Effect of Magnesium Oxide and the Testing Rate on the Viscosity and Adhesion Properties of Epoxidized Natural Rubber/Acrylonitrile–Butadiene Rubber Blend Based Adhesives

The effect of magnesium oxide loading on the adhesion properties of epoxidized natural rubber (ENR 50)/acrylonitrile–butadiene rubber (NBR)-based pressure-sensitive adhesives was systematically investigated using 40 parts per hundred parts of rubber (phr) of coumarone–indene resin as the tackifier. The concentration range of magnesium oxide was from 10–50 phr. Toluene and polyethylene terephthalate (PET) films were selected as the solvent and the substrate, respectively, throughout the experiment. A Sheen hand coater was used to coat the adhesive onto the PET substrate at various coating thicknesses. The viscosity of the adhesive was measured using a Brookfield viscometer, whereas the loop tack, peel strength, and shear strength were determined using an adhesion tester operating at 10–60 cm/min. The results indicate that the viscosity increases with magnesium oxide loading, an observation which is attributed to the concentration effect of the filler. However, loop tack, peel strength, and shear strength increase with magnesium oxide loading up to 30 phr before decreasing upon further addition of the filler. This observation is ascribed to the effect of a varying degree of wettability of the adhesive, which culminates at 30 phr of magnesium oxide loading. At a fixed loading of magnesium oxide, all the adhesion properties of adhesives increase upon increasing the coating thickness and rate of testing.     

Effect of Barium Chloride Filler on the Adhesion Properties of Epoxidized Natural Rubber (ENR 25)-Based Adhesives

The adhesion properties of epoxidized natural rubber (ENR 25)-based adhesive were studied using barium chloride, coumarone-indene resin and toluene as the filler, tackifier and solvent respectively. Viscosity was determined by a Brookfield Viscometer whereas tack, shear and peel strength was measured by a Llyod Adhesion Tester. Results show that viscosity of adhesive increases gradually with increasing barium chloride loading. Loop tack, shear and peel strength indicates a maximum value at 10 parts per hundred parts of rubber (phr) of barium chloride, an observation that is attributed to the maximum wettability and compatibility of adhesive on the substrate.     

Effect of Coumarone-Indene Resin on Adhesion Property of SMR 20-Based Pressure-Sensitive Adhesives

The viscosity, tack, and peel strength of a natural rubber (SMR 20)–based pressure-sensitive adhesive (PSA) was studied using coumarone-indene resin as the tackifier. The resin loading was varied from 0–80 parts per hundred parts of rubber (phr). Toluene was used as the solvent throughout the experiment. The viscosity of PSA was measured using a Haake Rotary Viscometer whereas loop tack and peel strength were determined using a Lloyd Adhesion Tester. PSA was coated onto the substrates using a SHEEN hand coater to give a coating thickness of 60 μm and 120 μm. Results show that the viscosity and tack of the adhesive increases with resin content due to the concentration effect of tackifier resin. However, for the peel strength, it increases up to 40 phr of resin for both coating thickness, an observation that is attributed to the wettability of substrates.     

Effect of silica on viscosity,tack, and shear strength of epoxidized natural rubber‐based pressure‐sensitive adhesives in the presence of coumarone‐indene resin

The viscosity, loop tack, and shear strength of silica‐filled epoxidized natural rubber (ENR 25 and ENR 50 grade) adhesive were investigated using coumarone‐indene as the tackifying resin. Silica loading was varied from 10–50 parts per hundred parts of rubber (phr), whereas the coumarone‐indene concentration was fixed at 40 phr. Toluene was used as the solvent throughout the study. Polyethylene terephthalate substrate was coated at various adhesive coating thicknesses, i.e., 30, 60, 90, and 120 μm using a SHEEN Hand Coater. Viscosity of the adhesive was determined by a HAAKE Rotary Viscometer whereas loop tack and shear strength were measured by a Llyod Adhesion Tester operating at 30 cm/min. Result shows that viscosity of the adhesive increases gradually with increase of silica loading due to the concentration effect of the filler. Both loop tack and shear strength show maximum value at 40 phr silica for ENR 25. However, the respective values for ENR 50 are 20 and 40 phr of filler. This observation is attributed to the maximum wettability and compatibility of adhesive on the substrate at the respective silica loadings. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Shear Strength of SMR—Based Pressure-Sensitive Adhesives

The shear strength of Standard Malaysian Rubber (SMR)-based pressure-sensitive adhesives was studied using coumarone-indene resin as the tackifier resin. Three grades of SMR, i.e., SMR L, SMR 10, and SMR 20 were used as the elastomers. The concentration of tackifier resin was varied from 0–80 parts per hundred parts of rubber (phr). Toluene was used as the solvent throughout the experiment to prepare the pressure-sensitive adhesives. A SHEEN hand coater was used to coat the adhesive on the polyethylene terephthalate substrate to give a coating thickness of 30, 60, 90, and 120 µm. Shear strength of the adhesive was determined by using a Texture Analyzer. Results indicate that for a fixed coating thickness, shear strength decreases gradually with increasing resin content for all the rubbers studied. This observation is attributed to the decreasing cohesive strength of adhesive as resin loading is increased. However, for fixed resin content, shear strength increases with increasing coating thickness suggesting that shear strength is thickness-dependent. SMR L consistently shows higher shear strength than SMR 10 and SMR 20 for all coating thickness, an observation, which is attributed to higher purity of SMR L, compared with the latter two rubbers. The shear strength passes through a maximum at 5 min of mastication time, after which it decreases gradually with further mastication.     

Peel and shear strength of pressure‐sensitive adhesives prepared from epoxidized natural rubber

Peel and shear strength of two grades of epoxidized natural rubber (ENR 25 and ENR 50)‐based pressure‐sensitive adhesive was studied. Coumarone‐indene resin was used as the tackifier, whereas toluene was chosen as the solvent throughout the experiment. The tackifier loading was varied from 0 to 80 parts per hundred parts of rubber (phr). A SHEEN hand coater was used to coat the adhesive on substrate to give a coating thickness of 30, 60, 90, and 120 μm. Peel strength and shear strength of the adhesive were determined by using a Lloyd adhesion tester and Texture analyzer, respectively. Results show that maximum peel strength occurs at 40 phr of coumarone‐indene resin for both ENRs studied an observation, which is attributed to the maximum wettability of the substrate. However, the shear strength shows a gradual decrease with increasing tackifier loading because of the decrease in cohesive strength of adhesive. ENR 25 consistently indicates higher peel strength and shear strength than ENR 50. Generally, peel and shear strength increases with coating thickness. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007.     

Effect of zinc oxide on the viscosity and adhesion property of epoxidized natural rubber/acrylonitrile‐butadiene rubber‐based pressure‐sensitive adhesives

Viscosity, loop tack, peel strength, and shear strength of epoxidized natural rubber (ENR 50)/acrylonitrile‐butadiene rubber (NBR)–based pressure‐sensitive adhesive were studied in the presence of zinc oxide. The zinc oxide concentration was varied from 10 to 50 parts by weight per hundred parts of rubber (phr). Coumarone–indene resin with loading of 40 phr was chosen as the tackifier resin. Toluene and polyethylene terephthalate were used as the solvent and coating substrate, respectively, throughout the experiment. The adhesive was coated on the substrate by using a SHEEN hand coater. Viscosity of the adhesive was determined by a Brookfield Viscometer, whereas the loop tack, peel strength, and shear strength were measured by a Lloyd Adhesion Tester operating at 30 cm/min. Results indicate that viscosity increases with zinc oxide concentration owing to the concentration effect. Loop tack and peel strength pass through a maximum value at 20 phr of zinc oxide concentration. This observation is associated with the effect of varying degrees of wettability of the adhesive on the substrate. Shear strength, however, increases steadily with increasing zinc oxide loading owing to the steady increase in cohesive strength. In all cases, the adhesion properties of adhesives increase with increasing coating thicknesses. J. VINYL ADDIT. TECHNOL., 22:410–414, 2016. © 2015 Society of Plastics Engineers     

Effect of zinc oxide and testing rate on the adhesion property of styrene‐butadiene rubber/standard Malaysian rubber blend adhesives

The effect of zinc oxide and testing rate on tack, peel strength, and shear strength of styrene‐butadiene rubber (SBR)/standard Malaysian rubber (SMR L) blend adhesive was investigated using coumarone‐indene resin and toluene as the tackifying resin and solvent, respectively. Zinc oxide concentration was varied from 0–50 parts per hundred parts of rubber (phr). A Lloyd Adhesion Tester operating from 10–60 cm/min was used to determine the adhesion property. Results show that tack and peel strength increases with zinc oxide concentration up to 20 phr of the filler loading. This observation is attributed to the varying degree of wettability, which culminates at 20 phr of zinc oxide content. For the shear strength, it increases steadily with zinc oxide loading, an observation that is associated to the steady increase in cohesive strength due to the interaction between the adhesive and the filler. The adhesion property increases with testing rate and coating thickness. J. VINYL ADDIT. TECHNOL., 22:3–7, 2016. © 2014 Society of Plastics Engineers     

Dependence of adhesion property of acrylonitrile‐butadiene rubber‐based adhesive on zinc oxide concentration

Viscosity and adhesion properties of acrylonitrile‐butadiene rubber (NBR)‐based pressure‐sensitive adhesive were investigated by using zinc oxide as the filler. The zinc oxide loading was varied from 10 to 50 parts by weight per hundred parts of rubber (phr). Coumarone–indene resin, toluene, and polyethylene terephthalate were used as the tackifying resin, solvent, and coating substrate, respectively. Viscosity of the adhesive was measured by a Brookfield viscometer, whereas the loop tack, peel strength, and shear strength were determined by a Lloyd adhesion tester operating at 10 to 60 cm/min. Results show that viscosity increases with zinc oxide loading because of the concentration effect. Loop tack and peel strength pass through a maximum value at 20 phr of zinc oxide concentration, whereas the optimum zinc oxide loading for shear strength is 30 phr. This observation is attributed to the effect of varying degrees of wettability and compatibility of the adhesive on the substrate. In all cases, the adhesion properties of adhesives increase with coating thickness and testing rates. J. VINYL ADDIT. TECHNOL., 23:241–246, 2017. © 2015 Society of Plastics Engineers     

Effect of zinc oxide on the viscosity,tack, and peel strength of ENR 25‐based pressure‐sensitive adhesives

Viscosity, loop tack, and peel strength of epoxidized natural rubber (ENR 25 grade)‐based pressure‐sensitive adhesive was studied in the presence of zinc oxide. The zinc oxide concentration was varied from 10–50 parts per hundred parts of rubber (phr). Coumarone–indene resin with loading from 20 to 100 phr was chosen as the tackifier resin. Toluene was used as the solvent throughout the experiment. The adhesive was coated on the substrate using a SHEEN hand coater to give a coating thickness of 60 μm. Viscosity of the adhesive was determined by a HAAKE Rotary Viscometer whereas the loop tack and peel strength were measured by a Llyod Adhesion Tester operating at 30 cm/min. Results show that viscosity and loop tack of adhesive increases with increasing zinc oxide concentration. For the peel strength, it increases with zinc oxide concentration up to 30–40 phr and drops after the maximum value. This observation is associated with the effect of varying degree of wettability of the adhesive on the substrate. However, for a fixed zinc oxide concentration, loop tack and peel strength exhibit maximum value at 80 phr resin loading after which both properties decrease with further addition of resin, an observation which is attributed to phase inversion. From this study, the optimum adhesion property is achieved by using 40 phr zinc oxide and 80 phr coumarone–indene resin. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Effect of N‐isopropyl‐N′‐phenyl‐p‐phenylenediamine antioxidant on the adhesion properties of (zinc oxide)‐filled (epoxidized natural rubber 25)‐based pressure‐sensitive adhesives

The effect of antioxidant, namely, N‐isopropyl‐N′‐phenyl‐p‐phenylenediamine (IPPD), on the adhesion properties of epoxidized natural rubber (ENR 25)‐based pressure‐sensitive adhesive was investigated. The concentration of the IPPD was varied from 0 to 5 parts by weight per hundred parts of rubber (phr). Coumarone‐indene resin, zinc oxide, toluene, and polyethylene terephthalate were used as the tackifier, filler, solvent, and substrate, respectively. A Lloyd Adhesion Tester operating at different testing rates (10–60 cm/min) was used to determine the loop tack, peel strength, and shear strength at 60‐µm and 120‐µm coating thicknesses. Results indicate that adhesion properties increase with IPPD up to 2 phr of content, after which it decreases with further addition of the antioxidant. This observation is attributed to the culmination of wettability and compatibility at the optimum IPPD concentration. The 60‐µm coated sample consistently shows higher adhesion strength than that of 120‐µm coated sample. Loop tack and peel strength increase with testing rate up to 30 cm/min. However, shear strength increases with increasing testing rate in the testing rate investigated in this study. J. VINYL ADDIT. TECHNOL., 21:111–115, 2015. © 2014 Society of Plastics Engineers     

Adhesion property of crosslinked epoxidized (natural rubber)/(acrylonitrile‐butadiene) rubber blend adhesives in the presence of petro resin tackifier

Loop tack, peel strength, shear strength, and morphology of (benzoyl peroxide)‐cured epoxidized natural rubber (ENR 25)/(acrylonitrile‐butadiene) rubber (NBR) blend adhesive were investigated by using petro resin as the tackifying resin. Benzoyl peroxide loading varied from 1 to 5 parts by weight per hundred parts of resin (phr), whereas the petro resin loading was fixed at 40 phr. A SHEEN hand coater was used to coat the adhesive on the polyethylene terephthalate substrate at 30 μm and 120 μm coating thicknesses. (ENR 25)/NBR adhesive was crosslinked at 80°C for 30 min prior to the determination of adhesion strength by a Lloyd adhesion tester operating at 10–60 cm/min. Results show that maximum loop tack and peel strength occur at 2 phr of benzoyl peroxide loading, whereby optimum cohesive and adhesive strength are obtained. However, shear strength increases with increasing benzoyl peroxide concentration, an observation that is associated with the steady increase in the cohesive strength. Scanning electron microscopy micrograph shows that little adhesive remained on the substrate at 0 phr compared with 2 phr of benzoyl peroxide loading, indicating that crosslinking increases the peel strength of the adhesive. In all cases, the adhesion properties increase with coating thickness and testing rate . J.VINYL ADDIT. TECHNOL., 24:93–98, 2018. © 2015 Society of Plastics Engineers     

Mechanical,thermal, and morphological properties of (eggshell powder)‐filled natural rubber latex foam

Eggshell (ES) waste is available in a huge quantity and has been listed worldwide as one of the worst environmental problems. This study aimed to use, for the first time, ES powder (ESP) as filler in natural rubber latex foam (NRLF). Tensile strength of NRLF incorporated with ESP initially drops at low ESP filler loading and then increases with the increment of filler loading from 5 to 10 parts by weight per hundred parts of resin (phr). As the ESP filler loading increases up to 10 phr, M100, compression stress, compression set, hardness, rubber filler interaction, and density increase. Meanwhile, elongation at break and recovery percentage of compression set decrease as the filler loading increases up to 10 phr. Field emission scanning electron microscopy results indicate that even at 10 phr of ESP loading, the fillers are homogenously dispersed in the matrix without agglomerations. However, the thermal stability of NRLF decreases with the incorporation of ESP, as indicated by results of thermogravimetric analysis. J. VINYL ADDIT. TECHNOL., 23:3–12, 2017. © 2015 Society of Plastics Engineers     

Adhesion behavior of natural rubber‐based adhesives crosslinked by benzoyl peroxide

The loop tack, peel, and shear strength of crosslinked natural rubber adhesive were studied using coumarone‐indene and toluene as the tackifying resin and solvent, respectively. The concentration of benzoyl peroxide‐the crosslinking agent—was varied from 1 to 4 parts per hundred parts of rubber (phr). A SHEEN hand coater was used to coat the adhesive on the polyethylene terephthalate substrate at various coating thickness. Loop tack, peel, and shear strength were measured by a Llyod adhesion tester operating at 30 cm min^?1. Result shows that loop tack and peel strength of the adhesive increases up to 2 phr of benzoyl peroxide concentration after which it decreases with further benzoyl peroxide content. This observation is attributed to the optimum crosslinking of natural rubber where optimum cohesive and adhesive strength occurs at 2 phr peroxide loading. However, for the shear strength, it increases with increasing benzoyl peroxide concentration where higher rate of increase is observed after 2 phr of peroxide content, an observation which is associated to the steady increase in cohesive strength of crosslinked rubber. In all cases, the adhesion properties of adhesives increase with increase in coating thickness. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

The Effect of Filler Loading and Epoxidation on Paper-Sludge-Filled Natural Rubber Composites

The effect of filler loading and epoxidation on curing characteristics, dynamic properties, tensile properties, morphology, and rubber-filler interactions of paper-sludge-filled natural rubber compounds have been studied. Two different types of natural rubber, SMR L and ENR 50, having 0% and 50% of epoxidation and conventional vulcanization were used. Paper sludge was used as a filler and the loading range was from 0 to 40 phr. Compounding was carried out using a laboratory-sized two-roll mill. The scorch time for both rubber compounds decreased with filler loading. The cure time was found to decrease with increasing filler content for SMR L vulcanizates, whereas for ENR 50, the cure time seemed to be independent of the filler loading. Dynamic properties, i.e., maximum elastic torque, viscous torque, and tan delta, increase with filler loading in both grades of natural rubber. Results also indicate that both rubbers show increment in tensile modulus but inverse trend for elongation at break and tensile strength. However, for a fixed filler loading, ENR 50 compounds consistently exhibit higher maximum torque, modulus at 100% elongation, and modulus at 300% elongation, but lower elongation at break than SMR L compounds. In the case of tensile strength, ENR 50 possesses higher tensile strength than SMR L at 10 to 20 phr, but the difference is quite small at 30 and 40 phr. These findings might be associated with better rubber-filler interaction between the polar hydroxyl group of cellulose fiber and the epoxy group of ENR 50.     

Dependence of Adhesion Properties of Cross-linked Epoxidized Natural Rubber (ENR 25)-Based Pressure-Sensitive Adhesives on Benzoyl Peroxide Loading in the Presence of Gum Rosin and Petroresin Tackifiers

The effect of benzoyl peroxide loading on the adhesion properties of cross-linked epoxidized natural rubber (ENR 25)-based adhesives was studied using gum rosin and petroresin as tackifiers. Toluene and polyethylene terephthalate (PET) were used as solvent and coating substrate, respectively. The adhesion properties were determined by a Lloyd adhesion tester operating at 30 cm min^?1. Results indicate that the loop tack and peel strength of gum rosin and petroresin pass through a maximum value at 2 parts per hundred parts of rubber (phr) and 3 phr benzoyl peroxide concentration, respectively, an observation which is attributed to the optimum cross-linking of ENR 25 where optimum, cohesive and adhesive strength is obtained. The shear strength, however, increases steadily with increasing benzoyl peroxide loading due to the steady increase in the cohesive strength. At the optimum benzoyl peroxide concentration, the petroresin-based adhesive consistently exhibits higher adhesion properties compared to that of gum rosin-based adhesives. The adhesion properties of both adhesive systems increase with increasing coating thickness.     

Adhesion Property of Benzoyl-Peroxide-Cured Epoxidized Natural Rubber/Acrylonitrile-Butadiene Rubber Blend Adhesives to Polyethylene Terephthalate Film

The loop tack, peel strength and shear strength of cross-linked epoxidized natural rubber (ENR-50)/acrylonitrile-butadiene rubber (NBR) blend adhesives were studied in the presence of coumarone-indene resin. Benzoyl peroxide was used as the cross-linking agent with dosage ranging from 1 to 5 parts per hundred rubber by weight (phr). Toluene was used as the solvent throughout the investigation. A SHEEN hand coater was used to coat the adhesive on a polyethylene terephthalate substrate at 60 and 120 μm coating thickness. The adhesive was cured at 80°C for 30 min prior to testing on a Lloyd adhesion tester operating at various testing rates from 10 to 60 cm min^?1. Results show that loop tack and peel strength of the ENR-50/NBR adhesives pass through a maximum value at 4 phr of benzoyl peroxide dosage. This observation is attributed to the increase in cohesive strength which culminates at 4 phr benzoyl peroxide loading. However, shear strength increases steadily with dosage of benzoyl peroxide due to the continuous increase in the cohesive strength as crosslinking of the rubber blend proceeds. In all cases, the adhesion properties increase with increasing coating thickness and testing rates.     

RHEOLOGICAL PROPERTIES OF ISOTACTIC POLYPROPYLENE/KAOLIN COMPOSITES

Rheological properties of isotactic polypropylene/kaolin composites have been evaluated at kaolin concentrations 0–17.4 vol% at 493K. The systems obeyed power-law model in shear stress–shear rate variations and were shear thinning, which increased with kaolin content. Apparent melt viscosity decreased up to 5% kaolin and increased with further increase in kaolin concentration. First normal stress difference increased up to 5 vol% kaolin and decreased beyond this kaolin content. Use of a titanate coupling agent modified the rheological properties through an enhanced bonding between the filler and the polymer.     

Properties of Ferrite-Filled Natural Rubber Composites

Nickel zinc ferrite (Ni-ZnFe₂O₄)-filled natural rubber (NR) composite was prepared at various loading of ferrite. The tensile properties included in this study were tensile strength, tensile modulus and elongation at break. The tensile strength and elongation at break of the composites increased up to 40 parts per hundred rubber (phr) of ferrite and then decreased at higher loading whereas the tensile modulus was increased gradually with increasing of ferrite loading. Scanning electron microscopy (SEM) was used to determine the wettability of filler in rubber matrix. From the observation, the increase of filler loading reduced the wettability of the filler. Thermal stability of the composites was conducted by using a thermogravimetry analyser (TGA). The incorporation of ferrite in NR composites enhanced the thermal stability of NR composites. The swelling test results indicate that the swelling percentage of the composites decreased by increasing of ferrite loading. The initial permeability, μ_i and quality factor, Q of magnetic properties of NR composites achieved maximum value at 60 phr of ferrite loading for frequency range between 5000–40,000 kHz. The maximum impedance, Z _max of the NR composites was at the highest value at 80 phr ferrite loading for frequency range between 200–800 MHz.     

Tack and Shear Strength of Adhesives Prepared from Styrene-Butadiene Rubber (SBR) Using Gum Rosin and Petro Resin as Tackifiers

Tack and shear strength of styrene-butadiene rubber (SBR)-based pressure-sensitive adhesive were studied using gum rosin and petro resin as the tackifiers. The concentration of the tackifying resin was varied from 0 to 100 parts per hundred parts of rubber (phr). Toluene was used as the solvent throughout the experiment. The rolling ball technique was used to measure the tack of the adhesive, whereas, shear strength was determined by a TA-HDi Texture Analyser. Results show that the tack of the adhesive increases with increasing tackifier loadings for both tackifier systems. However, shear strength indicates the reverse behavior with increasing resin content, an observation which is attributed to the decrease in cohesive strength as the tackifier concentration is increased. Both tack and shear strength of the adhesives increases with molecular weight of SBR. Adhesive containing petro resin consistently exhibits higher values than the gum rosin system due to better wettability and compatibility in the former system.