)(Si/Al = 20) materials,were synthesized.N_2 adsorption–desorption,X-ray diffraction(XRD),Brunauer–Emmett–Teller(BET) test,and temperature programed desorption(NH3-TPD)were used to characterize physicochemical characteristics and textural properties of the Al-HMS catalysts.Catalytic performances on hydro-cracking of n-decane at different reaction conditions were studied in a microreactor.Comparison between Pt–Sn,Sn–Ni and Pt–Sn–Ni catalyst under different hydro-cracking conditions was made.The experimental results indicate that the proper balance between the acid and metal functions is the key in synthesizing a catalyst with a better performance in hydro-cracking.Tri-metallic catalyst exhibits the best catalytic performance in n-decane hydro-cracking than two bi-metallic catalysts.     

CO_2 methanation over TiO_2–Al_2O_3 binary oxides supported Ru catalysts

TiO_2 modified Al_2O_3 binary oxide was prepared by a wet-impregnation method and used as the support for ruthenium catalyst. The catalytic performance of Ru/TiO_2–Al_2O_3catalyst in CO_2 methanation reaction was investigated. Compared with Ru/Al_2O_3 catalyst, the Ru/TiO_2–Al_2O_3catalytic system exhibited a much higher activity in CO_2 methanation reaction. The reaction rate over Ru/TiO_2–Al_2O_3 was 0.59 mol CO_2·(g Ru)1·h-1, 3.1 times higher than that on Ru/Al_2O_3[0.19 mol CO_2·(gRu)-1·h-1]. The effect of TiO_2 content and TiO_2–Al_2O_3calcination temperature on catalytic performance was addressed. The corresponding structures of each catalyst were characterized by means of H_2-TPR, XRD, and TEM. Results indicated that the averaged particle size of the Ru on TiO_2–Al_2O_3support is 2.8 nm, smaller than that on Al_2O_3 support of 4.3 nm. Therefore, we conclude that the improved activity over Ru/TiO_2–Al_2O_3catalyst is originated from the smaller particle size of ruthenium resulting from a strong interaction between Ru and the rutile-TiO_2 support, which hindered the aggregation of Ru nanoparticles.     

Degradation analysis of A2/O combined with AgNO3+K2FeO4 on coking wastewater

In this work, a coking wastewater was selected and a biochemical A~2/O treatment device for fractional degradation was designed and employed. After each stage of the treatment, the products were analyzed through gas chromatography–mass spectroscopy(GC–MS) to determine their composition. Finally, AgNO_3+ K_2 FeO_4 was used as an advanced deep catalytic oxidation treatment. It was concluded from the analysis that cyclic organics could be degraded and the chemical oxygen demand(COD) was controlled within 50 mg·L~(-1), in line with the target value. Meanwhile, the spectra obtained from the GC–MS were in accordance with the conclusions reached based on the COD. The research results showed that all hard-degradable organics in coking wastewater could be eliminated through the A~2/O bio-membrane treatment and the advanced treatment of making use of K_2FeO_4 as an oxidant and Ag+as a catalyst, the catalytic efficiency with Ag+as a catalyst of K+2FeO_4 was very high. Agcould evidently improve the oxidation capacity of K_2FeO_4 to wastewater in its short stability time, and this is an important innovation.     

Performance characteristics of fluidized bed syngas methanation over Ni-Mg/Al2O3 catalyst

The performance characteristics of isothermal fluidized bed syngas methanation for substitute natural gas are investigated over a self-made Ni–Mg/Al2O3 catalyst. Via atmospheric methanation in a laboratory fluidized bed reactor it was clarified that the CO conversion varied in 5% when changing the space velocity in 40–120 L·g?1·h?1 but the conversion increased obviously by raising the superficial gas velocity from 4 to 12.4 cm·s?1. The temperature at 823 K is suitable for syngas methanation while obvious deposition of uneasy-oxidizing Cγoccurs on the catalyst at temperatures around 873 K. From a kinetic aspect, the lowest reaction temperature is suggested to be 750 K when the space velocity is 60 L·g?1·h?1. Raising the H2/CO ratio of the syngas increased proportionally the CO conversion and CH4 selectivity, showing that at enough high H2/CO ratios the active sites on the catalyst are sufficient for CO adsorption and in turn the reaction with H2 for forming CH4. Introducing CO2 into the syngas feed suppresses the water gas shift and Boudouard reactions and thus increased H2 consumption. The ratio of CO2/CO in syngas should be better below 0.52 because varying the ratio from 0.52 to 0.92 resulted in negligible increases in the H2 conversion and CH4 selectivity but decreased the CH4 yield. Introducing steam into the feed gas affected little the CO conversion but decreased the selectivity to CH4. The tested Ni–Mg/Al2O3 catalyst manifested good stability in structure and activity even in syngas containing water vapor.     

Effect of Al Content on the Isomerization Performance of Solid Superacid Pd-S2O82-/ZrO2-Al2O3☆

The effect of Al content on the performance of the Pd–S2O82?/ZrO2–Al2O3 solid superacid catalyst was studied using n-pentane isomerization as a probe reaction. The catalysts were also characterized by ...     

1,6-己二胺与氨基甲酸甲酯非均相CeO2催化合成1,6-己二氨基甲酸甲酯（英文）

The efficient synthesis of dimethylhexane-1,6-dicarbamate (HDC) from 1,6-hexanediamine (HDA) and methyl carbonate over a series of heterogeneous catalysts (e.g., MgO, Fe2O3, Mo2O3, and CeO2) was investigated. The reaction pathway was confirmed as an alcoholysis reaction through a series of designed experiments. Under optimized conditions, 100%HDA conversion with 83.1%HDCtotal and 16.9%polyurea was obtained using a one-step with high temperature procedure with CeO2 as the catalyst. A new two-step with variable temperature technol-ogy was developed based on the reaction pathway to reduce the polyurea yield. Using the proposed method, the HDCtotal yield reached 95.2%, whereas the polyurea yield decreased to 4.8%. The CeO2 catalyst showed high stability and did not exhibit any observable decrease in the HDC yield or any structural changes after four recycling periods. ? 2014 The Chemical Industry and Engineering Society of China, and Chemical Industry Press. Al rights reserved.     

Preparation of Ni2P/Al-SBA-15 catalyst and its performance for benzofuran hydrodeoxygenation

The Al-doped Ni2P/Al-SBA-15 catalyst with high hydrodeoxygenation(HDO)activity was synthesized by tem-perature programmed reduction at a relatively low reduction temperature of 400°C.The as-prepared catalyst was characterized by X-ray diffraction(XRD),H2temperature-programmed reduction(H2-TPR),X-ray photo-electron spectroscopy(XPS),transmission electron microscope(TEM),NH3temperature programmed desorp-tion (NH3-TPD), N2adsorption-desorption and CO uptake. The effect of Al on benzofuran (BF) HDO performance was investigated.The result indicates that the incorporation of Al into the SBA-15 support can pro-mote the formation of much uniform,smaller,highly dispersed Ni2P particles on the catalyst.The Al also contrib-utes to suppress the enrichment of P and promote more exposed Ni sites on the surface. In addition,the incorporation of Al can enhance the acid strength.The total deoxygenated product yield over Ni2P/Al-SBA-15 reached 90.3%,which is an increase of 19.4%,when compared with that found for Ni2P/SBA-15(70.9%).     

Preparation of Ni/bentonite catalyst and its applications in the catalytic hydrogenation of nitrobenzene to aniline

Ni supported on bentonite was prepared by the impregnation method with different nickel contents, applied to the hydrogenation of nitrobenzene to aniline in a fixed-bed reactor, and it was characterized by X-ray diffraction(XRD), H_2-temperature programmed reduction(H_2-TPR), and X-ray photoelectron spectrometry(XPS). The results showed that Ni/bentonite catalyst with 20 wt% nickel content provided a higher conversion of nitrobenzene and selectivity of aniline compared to other catalysts. Ni O was the precursor of the active component of the catalyst, and the small crystallite size as well as the highly dispersed Ni O on the Ni/bentonite-20 catalyst, contributed to the catalytic performance. The hydrogenation of nitrobenzene was carried out at 300 °C with a H_2 gaseous hourly space velocity of 4800 ml·(g cat)~(-1)·h~(-1)and a nitrobenzene liquid hourly space velocity of4.8 ml·(g cat)~(-1)·h~(-1)over Ni/bentonite-20. A 95.7% nitrobenzene conversion and 98.8% aniline selectivity were obtained. While the nitrobenzene liquid hourly space velocity was 4.8 ml·(g cat)~(-1)·h~(-1), the yield of aniline was more than 95.0% during a 10-hour reaction.     

Vapor phase carbonylation of ethanol with Ni-Zn/c catalyst

Vapor phase carbonylation of ethanol with Ni/C and Ni-Zn/C catalyst was investigatedunder atmospheric pressure.Ni-Zn/C was found to have a significantly higher activity andselectivity than Ni/C.Effects of Zn and Ni loading on ethanol conversion and productdistributions were also investigated,and the sequence of metal loading was compared.The cata-lyst was characterized by XRD(X-ray diffraction)and SEM-EDS.The spectra of XRDdemonstrated that the catalyst structure was changed from crystalline to non-crystalline in theprocess of carbonylation.Stable iodide compound was formed due to the interaction betweenC_2H_5I and active metals.The authors believe that the active phase of carbonylation might havebeen non-crystalline.     

La/Zn/HZSM-5催化剂上的甲醇芳构化研究

Aromatization of methanol over co-impregnated La/Zn/HZSM-5 zeolite catalyst was studied.The selectivity of aromatics and BTX(benzene,toluene,and xylene)reached 64.0%and 56.6%,respectively,using La/Zn/HZSM-5 at 437°C,0.1 MPa and methanol WHSV(weight hourly space velocity)=0.8 h-1.Catalytic results showed that the La species was a very good promoter,increased selectivity of aromatics,and prolonged the catalyst lifetime on stream.The effects of the SiO2/Al2O3 ratio in zeolite,Zn and La loading,WHSV,reaction temperature, water content in the feed and H2 pretreatment of catalysts on the catalytic performance were studied in detail. Characterizations of the catalysts by thermogravimetric analysis(TGA),NH3-TPD(temperature programmed desorption),SEM(scanning electron micrograph),N2 adsorption-desorption,XRD(X-ray diffraction)and XRF (X-ray fluorescence),were carried out to understand the structure and discuss the aromatization performance of La/Zn/HZSM-5 zeolite catalyst.     

甲烷的二氧化碳重整动力学研究

The kinetics of CO2 reforming of methane has been studied at 976-1033K on a commercial NiO/CaO/Al2O3 catalyst in a packed-bed continuous reactor. The reaction was carried out at atmospheric pressure and CO2/CH4 ratio > 2. The Hougen-Watson rate models were fitted to experimental data assuming the dissociative adsorption of methane as the rate-determining step. The reaction rate showed an effective reaction order of about unity for CH4. The apparent activity energy was found to be 104kJ·mol-1. Therefore the kinetic reaction parameters were determined and a possible reaction mechanism was proposed.     

Benzene selective hydrogenation over supported Ni (nano-) particles catalysts: Catalytic and kinetics studies

This report aims to reduce the benzene in a mixture of benzene and toluene as a model reaction using catalytic hydrogenation. In this research, we developed a series of catalysts with different supports such as Ni/HMS, Ni/HZSM-5, Ni/HZSM5-HMS, Ni/Al_2O_3 and Ni/SiO_2. Kinetic of this reaction was investigated under various hydrogen and benzene pressures. For more study, two kinetic models have also been selected and tested to describe the kinetics for this reaction. Both used models, the power law and Langmuir–Hinshelwood, provided a good fit toward the experimental data and allowed to determine the kinetic parameters. Among these catalysts, Ni/Al_2O_3 showed the maximum benzene conversion(99.19%) at 130 °C for benzene hydrogenation. The lowest toluene conversion was observed for Ni/SiO_2. Furthermore, this catalyst presented high selectivity to benzene(75.26%)at 130 °C. The catalytic performance(activity, selectivity and stability) and kinetics evaluations were shown that the Ni/SiO_2 is an effective catalyst to hydrogenate benzene. It seems that the surface properties particularly pore size are effective parameter compared to other factors such as acidity and metal dispersion in this process.     

周期性输入组分和扫气在改善钯膜反应器甲烷部分氧化制氢中的作用(英文)

The partial oxidation of methane under periodic operation over Ni/γ-Al2O3 catalyst was investigated in a Pd-membrane reactor.The effects of key parameters such as the inlet composition and the sweeping gas on methane conversion and the hydrogen recovery are numerically established with two periodic input functions.In order to analyze the effect of the inputs modulation,the reaction was performed under low steam to methane ratio at a moderate temperature and pressure.It was obtained that to achieve process intensification is to operate the process in a periodic way.The main results show that the periodic input functions can improve the performance of the process compared to the optimal steady state operation.Moreover,there is an optimum amplitude of manipulated inputs leads to a maximum of hydrogen recovery.It is noteworthy that the comparison between the predicted performance via the sinusoidal and the square ways show that the better average performance was obtained with the square way.     

Catalytic ozonation of thymol in reverse osmosis concentrate with core/shell Fe3O4@SiO2@Yb2O3 catalyst:Parameter optimization and degradation pathway

In this work, a novel catalyst of Fe_3O_4@SiO_2@Yb_2O_3 was prepared and the degradation of thymol in reverse osmosis concentrate using ozonation was explored. The operational parameters, such as ozone dosage(8–48 mg·min~(-1)),initial thymol concentration(20–100 mg·L~(-1)), initial pH value(3–11), and catalyst Fe_3O_4@SiO_2@Yb_2O_3dosage(0.2–1.0 g), were studied focusing on the thymol degradation and COD removal. The results indicated that the increase in ozone dosage, initial p H value, and Fe_3O_4@SiO_2@Yb_2O_3dosage accelerated the thymol degradation and COD removal, while the increase in initial thymol concentration hampered the effect of ozonation. A pathway of thymol degradation by catalytic ozonation was proposed based on the intermediates detected by gas chromatography-mass spectrometer and ion chromatography. This paper can provide basic data and technical alternative for pollutant removal from reverse osmosis concentrate by ozonation.     

Zn–Ca–Al mixed oxide as efficient catalyst for synthesis of propylene carbonate from urea and 1,2-propylene glycol

A series of Zn–Ca–Al oxides with different CaO and ZnO contents have been prepared and evaluated in the synthesis of propylene carbonate(PC) from 1,2-propylene glycol(PG) and urea in a batch reactor. The effect of catalyst composition, basicity and reaction process parameters such as temperature, catalyst dose, molar ratio of PG to urea, purge gas flow and reaction time has been studied to find suitable reaction conditions for the PC synthesis. The PC selectivity and yield under the desired conditions could reach 98.4% and 90.8%, respectively. The best performing catalyst also exhibited a good reusability without appreciable loss in the PC selectivity and yield after five consecutive reaction runs. In addition, a stepwise reaction pathway involving a 2-hydroxypropyl carbamate intermediate was proposed for the urea alcoholysis to PC in the presence of Zn–Ca–Al catalysts, according to the time dependences of reaction intermediates and products.     

Cobalt catalysts for Fischer–Tropsch synthesis: The effect of support,precipitant and pH value

In this report,Co-based catalysts supported on ZnO,Al_2O_3 and ZrO_2 as well as the ZrO_2 derived from different precipitants and different pH values were prepared by co-precipitation method.Their catalytic Fischer–Tropsch synthesis(FTS)performance was investigated in a fixed-bed reactor.The results revealed that Co catalyst supported on ZrO_2 exhibited better FTS catalytic performance than that supported on ZnO or Al_2O_3.For the Co/ZrO_2catalyst,different precipitants showed the following an activity order of NaOHNa_2CO_3NH_4OH,and the best pH value is 13.The catalysts were characterized by N_2adsorption–desorption,XRF,XRD,H_2-TPR,H_2-TPD and TEM.It was found that the main factor affecting the CO conversion of the catalyst was the amounts of low-temperature active adsorption sites.Moreover,the selectivity of C_5~+hydrocarbons had a positive relationship with the peak temperature of the weak hydrogen adsorption sites.The higher the peak temperature,the higher the C_5~+selectivity is.