The effects of gate length variation and trapping effects on the transient response of AlGaN/GaN HEMT’s on SiC substrates

In AlGaN/GaN heterostructure field-effect transistors, the surface defects and dislocations may serve as trapping centers and affect the device performance via leakage current. In this paper we report results of our investigation of the trapping characteristics of Al_0.25Ga_0.75N/GaN HEMT using the Conductance Deep Level Transient Spectroscopy (CDLTS). Two deep level electronic defects were observed labeled E₁ and HL₁, with activation energies E_a1 = 1.36 eV and E_a2 = 0.63 eV. The hole-trap HL₁ is characterized for the first time in our studies. We identified the characteristics of the traps at the AlGaN/GaN interface adjoining the channel and the surface along the ungated region between the gate and the drain, as well as the effects of the surface traps.     

Comparative study of AlGaN/GaN metal-oxide-semiconductor heterostructure field-effect transistors with Al2O3 and HfO2 gate oxide

AlGaN/GaN metal-oxide-semiconductor heterostructure field-effect transistors (MOSHFETs) with Al₂O₃ gate oxide which was deposited by atomic layer deposition (ALD) were fabricated and their performance was then compared with that of AlGaN/GaN MOSHFETs with HfO₂ gate oxide. The capacitance (C)-voltage (V) curve of the Al₂O₃/GaN MOS diodes showed a lower hysteresis and lower interface state density than the C-V curve of the HfO₂/GaN diodes, indicating better quality of the Al₂O₃/GaN interface. The saturation of drain current in the I_D-V_GS relation of the Al₂O₃ AlGaN/GaN MOSHFETs was not as pronounced as that of the HfO₂ AlGaN/GaN MOSHFETs. The gate leakage current of the Al₂O₃ MOSHFET was five to eight orders of magnitude smaller than that of the HfO₂ MOSHFETs.     

AlGaN/GaN Recessed MIS-Gate HFET With High-Threshold-Voltage Normally-Off Operation for Power Electronics Applications

This letter reports normally-off operation of an AlGaN/GaN recessed MIS-gate heterostructure field-effect transistor with a high threshold voltage. The GaN-based recessed MIS-gate structure in conjunction with negative polarization charges under the gate allows us to achieve the high threshold voltage, whereas the low on-state resistance is maintained by the 2-D electron gas remaining in the channel except for the recessed MIS-gate region. The fabricated device exhibits a threshold voltage as high as 5.2 V with a maximum field-effect mobility of 120 $hbox{cm}^{2}/hbox{V}cdot hbox{s}$, a maximum drain current of over 200 mA/mm, and a breakdown voltage of 400 V.      

边欧姆工艺对AlN/GaN 异质结场效应晶体管极化梯度库仑场散射的影响

Using the measured capacitance–voltage and current–voltage characteristics of the rectangular Al N/Ga N heterostructure field-effect transistors(HFETs) with the side-Ohmic contacts, it was found that the polarization Coulomb field scattering in the Al N/Ga N HFETs was greatly weakened after the side-Ohmic contact processing, however, it still could not be ignored. It was also found that, with side-Ohmic contacts, the polarization Coulomb field scattering was much stronger in Al N/Ga N HFETs than in Al Ga N/Al N/Ga N and In0:17Al0:83N/Al N/Ga N HFETs, which was attributed to the extremely thinner barrier layer and the stronger polarization of the Al N/Ga N heterostructure.     

Effect of Annealing on the Characteristics of Pd/Au Contacts to p-Type GaN/Al0.45Ga0.55N

The effect of annealing on the characteristics of Pd/Au contacts to p-type GaN/Al_0.45Ga_0.55N was investigated. The electrical characteristics of Pd/Au contacts and a p-GaN/AlGaN sample were measured after annealing at different temperatures from 550°C to 850°C. Changes in the surface electrical characteristic of p-GaN/AlGaN material were observed after each annealing step. It is indicated that the surface electrical characteristic of p-GaN/AlGaN material plays an important role in the current transport through Pd/Au pads. A possible reason for those changes is impurity contamination, most likely oxygen and carbon contamination introduced from processing. The microstructure of Pd on p-GaN/AlGaN was investigated by glancing-incidence x-ray diffraction (GXRD). The results of GXRD show that the AlPd₂ and GaPd₂ phases were formed at the interface after annealing, and the formation of these phases could be effective for forming ohmic contacts on p-GaN/AlGaN.     

Specific features of kinetics of molecular beam epitaxy of compounds in the GaN-AlN system

The effect of growth conditions (V/III ratio, substrate temperature) on the properties of materials in AlN-GaN systems is discussed. A concept of the growth of the AlN/AlGaN/GaN multilayer heterostructure, which provides the improvement of crystal quality and surface morphology of the layers, is suggested and realized. The improvement of the properties of GaN in the AlN/AlGaN/GaN/AlGaN multilayer heterostructure is confirmed by a considerable increase in electron mobility in the two-dimensional electron gas formed at the upper heterointerface GaN/Al_0.3Ga_0.7N.     

Comparative study of AlGaN/GaN HEMTs robustness versus buffer design variations by applying Electroluminescence and electrical measurements

By means of step stressing tests on AlGaN/GaN HEMTs the robustness properties of devices fabricated on wafers with different buffer designs have been compared to each other (standard UID GaN buffer and UID Al_0.05Ga_0.95N back-barrier in combination with GaN channel layer). The devices with GaN buffer showed an abrupt increase of gate leakage current after reaching drain bias values in the range of 30 V while devices with Al_0.05Ga_0.95N back-barrier did not show any degradation up to 120 V drain bias. All DC-Step-Stress tests have been accompanied by Electroluminescence (EL) analysis and electrical characterization techniques before, during and after stress. It has been shown that EL at forward and reverse bias conditions can be used as an indicator of potential device degradation. Devices comprising an AlGaN back-barrier design demonstrated superior robustness.     

等离子体刻蚀凹栅槽影响AlGaN/GaN HEMT栅电流的机理

对等离子体干法刻蚀形成的凹栅槽结构AlGaN/GaN HEMTs肖特基电流增加的机理进行了研究.实验表明,凹栅槽结构AIGaN/GaN HEMTs肖特基栅电流增加一个数量级以上,击穿电压有一定程度的下降.利用AFM和XPS的方法分析AlGaN表面,等离子体干法刻蚀增加了AlGaN表面粗糙度,甚至出现部分尖峰状突起,增大了栅金属与AlGaN的接触面积;另一方面,等离子体轰击使AlGaN表面出现一定量的N空位,相当于栅金属与AlGaN接触界面处出现n型掺杂层,使肖特基结的隧道效应加强,降低了肖特基势垒.由此表明,AlGaN表面粗糙度的增加以及一定量的N空位出现是引起栅电流急剧增大的根本原因.     

Design and optimization of high voltage LDMOS transistors on 0.18 μm SOI CMOS technology

In this paper, we have studied the effect of systematic downscaling of MOS channel length of the performance of the hybrid GaN MOS-HEMT with numerical simulations. The improvement in on-state conduction, together with concomitant short channel effects, including drain induced barrier lowering (DIBL) is quantitatively evaluated. A specific on-resistance of 2.1 mΩ cm² has been projected for a MOS channel length of 0.38 μm. We also have assessed the impact of high-k gate dielectrics, such as Al₂O₃. In addition, we have found that adding a thin GaN cap layer on top of AlGaN barrier can help reducing short channel effects.     

AlxGa1−xN/GaN multi-quantum-well ultraviolet detector based on p-i-n heterostructures

We report on characterization of a set of AlGaN/GaN multiple-quantum-well (MQW) photodetectors. The model structure used in the calculation is the p-i-n heterojunction with 20 AlGaN/GaN MQW structures in i-region. The MQW structures have 2 nm GaN quantum well width and 15 nm Al_xGa_1−xN barrier width. The cutoff wavelength of the MQW photodetectors can be tuned by adjusting the well width and barrier height. Including the polarization field effects, on increasing Al mole fraction, the transition energy decreases, the total noise increases, and the responsivity has a red shift, and so the detectivity decreases and has a red shift.     

SiO/sub 2//AlGaN/InGaN/GaN MOSDHFETs

The characteristics of a novel nitride based field-effect transistor combining SiO/sub 2/ gate isolation and an AlGaN/InGaN/GaN double heterostructure design (MOSDHFET) are reported. The double heterostructure design with InGaN channel layer significantly improves confinement of the two-dimensional (2-D) electron gas and compensates strain modulation in AlGaN barrier resulting from the gate voltage modulations. These decrease the total trapped charge and hence the current collapse. The combination of the SiO/sub 2/ gate isolation and improved carrier confinement/strain management results in current collapse free MOSDHFET devices with gate leakage currents about four orders of magnitude lower than those of conventional Schottky gate HFETs.     

AlGaN/GaN MIS-HFETs with f/sub T/ of 163 GHz using cat-CVD SiN gate-insulating and passivation Layers

Al/sub 0.4/Ga/sub 0.6/N/GaN heterostructure field-effect transistors (HFETs) with an AlGaN barrier thickness of 8 nm and a gate length (L/sub G/) of 0.06-0.2 /spl mu/m were fabricated on a sapphire substrate. We employed two novel techniques, which were thin, high-Al-composition AlGaN barrier layers and SiN gate-insulating, passivation layers formed by catalytic chemical vapor deposition, to enhance high-frequency device characteristics by suppressing the short channel effect. The HFETs with L/sub G/=0.06-0.2 /spl mu/m had a maximum drain current density of 1.17-1.24 A/mm at a gate bias of +1.0 V and a peak extrinsic transconductance of 305-417 mS/mm. The current-gain cutoff frequency (f/sub T/) was 163 GHz, which is the highest value to have been reported for GaN HFETs. The maximum oscillation frequency (f/sub max/) was also high, and its value derived from the maximum stable gain or unilateral gain was 192 or 163 GHz, respectively.     

Thermal stability investigations of AlGaN/GaN HEMTs with various high work function gate metal designs

The operation of high power RF transistor generates a huge amount of heat and thermal effect is a major consideration for improving the efficiency of power transistors. AlGaN/GaN high electron mobility transistors (HEMTs) on silicon substrates have been studied extensively because of their high thermal conductivity. This study comprehensively investigates the DC, low frequency noise, microwave and RF power performance of Al_0.27Ga_0.73N/GaN HEMTs on silicon substrates at temperatures from room temperature to 100 °C using high work function metals such as palladium (Pd) and iridium (Ir) gate metals. Although the conventional Ni gate exhibited a good metal work function with AlGaN, which is beneficial for increasing the Schottky barrier height of HEMTs, the diffusion of Ni metal toward the AlGaN and GaN layers influences the DC and RF stability of the device at high temperatures or over long-term operation. Pd and Ir exhibited less diffusion at high temperature than Ni, resulting in less degradation of device characteristics after high temperature operation.     

Local electronic properties of AlGaN/GaN heterostructures probed by scanning capacitance microscopy

Local electronic properties in Al_xGa_1−xN/GaN heterostructure field-effect transistor epitaxial layer structures are probed using scanning capacitance microscopy. Acquisition of scanning capacitance images over a wide range of bias voltages combined with theoretical analysis and numerical simulation allows the presence, detailed nature, and possible structural origins of nanometer- to micronscale inhomogeneities in electronic structure to be elucidated. Substantial lateral variations in local threshold voltages for transistor channel formation are observed, at length scales ranging from submicron to >2 μm, and found to arise primarily from local variations in Al_xGa_1−xN layer thickness. Features in electronic structure are also observed that are consistent with the existence of networks of negatively charged threading edge dislocations, as might be formed at island coalescence boundaries during epitaxial growth. The negative charge associated with these structures appears to lead to local depletion of carriers from the channel in the Al_xGa_1−xN/GaN transistor epitaxial layer structure.     

The effect of built-in electric field in GaN/AlGaN quantum wells with high AIN mole fraction

Spontaneous and piezoelectric polarization in hexagonal GaN/AlGaN heterostructures give rise to large built-in electric fields. The effect of the builtin electric field in GaN/Al_xGa_1−xN quantum wells was investigated for x=0.2 to 0.8 by photoluminescence studies. The quantum well structures were grown by molecular beam epitaxy on (0001) sapphire substrates. Cross-sectional transmission electron microscopy performed on the samples revealed abrupt interfaces and uniform layer thicknesses. The low temperature (4 K) photoluminescence peaks were progressively red-shifted due to the quantum confined Stark effect depending on the AlN mole fraction in the barriers and the thickness of the GaN quantum well. Our results verify the existence of very large built-in electric fields of up to 5 MV/cm in GaN/Al_0.8Ga_0.2N quantum wells.     

AlGaN/GaN metal-oxide semiconductor heterostructure field-effect transistor with photo-chemical-vapor deposition SiO<Subscript>2</Subscript> gate oxide

High-quality SiO₂ was successfully deposited onto GaN by photo-chemicalvapor deposition (photo-CVD) using a D₂ lamp as the excitation source. The AlGaN/GaN metal-oxide semiconductor, heterostructure field-effect transistors (MOSHFETs) were also fabricated with photo-CVD oxide as the insulating layer. Compared with AlGaN/GaN metal-semiconductor HFETs (MESHFETs) with similar structure, we found that we could reduce the gate-leakage current by more than four orders of magnitude by inserting the photo-CVD oxide layer in between the AlGaN/GaN and the gate metal. With a 2-μm gate, it was found that the saturated I_ds, maximum g_m, and gate-voltage swing (GVS) of the fabricated nitride-based MOSHFET were 512 mA/mm, 90.7 mS/mm, and 6 V, respectively.     

Selective dry etching of (Sc2O3)x(Ga2O3)1−x gate dielectrics and surface passivation films on GaN

(Sc₂O₃)_x(Ga₂O₃)_1?x films grown by molecular beam epitaxy show promise for use as surface passivation layers and gate dielectrics on GaN-based high electron mobility transistors. Completely selective, low-damage, dry etching of (Sc₂O₃)_x(Ga₂O₃)_1?x films with respect to GaN can be achieved with low-power inductively coupled plasmas of CH₄/H₂/Ar with etch rates in the range 200–300 Å/min. The incident ion energies are of order 100 eV, and no roughening of the underlying GaN was observed under these conditions. Similar etch rates were obtained with Cl₂/Ar discharges under the same conditions, but GaN showed rates almost an order of magnitude higher.     

High field-effect mobility normally-off AlGaN/GaN hybrid MOS-HFET on Si substrate by selective area growth technique

The paper reports a normally-off n-channel AlGaN/GaN hybrid metal-oxide-semiconductor heterojunction field-effect transistor (MOS-HFET) on Si substrate with high field-effect mobility. To decrease the channel resistance and to improve the field-effect mobility, of the MOS-HFET, a selective area growth (SAG) technique is applied at the channel region. The fabricated MOS-HFET exhibits a good normally-off operation with the threshold voltage of 3.7 V, the specific ON-state resistance of 7.6 mΩ cm², and the breakdown voltage of over 800 V.     

Design and Growth of Visible-Blind and Solar-Blind III-N APDs on Sapphire Substrates

GaN-based visible-blind and AlGaN-based solar-blind avalanche photodiodes (APDs) have been grown and fabricated on sapphire substrates. The GaN p-i-n APDs show low dark current with high gain. The AlGaN layers for the Al_0.55Ga_0.45N-based APDs are grown using a newly developed pulsed metalorganic chemical vapor deposition (MOCVD) process, and the material characterization results show excellent material quality. The spectral responsivity of the devices show a bandpass characteristic with cutoffs in the ultraviolet (UV) visible-blind and solar-blind spectrum for GaN- and Al_0.55Ga_0.45N-based APDs, respectively.     

Comparative studies of normally-off Al0.26Ga0.74N/AlN/GaN/Si high electron mobility transistors with different gate structures

Systematic designs to achieve normally-off operation and improved device performance for Al_0.26Ga_0.74N/AlN/GaN high electron mobility transistors (HEMTs) grown on a Si substrate are investigated in this work. The step-by-step approach includes: (1) devising a thin AlGaN/AlN composite barrier, (2) introducing fluoride ions within the active region by using CF₄ plasma treatment, (3) growing the Al₂O₃ oxide passivation layers within gate-drain/source regions by using a cost-effective ozone water oxidization technique, and (4) integrating a metal-oxide-semiconductor gate (MOS-gate) design with high-k Al₂O₃ gate dielectric. Devices with four different evolutionary gate structures have been compared and studied. Variations of threshold voltage (V_th), Hooge coefficients (α_H), maximum drain-source current density (I_{DS, max}), maximum extrinsic transconductance (g_{m, max}), gate-voltage swing (GVS) linearity, two-terminal gate-drain breakdown/turn-on voltages (BV_GD/V_on), on/off current ratio (I_on/I_off), and high-temperature characteristics up to 450 K are also investigated.