Application of carbon ionic liquid electrode for the electrooxidative determination of catechol

A carbon ionic liquid electrode (CILE) was constructed using graphite powder mixed with N-butylpyridinium hexafluorophosphate (BPPF₆) in place of paraffin as the binder, which showed strong electrocatalytic activity to the direct oxidation of catechol. In pH 3.0 phosphate buffer solution (PBS) a pair of redox peaks appeared on the CILE with the anodic and the cathodic peak potential located at 387 and 330 mV (vs. SCE), respectively. The electrochemical behaviors of catechol on the CILE were carefully investigated, and the electrochemical parameters were calculated with the results of the electrode reaction standard rate constant k_s as 1.27 s⁻¹, the charge-transfer coefficient α as 0.58 and the electron transferred number n as 2. Under the selected conditions, the anodic peak current increased linearly with the catechol concentration over the range from 1.0 × 10⁻⁶ to 8.0 × 10⁻⁴ mol L⁻¹ by cyclic voltammetry at the scan rate of 100 mV s⁻¹. The detection limit was calculated as 6.0 × 10⁻⁷ mol L⁻¹ (3σ). The CILE showed good ability to separate the electrochemical responses of catechol and ascorbic acid (AA) with the anodic peak potential separation as 252 mV (vs. SCE). The proposed method was further applied to the synthetic samples determination with satisfactory results.     

Electrochemical DNA biosensor for the detection of interaction between di[azino-di(5,6-azafluorene)-κ-NN′]dichlormanganous and DNA

A new Mn(II) complex of MnL₂Cl₂ (L = azino-di(5,6-azafluorene)-κ²-NN′) was synthesized and utilized as an electrochemical indicator for the determination of hepatitis B virus (HBV) based on its interaction with MnL₂Cl₂. The electrochemical behavior of interaction of MnL₂Cl₂ with salmon sperm DNA was investigated on glassy carbon electrode (GCE). In the presence of salmon sperm DNA, the peak current of [MnL₂]²⁺ was decreased and the peak potential was shifted positively without appearance of new peaks. The binding ratio between [MnL₂]²⁺ and salmon sperm DNA was calculated to be 2:1 and the binding constant was 3.72 × 10⁸ mol² L⁻². The extent of hybridization was evaluated on the basis of the difference between signals of [MnL₂]²⁺ with probe DNA before and after hybridization with complementary sequence. Control experiments performed with non-complementary and mismatch sequence demonstrated the good selectivity of the biosensor. With this approach, a sequence of the HBV could be quantified over the range from 1.76 × 10⁻⁸ to 1.07 × 10⁻⁶ mol L⁻¹, with a linear correlation of r = 0.9904 and a detection limit of 6.80 × 10⁻⁹ mol L⁻¹. Additionally, the binding mechanism was preliminarily discussed. The mode of interaction between MnL₂Cl₂ and DNA was found to be primary intercalation binding.     

Electrochemical sensor for hydroperoxides determination based on Prussian blue film modified electrode

An electrochemical sensor for hydroperoxides determination was investigated. The sensor was based on the electrocatalytic reduction of hydroperoxides on Prussian blue (PB)-modified glassy carbon electrode. The modified electrode possesses a high electrocatalytic effect towards all studied peroxides with the highest effect obtained with H₂O₂ followed by tert-butyl hydroperoxide (TBH), cumene hydroperoxide (CH) and linoleic acid hydroperoxide (LAH). In addition, the modified electrode showed a good stability and a fast response time (<20 s). The lower detection limits of H₂O₂, TBH, CH and LAH were found to be 10⁻⁷ mol L⁻¹, 2 × 10⁻⁷ mol L⁻¹, 3.5 × 10⁻⁷ mol L⁻¹ and 4 × 10⁻⁷ mol L⁻¹, respectively. The electrochemical sensor was then applied for amperometric determination of peroxide value (PV) in edible oil at an applied potential of 50 mV (vs. Ag/AgCl (1 M KCl)). A good linearity has been found in the range 0.02–1.0 mequiv. O₂/kg, with a detection limit (S/N = 3) of 0.001 mequiv. O₂/kg. The precision of the method (R.S.D., n = 9) for within and between-days is better than 1.9% and 2.7%, respectively at 0.1 mequiv. O₂/kg. The method was successfully applied to the determination of PV in real edible oil samples with an excellent agreement with results obtained with the official standard procedure. The proposed method is accurate, simple, cheap and could be used to control edible oil rancidity with a high sample throughputs (more than 120 samples/h).     

Direct amperometric determination of l-ascorbic acid (Vitamin C) at octacyanomolybdate-doped-poly(4-vinylpyridine) modified electrode in fruit juice and pharmaceuticals

The glassy carbon electrode (GCE) modified with Mo(CN)₈⁴⁻-incorporated-poly(4-vinylpyridine) (PVP/Mo(CN)₈⁴⁻), which has been recently shown to possess several attractive attributes as an efficient electrocatalytic electrode for l-ascorbic acid oxidation and its estimation, is used for l-ascorbic acid estimation directly in orange fruit juice and Celin tablet in a 0.1 M H₂SO₄ acid solution without any special treatment. Constant potential amperometry at 570 mV (saturated calomel electrode, SCE) in stirred solutions is used for this purpose. A good correlation is attained with the official titrametric method. To understand the possible electrocatalytic reaction mechanism for the electro-oxidation of l-ascorbic acid, calibration graphs over the range 1 × 10⁻⁵ to 1 × 10⁻² mol dm⁻³ l-ascorbic acid are compared for the three electrodes, ca. PVP/Mo(CN)₈⁴⁻, undoped PVP, and GCE; the curvature at high ascorbic acid concentration for the PVP/Mo(CN)₈⁴⁻ electrode is explained in terms of Michaelis–Menten (MM) saturation kinetics. The apparent MM constant (K_M), the maximum catalytic current (i_M), the complex decomposition rate constant (k_c), and the heterogeneous modified electrode rate constant (k^′_ME) are calculated from three different approaches. A reasonably high value of ≈1 × 10⁻² cm s⁻¹ is obtained for k^′_ME, indicating efficient l-ascorbic acid mediation at the PVP/Mo(CN)₈⁴⁻ electrode, thus accounting for quite a high sensitivity of this modified film electrode compared to several other modified electrodes.     

Anodic stripping voltammetric determination of copper(II) using a functionalized carbon nanotubes paste electrode modified with crosslinked chitosan

The development and application of a functionalized carbon nanotubes paste electrode (CNPE) modified with crosslinked chitosan for determination of Cu(II) in industrial wastewater, natural water and human urine samples by linear scan anodic stripping voltammetry (LSASV) are described. Different electrodes were constructed using chitosan and chitosan crosslinked with glutaraldehyde (CTS-GA) and epichlorohydrin (CTS-ECH). The best voltammetric response for Cu(II) was obtained with a paste composition of 65% (m/m) of functionalized carbon nanotubes, 15% (m/m) of CTS-ECH, and 20% (m/m) of mineral oil using a solution of 0.05 mol L⁻¹ KNO₃ with pH adjusted to 2.25 with HNO₃, an accumulation potential of −0.3 V vs. Ag/AgCl (3.0 mol L⁻¹ KCl) for 300 s and a scan rate of 100 mV s⁻¹. Under these optimal experimental conditions, the voltammetric response was linearly dependent on the Cu(II) concentration in the range from 7.90 × 10⁻⁸ to 1.60 × 10⁻⁵ mol L⁻¹ with a detection limit of 1.00 × 10⁻⁸ mol L⁻¹. The samples analyses were evaluated using the proposed sensor and a good recovery of Cu(II) was obtained with results in the range from 98.0% to 104%. The analysis of industrial wastewater, natural water and human urine samples obtained using the proposed CNPE modified with CTS-ECH electrode and those obtained using a comparative method are in agreement at the 95% confidence level.     

Analysis of interface states of metal–insulator–semiconductor photodiode with n-type silicon by conductance technique

A metal–insulator–semiconductor photodiode (MIS-PD) as active layer with n-type silicon as interdigitated Schottky electrodes has been fabricated. The current–voltage characteristics, density of interface states and photovoltaic properties of the MIS-PD diode have been investigated. The diode has a metal–insulator–semiconductor configuration with ideality factor higher than unity. The electronic parameters (ideality factor, series resistance and barrier height) of the diode were found to be 1.94, 2.23 × 10⁴ Ω and 0.74, respectively. At voltages between 0.13 and 0.50 V, the charge transport mechanism of the diode is controlled by space charge-limited current mechanism. The interface state density of the diode was found to vary from 5.54 × 10¹² to 5.67 × 10¹² eV⁻¹ cm⁻² with bias voltage. The Au/SiO₂/n-Si/Al device shows a photovoltaic behavior with a maximum open circuit voltage V_oc of 97.7 mV and short-circuit current I_sc of 17.4 μA under lower illumination intensities. The obtained electronic parameters confirm that the Au/SiO₂/n-Si/Al diode is a MIS type photodiode.     

A sensitive nonenzymatic hydrogen peroxide sensor based on DNA–Cu complex electrodeposition onto glassy carbon electrode

In this paper, DNA–Cu²⁺ complex was electrodeposited onto the surface of glassy carbon (GC) electrode, which fabricated a DNA–Cu²⁺/GC electrode sensor to detect H₂O₂ with nonenzyme. Cyclic voltammogram of DNA–Cu²⁺/GC electrode showed a pair of well-defined redox peaks for Cu²⁺/Cu⁺. Moreover, the electrodeposited DNA–Cu²⁺ complex exhibited excellent electrocatalytic behavior and good stability for the detection of H₂O₂. The effects of Cu²⁺ concentration, electrodeposition time and determination conditions such as pH value, applied potential on the current response of the DNA–Cu²⁺/GC electrode toward H₂O₂ were optimized to obtain the maximal sensitivity. The linear range for the detection of H₂O₂ is 8.0 × 10⁻⁷ M to 4.5 × 10⁻³ M with a high sensitivity of −40.25 μA mM⁻¹, a low detection limit of 2.5 × 10⁻⁷ M and a fast response time of within 4 s. In addition, the sensor has good reproducibility and long-term stability and is interference free.     

In vivo monitoring of oxidative burst induced by ultraviolet A and C stress for oilseed rape by microbiosensor

In this paper, poly-o-phenylenediamine and Pt microparticle modified Pt electrode (POPD/Pt-MP/Pt) as microbiosensor has been developed to monitor in vivo oxidative burst induced by ultraviolet A (UV-A) and ultraviolet C (UV-C) radiation stress in oilseed rape (Brassica napus L.). Twice oxidative bursts were detected, appearing at 2 and 25 h, respectively. According to the peak area of amperometry, the amount of H₂O₂ induced by UV stress was estimated to be 6.2 × 10⁻¹⁰ and 3.1 × 10⁻¹⁰ mol for such two oxidative bursts in detected leafstalk, respectively. This novel microbiosensor provides an effective tool for studying the defense reaction of the plant in the situation of UV stress and probing the antioxidative mechanism of the antioxidative enzyme.     

Bean sprout peroxidase biosensor based on l-cysteine self-assembled monolayer for the determination of dopamine

A new bean sprout peroxidase was immobilized on a gold electrode modified with self-assembled monolayers (SAM) of l-cysteine for the determination of dopamine in pharmaceutical samples using square wave voltammetry. In the bean sprout–(SAM)–Au electrode, the peroxidase, in the presence of hydrogen peroxide, catalyzes the oxidation of dopamine to the corresponding quinone, which is electrochemically reduced back to dopamine at +0.15 V vs. Ag/AgCl. The performance and the factors influencing the response of this biosensor were studied in detail. The best performance was obtained using 0.1 mol L⁻¹ phosphate buffer solution (pH 6.0), 6.0 × 10⁻⁵ mol L⁻¹ hydrogen peroxide, frequency of 100 Hz, pulse amplitude of 80 mV and scan increment of 4.0 mV. The analytical curve was linear for dopamine concentrations from 9.91 × 10⁻⁶ to 2.21 × 10⁻⁴ mol L⁻¹ and the detection limit was 4.78 × 10⁻⁷ mol L⁻¹. The recovery of dopamine ranged from 98.0 to 111.8% and the relative standard deviation was 3.1% for a solution containing 1.30 × 10⁻⁵ mol L⁻¹ dopamine (n = 6). The lifetime of this biosensor was 15 days (at least 300 determinations). The results obtained for dopamine determination in pharmaceutical formulations using the proposed bean sprout–SAM–Au electrode were in agreement with those obtained with the standard method at the 95% confidence level.     

Electrochemical sensor for simultaneous detection of ascorbic acid, uric acid and xanthine based on the surface enhancement effect of mesoporous silica

The measurement of ascorbic acid (AA), uric acid (UA) and xanthine (XA) is very important in the clinical diagnosis because many diseases have been found to be associated with their concentrations. Herein, an electrochemical sensor using mesoporous SiO₂ as sensing material was firstly developed for the simultaneous detection of AA, UA and XA. With distinctive properties such as uniform porous networks, large surface area and high sorption ability, the mesoporous SiO₂ sensor exhibits remarkable surface enhancement effect, and greatly increases the response signals of AA, UA and XA. In addition, the electrochemical responses of coexistence of AA, UA and XA were studied, and three well-shaped oxidation peaks were observed at 0.00, 0.25 and 0.63 V. Further studies suggest that their oxidation takes place independently and has no mutual interference. This sensor possesses high sensitivity, and the limit of detections are 3.0 × 10⁻⁶ mol L⁻¹, 1.0 × 10⁻⁷ mol L⁻¹ and 7.5 × 10⁻⁷ mol L⁻¹ for AA, UA and XA. Finally, the mesoporous SiO₂ sensor was successfully employed to detect AA, UA and XA in the urine and blood serum samples.     

Modified glassy carbon electrode with multiwall carbon nanotubes as a voltammetric sensor for determination of noscapine in biological and pharmaceutical samples

A simple and highly sensitive method is described for direct voltammetric determination of noscapine in blood and pharmaceutical sample. Glassy carbon electrode with effective method is modified with multiwall carbon nanotubes (MWNTs) to cause activation of multiwall carbon nanotubes structures for electrocatalyzes of noscapine oxidation. The cyclic voltammetric (CV) results indicated that MWNTs remarkably enhances electrocatalytic activity toward the oxidation of noscapine, which is leading to considerable improvement of anodic peak current for noscapine, and allows the development of a highly sensitive voltammetric sensor for detection of noscapine in pharmaceutical and clinical samples. Under the optimum condition, the calibration curve was linear in the concentration range 4.0 × 10⁻⁷–1.0 × 10⁻⁴ mol L⁻¹ with the detection limit of 8.0 × 10⁻⁸ mol L⁻¹ and relative standard deviation (R.S.D.%) lower than 1.0% (n = 5). Finally, some kinetic parameters were determined and multistep mechanism for oxidation of noscapine for first time was proposed.     

Direct electrochemistry and electrocatalysis with horseradish peroxidase immobilized in polyquaternium-manganese oxide nanosheet nanocomposite films

A novel biocompatible polyquaternium (QY)-manganese oxide nanosheet (MNS) nanocomposite has been prepared and shown to be a promising matrix for horseradish peroxidase (HRP) immobilization. The resulting HRP-QY-MNS film was characterized by Fourier transform infrared (FTIR) and circular dichroism (CD) spectroscopy, which indicated that HRP retained its native structure in the nanocomposite film. An HRP-QY-MNS film-modified glassy carbon electrode exhibited a pair of well-defined and quasi-reversible cyclic voltammetric peaks centered at −0.272 V (vs. Ag/AgCl) in pH 7.0 phosphate buffer solution. The direct electrochemical behavior of HRP was greatly enhanced in the QY-MNS nanocomposite film compared with that in single-component QY or MNS films. The immobilized HRP showed excellent electrocatalysis in the reduction of hydrogen peroxide (H₂O₂), which was exploited in the construction of an H₂O₂ biosensor. The linear range of the biosensor for H₂O₂ was found to be from 1.0 × 10⁻⁷ to 3.2 × 10⁻⁵ M with a correlation coefficient of 0.998. The detection limit was 7.8 × 10⁻⁸ M at a signal-to-noise ratio of 3. The biosensor exhibited rapid response and good long-term stability.     

A sensitive and selective sensor for dopamine determination based on a molecularly imprinted electropolymer of o-aminophenol

A simple and reliable method was proposed for preparing a selective dopamine (DA) sensor based on a molecularly imprinted electropolymer of o-aminophenol. The sensor is selective for the determination of DA in the presence of high concentrations of ascorbic acid (AA), with a maximum molar ratio of 1/1000. The molecular imprinted (MIP) sensor was tested by cyclic voltammetry (CV) as well as differential pulse voltammetry (DPV) to verify the changes in oxidative currents of ferricyanide. In optimized conditions, DA at concentrations of 2 × 10⁻⁸ to 0.25 × 10⁻⁶ mol/L could be determined with a detection limit of 1.98 × 10⁻⁹ mol/L (S/N = 3). The MIP sensor showed high selectivity, sensitivity, and reproducibility. Determination of DA in simulated samples of dopamine hydrochloride showed good recovery.     

A novel microbial biosensor based on Circinella sp. modified carbon paste electrode and its voltammetric application

Microbial biosensors have been developed for voltammetric determination of various substances. This paper describes the development of a new biosorption based microbial biosensor for determination of Cu²⁺. The developed biosensor is based on carbon paste electrode consisting of whole cells of Circinella sp. Cu²⁺ was preconcentrated on the electrode surface at open circuit and then cathodically detected with the reduction of Cu²⁺. The voltammetric responses were evaluated with respect to percentage cell loading in the carbon paste, preconcentration time, pH of preconcentration solution, scan rate and interferences. The optimum response was realized by biosensor constructed using 5 mg of dry cell weight per 100 mg of carbon paste in pH 5.5 preconcentration solution. Under the optimum experimental conditions, the developed microbial biosensor exhibited an excellent current response to Cu²⁺ over a linear range from 5.0 × 10⁻⁷ to 1.0 × 10⁻⁵ M (r² = 0.9938) with a detection limit of 5.4 × 10⁻⁸ M (S/N = 3). The microbial biosensor had good sensitivity and reproducibility (R.S.D. 4.3%, n = 6). Finally, the applicability of the proposed microbial biosensor to voltammetric determination of Cu²⁺ in real sample was also demonstrated and validated with atomic absorption spectrophotometric (AAS) method.     

Polythiophene based fluorescence sensors for acids and metal ions

Poly(thiophene-3-yl-acetic acid 8-quinolinyl ester) is a fluorescent material and it shows fluorescence at 540 nm. The fluorescence of poly (thiophene-3-yl-acetic acid 8-quinolinyl ester) has been studied in the presence of acids, metal ions, nucleotides and protein (l-proline). The fluorescence of polymer is quenched by the addition of HCl which could be recovered by the addition of equivalent amount of alkali. The Stern–Volmer quenching coefficient for HCl is calculated and found to be 141 M⁻¹. Moreover quenching depends on concentration of HCl. Similarly, the fluorescence of polymer is quenched by copper, cadmium and lead metal ions and quenching is sensitive to concentrations of metal ions. The Stern–Volmer quenching coefficient is 2.285 × 10³ M⁻¹ for Cu²⁺ ions, 2.287 × 10³ M⁻¹ for Cd²⁺ ions and 3.7 × 10⁴ M⁻¹ for Pb²⁺ ions. In Al³⁺, Zn²⁺, nucleotides and protein (l-proline), the fluorescence is exorbitantly increased.     

Corrosion resistant and adsorbent plasma polymerized thin film

Adsorbent and corrosion resistant films are useful for sensor development. Therefore, the aim of this work is the production and characterization of plasma polymerized fluorinated organic ether thin films for sensor development. The polymerized reactant was methyl nonafluoro(iso)butyl ether. Infrared Spectroscopy showed fluorinated species and eventually CO but CH_n is a minor species. Contact angle measurements indicated that the film is hydrophobic and organophilic but oleophobic. Optical microscopy reveals not only a good adherence on metals and acrylic but also resistance for organic solvents, acid and basic aqueous solution exposure. Double layer and intermixing are possible and might lead to island formation. Quartz Crystal Microbalance showed that 2-propanol permeates the film but there is no sensitivity to n-hexane. The microreactor manufactured using a 73 cm long microchannel can retain approximately 9 × 10⁻⁴ g/cm² of 2-propanol in vapor phase. Therefore, the film is a good candidate for preconcentration of volatile organic compounds even in corrosive environment.     

Structural and electrical properties of mixed oxides of manganese and vanadium: A new semiconductor oxide thermistor material

Binary oxides of manganese and vanadium have been synthesized by solid state sintering, in which the mass ratio of the individual components Mn₂O₃ and VO₂ have been varied from 90:10 to 5:95. The bulk ceramic samples were characterized by X-ray diffraction and scanning electron microscopy with energy dispersive X-ray analysis. The initial compositions either rich in Mn₂O₃ or in equi-proportion by mass with VO₂ yield β-Mn₂V₂O₇ or a new crystalline form of Mn₂V₂O₇, with unit cell parameters: a = 7.73091 Å, b = 6.640788 Å, c = 6.70779 Å α = γ = 90° and β = 98.7086° which is designated as γ-Mn₂V₂O₇. The compositions, richer in VO₂ produce MnV₂O₆ co-existing with V₂O₅ the proportion of which increases with increase in VO₂. The surface microanalysis shows a spherical-granular morphology in Mn₂V₂O₇ structure and plate/rod-like structures co-existing with granular morphology in case of MnV₂O₆ together with V₂O₅. The electrical parameters of the negative temperature coefficient thermistors were determined. Depending on the constituent oxide composition, the NTC thermistors showed room temperature resistivity in the range of 6.52 × 10² to 6.1 × 10⁶ Ω-cm. The thermistor constant and activation energy are in the range of 0.12–0.458 eV and 1393–4801 K, respectively.     

Molecular valve consisting of poly(acrylic acid) gel

A molecular valve, consisting of poly(acrylic acid) gel-coated Au mesh, was developed based on volume change of the gel in response to cation concentration. The valve closed when concentration of cations such as H⁺, Na⁺, K⁺, Ca²⁺, Cu²⁺, or Al³⁺ was low, whereas opened upon increase in its concentration. The valve re-closed when water was flowed. The concentration where the valve opens was found to increase in the order of Al³⁺, Ca²⁺, and Na⁺ (2 × 10⁻⁴, 5 × 10⁻⁴, and 6 × 10⁻³ M, respectively). The response to Cu²⁺ ion showed similar behaviour, but the opening concentration was ca. 2 × 10⁻⁴ M, which is lower than that of Ca²⁺ ion. The valve appeared to close over the pH range from 3 to 12, whereas to open below and above it. The fastest response time to open the valve (less than 1 min) was obtained for a solution of pH 1–2. The valve showed repeatability at least 25 cycles upon successive loading of a solution of pH 2 and water. Effects of anions and pressure were also studied.     

A sensitive nitric oxide microsensor based on PBPB composite film-modified carbon fiber microelectrode

In this work, a sensitive electrochemical microsensor of nitric oxide (NO) was reported. The microsensor was constructed by coating PBPB composite on carbon fiber microelectrodes (CFME). The NO microsensor displayed excellent electrochemical activity toward the oxidation of NO and have the virtue of good stability, reproducibility and high sensitivity. Under optimal working conditions, the oxidation current of NO at this microsensor exhibited a good linear relationship with NO concentration in the range of 3.6 × 10⁻⁸ to 8.9 × 10⁻⁵ mol/L with a low detection limit of 3.6 × 10⁻⁹ mol/L (S/N = 3). The microsensor was successfully applied to the direct and real-time detection of NO release from biological samples, foreseeing the promising applications of this microsensor in fields like biology and medicine.     

An integrated chemical sensor with multiple ion and gas sensors

An integrated chemical sensor with multiple ion and gas sensors, composed of four ISFETs (pH, Na⁺, K⁺ and Cl⁻) and two gas sensors (P_O2 and P_CO2) on a 4 mm × 4 mm chip, is realized using semiconductor processing. The ISFETs are based on an Si₃N₄-gate ISFET, and use polymeric membrane except for the pH ISFET. The P_O2 sensor is a miniaturized Clark-type sensor, consisting of a Pt cathode and Ag/AgCl anode patterned by the lift-off process. The P_CO2 sensor is a miniaturized Severinghaus-type sensor using a pH ISFET. All of the ISFETs show sensitivities over 50 mV/decade, and a linear range between 1 × 10⁻⁴ and 5 × 10⁻¹ mol/l. The sensitivities of the P_O2 and P_CO2 sensors are 0.35 nA/mmHg and 42 mV/decade, respectively, and their response times are 30 s and 1 min, respectively. The integrated chemical sensor with multiple ion and gas sensors could be used for clinical analysis.