New main chain nonlinear optical polymers with high glass transition temperatures

Summary Various 4-methoxy-4-carbomethoxy--amino--cyanostilbenes were prepared as mixtures of E and Z isomers, and polymerized via condensation polymerization using dibutyltin diacetate as catalyst. The resulting low molecular weight homopolymers showed higher glass transition temperatures (168–183°C) than previously reported main chain nonlinear optical (NLO) homopolymers. A high molecular weight (M_n30, 200) copolymer possessed an even higher glass transition temperature of 187°C. The hyperpolarizability of the polymers and a model compound were found by EFISH measurements to be in the range of 61 to 79x10^-48 esu.     

Hydrodynamic effects on the efficiency of porous flow-through electrodes

Hydrodynamic conditions in porous flow-through electrodes are discussed with special emphasis on radial diffusion effects on the efficiency of reactant conversion. The effect of porosity and tortuosity on the conversion efficiency are also considered. It is shown experimentally that radial diffusion limits the electrode efficiency for(L)=vr ²/2DL>0.5 and normal porosity and tortuosity values; q1. For(L)<0.5, the electrode works with 100% efficiency.A porous flow-through electrode is divided, in the most general case, into three regions: (a) velocity entrance length h0.2vr²/v in which a steady velocity profile is developing; (b) diffusional entrance lengthHvr ²/2D for which(x)=vr ²/2Dx1; in this region a radial diffusional concentration profile is developing andh is usually much smaller thanH; (c) the region where the velocity and concentration profiles are fully developed. Only in region (c) does the electrode operate with 100% efficiency. In regions (a) and (b) radial diffusion limits the electrode efficiency.     

Spalling Kinetics over a Wide Range of Shock-Wave Amplitude and Duration

The paper reports results of metallographic studies of specimens of St. 3 steel and M1 copper loaded by shock waves of various intensity (p 2 – 30 GPa) and duration ( 10^–6 – 10^–7 sec). The kinetics of spalling fracture of materials under these conditions is discussed. Key words: metals, shock waves, fracture, kinetics, modeling.     

Specific features of the phase transformations occurring during the sintering process of the beta-alumina based ceramics and their properties

Conclusions During the sintering process of beta-alumina obtained using the method of plasmochemical synthesis, the structural transformation occurs and it is accompanied by the separation of the excess Na₂O and the formation of an intergranular meltlike phase that is saturated with sodium and is characterized by high dielectric properties.The quantity of the meltlike phase and the magnitude of the /( + ) ratio determine the degree of stabilization (stability) and the final resistivity of the material and depend on the initial chemical composition and the heating rate maintained during the sintering process.It was shown that when the duration of residence of the material in the hot zone of the furnace is increased or when the specimens sintered maintaining high heating rates are subjected to additional heat treatment, one observes the occurrance of the reverse structural transformation that is characterized by an increase of the phase ratio /( + ) 1, a reduction in the quantity of the meltlike phase right up to its complete disappearance, and a decrease of the electrical resistivity of the material.In the materials having a large excess quantity of sodium oxide, the process of crystallization of the intergranular NaAlO₂ phase occurs simultaneously with the second phase transformation.The best ceramic and electrophysical parameters were obtained when sintering the material contained 7.9% Na₂O.Translated from Ogneupory, No. 3, pp. 13–18, March, 1990.     

Cooperative inclusion of sodium 1-pyrenesulfonate by γ-cyclodextrin

Summary The interaction of -cyclodextrin(-CD) with sodium 1-pyrenesulfonate(PS) was studied spectrophotometrically. -CD was found to cause much larger decrease in the absorption maxima of PS than -CD. The fluorescence spectra of PS in the presence of -CD showed excimer emission, while those of PS with -CD showed only monomer emission, indicating that -CD forms 12 (-CDPS) complexes in which two PS molecules are included in the -CD cavity in a face-to-face fashion. The binding isotherm showed a sigmoidal curve. The association constants were estimated by computer simulation of the binding curve. The 12 (CDPS) complex was found to be much more stable (K=10⁶ M^–1) than the 11 complex (K=1 M^–1). At high concentration of -CD another -CD cooperates in binding two PS molecules, resulting in the formation of a 22 complex.     

Molybdenum nitride for the direct decomposition of NO

The physico-chemical properties of passivated -Mo₂N have been investigated. The material showed high activities for NO direct decomposition: nearly 100% NO conversion and 95% N₂ selectivity were achieved at 450C. The amount of O₂ taken up by -Mo₂N increased with temperature rise and reached 3133.9 molg^–1 at 450C; we conclude that there formation of Mo₂O_xN_y occurred. This oxygen-saturated -Mo₂N material was catalytically active: NO conversion and N₂ selectivity were 89 and 92% at 450C. We found that by means of H₂ reduction at 450C, Mo₂O_xN_y could be reduced back to -Mo₂N and the oxidation/reduction cycle is repeatable; such a behaviour and the high oxygen capacity (3133.9 molg^–1) of -Mo₂N suggest that -Mo₂N is a promising catalytic material for automobile exhaust purification.     

Properties ofSrMO 3-δ(M=Fe,Co) as oxygen electrodes in alkaline solution

Strontium ferrates and cobaltates with compositions SrFeO_3- (0.060.40) and SrCoO_3- (0.040.30) were synthesized. The dependence of the oxygen electrode properties on the value was examined in 1 mol dm^–3 KOH solution. In the SrFeO_3- series, the samples with 0.24<<0.29, showed the highest activity in both oxygen evolution and reduction reactions. In contrast, no strong dependence on the value was observed in SrCoO_3-, which also showed a high catalytic activity for oxygen evolution.     

Nucleation and growth kinetics of Ag7NO11 on a platinum single crystal electrode

The process of electrochemical deposition of Ag₇NO₁₁ on a platinum single crystal anode from 5M AgNO₃ is investigated. The nucleation and growth rates are measured at different constant overpotentials. The orientation of the Ag₇NO₁₁ crystals with respect to the substrate surface is determined in the case of deposition on glassy carbon and on the 100, 111 and 110 faces of a platinum single crystal.     

Structure of the Reaction Zone of a Steady Detonation Wave in Dinitrodiazapentane

The massvelocity profiles in 2,4dinitro2,4diazapentane samples of different densities were registered by a laser interferometer and the electromagnetic technique. The reaction time was shown to reach 300 nsec and weakly depend on density, while the pressure in the chemical spike can be twice as high as that at the Chapman–Jouguet point. No special features due to diamond formation were observed in the massvelocity profiles registered in the chemical reaction zone.     

Postinduction Processes During Thermal Explosion in the Systems “Porous Material–Reactive Gas–Solid Product”

A complete solution of the unsteadystate filtration problem of thermal explosion incorporating the postinduction period is given for the first time. The paper describes a study of the temperaturefield dynamics, poregas pressure, and the degree of condensedphase conversion versus the reactivegas deficiency in a reactive porous material. Focus is on the formation and propagation of frontal regimes of exothermic chemical reactions (their number, direction, and velocity of propagation, degree of condensedphase conversion at the front). The study revealed double selfignition phenomena and combustionwave propagation regimes with incomplete conversion at the front. A surface regime of thermal explosion limited by gas filtration from the outside was considered. The regularities in the dynamics of the exothermic chemical reaction found in the present study allow one to qualitatively control hightemperature synthesis under thermal explosion conditions.     

Heterogeneous asymmetric reactions. 23. Enantioselective hydrogenation of ethyl pyruvate over cinchonine- and α-isocinchonine-modified platinum catalysts

The enantioselective hydrogenation of ethyl pyruvate to (S)-ethyl lactate over cinchonine- and -isocinchonine-modified Pt/Al₂O₃ catalysts was studied as a function of modifier concentration and reaction temperature. The maximum enantioselectivities obtained under the applied mild conditions were 89% ee using cinchonine (0.014 mmoldm^–3, 1 bar H₂, 23°C, 6% AcOH in toluene), and 76% ee in the case of -isocinchonine (0.14 mmoldm^–3, 1 bar H₂, –10°C, 6% AcOH in toluene). Since -isocinchonine of rigid structure exists only in anti-open conformation these data provide additional experimental evidence to support the former suggestion concerning the dominating role of anti-open conformation in these cinchona-modified enantioselective hydrogenations.     

Experimental Study of the Disperse Composition of Condensed Products of Aluminum‐Particle Combustion in Air

The particle shape and structure and also the disperse composition of condensed products of combustion of ASD1, ASD4 and ASD6 aluminumbased powders in air with oxidizertofuel ratios of 0.12–0.4 and initial pressures of 0.05–0.30 MPa are examined. The mass of submicron particles of aluminum oxide amounts to 90% of the total mass of condensed combustion products. The mean mass diameter of particles is 0.15–0.18 m and increases with increasing pressure. Under atmospheric pressure, the initial disperse composition of aluminum powders and the proportion between the components in the combustor volume have little or no effect on the disperse composition of the condensed phase. A comparative analysis is performed of the disperse composition of condensed phase particles formed due to aluminum combustion in various propellant mixtures and various combustors. It is shown that the main factors affecting the disperse composition are the type of the propellant mixture, the gasdynamic combustion process, and the conditions determining the interaction of aluminum particles with each other and with the gas phase.     

Stereoisomers composition of 4-[(1′-methylpropyl)-oxycarbonyl]-2-oxetanone and related compounds,as precursors of fuctional polyesters,determined by chiral gas chromatography

Summary The configurational analysis of racemic and optically active stereoisomers of 4-[(1-methylpropyl)oxycarbonyl]-2-oxetanone has been carried out by using chiral gas chromatography. This technique has been successful in the stereoisomers composition determination of these -substituted -lactones prepared by two different routes and used as monomers in the preparation of malic acid stereocopolymers. Result are in good agreement with those obtained from high resolution ¹H NMR, in the presence of an Europium salt, as chiral shift reagent. This method has been extended to 3-methyl-4-[(1,2,2-trimethyl propyl)oxycarbonyl]-2-oxetanone. The exact knowledge of precursors configurational structure is very important in regard to the obtention of the corresponding polystereoisomers with a strictly controlled enantiomeric or diastereoisomeric composition and consequently with predictable properties.     

Synthesis, Characterization and Optimum Reaction Conditions of Oligo-N, N′-bis (2-hydroxy-1-naphthalidene) Thiosemicarbazone

The oxidative polycondenzation reaction conditions of N, N-bis (2-hydroxy-1-naphthalidene) thiosemicarbazone (HNTSC) using air oxygen, H₂O₂ and NaOCl were studied in an aqueous alkaline medium between 50–90°C. Oligo-N, N-bis (2-hydroxy-1-naphthalidene) thiosemicarbazone was characterized by ¹H-NMR, FT-IR, UV-Vis, size exclusion chromatography (SEC) and elemental analysis techniques. Solubility testing of oligomer was investigated using organic solvents such as DMF, THF, DMSO, methanol, ethanol, CHCl₃, CCl₄, toluene acetonitrile, ethyl acetate, concentrated H₂SO₄ and an aqueous alkaline solution. Using NaOCl, H₂O₂ and air O₂ oxidants, conversion to oligo-N, N-bis (2-hydroxy-1-naphthalidene) thiosemicarbazone (OHNTSC) of N, N-bis (2-hydroxy-1-naphthalidene) thiosemicarbazone was found to be 85, 80 and 76%, respectively, in an aqueous alkaline medium. According to the SEC analyses, the number-average molecular weight, weight-average molecular weight and polydispersity index values of OHNTSC synthesized were found to be 1050 gmol^–1 1715 gmol^–1 and 1.63, using NaOCl, and 2137, 2957 gmol^–1 and 1.38, using air O₂ and 2155 gmol^–1 4164 gmol^–1 and 1.93, using air H₂O₂, respectively. Also, TG analysis was shown to be unstable of oligo-N, N-bis (2-hydroxy-1-naphthalidene) thiosemicarbazone against thermo-oxidative decomposition. The weight loss of OHNTSC was found to be 97.29% at 900°C.     

The role of Ni2+ diffusion on the reducibility of NiO/MgO system: A combined TRP-XPS study

The progressive dissolution of nickel ions in the lattice of MgO matrix, promoted by the calcination temperature, has been monitored using XPS. The reducibility of Ni/MgO catalysts is affected by the modification of the surface chemical composition. TPR peaks have been correlated with several NiO forms. Both XPS and TPR results indicate a different behaviour pattern for the supported and physically mixed NiO/MgO systems, and this has been attributed to the different available contact area between NiO and MgO. The formation of both NiO rich and MgO rich NiO-MgO solid solutions, with the tendency to evolve towards the bulk solid solution, has been invoked to explain the substantial changes in the TPR pattern of the different air calcined systems.     

Soldier defense secretions of malaysian free-ranging termite of the genusLacessititermes (Isoptera,Nasutitermitinae)

Soldiers of free-ranging termites of the genusLacessititermes (Isoptera, Nasutitermitinae) secrete from their frontal glands a mixture of monoterpenes, sesquiterpenes, and diterpenes.Lacessititermes ransoneti, L. laborator, andL. species A produce species-specific secretions, the composition being most complex forL. laborator. Apart from known mono- and dihydroxytrinervitadienes, the following new diterpenes were isolated and tentatively assigned as trinervita-1(15),8(19)-dien-2,3,9,14-tetraol 2,3,14-O-triacetate, trinervita-1(15),8(19)-dien-2,3,9,14-tetraol 2,3,14-O-triacetate, 2,3,9, 14-tetraacetoxy-1 (15), 8(19)-trinervitadiene, and 2,3,11,13-tetraacetoxy-1(15),8(19)-trinervitadiene. Data on intragenus chemical variations were subjected to canonical discriminant analysis and genetic distances among the species were calculated to depict intragenus identities and affinities.     

Crystal structure and morphology of electrodeposited zinc-iron binary alloys

Deposits of zinc-iron alloy have been prepared galvanostatically from a sulphate bath and the crystal structure has been determined by X-ray diffraction and transmission electron microscopy measurements. The electrodeposited zinc-iron alloys have metastable structures and the individual phases coexist over wide composition ranges. The phases are identified as (10073 at % zinc), (8748 at % zinc), ₁(7862 at % zinc) and (620 at % zinc). Thec andc/a in the h.c.p. lattice of the -phase decrease continuously with decrease of zinc concentrations, and the latter changes from 1.86 to 1.60 (a andc are the lattice constants of the -phase in the direction of thea- andc-axes, respectively). The -phase particles exhibit a hexagonal plate-like morphology which is thin in the direction of thec-axis. The morphology of the electrodeposits changes from plate-like to pyramidal shape when fine -phase particles (100 nm) start to form surrounding the -phase platelets, and then to lenticular or granular in the /₁ duplex region. The -phase forms in the low zinc concentration region and changes the electrodeposits to a fine cuboidal morphology.     

Change in degree of polyamidation of polycaproamide during orientation stretch

Conclusions The effect of stretch ratio, the ratio of stretch ratios in the cold and hot zones, and of the relative viscosity of polycaproamide on the degree of its breakdown during stretching have been examined.The degree of breakdown decreases if the viscosity stays within the range 3.25–3.35, and the stretch ratio in the cold zone is the maximum possible.Translated from Khimicheskie Volokna, No. 5, pp. 26–27, September–October, 1983.     

On the structure of the activated iron catalyst for ammonia synthesis

The contribution focuses on a brief account of the activation of iron oxide precursors to ammonia synthesis catalysts and discusses the question as to why normal iron is so inferior in catalytic performance compared to ammonia iron. The combination of microstructural analysis with kinetic observations allows the conclusion that the microtexture of ammonia iron is with a platelet morphology different from isotropic iron. The role of all additives in the generation of the platelet form is examined. The presence of oxygen, which was speculated to be beneficial for the reaction under certain conditions, was found to be detrimental for the catalytic performance under the present testing conditions.     

Lamellar Thickness of a Syndiotactic Polystyrene Determined from Small-angle X-ray Scattering and Transmission Electron Microscopy

Extensive morphological studies on a syndiotactic polystyrene (sPS) sample prepared from compression molding were carried out using small-angle X-ray scattering (SAXS) and transmission electron microscopy (TEM). SAXS was conducted at 25C as well as at 150C to enhance the scattering contrast in order to obtain more reliable morphological parameters. The compression-molded sample was crystallized into a orthorhombic crystal lattice characterized by wide-angle X-ray diffraction (WAXD). A similar weight fraction of crystallinity, ca. 0.37, was obtained from both WAXD and differential scanning calorimetry measurements.In addition to the scattering peak at a scattering vector of ca. 0.36 nm^–1 attributable to the presence of lamellar/amorphous layers, anomalous scattering at the zero angle was found from the SAXS intensity profiles. Based on the Debye–Bueche theory, the scattering profile of this peculiar zero-angle scattering was deduced and was subtracted from the raw intensity profile to obtain the intensity profile exclusively associated with the lamellar/amorphous structure. A consistent long period was obtained for SAXS measured either at 25 or 150C, provided that the appropriate subtraction of intensities due to the zero-angle scattering was conducted. Moreover, the lamellar thickness deduced from the one-dimensional correlation function was in good agreement with TEM results. A difference scattering pattern derived from SAXS measured at 150 and 25C was obtained and a comparison of the morphological parameters was provided as well.