负载型Pd/SBA—15催化剂催化性能研究

将负载型催化剂Pd/SBA—15用于催化邻氯硝基苯加氢。考察了反应温度、催化剂用量对Pd/SBA—15催化性能的影响,并考察了催化剂的使用寿命。实验结果表明,Pd/SBA—15催化剂表现出很好的催化性能,有望应用于工业生产。     

选择性催化加氢合成3,4-二氯苯胺的Pd/C催化剂研究

研究了Pd/C催化剂表面金属钯平均粒径对3,4-二氯硝基苯催化加氢反应选择性的影响，发现金属钯平均粒径越大，脱氯副反应越不明显，加氢选择性越高。采用浓硝酸预处理的活性炭负载钯催化剂虽然能够增大表面金属钯平均粒径，粒径分布却较宽，不利于加氢选择性的提高。使用饱和EDTA·2Na溶液预处理活性炭后，在钯负载量降低的情况下，可以达到活性炭载体表面金属钯大粒径、狭窄的分布，实现了在不添加脱氯抑制剂的情况下高选择性合成3,4-二氯苯胺。     

Liquid phase hydrodechlorination of chlorophenols over Pd/C and Pd/Al2O3: a consideration of HCl/catalyst interactions and solution pH effects

The liquid phase hydrodechlorination (HDC) of 2-chlorophenol (2-CP) and 2,4-dichlorophenol (2,4-DCP) has been studied over 1% (w/w) Pd/C and Pd/Al₂O₃ under conditions of minimal mass transport constraints. The HDC of 2,4-DCP generated HCl and 2-CP as the only intermediate partially dechlorinated product which reacts further to yield phenol; cyclohexanone was formed over Pd/Al₂O₃, but not over Pd/C, prior to complete dechlorination. Pd/Al₂O₃ is characterized (on the basis of TEM analysis) by a narrow distribution of smaller Pd particles to give a surface area weighted mean particle DIAMETER = 2.4 nm that is appreciably lower than the value of 13.2 nm established for Pd/C, where the latter is characterized by a broader distribution of larger (spherical) particles. The addition of NaOH served to increase fractional dechlorination by suppressing HDC inhibition due to the HCl that is generated. Reuse of the catalysts revealed an appreciable deactivation of Pd/C and a limited loss of activity in the case of Pd/Al₂O₃. Deactivation of Pd/C can be linked to a decrease (up to ca. 60%) in the initial BET surface area allied to appreciable leaching (up to ca. 40%) of the starting Pd content through the corrosive action of HCl and, while the average Pd diameter is essentially unaffected, there is evidence of a preferred leaching of larger Pd particles. The stronger metal/support interactions prevalent in Pd/Al₂O₃ results in limited Pd leaching and comparable initial HDC activities during catalyst reuse with/without NaOH addition. Inclusion of HCl in the reaction mixture (pH 5–1.5) resulted in a marked decline in the initial HDC rate associated with Pd/Al₂O₃ and a lesser drop in HDC activity for Pd/C. The difference in response to bulk solution pH variations are discussed in terms of the nature of the reactive species in solution and the amphoteric behavior of the Pd supports.     

载体预处理对Pd/C催化剂催化性能的影响

研究了活性炭硝酸表面改性对以其为载体制备的负载钯催化剂性能的影响。利用表面官能团滴定、N₂物理吸附和扫描电镜对催化剂进行表征，以邻硝基氯苯催化加氢制备2，2'-二氯氢化偶氮苯反应为模型反应对催化剂的性能进行评价。结果表明，经过不同浓度的HNO₃处理，活性炭孔结构性能变化不大，但是活性炭表面酸性含氧基团的浓度有了较大程度的增长，为Pd金属粒子的沉积提供了大量的吸附位，提高了Pd金属的分散度，从而制得高活性的Pd/C催化剂。通过30%HNO₃ 60 ℃水浴中回流4 h处理的活性炭可以达到最佳效果，所制得催化剂的活性是以未经硝酸处理过的活性炭载体制备的催化剂活性的2.3倍。     

硫化物对裂解汽油一段加氢用Pd/Al_2O_3催化剂性能的影响

采用固定床反应器考察了多种硫化物(二硫化碳、二甲基二硫与噻吩)对裂解汽油一段加氢用Pd/Al2O3催化剂加氢性能的影响。在相同的工艺条件下,硫化物的毒性顺序为:二硫化碳二甲基二硫噻吩。CS2对催化剂加氢性能的影响最为明显,原料油中CS2质量分数达到6μg/g后,催化剂就迅速发生中毒,产品双烯值增高。催化剂失活的原因是CS2主要以物理吸附的方式占据催化加氢活性中心,导致催化剂对共轭烯烃与氢气失去吸附活性。     

助剂对碳四馏分选择性加氢Pd/Al2O3催化剂性能的影响

以Al₂O₃为载体,Pd为活性组分,Ag和Li为助剂,制备碳四馏分选择性加氢脱除丁二烯催化剂,并对催化剂进行XPS、TPR和TPD表征。结果表明,加入助剂Ag使Pd的电子云密度升高,而加入助剂Li使催化剂表面酸中心数量减少。催化剂评价结果表明,加入助剂Ag和Li后,催化剂的1-丁烯双键异构活性降低,加氢选择性提高。     

Mechanistic investigation of the hydrodechlorination of 1,1,1,2-tetrafluorodichloroethane on metal fluoride-supported Pt and Pd

The hydrodechlorination of CF₃CCl₂F over Pd and Pt supported on β-AlF₃ and MgF₂ with D₂ gas has been investigated employing temperature programmed isotope exchange (TPIE) under static conditions. The isotope exchange observed between the H-loaded metal catalyst and the D₂ gas phase demonstrates the significantly higher hydrogen uptake capability of Pd-based catalysts. Both Pd and Pt on β-AlF₃, show significantly higher hydrogen/deuterium uptake and isotope exchange activity as compared with the MgF₂ support, probably due to the presence of hexagonal channels in β-AlF₃ and its higher Lewis acidity. The combination of these properties make Pd/β-AlF₃ a superior catalyst for selective hydrodechlorination of CF₃CCl₂F. Based on the results of the hydrodechlorination of CF₃CCl₂F with D₂, a competitive rather than a consecutive mechanism is proposed. The data from H/D-TPIE are best interpreted by the formation of surface carbene species as intermediates.     

Pd(OAc)_2/P(t-Bu)_3催化合成空穴传输材料APB的研究

以二苯基联苯二胺(DPB)和9-溴蒽为原料,在叔丁醇钠强碱环境下,以Pd(OAc)2/P(t-Bu)3为催化剂合成了新型空穴传输材料N,N’-二苯基-N,N’-二蒽基-1,1’-联苯-4,4’-二胺(APB)。得到优化的催化反应条件为:以二甲苯为溶剂在130~138℃回流反应3 h,Pd(OAc)2∶P(t-Bu)3=1∶1.2(摩尔比),P(t-Bu)3/9-溴蒽=0.24%;经元素分析、GC-MS、1H NMR等表征了结构;差示扫描量热仪(DSC)分析结果显示其熔点为324℃,具有良好的热稳定性。     

On the promotional effect of Pd on the propene-assisted decomposition of NO on chlorinated Ce0.68Zr0.32O2

The selective catalytic reduction (SCR) of NO_x assisted by propene is investigated on Pd/Ce_0.68Zr_0.32O₂ catalysts (Pd/CZ), and is compared, under identical experimental conditions, with that found on a Pd/SiO₂ reference catalyst. Physico-chemical characterisation of the studied catalysts along with their catalytic properties indicate that Pd is not fully reduced to metallic Pd for the Pd/CZ catalysts. This study shows that the incorporation of Pd to CZ greatly promotes the reduction of NO in the presence of C₃H₆. These catalysts display very stable deNO_x activity even in the presence of 1.7% water, the addition of which induces a reversible deactivation of about 10%. The much higher N₂ selectivity obtained on Pd/CZ suggests that the lean deNO_x mechanism occurring on these catalysts is different from that occurring on Pd⁰/SiO₂. A detailed mechanism is proposed for which CZ achieves both NO oxidation to NO₂ and NO decomposition to N₂, whereas PdO_x activates C₃H₆ via ad-NO₂ species, intermediately producing R-NO_x compounds that further decompose to NO and C_xH_yO_z. The role of the latter oxygenates is to reduce CZ to provide the catalytic sites responsible for NO decomposition. The proposed C₃H₆-assisted NO decomposition mechanism stresses the key role of NO₂, R-NO_x and C_xH_yO_z as intermediates of the SCR of NO_x by hydrocarbons.     

Pd/Na2O/K2O/γ-Al2O3三元催化活性分析与评价

本文以浸渍法制备了活性γ-Al₂O₃涂层及Pd/Na₂O/K₂O/γ-Al₂O₃三元催化剂。考察了γ-Al₂O₃涂层比表面积随高温老化时间变化的规律。在实验室模拟尾气配气系统上，对Pd/Na₂O/K₂O/γ-Al₂O₃三元催化剂的起燃温度、抗高温老化及抗SO₂中毒能力进行了分析与评价。本文的γ-Al2O3涂层能经受1050℃的高温老化。Pd/Na₂O/K₂O/γ-Al₂O₃三元催化剂经900℃高温老化两次共13h后，其最大催化活性几乎不变，其老化样经600℃硫中毒1h后对CO和HC的催化转化率仍在75％以上。Pd/Na₂O/K₂O/γ-Al₂O₃新鲜样的起燃温度为280℃，二次老化样的起燃温度为320～350℃，具有很高三元催化活性。     

Wet oxidation of bleach plant effluent: Effects of pH on the oxidation with or without a Pd/Al2O3 catalyst

Wet oxidation of acidic bleach plant effluent was carried out at 423K and 1.5 MPa in a slurry reactor. The influence of pH of the bleach plant effluent was evaluated for both catalytic and non-catalytic oxidation in the liquid phase. The stability of the heterogeneous catalysts was investigated by measuring the extent of metal leaching into the solution. The pH of wastewater solution was found to influence significantly both the rate of total organic carbon (TOC) removal and the stability of the Pd/Al₂O₃ catalyst. Leaching of palladium and alumina occurred mostly at pH 2 and pH 11 under experimental conditions. With Pd/Al₂O₃, comparable rates of TOC removal were obtained in the pH range of 5 to 9 without significant leaching of both palladium and alumina. No metal leaching was observed using the Pd-Pt/Al₂O₃ catalyst at an initial pH value of 7. Implications of these experimental results for designing a catalytic wet oxidation process are discussed. A novel approach has been proposed for the treatment of effluents from softwood Kraft pulp mills.     

Pd/Pt on Ti-containing Mixed Oxides as Dearomatization Catalysts: Physico-chemical Characterization and Activity

Pd/Pt supported on pure and doped TiO₂ (TiO₂–WO₃ and TiO₂–WO₃–SiO₂) were prepared and characterized by different techniques (XPS, TEM, XRD, H₂-TPR and TPD of ammonia). These catalysts were investigated in the hydrogenation of tetralin at 6.0 MPa, checking also their thio-tolerance by feeding increasing amounts of dibenzothiophene (DBT, 300 and 1000 wt ppm). The catalytic activity followed the order: Pd/Pt–TiO₂ > Pd/Pt–TiO₂–WO₃–SiO₂ > Pd/Pt–TiO₂–WO₃, evidencing a negative role of a second oxide inside TiO₂. The Pd/Pt–TiO₂ catalyst showed high activity regardless of reaction conditions (temperature, contact time, H₂/tetralin ratio) together with a good thio-tolerance up to 300 wt ppm of DBT.     

Combined CO/CH4 oxidation tests over Pd/Co3O4 monolithic catalyst: Effects of high reaction temperature and SO2 exposure on the deactivation process

CO and CH₄ combined oxidation tests were performed over a Pd (70 g/ft³)/Co₃O₄ monolithic catalyst in conditions of GHSV = 100,000 h⁻¹ and feed composition close to that of emission from bi-fuel vehicles. The effect of SO₂ (5 ppm) on CO and CH₄ oxidation activity under lean condition (λ = 2) was investigated. The presence of sulphur strongly deactivated the catalyst towards methane oxidation, while the poisoning effect was less drastic in the oxidation of CO. Saturation of the Pd/Co₃O₄ catalytic sites via chemisorbed SO₃ and/or sulphates occurred upon exposure to SO₂. A treatment of regeneration to remove sulphate species was attempted by performing a heating/cooling cycle up to 900 °C in oxidizing atmosphere. Decomposition of PdO and Co₃O₄ phases at high temperature, above 750 °C, was observed. Moreover, sintering of Pd⁰ and PdO particles along with of CoO crystallites takes place.     

Influence of the oxygen pretreatment on the CO2 reforming of methane on Ni/β-SiC catalyst

The influence of the O₂ pretreatment on the CO₂ reforming of methane to synthesis gas has been investigated with Ni catalysts supported on β-SiC extrudate. The structure and properties of the catalysts were characterised by SEM, TEM and XRD techniques. The pretreatment of the catalyst by a mixture of CO₂ and O₂ significantly improves the catalytic activity for the CO₂ reforming. On the Ni 5 wt.% supported on β-SiC catalyst, the CH₄ conversion has reached 90% with the O₂ pretreatment instead of 80% by direct activation under CO₂/CH₄ mixture. The oxygen pretreatment seems to stabilize the metallic nickel phase instead of NiSi₂.     

Partial oxidation of methane over Ni/Ce-Zro<Subscript>2</Subscript>/θ-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>

The catalytic behavior of Ni/Ce-ZrO₂/θ-Al₂O₃ has been investigated in the partial oxidation of methane (POM) toward synthesis gas. The catalyst showed high activity and selectivity due to the heat treatment of the support and the promotional effect of Ce-ZrO₂. It is suggested that the support was stabilized through the heat treatment of γ-Al₂O₃ and the precoating of Ce-ZrO₂, on which a protective layer was formed. Moreover, sintering of the catalyst was greatly suppressed for 24 h test. Pulse experiments of CH₄, O₂ and/or CH₄/O₂ with a molar ratio of 2 were systematically performed over fresh, partially reduced and well reduced catalyst. Results indicate that CH₄ can be partially oxidized to CO and H₂ by the reactive oxygen in complex NiO_x species existing over the fresh catalyst. It is demonstrated that POM over Ni/Ce-ZrO₂/θ-Al₂O₃ follows the pyrolysis mechanism, and both the carbonaceous materials from CH₄ decomposition over metallic nickel and the reactive oxygen species present on NiO_x and Ce-ZrO₂ are intermediates for POM.     

FT-IR spectroscopic investigation of the surface reaction of CH4 with NO x species adsorbed on Pd/WO3–ZrO2 catalyst

The interaction of methane at various temperatures with NO _x species formed by room temperature adsorption of NO + O₂ mixture on tungstated zirconia (18.6 wt.% WO₃) and palladium(II)-promoted tungstated zirconia (0.1 wt.% Pd) has been investigated using in situ FT-IR spectroscopy. A mechanism for the reduction of NO over the Pd-promoted tungstated zirconia is proposed, which involves a step consisting of thermal decomposition of the nitromethane to adsorbed NO and formates through the intermediacy of cis-methyl nitrite. The HCOO⁻ formed acts as a reductant of the adsorbed NO producing nitrogen.     

Promoting effect of propane traces on the activity of Pt/γ-Al2O3 and Pt–Sn/γ–Al2O3 catalysts in CH4–SO2–O2 reactions

A strong promoting effect of the presence of C₃H₈ or C₃H₆ was determined for the CH₄–SO₂–O₂ reaction, over pre-sulfated 1%Pt/γ–Al₂O₃ and pre-sulfated 1%Pt–2%Sn/γ–Al₂O₃ catalysts. These results suggest that over 1%Pt–2%Sn/γ–Al₂O₃ catalysts, small amounts of propane or propylene in the gas feed may eliminate methane emissions at low temperatures from lean-burn NGV exhausts.     

A comparative study of the thermal stability and reactions of CH2, CH3 and C2H5 species on the Pd(100) surface

Adsorbed CH₂, CH₂ and C₂H₅ moieties were produced on Pd(100) at 90 K by photoinduced dissociation of the corresponding iodo compounds, and their thermal reactions were established.This laboratory is a part of the Center of Catalysis, Surface and Material Science at the University of Szeged.