Aqueous slip casting and hydrolysis assisted solidification of MgAl2O4 spinel ceramics

Abstract

Abstract

This paper reports on synthesis of MgAl₂O₄ spinel (MAS) powders with six different chemical compositions and the consolidation of the synthesised MAS powders following an aqueous slip casting and hydrolysis assisted solidification (HAS) routes. The synthesised MAS powders were surface passivated against hydrolysis before being dispersed in distilled water to obtain suspensions with 41–45?vol.‐% solid loading using suitable dispersing agents. In the case of the HAS process, the consolidation of suspensions was achieved in non‐porous moulds under ambient conditions by the incorporation of AlN equivalent to 1–5?wt‐%Al₂O₃ into the suspension. The stoichiometric MAS powder consolidated by slip casting and dry pressing routes was sintered along with those consolidated by HAS route at 1550–1650°C for 1?h. Various characterisation techniques were utilised to evaluate the effect of composition and consolidation technique on slurry characteristics and sintered properties of MAS ceramics.     

Co-precipitated ZnAl2O4 spinel precursor as potential sintering aid for pure alumina system

Ultra-fine ZnAl₂O₄ spinel hydrogel precursor synthesized from mixed salt solutions of Zn²⁺ and Al³⁺ ions using ammonium hydroxide–hexamethylenetetramine as basic media for co-precipitation was used as bonding material and sintering aid for pure alumina system. The hydrogel powder exhibited some well-defined ZnAl₂O₄ spinel phases at 800 °C. Alumina compacts were fabricated by incorporating small proportions of the precursor in alumina powder and firing at different temperatures (1350–1500 °C). The degree of densification was studied by measurement of fired shrinkage, apparent porosity, bulk density and cold crushing strength. Phase compositions and microstructural features of sintered samples were evaluated by XRD and SEM respectively. Addition of 0.2% hydrogel powder to alumina exhibited remarkable influence on development of high mechanical strength. The in situ formed ZnAl₂O₄ spinel dopant acted as a grain growth inhibitor in the alumina system.     

Alumina/MWCNTs composites by aqueous slip casting and pressureless sintering

Slip casting of stabilized aqueous suspensions followed by pressureless sintering was used for preparation of dense Al₂O₃/MWCNTs composites. The suspensions were stabilized by commercial polyelectrolyte dispersant Darvan C–N. In order to increase the stability, the pH value of the suspension was adjusted to ∼10. At this pH the highest ζ-potential values of the alumina powder and of the MWCNTs functionalised in boiling nitric acid were achieved. Two different agents, namely ammonium hydroxide and sodium hydroxide, were used for the pH adjustment. Their influence on the viscosity of suspensions and on consolidation and densification behaviour of the Al₂O₃/MWCNT composites was evaluated. The effect of ammonium hydroxide was more pronounced, as confirmed by lower viscosity of the suspension, higher sintered density, and fine-grained microstructure of the sintered composites. The Al₂O₃/t-MWCNTs composites with 0.1 wt% of the MWCNTs, with 99.9% relative density, the mean size of alumina grains ∼1 μm, and homogeneously distributed carbon nanotubes were prepared by the pressureless sintering at 1500 °C.     

Densification ability of combustion-derived Al2O3 powders

Nanocrystalline Al₂O₃ powders containing different amounts of MgO (0.1–5.0 mol%) or added boehmite (AlOOH) have been synthesized by combustion synthesis from aluminium nitrate and magnesium nitrate, using urea or sucrose as fuels. The as synthesized alumina powders were deagglomerated, compacted by dry pressing and sintered at 1625 °C for 2 h. For comparison purposes, a commercial high purity α-Al₂O₃ powder (ACC) was also processed following the same route. The sintered materials were characterized for bulk density (BD), apparent porosity (AP), and water absorption (WA) capacity, microstructure using SEM, and XRD phase composition. In comparison to boehmite, the MgO had a considerable effect on the densification behaviour of combustion-synthesized powder.     

Laser stereolithography of ZrO2 toughened Al2O3

Ceramic laser stereolithography is a manufacturing process suitable candidate for the production of complex shape technical ceramics. The green ceramic is produced layer by layer through laser polymerisation of UV curable ceramic suspensions. A number of critical issues deserve attention: high solid loading and low viscosity of the suspensions, high UV reactivity, prevention of interlayer delamination in the green and in the sintered body, good mechanical performance. In this work, ZrO₂-reinforced Al₂O₃ components have been obtained from an acrylic modified zircon loaded with alumina powders. The zircon compound is effective as organic photoactivated resin and allows the dispersion of a high volume fraction of Al₂O₃ powder (up to 50 vol.%) while keeping viscosity at reasonable low values. The zircon compound also represents a liquid ceramic precursor that converts to oxide after burning out of the binder. Thank to the good dispersion of the alumina powder in the zircon acrylate, a uniform dispersion of ZrO₂ submicron particles is obtained after pyrolysis. These are located at the grain boundaries between alumina grains. Formation of both monoclinic and tetragonal ZrO₂ occurs as evidenced by XRD. No delamination occurs in bending tests as evidenced by SEM fractography, satisfactory modulus and strength values were concurrently found.     

Low temperature solid-state synthesis routine and mechanism for Li3V2(PO4)3 using LiF as lithium precursor

Monoclinic lithium vanadium phosphate, Li₃V₂(PO₄)₃, has been successfully synthesized using LiF as lithium source. The one-step reaction with stoichiometric composition and relative lower sintering temperature (700 °C) has been used in our experimental processes. The solid-state reaction mechanism using LiF as lithium precursor has been studied by X-ray diffraction and Fourier transform infrared spectra. The Rietveld refinement results show that in our product sintered at 700 °C no impurity phases of VPO₄, Li₅V(PO₄)₂F₂, or LiVPO₄F can be detected. The solid-state reaction using Li₂CO₃ as Li-precursor has also been carried out for comparison. X-ray diffraction patterns indicate that impurities as Li₃PO₄ can be found in the product using Li₂CO₃ as Li-precursor unless the sintering temperatures are higher than 850 °C. An abrupt particle growth (about 2 μm) has also been observed by scanning electron microscope for the samples sintered at higher temperatures, which can result in a poor cycle performance. The product obtained using LiF as Li-precursor with the uniform flake-like particles and smaller particle size (about 300 nm) exhibits the better performance. At the 50th cycle, the reversible specific capacities for Li₃V₂(PO₄)₃ measured between 3 and 4.8 V at 1C rate are found to approach 147.1 mAh/g (93.8% of initial capacity). The specific capacity of 123.6 mAh/g can even be hold between 3 and 4.8 V at 5C rate.     

Creep behaviour of alumina/YAG composites prepared by different sintering routes

Al₂O₃-5 vol.% Y₃Al₅O₁₂ (YAG) composite powders have been prepared by surface doping of α-alumina powders by an yttrium chloride aqueous solution. Two commercial, one submicron-sized, the other ultra-fine, alumina powders were compared as matrix materials. YAG phase was yielded by an in situ reaction promoted by the subsequent thermal treatment of the doped powders. In particular, a flash soaking into a tubular furnace kept at a fixed temperature in the range 1050-1150 °C was employed, for inducing the crystallization of yttrium-aluminates on the alumina particles surface, but avoiding a relevant crystallites growth. After that, aqueous suspensions of the calcined powders were dispersed by ball-milling and cast into porous moulds or simply dried in a oven. Slip cast green bodies were densified by pressure-less sintering, while powdered samples were consolidated by hot pressing or spark plasma sintering. The low- and high-temperature mechanical performances of the sintered materials were investigated and related to monolithic aluminas behaviour as well as to the composites microstructures. It is shown that the hot-pressed and spark plasma sintered composites present a significantly lower creep rate as compared to reference, monolithic alumina samples.     

Alumina/silicon carbide composites fabricated via in situ synthesis of nano-sized SiC particles

Alumina/silicon carbide composites have been fabricated by a new technique involving the in situ synthesis of nano-sized SiC particles. A mixture of alumina powder and silicon carbide precursors was prepared in an aqueous suspension. Green bodies were formed by cold isostatic pressing of granules obtained by freeze granulation, and pressureless sintered at 1750 °C for 4 h in an argon atmosphere. Mullite (10–20 vol%) formed in addition to SiC during sintering. The SiC particles were located predominantly to the interior of the mullite and alumina matrix grains.     

Phase and microstructural evolution of yttrium-doped nanocrystalline alumina: A contribution of advanced microscopy techniques

Well-dispersed nano-crystalline transition alumina suspensions were mixed with yttrium chloride aqueous solutions, with the aim of producing Al₂O₃-Y₃Al₅O₁₂ (YAG) composite powders. DTA analysis allowed to highlight the role of yttrium on the α-phase crystallization path. Systematic XRD and HRTEM analyses were carried out in parallel on powders calcined in a wide temperature range (600-1300 °C) in order to follow phase and microstructural evolution. A thin, homogeneous yttrium-rich layer was yielded on the alumina particles surface; yttrium diffusion into the alumina matrix was negligible up to 1150 °C whereas, starting from 1200 °C, aggregates of partially sintered alumina particles appeared, stuck together by yttrium-rich thin films. Moreover, in the yttrium-richer zones, such as alumina grain boundaries and triple joints, yttrium-aluminates precipitated at alumina particles surface. Finally, at 1300 °C, alumina-YAG composite powders were produced, in which YAG was homogenously distributed among the alumina grains.     

Sintering of glass-added BaZn1/3Nb2/3O3 ceramics

The complex perovskite oxide Ba(Zn_1/3Nb_2/3)O₃ (BZN) has been studied for its attractive dielectric properties which place this material interesting for applications as multilayer ceramics capacitors or hyperfrequency resonators. This material is sinterable at low temperature with combined glass phase–lithium salt additions, and exhibits, at 1 MHz very low dielectric losses combined with relatively high dielectric constant and a good stability of this later versus temperature. The 2 wt.% of ZnO–SiO₂–B₂O₃ glass phase and 1 wt.% of LiF-added BZN sample sintered at 900 °C exhibits a relative density higher than 95% and attractive dielectric properties: a dielectric constant ?_r of 39, low dielectrics losses (tan(δ) < 10⁻³) and a temperature coefficient of permittivity τ_? of 45 ppm/°C⁻¹. The 2 wt.% ZnO–SiO₂–B₂O₃ glass phase and 1 wt.% of B₂O₃-added BZN sintered at 930 °C exhibits also attractive dielectric properties (?_r = 38, tan(δ) < 10⁻³) and it is more interesting in terms of temperature coefficient of the permittivity (τ_? = −5 ppm/°C). Their good dielectric properties and their compatibility with Ag electrodes, make these ceramics suitable for L.T.C.C applications.     

The production of advanced fine-grained alumina by carbon nanotube addition

Alumina and alumina + 1 vol.% carbon nanotube (CNT) composites were fully densified by spark plasma sintering. Post-sintering heat treatments (1300–1500 °C) were performed to completely oxidize CNTs and then densify the remaining 1 vol.% to produce fine-grained ceramics. The grain size and Vickers hardness of the heat-treated composites were compared with the monolithic alumina sintered without CNT addition. Compared to the initial powder particle size of alumina (D₅₀: 356 ± 74 nm), minimal grain growth (∼450 nm) was observed for the fully dense heat-treated composites. A 25% improvement in Vickers hardness and >10 times finer average grain size were observed for alumina produced by the heat treatment (1300 °C) of alumina + 1 vol.% CNT composite, compared to alumina sintered without CNTs.     

Synthesis and characterization of MgAl2O4–ZrO2 composites

Different types of dense 5–97% ZrO₂–MgAl₂O₄ composites have been prepared using a MgAl₂O₄ spinel obtained by calcining a stoichiometric mixture of aluminium tri-hydroxide and caustic MgO at 1300 °C for 1 h, and a commercial yttria partially stabilized zirconia (YPSZ) powder as starting raw materials by sintering at various temperatures ranging from 1500 to 1650 °C for 2 h. The characteristics of the MgAl₂O₄ spinel, the YPSZ powder and the various sintered products were determined by X-ray diffraction (XRD), scanning electron microscopy (SEM), BET surface area, particle size analysis, Archimedes principle, and Vickers indentation method. Characterization results revealed that the YPSZ addition increases the sintering ability, fracture toughness and hardness of MgAl₂O₄ spinel, whereas, the MgAl₂O₄ spinel hampered the sintering ability of YPSZ when sintered at elevated temperatures. A 20-wt.% YPSZ was found to be sufficient to increase the hardness and fracture toughness of MgAl₂O₄ spinel from 406 to 1314 Hv and 2.5 to 3.45 MPa m^1/2, respectively, when sintered at 1600 °C for 2 h.     

Synthesis of Bi0.5(Na0.7K0.2Li0.1)0.5TiO3 powders through the molten salt method

The Bi_0.5(Na_0.7K_0.2Li_0.1)_0.5TiO₃ powder synthesis through molten salt method was investigated in the temperature range of 650–700 °C for 2–4 h. The XRD results indicated that the optimal synthesizing temperature for molten salt method was 700 °C, significantly lower than that for conventional processing route of solid state reaction method, where a calcining temperature of 850 °C was needed. The SEM results revealed better crystallization of the powders obtained through molten salt method, compared with those through the conventional processing route of solid state reaction method.     

Electrochemical properties of nanostructured Li1.2V3O8 in aqueous LiNO3 solution

The amorphous hydrated precursor of Li_1.2V₃O₈ was synthesized by soft chemistry method, and then heat-treated in air at several temperatures within the range 200–400 °C. The heat-treatment changed its morphological, structural and charging/discharging performance. The product obtained upon the treatment at 300 °C, consisting of uniform, rod-shaped particles, 100–150 nm in diameter and 300–800 nm in length, displayed the best electrochemical performance in aqueous LiNO₃ solution. Its initial discharge capacity amounted to 136.8 mAh g⁻¹ at a rate of C/5, which upon 50 charging/discharging cycles decreased for only 12%.     

Influence of processing route on microstructure and mechanical properties of MgAl2O4 spinel

This paper reports on process dependant microstructural and mechanical properties of MgAl₂O₄ spinel (MAS) ceramics. Two MAS powders with different chemical compositions were synthesized by solid-state reaction of alumina and calcined caustic magnesia at 1400 °C for 1 h. The surface of the as obtained MAS powders was passivated against hydrolysis by coating it with H₃PO₄ and Al(H₂PO₄)₃ species dissolved in ethanol at 80 °C for 24 h. The as protected powders could then be dispersed in aqueous solutions of tetramethylammonium hydroxide (TMAH) and Duramax D-3005 as dispersing agents to obtain stable slurries with 45 vol.% solids loading. The stable aqueous MAS slurries were consolidated by slip casting (SC), gelcasting (GC), hydrolysis assisted solidification (HAS) and hydrolysis induced aqueous gelcasting (GCHAS) routes, fully dried and then sintered for 1 h at 1650 °C. For comparison purposes, dense MAS ceramics were also prepared following a conventional dry-powder pressing (DP) and temperature induced gelation (TIG) routes. All the sintered MAS ceramics were thoroughly characterized for bulk density, apparent porosity, water absorption capacity, SEM microstructure, XRD phase, hardness, 3-point bend strength, and percentage of shrinkage to evaluate the suitability of the processing routes for fabricating defect free components with near-net shape. Among the various techniques employed, the GCHAS was found to be best for fabricating near-net shape MAS ceramics.     

Synthesis and sintering behavior of La0.8Sr0.2CrO3 by a glycine nitrate process

La_0.8Sr_0.2CrO₃ powder was synthesized by a glycine nitrate process from an aqueous solution of lanthanum, strontium, and chromium nitrates, and glycine. The apparent density, size and morphology of the La_0.8Sr_0.2CrO₃ powder depended on the glycine-to-nitrate ratio. However, the pH value of the precursor solution had no significant effect on these properties. It was found that a single-phase perovskite, La_0.8Sr_0.2CrO₃, was synthesized when the dried ash was calcined at 1200 °C for 5 h. A secondary minor phase, SrCrO₄, was observed in the powder calcined at temperatures lower than 1100 °C. The presence of the SrCrO₄ phase has a significant effect on the sinterability and microstructural evolution of the La_0.8Sr_0.2CrO₃. A relative density higher than 90% could be achieved when the 1000 °C-calcined La_0.8Sr_0.2CrO₃ powder was sintered at 1450 °C.     

Synthesis and properties of (BaxPb1−x)(Zn1/3Nb2/3)O3 relaxor ferroelectric ceramics using a reaction-sintering process

(Ba_xPb_1−x)(Zn_1/3Nb_2/3)O₃ (BPZN; x = 0.06–0.1) relaxor ferroelectric ceramics produced using a reaction-sintering process were investigated. Without any calcination involved, the mixture of raw materials was pressed and sintered directly. BPZN ceramics of 100% perovskite phase were obtained. Highly dense BPZN ceramics with a density higher than 98.5% of theoretical density could be obtained. Maximum dielectric constant K_max 13,500 (at 75 °C), 19,600 (at 50 °C) and 14,800 (at 28 °C) at 1 kHz could be obtained in 6BPZN, 8BPZN and 10BPZN, respectively. Dielectric maximum temperature (T_max) in BPZN ceramics via reaction-sintering process is lower than BPZN ceramics prepared via B-site precursor route.     

Microwave dielectric properties of SnO2-doped CaSiO3 ceramics

SnO₂-doped CaSiO₃ ceramics were successfully synthesized by a solid-state method. Effects of different SnO₂ additions on the sintering behavior, microstructure and dielectric properties of Ca(Sn_1−xSi_x)O₃ (x=0.5–1.0) ceramics have been investigated. SnO₂ improved the densification process and expanded the sintering temperature range effectively. Moreover, Sn⁴⁺ substituting for Si⁴⁺ sites leads to the emergence of Ca₃SnSi₂O₉ phase, which has a positive effect on the dielectric properties of CaO–SiO₂–SnO₂ materials, especially the Qf value. The Ca(Sn_0.1Si_0.9)O₃ ceramics sintered at 1375 °C possessed good microwave dielectric properties: ε_r =7.92, Qf =58,000 GHz and τ_f=−42 ppm/°C. The Ca(Sn_0.4Si_0.6)O₃ ceramics sintered at 1450 °C also exhibited good microwave dielectric properties of ε_r=9.27, Qf=63,000 GHz, and τ_f=−52 ppm/°C. Thus, they are promising candidate materials for millimeter-wave devices.