Simultaneous determination of five tobacco-specific nitrosamines in mainstream cigarette smoke by isotope dilution liquid chromatography/electrospray ionization tandem mass spectrometry

Tobacco-specific nitrosamines (TSNAs) have been previously implicated as a source of carcinogenicity in tobacco and cigarette smoke. Accurate quantification of these chemicals is needed to help assess public health risk. We have developed and validated a specific and sensitive method to simultaneously measure five TSNAs in the particulate phase of mainstream tobacco smoke. Cigarette smoke particulate, produced using standardized machine smoking protocols, was collected on a Cambridge filter pad. The particulate matter was extracted using methylene chloride, back extracted into aqueous solution, further purified by solid-phase extraction, and analyzed by liquid chromatography/electrospray ionization tandem mass spectrometry using isotopically labeled analogues as internal standards. Limits of detection for this method ranged from 0.05 to 1.23 ng/mL using an injection volume of 20 microL. A linear calibration range spanning 2.5-2500 ng/mL was adequate to measure TSNA levels in cigarette smoke. The method achieved excellent reproducibility and accuracy. The identity of each TSNA was established by chromatographic retention time, analyte-specific fragmentation patterns, and relative peak area ratios of two product/precursor ion pairs. This new method provides higher sensitivity, specificity, and throughput than earlier methods for TSNA determination.     

Quantitative method for the analysis of tobacco-specific nitrosamines in cigarette tobacco and mainstream cigarette smoke by use of isotope dilution liquid chromatography tandem mass spectrometry

An improved liquid chromatography tandem mass spectrometry (LC-MS/MS) method has been developed for the determination of tobacco specific nitrosamines (TSNA). It utilizes four stable isotope-labeled internal standards instead of two as reported by others. A separate internal standard for each analyte is required to minimize sample matrix effects on each analyte, which can lead to poor analyte recoveries and decreases in method accuracy and precision if only one or two of the internal standards are used, especially for complex sample matrixes and when no sample cleanup steps are performed as in this study. In addition, two ion-transition pairs (instead of one) are used for each analyte for the confirmation and quantification, further enhancing the method's accuracy and robustness. These improvements have led to a new LC-MS/MS method that is faster, more sensitive, and selective than the traditional methods and more accurate and robust than the published LC-MS/MS methods. The linear range of the method was from 0.2 to 250 ng/mL with a limit of detection of each TSNA varied from 0.027 to 0.049 ng/mL. Good correlations between the results obtained by the new method and the traditional method were observed for the samples studied.     

The detection of nitro pesticides in mainstream and sidestream cigarette smoke using electron monochromator-mass spectrometry

Over the past decade, electron monochromator-mass spectrometry (EM-MS) has been shown to be a selective and sensitive technique for the analysis of a wide variety of electrophilic compounds in complex matrixes. Here, for the first time, three different dinitroaniline pesticides, flumetralin, pendimethalin, and trifluralin, have been shown to be present in both mainstream and sidestream tobacco smoke using an EM-MS system. A number of cigarettes were tested that included three pure-tobacco-type cigarettes, an experimental reference cigarette, and 11 commercial cigarettes. Due to the complexity of the smoke particulate matter, the pesticides were identified only after each sample was subjected to a multistep cleanup process that included phenyl solid-phase extraction; an acid wash; aminopropyl solid-phase extraction; and finally, normal phase LC fractionation. All cigarette types tested showed the presence of the three pesticides in the tobacco smoke, with flumetralin ranging from trace levels up to 37 (+/- 9) ng/cig, pendimethalin ranging from trace levels up to 10.4 (+/- 0.6) ng/cig, and trifluralin ranging from trace levels up to 47 (+/- 17) ng/cig. Acute toxicity information is presented for the three pesticides.     

Automated in-tube solid-phase microextraction coupled with HPLC for the determination of N-nitrosamines in cell cultures

An automated in-tube solid-phase microextraction (SPME) HPLC analysis method for 4-(methylnitrosamino)-1-(3-pyridyl)-1-butanone (NNK) and several metabolites has been developed. NNK is one of the tobacco-specific N-nitrosamines (TSNA), which has been linked to cancers associated with the use of or exposure to tobacco products. In-tube SPME is an on-line extraction technique in which analytes are extracted and concentrated from the sample directly into a coated capillary by repeated draw/eject steps. In this study, a tailor-made polypyrrole (PPY)-coated capillary and several commercially available capillaries (capillary GC columns) were used to evaluate their extraction efficiencies for NNK and several metabolites in cell cultures. Compared with commercial capillaries that were currently used for in-tube SPME, the PPY-coated capillary showed better extraction efficiency for all of the compounds studied. After optimization of the extraction conditions, NNK and five metabolite compounds were analyzed in spiked cell cultures, confirming the applicability of the developed method. Excellent linearity was observed for all compounds (av R2 = 0.9942) and detection limits that ranged from 20 to 250 ng/mL. The average within-day and between day variations (% RSD) were 2.9 and 3.6%, respectively. This automated extraction and analysis method simplified the determination of the TSNA, requiring a total sample analysis time of only approximately 30 min.     

Determination of lead in environmental waters with dispersive liquid-liquid microextraction prior to atomic fluorescence spectrometry

This paper established a new, rapid and sensitive method for the determination of lead in water samples preconcentrated by dispersive liquid-liquid microextraction (DLLME) prior to atomic fluorescence spectrometry. Dithizone was used as the chelating agent. In the DLLME procedure, lead formed lead-dithizone complex and migrated into the carbon tetrachloride micro-droplets. Important factors that would affect the extraction efficiency had been investigated including the kind and volume of extraction solvent and dispersive solvent, sample pH, the amount of chelating agent, extraction time and centrifugation time. The results showed that the coexisting ions containing in water samples had no obvious negative effect on the determination of lead. The experimental results indicated that the proposed method had a good linear range of 0.01-100 ng mL(-1) (r(2) = 0.9990). The precision was 2.12% (RSD, n = 7) and the detection limit was 0.95 ng L(-1). Proposed method was validated with four real environmental samples and the results indicated that the proposed method was excellent for the future use and satisfied spiked recoveries were in the range of 92.9-97.4%.     

Fluorescent approach to quantitation of reactive oxygen species in mainstream cigarette smoke

A novel approach to monitoring of mainstream smoke reactive oxygen species (ROS) has been developed and applied to the quantitation of smoke oxidants. Redox-active fluorescent probe dihydrorhodamine 6G (DHR-6G) was selected as the molecular probe because it is sensitive to typical smoke ROS. The experimental system couples an automatic cigarette smoke machine fiber-optic fluorometer for real-time monitoring of the reaction progress between cigarette smoke and DHR-6G. Quantitation was achieved based on the amount of rhodamine 6G, which is the sole product from DHR-6G oxidation. With the optimization of the trapping efficiency, we detected 391 nmol of ROS/cigarette in the mainstream CS for a standard cigarette 2R4F under standard Federal Trade Commission smoking protocol. Applying this method, we quantified the ROS of selected cigarettes and found that the cigarettes made of burley tobacco have much ( approximately 10 times) higher ROS content in the smoke than that in the tobacco made of bright tobacco. The smokeless cigarette, Eclipse, has comparable ROS with cigarettes made of bright tobacco.     

Supercritical fluid extraction and gas chromatography/mass spectrometry for the analysis of tobacco-specific nitrosamines in cigarettes

A method for measuring four tobacco-specific nitrosamines (TSNAs), an important group of compounds in tobacco products, was developed. These compounds were extracted using supercritical fluid extraction (SFE) and purified by a sodium hydroxide wash of the ethyl acetate eluting solvent and solid-phase extraction. Quantitation was performed using gas chromatography/mass spectrometry (GC/MS). Spiking experiments were carried out to determine the recovery, precision, and limits of detection of this method. The detection limits were 0.04 microgram per sample for N'-nitrosonornicotine and N'-nitrosoanatabine and 0.02 microgram for 4-(methylnitrosamino)-1-(3-pyridyl)-1-butanone and N'-nitrosoanabasine. This method was used to measure TSNAs in various brands of cigarette tobacco with excellent reproducibility. The variation of TSNA levels among the cigarettes of different packs and types was significantly smaller than that among different brands. Comparable TSNA levels were obtained with SFE and liquid extraction methods. Signal-to-noise levels were similar for GC/MS and GC/thermal energy analysis when low-level tobacco samples were analyzed.     

Selective and sensitive spectrophotometric method for determination of sub-micro-molar amounts of aluminium ion

A simple and accurate spectrophotometric method for determination of trace and ultra-trace amounts of Al3+ ion in tap and wastewater sample has been described. Using the eriochrome cyanine R (ECR) in the presence of N,N-dodecyltrimethylammonium bromide (DTAB) as cationic surfactant spectrophotometric determination of Al3+ ion has been carried out. The Beer's law is obeyed over the concentration range of 4-400 ng mL(-1) of Al3+ ion with the detection limits of 0.14 ng mL(-1), while the molar absorptivity of complexes is 1.19x10(5) L mol(-1) cm(-1). The influence of type and amount of surfactant, pH, and amount of ligand on sensitivity of spectrophotometric method were optimized. The method has been successfully applied for Al3+ ion determination in real sample.     

顶空-气相色谱法测定卷烟主流烟气粒相物中吡啶

为研究气相色谱测定卷烟主流烟气粒相物中吡啶含量,采用碳酸钠水溶液作基质校正剂,通过顶空进样、DB-WAXETR色谱柱分离、火焰离子化检测器检测。结果表明:吡啶在0.20~16.20μg/mL质量浓度范围内线性拟合度为0.9998,加标回收率在98.4%~104.7%之间,定量限为0.08μg/支,RSD小于5%,该方法可以快速、准确地测定卷烟主流烟气粒相物中吡啶。     

Selected reaction monitoring LC-MS determination of idoxifene and its pyrrolidinone metabolite in human plasma using robotic high-throughput, sequential sample injection

The generation of large numbers of samples during early drug discovery has increased the demand for rapid and selective methods of analysis. Liquid chromatography-tandem mass spectrometry (LC-MS-MS), because of its sensitivity, selectivity, and robustness, has emerged as a powerful tool in the pharmaceutical industry for many analytical needs. This work presents a high-throughput selected reaction monitoring LC-MS bioanalytical method for the determination of idoxifene, a selective estrogen receptor modulator, and its pyrrolidinone metabolite in clinical human plasma samples. The described method uses short, small-bore columns, high flow rates, and elevated HPLC column temperatures to perform LC separations of idoxifene and its metabolite within 10 s/sample. Sequential injections were accomplished with a 215/889 multiple probe liquid handler (Gilson, Inc.), which aspirates eight samples simultaneously and performs its rinse cycle parallel to sample injection, resulting in minimum lag time between injections. This high-throughput method was applied to the determination of idoxifene and its metabolite in clinical human plasma samples. Sample preparation employed liquid/liquid extraction in the 96-well format. Method validation included determination of intra- and interassay accuracy and precision values, recovery studies, autosampler stability, and freeze-thaw stability. The LOQ obtained was 10 ng/mL for idoxifene and 30 ng/mL for the metabolite. Using idoxifene-d5 as an internal standard, idoxifene showed acceptable accuracy and precision values at QC level 1 (QC1, 15 ng/mL), level 2 (QC2, 100 ng/mL), and level 3 (QC3, 180 ng/mL) (85.0% accuracy +/- 12.0% precision, 95.1 +/- 4.9%, and 90.3 +/- 4.7%, respectively). The pyrrolidinone metabolite also showed acceptable accuracy and precision values (using no internal standard for quantitation) at QC1 (60 ng/mL), QC2 (100 ng/mL), and QC3 (180 ng/mL) (104.9 +/- 14.4%, 91.1 +/- 13.0%, and 90.8 +/- 12.2%, respectively). The validated method was applied to the analysis of 613 human clinical plasma samples. An average run time of 23 s/sample (approximately 37 min/ 96-well plate or over 3,700 sample/day) was achieved. The successful validation presented indicates that rapid methods of analysis can efficiently and reliably contribute to the fast sample turnaround required for high sample number generating processes.     

Determination of trace aluminum in biological and water samples by cloud point extraction preconcentration and graphite furnace atomic absorption spectrometry detection

A cloud point extraction (CPE) method for the preconcentration of trace aluminum prior to its determination by graphite furnace atomic absorption spectrometry (GFAAS) has been developed. The CPE method is based on the complex of Al(III) with 1-phenyl-3-methyl-4-benzoyl-5-pyrazolone (PMBP), and then entrapped in non-ionic surfactant Triton X-114. PMBP was used not only as chelating reagent in CPE preconcentration, but also as chemical modifier in GFAAS determination. The main factors affecting CPE efficiency, such as pH of sample solution, concentration of PMBP and Triton X-114, equilibration temperature and time, were investigated in detail. An enrichment factor of 37 was obtained for the preconcentration of Al(III) with 10 mL solution. Under the optimal conditions, the detection limit of this method for Al(III) is 0.09 ng mL(-1), and the relative standard deviation is 4.7% at 10 ng mL(-1) Al(III) level (n=7). The proposed method has been applied for determination of trace amount of aluminum in biological and water samples with satisfactory results.     

Fully automated determination in the low nanogram per liter level of different classes of drugs of abuse in sewage water by on-line solid-phase extraction-liquid chromatography-electrospray-tandem mass spectrometry

The present work describes the first fully automated method, based on on-line solid-phase extraction (SPE)-liquid chromatography-electrospray-tandem mass spectrometry, developed for the determination of drugs of abuse (17 compounds and metabolites belonging to the classes of amphetaminics, cannabinoids, cocainics, opiates, and lysergics) in sewage waters. On-line SPE is performed by passing 5 mL of the water sample through a PLRP-s cartridge for analytes measured in positive ionization mode (all but cannabinoids) and through an Oasis HLB cartridge for analytes measured in negative ionization mode (cannabinoids). For unequivocal identification and confirmation two selected reaction monitoring transitions are registered per compound, thus achieving the four identification points requested by the European Union for banned substances. Quantitation is performed by the internal standard method, indispensable to correct for matrix effects. The main advantages of the method developed are high sensitivity (limits of determination between 0.69 and 5.97 ng/L), selectivity and reliability of results, minimum sample manipulation, full automation, and fairly high throughput (analysis time per sample is 2 x 35 min). As a part of the validation procedure, the method developed has been applied to the analysis of various influent and effluent samples from four Spanish sewage treatment plants.     

Evaluation of hydrazine reduction by cellulose acetate filters using infrared tunable diode laser spectroscopy

Cellulose acetate (CA) filters have been investigated to determine their hydrazine (N2H4) breakthrough characteristics using a system based on tunable diode laser absorption spectroscopy (TDIAS). The breakthrough mass loading sorption curves for hydrazine were dependent on both the flow rate and the concentration. In experiments using a 4.5 ppmv hydrazine standard, the amounts of hydrazine retained by the CA filter were 4.25 microg at a flow rate of 2.82 L/min and 65 microg at a flow rate of 0.28 L/min. These loadings are much greater than the 31.5 ng/cigarette of hydrazine reported in smoke for unfiltered cigarettes. Further, CA filters exposed to four and eight puffs of smoke actually made the filter more efficient in retaining hydrazine compared to CA filters that had not been exposed to smoke. Therefore, if hydrazine is present in smoke at the levels reported in unfiltered cigarettes, all of the hydrazine would be trapped by the CA filter, and would be unable to break through during smoking. A unique feature of this analytical method is that the instrument does not require calibration after molecular parameters have been determined, in this case from previously acquired quantitative hydrazine FT-IR reference spectra.     

Solid phase extraction of lead and cadmium using solid sulfur as a new metal extractor prior to determination by flame atomic absorption spectrometry

A new method using a mini-column packed with sulfur as a new solid phase extractor has been developed for simultaneous preconcentration of lead and cadmium in water samples prior to flame atomic absorption spectrometric determinations. The effects of various parameters such as pH, flow rate of sample and eluent, type and concentration of eluent, sample volume, amount of adsorbent and interfering ions have been studied. The calibration graph was linear in the range of 10-300 and 1-20 ng mL(-1) for lead and cadmium, respectively. The limit of detection based on three times the standard deviation of the blank (3S(b)) was 3.2 and 0.2 ng mL(-1) (n=10) for lead and cadmium, respectively. A preconcentration factor of 250 was achieved in this method. The proposed procedure was applied to the determination of metal ions in tap, river and wastewater samples.     

Flame atomic absorption spectrometric determination of trace quantities of cadmium in water samples after cloud point extraction in Triton X-114 without added chelating agents

A new micell-mediated phase separation method for preconcentration of ultra-trace quantities of cadmium as a prior step to its determination by flame atomic absorption spectrometry has been developed. The method is based on the cloud point extraction (CPE) of cadmium in iodide media with Triton X-114 in the absence of any chelating agent. The optimal extraction and reaction conditions (e.g., acid concentration, iodide concentration, effect of time) were studied, and the analytical characteristics of the method (e.g., limit of detection, linear range, preconcentration, and improvement factors) were obtained. Linearity was obeyed in the range of 3-300 ng mL(-1) of cadmium. The detection limit of the method is 1.0 ng mL(-1) of cadmium. The interference effect of some anions and cations was also tested. The method was applied to the determination of cadmium in tap water, waste water, and sea water samples.     

镁铝铁层状金属氢氧化物固相萃取有机磷农药的研究

建立镁铝铁层状金属氢氧化物(Mg-Al-Fe-LDH)复合材料固相萃取气相色谱质谱法(GC-MS)测定水中的敌敌畏,乐果,氯吡硫磷,水胺硫磷的分析方法.复合材料用量为2 g,萃取12 min,二氯甲烷作为洗脱剂,洗脱剂用量为2 mL,洗脱时间1 min,4种农药的质量浓度在0.01～10 ng/mL范围内与峰面积线性关...     

A device for automated direct sampling and quantitation from solid-phase sorbent extraction cards by electrospray tandem mass spectrometry

A new solid-phase extraction (SPE) device in the 96-well format (SPE Card) has been employed for automated off-line sample preparation of low-volume urine samples. On-line automated analyte elution via SPE and direct quantitation by micro ion spray mass spectrometry is reported. This sample preparation device has the format of a microtiter plate and is molded in a plastic frame which houses 96 separate sandwiched 3M Empore sorbents (0.5-mm-thickness, 8-microm particles) covered on both sides by a microfiber support material. Ninety-six discrete SPE zones, each 7 mm in diameter, are imbedded into the sheet in the conventional 9-mm pitch (spacing) of a 96-well microtiter plate. In this study one-quarter of an SPE Card (24 individual zones) was used merely as a convenience. After automated off-line interference elution of applied human urine from 24 samples, a section of SPE Card is mounted vertically on a computer-controlled X, Y, Z positioner in front of a micro ion spray direct sampling tube equipped with a beveled tip. The beveled tip of this needle robotically penetrates each SPE elution zone (sorbent disk) or stationary phase in a serial fashion. The eluted analytes are sequentially transferred directly to a microelectrosprayer to obtain tandem mass spectrometric (MS/MS) analysis. This strategy precludes any HPLC separation and the associated method development. The quantitative determination of Ritalin (methylphenidate) from fortified human urine samples is demonstrated. A trideuterated internal standard of methylphenidate was used to obtain ion current response ratios between the parent drug and the internal standard. Human control urine samples fortified from 6.6 to 3300 ng/mL (normal therapeutic levels have been determined in other studies to be between 50 and 100 ng/mL urine) were analyzed and a linear calibration curve was obtained with a correlation coefficient of 0.9999, where the precision of the quality control (QC) samples ranged from 9.6% at the 24 ng/mL QC level to 1.2% at the 3000 ng/mL QC level, and the accuracy for the four levels of QC samples ranged from 98.1% to 100.3%. The QC samples were prepared at four concentrations which included 24, 240, 1200, and 3000 ng/mL, respectively. The run time per sample in this work was 1.5 min not including the sample preparation time.     

Determination of proanthocyanidins in grape products by liquid chromatography/mass spectrometric detection under low collision energy

A method has been established for the identification of proanthocyanidins and quantification of individual monoproanthocyanidins using liquid chromatography/electrospray ionization-mass spectrometric detection (LC/ESI-MSD) for raw grape products. The separated monoproanthocyanidins and oligoproanthocyanidins were individually analyzed and identified by their molecular ion peaks using LC/MS. Using HPLC/ESI-MSD, the proanthocyanidin monomers, (+)-catechin (C), (-)-epicatechin (EC), (-)-catechin gallate (CG), and (-)-epicatechin gallate (ECG) in grape products were successfully quantified by LC/MS/MS detection of protonated molecular ions and characteristic fragment ions for each component under the optimized low collision energy level of 20%. For the investigated concentration ranges of C (21.88-11,200 ng/mL), EC (21.10-10,800 ng/mL), CG (36.72-18,800 ng/mL), and ECG (39.84-20,400 ng/mL), good linearities (r2 > 0.99) for standard curves were obtained. Validation of this method showed an accuracy that was well below 15% and precision (RSD) within 8% for the four compounds. The method proposed here is simple, sensitive, and allows a direct sample preparation procedure. This is the first method that enables the determination of individual monoproanthocyanidins in grape products without any solid-phase extraction.     

A simple and selective spectrophotometric flow injection determination of trace amounts of ruthenium by catalytic oxidation of safranin-O

In this work, a simple, selective and rapid flow injection method has been developed for determination of ruthenium. The method is based on its catalytic effect on the oxidation of safranin-O by metaperiodate. The reaction was monitored spectrophotometrically by measuring safranin-O absorbance at lambdamax=521. The reagents and manifold variables, which have influences on the sensitivity, were investigated and the optimum conditions were established. The optimized conditions made it possible to determine ruthenium in the ranges of 0.4-20.0 ng/mL (DeltaA=0.2819CRu+1.1840) and 20.0-100.0 ng/mL (DeltaA=0.0984CRu+7.9391) with a detection limit of 0.095 ng/mL and a sample rate of 30+/-5 samples/h. Relative standard deviation for the five replicate measurements was less than 1.84%. The proposed method has been successfully applied for analysis of ultra trace amounts of ruthenium in real samples.     

Simultaneous determination of the pesticides carbaryl and thiabendazole in environmental samples by a three-dimensional derivative variable-angle and a synchronous room-temperature phosphorescence spectroscopy

A three-dimensional derivative variable-angle synchronous scanning (DVASS) and a synchronous scanning (SS) heavy-atom room-temperature phosphorimetry (HAI-RTP) method are reported, for the first time, to identify and quantify the spectral overlapping phosphorescent pesticides thiabendazole (TBZ) and carbaryl (CBL). These pesticides are widely used in agriculture. The phosphorescence emission of the two compounds was obtained using sodium sulfite as the O2 scavenger and an external heavy atom salt. A careful selection of these experimental variables has been carried out. The increase of selectivity afforded by the DVASS and the SS methodology permitted the demonstration of its applicability to the simultaneous determination of phosphorescent signals of these two pesticides with overlapping spectral profiles. Limits of detection ranged between 1.4 ng/mL for TBZ and 1.7 ng/mL for CBL. The proposed method has been satisfactorily applied to the analysis of both pesticides in different types of water samples.