Preparation and characterization of TiO2–SiO2 nano-composite thin films

TiO₂ nanocrystalline particles dispersed in SiO₂ have been prepared by the sol-gel method using titanium- and silicon-alkoxides as precursors. Nano-composite thin films were formed on the glass substrates by dip-coating technique and heat treated at temperatures up to 500 °C for 1 h. The size of the TiO₂ nanocrystalline particles in the TiO₂–SiO₂ solution ranged from 5 to 8 nm. The crystalline structure of TiO₂ powders was identified as the anatase phase. As the content of SiO₂ increased, the anatase phase tended to be stabilized to higher temperature. TEM results revealed the presence of spherical TiO₂ particles dispersed in a disk-shaped glassy matrix. Photocatalytic activity of the TiO₂–SiO₂ (1:1) thin films showed decomposition of 95% of methylene blue solution in 2 h and a contact angle of 10°. The photocatalytic decomposition of methylene blue increased and the contact angle decreased with the content of TiO₂ phase. TiO₂–SiO₂ with the molar ratio of 1:1 showed a reasonable combination of adhesion, film strength, and the photocatalytic activity.     

Mesostructured SiO2-doped TiO2 with enhanced thermal stability prepared by a soft-templating sol–gel route

Mesostructured SiO₂–TiO₂ mixed oxides have been prepared by a soft-templating sol–gel route, using a non-ionic triblock copolymer as structure-directing agent. Tetraethylorthosilicate (TEOS) and titanium tetraisopropoxide (TTIP) have been employed as Si and Ti sources, respectively. Using a prehydrolysis TEOS step allows mixed oxides to be produced with a homogeneous porosity and with no phase segregation, in a wide range of Si/Ti compositions. Both the hydrolysis molar ratio and the silicon content have been found to be important factors determining the final properties of these materials. For instance, mixed oxides containing low silicon concentrations exhibit N₂ physisorption isotherms typical of mesoporous materials, although with an important contribution of microporosity. On the other hand, increasing the hydrolysis molar ratio makes more difficult to reach a total dispersion of SiO₂ through the TiO₂ matrix. Even with low SiO₂ loadings, the thermal stability is effectively enhanced, when compared to the equivalent pure TiO₂ materials, as a consequence of a delay in the titania crystallization to anatase. Thus, after calcination at 300 °C for 3 h, mixed oxides containing low Si/Ti ratios (20/80) show BET surface area in the range 290–346 m²/g, while pure TiO₂ materials largely collapse under the same treatment and their BET surface area drop strongly to values around 125 m²/g. This synthesis route, therefore, provides mesoporous TiO₂-rich materials with enhanced stability and textural properties, which is of high interest for applications as catalysts and supports.     

Photoresponse and AC impedance characterization of TiO2–SiO2 mixed oxide for photocatalytic water decomposition

TiO₂–SiO₂ mixed oxides were prepared by sol–gel processes with one-stage (mix up fully hydrolyzed titania- and silica-sol), two-stage (with pre-hydrolysis) and modified two-stage synthesis routes. The photoresponse and AC impedance characterization of the derived catalysts are studied and correlated for the first time with the photocatalytic activities in water decomposition under UV illumination. Synergistic effects in terms of photocatalytic activity and electronic properties including band-gap energy, flat band potential and doping density were observed on atomically mixing TiO₂ and SiO₂ by the two-stage synthesis route. Meanwhile, the decline of photocurrent density were found on TiO₂–SiO₂ relative to bare TiO₂, which could be attributed to low quality crystalline structure of the former compared to that of the latter. The superior photocatalytic performance of TiO₂–SiO₂ is ascribed to the higher flat band potential, band-gap energy, and doping density than those of bare TiO₂.     

Hydrodesulfurization of dibenzothiophenes over molybdenum catalyst supported on TiO2–Al2O3

Composite types of TiO₂–Al₂O₃ supports, which are γ-aluminas coated by titania, have been prepared by chemical vapor deposition (CVD), using TiCl₄ as a precursor. Then supported molybdenum catalysts have been prepared by an impregnation method. As supports, we employed γ-alumina, anatase types of titania, and composite types of TiO₂–Al₂O₃ with different loadings of TiO₂. We studied the conversion of Mo from oxidic to sulfidic state through sulfurization by X-ray photoelectron spectroscopy (XPS). The obtained spectra unambiguously revealed the higher reducibility from oxidic to sulfidic molybdenum species on the TiO₂ and TiO₂–Al₂O₃ supports compared to that on the Al₂O₃ support. Higher TiO₂ loadings of the TiO₂–Al₂O₃ composite support led to higher reducibility for molybdenum species. Furthermore, the catalytic behavior of supported molybdenum catalysts has been investigated for hydrodesulfurization (HDS) of dibenzothiophene (DBT) and methyl-substituted DBT derivatives. The conversion over the TiO₂–Al₂O₃ supported Mo catalysts, in particular for the 4,6-dimethyl-DBT, is much higher than that obtained over Al₂O₃ supported Mo catalyst. The ratio of the corresponding cyclohexylbenzene (CHB)/biphenyl (BP) derivatives is increased over the Mo/TiO₂–Al₂O₃. This indicates that the prehydrogenation of an aromatic ring plays an important role in the HDS of DBT derivatives over TiO₂–Al₂O₃ supported catalysts.     

Improvement of catalytic activity and sulfur-resistance of Ag/TiO2–Al2O3 for NO reduction with propene under lean burn conditions

Ag-based catalysts supported on various metal oxides, Al₂O₃, TiO₂, and TiO₂–Al₂O₃, were prepared by the sol–gel method. The effect of SO₂ on catalytic activity was investigated for NO reduction with propene under lean burn condition. The results showed the catalytic activities were greatly enhanced on Ag/TiO₂–Al₂O₃ in comparison to Ag/Al₂O₃ and Ag/TiO₂, especially in the low temperature region. Application of different characterization techniques revealed that the activity enhancement was correlated with the properties of the support material. Silver was highly dispersed over the amorphous system of TiO₂–Al₂O₃. NO₃⁻ rather than NO₂⁻ or NOx reacted with the carboxylate species to form CN or NCO. NO₂ was the predominant desorption species in the temperature programmed desorption (TPD) of NO on Ag/TiO₂–Al₂O₃. More amount of formate (HCOO⁻) and CN were generated on the Ag/TiO₂–Al₂O₃ catalyst than the Ag/Al₂O₃ catalyst, due to an increased number of Lewis acid sites. Sulfate species, resulted from SO₂ oxidation, played dual roles on catalytic activity. On aged samples, the slow decomposition of accumulated sulfate species on catalyst surface led to poor NO conversion due to the blockage of these species on active sites. On the other hand, catalytic activity was greatly enhanced in the low temperature region because of the enhanced intensity of Lewis acid site caused by the adsorbed sulfate species. The rate of sulfate accumulation on the Ag/TiO₂–Al₂O₃ system was relatively slow. As a consequence, the system showed superior capability for selective adsorption of NO and SO₂ toleration to the Ag/Al₂O₃ catalyst.     

Preparation and characterization of surface bond-conjugated TiO2/SiO2 and photocatalysis for azo dyes

Surface bond-conjugated TiO₂/SiO₂ was prepared by means of the impregnation method. Based on the results of XRD, FTIR, XPS and BET measurements, the growth of titania (predominantly anatase) on the silica substrate seems to occur by anchoring of the TiO₂ phase through Ti–O–Si cross-linking bonds. The structure model of TiO₂/SiO₂ was proposed. Compared to B–TiO₂, the most efficient catalyst is 30 wt.% TiO₂/SiO₂ (Ims30), which showed three times higher photoactivity for the degradation of reactive 15 (R15). In addition, the catalyst had a higher photoactivity on a silica of smaller particle size than on the silica of larger particles. Silica gel plays the basic role of dispersion and support for power TiO₂. The isoelectric point of the catalyst was 3.0 pH units by the measurement of zeta-potential, indicating the presence of the surface acidity of the catalyst. The photodegradation and the adsorption of R15 and cationic blue X-GRL (CBX) were investigated with the change of initial aqueous pH.     

Catalytic activity of dispersed CuO phases towards nitrogen oxides (N2O, NO, and NO2)

A systematic reactivity study of N₂O, NO, and NO₂ on highly dispersed CuO phases over modified silica supports (SiO₂–Al₂O₃, SiO₂–TiO₂, and SiO₂–ZrO₂) has been performed. Different reaction paths for the nitrogen oxide species abatement were studied: from direct decomposition (N₂O) to selective reductions by hydrocarbons (N₂O, NO, and NO₂) and oxidation (NO to NO₂). The oxygen concentration, temperature, and contact time, were varied within suitable ranges in order to investigate the activity and in particular the selectivity in the different reactions studied. The support deeply influenced the catalytic properties of the active copper phase. The most acidic supports, SiO₂–Al₂O₃ and SiO₂–ZrO₂, led to a better activity and selectivity of CuO for the reactions of N₂O, NO, and NO₂ reductions and N₂O decomposition than SiO₂–TiO₂. The catalytic results are discussed in terms of actual turnover frequencies starting from the knowledge of the copper dispersion values.     

Phase diagram of the Al2O3–ZrO2–Nd2O3 system

The phase diagram of the Al₂O₃–ZrO₂–Nd₂O₃ system was constructed in the temperature range 1250–2800 °C. The liquidus surface of the phase diagram reflects the preferentially eutectic interaction in the system. Two new ternary and one new binary eutectics were found. The minimum melting temperature is 1675 °C and it corresponds to the ternary eutectic Nd₂O₃·11Al₂O₃ + F-ZrO₂ + NdAlO₃. The solidus surface projection and the schematic of the alloy crystallization path confirm the preferentially congruent character of phase interaction in the ternary system. The polythermal sections present the complete phase diagram of the Al₂O₃–ZrO₂–Nd₂O₃ system. No ternary compounds or regions of remarkable solid solution were found in the components or binaries in this ternary system.     

Catalytic activities of Co(Ni)Mo/TiO2–Al2O3 catalysts in gasoil and thiophene HDS and pyridine HDN: effect of the TiO2–Al2O3 composition

The effect of the TiO₂–Al₂O₃ mixed oxide support composition on the hydrodesulfurization (HDS) of gasoil and the simultaneous HDS and hydrodenitrogenation (HDN) of gasoil+pyridine was studied over two series of CoMo and NiMo catalysts. The intrinsic activities for gasoil HDS and pyridine HDN were significantly increased by increasing the amount of TiO₂ into the support, and particularly over rich- and pure-TiO₂-based catalysts. It is suggested that the increase in activity be due to an improvement in reducing and sulfiding of molybdena over TiO₂. The inhibiting effect of pyridine on gasoil HDS was found to be similar for all the catalysts, i.e., was independent of the support composition. The ranking of the catalysts for the gasoil HDS test differed from that obtained for the thiophene test at different hydrogen pressures. In the case of gasoil HDS, the activity increases with TiO₂ content and large differences are observed between the catalysts supported on pure Al₂O₃ and pure TiO₂. In contrast, in the case of the thiophene test, the pure Al₂O₃-based catalyst appeared relatively more active than the catalysts supported on mixed oxides. Also, in the thiophene test the difference in intrinsic activity between the pure Al₂O₃-based catalyst appeared relatively more active than the catalysts supported on mixed oxides. Also in the thiophene test, the difference in intrinsic activity between the pure Al₂O₃- and pure TiO₂-based catalysts is relatively small and dependent on the H₂ pressure used. Such differences in activity trend among the gasoil and the thiophene tests are due to a different sensitivity of the catalysts (by different support or promoter) to the experimental conditions used. The results of the effect of the H₂ partial pressure on the thiophene HDS, and on the effect of H₂S concentration on gasoil HDS demonstrate the importance of these parameters, in addition to the nature of the reactant, to perform an adequate catalyst ranking.     

Direct decomposition of nitric oxide over Ba catalysts supported on CeO2-based mixed oxides

The direct decomposition of nitric oxide (NO) over barium catalysts supported on various metal oxides was examined in the absence and presence of O₂. Among the Ba catalysts supported on single-component metal oxides, Ba/Co₃O₄ and Ba/CeO₂ showed high NO decomposition activities, while Ba/Al₂O₃, Ba/SiO₂, and Ba/TiO₂ exhibited quite low activities. The effect of an addition of second components to Co and Ce oxides was further examined, and it was found that the activities were significantly enhanced using Ce–Mn mixed oxides as support materials. XRD results indicated the formation of CeO₂–MnO_x solid solutions with the cubic fluorite structure. O₂-TPD of the CeO₂–MnO_x solid solutions showed a large desorption peak in a range of relatively low temperature. The BET surface areas of the CeO₂–MnO_x solid solutions were larger than those of pure CeO₂ and Mn₂O₃. These effects caused by the addition of Mn are responsible for the enhanced activities of the Ba catalysts supported on Ce–Mn mixed oxides.     

Reduction of SO2 by CO to elemental sulfur over Co3O4–TiO2 catalysts

Mixed oxides of Co₃O₄–TiO₂ have shown the highest catalytic activity for the reduction of SO₂ by CO among catalysts that have been developed so far. Almost zero conversion was observed with cobalt alone, whereas a high conversion was obtained with TiO₂ especially at high temperatures. There existed a strong synergistic promotional effect in the conversion of SO₂ when cobalt was mixed with TiO₂. The synergistic effect observed with mixed oxides is caused by simultaneous contributions from two different reaction routes via COS intermediate mechanism and modified redox mechanism. The synergistic effect that is caused by the COS mechanism has a smaller amount of contribution in the conversion increase and remains almost constant with an increase in the reaction temperature. A larger portion of the synergistic effect is contributed from the modified redox mechanism especially at low temperatures, but the effect disappears at temperatures above 450°C. It is found that the introduction of cobalt into TiO₂ produces COS by the reaction between sulfided CoS₂ and CO even at low temperatures. The COS intermediate can react with SO₂ to produce an additional sulfur via the COS intermediate mechanism, and also behaves as a strong reductant to keep oxygen vacancies on the TiO₂ in a high concentration for the production of sulfur via modified redox mechanism.     

Hydrodesulfurization activity of CoMo and NiMo supported on Al2O3–TiO2 for some model compounds and gas oils

Catalytic activities of Al₂O₃–TiO₂ supporting CoMo and NiMo sulfides (CoMoS and NiMoS) catalysts were examined in the transalkylation of isopropylbenzene and hydrogenation of naphthalene as well as the hydrodesulfurization (HDS) of model sulfur compounds, conventional gas oil (GO), and light cycle oil (LCO). Al₂O₃–TiO₂ supporting catalysts exhibited higher activities for these reactions except for the HDS of the gas oil than a reference Al₂O₃ supporting catalyst, indicating the correlation of these activities. Generally, more content of TiO₂ promoted the activities. Inferior activity of the catalyst for HDS of the gas oil is ascribed to its inferior activity for HDS of dibenzothiophene (DBT) in gas oil as well as in model solvent decane, while the refractory 4,6-dimethyldibenzothiophene (4,6-DMDBT) in gas oil as well as in decane was more desulfurized on the catalyst. Characteristic features of Al₂O₃–TiO₂ catalyst are discussed based on the paper results.     

Fischer–Tropsch synthesis over Re-promoted Co supported on Al2O3, SiO2 and TiO2: Effect of water

The activity and selectivity of rhenium promoted cobalt Fischer–Tropsch catalysts supported on Al₂O₃, TiO₂ and SiO₂ have been studied in a fixed-bed reactor at 483 K and 20 bar. Exposure of the catalysts to water added to the feed deactivates the Al₂O₃ supported catalyst, while the activity of the TiO₂ and SiO₂ supported catalysts increased. However, at high concentrations of water both the SiO₂ and TiO₂ supported catalyst deactivated. Common for all catalysts was an increase in C₅₊ selectivity and a decrease in the CH₄ selectivity by increasing the water partial pressure. The catalysts have been characterized by scanning transmission electron microscope (STEM), BET, H₂ chemisorption and X-ray diffraction (XRD).     

Densification and phase transformation of Si3N4 in the presence of mechanically activated BaCO3–Al2O3–SiO2 mixture

Densification as well as the →β phase transformation of Si₃N₄ were monitored as a function of activation time of the BaCO₃–Al₂O₃–SiO₂ additive mixture. The composition of the ternary mixture corresponded to celsian (BaAl₂Si₂O₈—BAS). Previously, mechanically activated powder mixtures for various lengths of time were added to Si₃N₄ in the amount of 10–30%. Sintering was performed at 1650–1700°C in nitrogen atmosphere up to 8 h. The changes in densification degree, as well as phase composition, were followed as a function of heating time and the time of mechanical activation of the additive mixture. The results obtained showed that mechanical activation retarded densification in samples heated up to 1700°C. On the other hand, for the constant sintering time, →β transformation of Si₃N₄ was enhanced with increasing activation time, and the amount of additives.     

Carbon reduction reaction in the Y2O3–SiO2 glass system at high temperature

In order to assess the role of carbon with respect to the grain boundary chemistry of Si₃N₄-based ceramics model experiments were performed. Y₂O₃–SiO₂ glass systems with various amount of carbon (from 1 to 30 wt.%) were prepared by high-temperature treatment in a graphite furnace. High carbon activity of the furnace atmosphere was observed. EDX analysis proved the formation of SiC by the carbothermal reduction of SiO₂ either in the melt or in the solid state. The melting temperature of the Y₂O₃–SiO₂ system is strongly dependent on the amount of reduced SiO₂. XRD analysis of the products documented the presence of Y₂Si₂O₇, Y₂SiO₅ and Y₂O₃ crystalline phases in that order with an increasing amount of free C in the starting mixture. The reduction of Y₂O₃ was not confirmed.     

Grain growth in TiO2-added ZnO–Bi2O3–CoO–MnO ceramics prepared by chemical processing

The effect of TiO₂ on the grain growth of the ZnO–Bi₂O₃–CoO–MnO ceramic system prepared by chemical coprecipitation, was studied between 1150 and 1300 °C in air. Bi₂O₃ melts during firing, and then TiO₂ dissolves into Bi₂O₃-rich liquid. TiO₂ initially reacts with Bi₂O₃ to form Bi₄Ti₃O₁₂. Above ≈1050 °C, Bi₄Ti₃O₁₂ reacts with ZnO to form Zn₂TiO₄ spinel phase. The kinetic study of grain growth carried out using the expression Gⁿ–G_oⁿ=K_o·t·exp(−Q/RT) gave grain exponent (n) value as 6 and the apparent activation energy (Q) as 226.46 kJ/mol. 1.00 mol% TiO₂ addition increased the grain growth exponent value from 6 to 7 and apparent activation energy with 1.00 mol% TiO₂ addition was found to be 197.10 kJ/mol. The ZnO grain size gradually increases with increasing TiO₂ content. Addition of TiO₂ may increase the reactivity of the Bi₂O₃-rich liquid towards the ZnO grain, thus affecting the ZnO grain growth.     

Effect of the local structure of Ti-oxide species on the photocatalytic reactivity and photo-induced super-hydrophilic properties of Ti/Si and Ti/B binary oxide thin films

From the results of various spectroscopic investigations of Ti-oxide-based binary oxides, it was found that tetrahedrally coordinated Ti-oxide species are formed in the thin films of Ti/Si binary oxides with low TiO₂ content, while octahedrally coordinated TiO₂ nano-particles are formed in the Ti/B binary oxide thin films, reflecting the effect of the crystalline structures of the host SiO₂ or B₂O₃ on the local structure of the guest Ti-oxide species, respectively. The photocatalytic reactivity of the TiO₂ thin films was found to be remarkably enhanced by the dispersion of the Ti-oxide moiety into both the SiO₂ and B₂O₃ matrices, whereas the photo-induced super-hydrophilic properties of the TiO₂ thin films were enhanced only by a combination or mixing of the Ti-oxide moiety with B₂O₃.     

Evaluation of V2O5–WO3–TiO2 and alternative SCR catalysts in the abatement of VOCs

Two different commercial SCR catalysts belonging to the V₂O₅–WO₃–TiO₂ system, and different alternative catalysts based on Mn, Fe, Cr, Al and Ti oxides have been tested in the conversion of VOCs in excess oxygen in a temperature range typical of the SCR process (500–700 K). Propane, propene, isopropanol, acetone, 2-chloropropane and 1,2-dichlorobenzene have been fed with excess oxygen and helium. The industrial catalysts are poorly active in the conversion of propane, giving mainly rise to propene by oxy-dehydrogenation. The conversion of propene is higher with CO as the predominant product. In any case, the oxidation activity depends on the vanadium content of the catalyst. Isopropanol is mainly converted into acetone and propene, while acetone is burnt predominantly to CO. Mn- and Fe- containing systems are definitely more active in the conversion of hydrocarbons and oxygenates, giving rise almost exclusively to CO₂. 2-Chloropropane is selectively dehydrochlorinated to propene and HCl starting from 350 K, propene being later burnt to CO on the industrial V₂O₅–WO₃–TiO₂ catalysts, whose combustion activity is, apparently, not affected by chlorine. On the contrary, chlorine strongly affects the behavior of Mn-based catalysts, that are active in the dehydrochlorination of 2-chloropropane, but are simultaneously deactivated with respect to their combustion catalytic activity. The conversion of 1,2-dichlorobenzene gives rise to important amounts of heavy products in our experimental conditions with relatively high reactant concentration.     

Strong rhodium–niobia interaction in Rh/Nb2O5, Nb2O5–Rh/SiO2 and RhNbO4/SiO2 catalysts: Application to selective CO oxidation and CO hydrogenation

The extent of Rh–niobia interaction in niobia-supported Rh (Rh/Nb₂O₅), niobia-promoted Rh/SiO₂ (Nb₂O₅–Rh/SiO₂) and RhNbO₄/SiO₂ catalyst after H₂ reduction has been investigated by H₂ and CO chemisorption measurements. These catalysts have been applied to selective CO oxidation in H₂ (CO+H₂+O₂) and CO hydrogenation (CO+H₂), and the results are compared with those of unpromoted Rh/SiO₂ catalysts. It has been found that niobia (NbO_x) increases the activity and selectivity for both the reactions.     

Characterization and photocatalytic activity of transition-metal-supported surface bond-conjugated TiO2/SiO2

TM/TiO₂/SiO₂ photocatalysts were prepared by the photodeposition method using transition metal salts (TM=Fe³⁺, Co²⁺, Ni²⁺ and Cu²⁺) as precursors and the surface bond-conjugated TiO₂/SiO₂ as supporter in N₂ atmosphere, and were characterized by XRD, XPS, UV-Vis diffuse reflection and zeta-potential. Their photocatalytic activities were evaluated using reactive brilliant red K-2G (K-2G) and cationic blue X-GRL (CBX) showing different adsorption behavior on the oxides. Fe, Cu supported TiO₂/SiO₂ can efficiently extend the light absorption to the visible region. XPS analysis verified that the introduction of transition metal lead to the changes of the electronic environmental of Ti cations and the zeta-potential of oxides. As a result, K-2G has higher adsorption on the modified TiO₂/SiO₂ than that on the baked one, while the adsorption of CBX has a little change on the both oxides. At the same time, for the photodegradation of K-2G, Fe³⁺, Co²⁺, Ni²⁺-modified catalysts show that their photoactivities are 3.3–2.2 times higher than the bare one. On the contrast, all transition-metal-supported catalysts have no significant activity improvement except that Fe/TiO₂/SiO₂ shows 1.68 times higher activity for the photodegradation of CBX. The results indicate that the photoactivity could be increased in photodegradation of dyes by changing the performances of adsorption to dyes and absorption to light of photocatalyst.