Comparative study of electromagnetic interference shielding properties of injection molded versus compression molded multi-walled carbon nanotube/polystyrene composites

This study compares electromagnetic interference (EMI) shielding properties of injection molded versus compression molded multi-walled carbon nanotube/polystyrene (MWCNT/PS) composites, i.e., properties such as EMI shielding effectiveness (EMI SE), electrical conductivity, real permittivity and imaginary permittivity. The injection molded (MWCNT-aligned) samples showed lower EMI shielding properties than compression molded (randomly distributed MWCNT) samples that was attributed to lower probability of MWCNTs contacting each other due to MWCNT alignment. The compression molded samples showed higher electrical conductivity and lower electrical percolation threshold than the injection molded samples. The compression molded samples at MWCNT concentrations of 5.00 and 20.0 wt.% showed real permittivity two times and imaginary permittivity five times greater than the injection molded samples. The EMI SE for the compression molded samples at MWCNT concentrations of 5.00 and 20.0 wt.% was 15.0 and 30.0 dB, respectively, significantly greater than EMI SE for the injection molded samples. Lower EMI SE for the injection molded samples was ascribed to lower electrical conductivity, real permittivity (polarization loss) and imaginary permittivity (Ohmic loss). Comparison of the EMI shielding properties of the compression molded versus injection molded samples confirmed that EMI shielding does not require filler connectivity; however it increases with filler connectivity.     

Electromagnetic interference shielding mechanisms of CNT/polymer composites

The electromagnetic interference (EMI) shielding mechanisms of multi-walled carbon nanotube (MWCNT)/polymer composites were analyzed experimentally and theoretically. For the experimental analysis, EMI shielding effectiveness (SE) of MWCNT/polypropylene (PP) composite plates made in three different thicknesses and at four different concentrations were studied. A model based on the shielding of electromagnetic plane wave was used to theoretically study the EMI shielding mechanisms. The experimental results showed that absorption is the major shielding mechanism and reflection is the secondary shielding mechanism. The modeling results demonstrated that multiple-reflection within MWCNT internal surfaces and between MWCNT external surfaces decrease the overall EMI SE. The EMI SE of MWCNT/PP composites increased with increase in MWCNT content and shielding plate thickness.     

Electromagnetic interference shielding effectiveness of MWCNT filled poly(ether sulfone) and poly(ether imide) nanocomposites

Multiwalled carbon nanotube (MWCNT) filled poly(ether sulfone) (PES) and poly(ether imide) (PEI) composites were prepared with different MWCNT weight fractions (0.5–5wt%) by a solution mixing technique. Their electrical conductivities, electromagnetic interference (EMI), shielding effectiveness (SE), return loss (RL), and absorption loss (AL) were investigated. Morphologies of the fracture surfaces of nanocomposites studied by scanning electron and transmission electron microscopy showed relatively good MWCNT dispersion and distribution. The electrical conductivity of compression molded samples measured at room temperature indicated that the electrical percolation network was achieved already at 0.5% loading. The measurements of shielding effectiveness (SE) carried out in the frequency range of 8 to 12 GHz (X‐band range) showed that SE increases with measurement frequency and with filler loading, whereby no significant differences could be observed between PES and PEI as matrices. The nanocomposites based on both matrices with 5 wt% loading of MWCNT exhibited shielding levels at 8 GHz between 42 and 45 dB in comparison with the pure polymers which showed value in the range of 1 to 2 dB. RL and AL showed significantly lower values for the composites as compared to unfilled polymers, but no systematic trends were observed on frequency. POLYM. ENG. SCI., 54:2560–2570, 2014. © 2013 Society of Plastics Engineers     

Electrical, morphological and rheological properties of carbon nanotube composites with polyethylene and poly(phenylene sulfide) by melt mixing

Electrical, morphological and rheological properties of polyethylene (PE)/multi-walled carbon nanotube (MWCNT) and poly(phenylene sulfide) (PPS)/MWCNT composites were studied with the MWCNT content using vector network analyzer, scanning electron microscopy and rotational rheometry. From the results of electrical conductivity and electromagnetic interference shielding efficiency (EMI SE) of the PE/MWCNT and PPS/MWCNT composites, the electrical percolation threshold of the composites has found to be 5 and 3 wt% MWCNT, respectively. From the results of the EMI SE of the composites, it was suggested that the increase in homogeneous dispersion of the MWCNT in the PPS matrix has been attributed to the increase in connectivity of the MWCNT-MWCNT network structure of the composite. Therefore, the higher values of the EMI SE with the MWCNT content were observed in the PPS/MWCNT than the PE/MWCNT composites. From the results of the rheological properties of the PE/MWCNT and PPS/MWCNT composites, the increase in the complex viscosity was observed for the PPS/MWCNT than the PE/MWCNT composites. The increase in complex viscosity maybe due to the increase in homogeneous dispersion of the MWCNT in the PPS matrix than that in the PE matrix. From the results of the rheological properties of the PE/MWCNT and PPS/MWCNT composites, it was suggested that the homogeneous dispersion of the MWCNT in the polymer matrix has affected the increase in complex viscosity of the PPS/MWCNT composite. This result of rheological behavior is consistent with the results of the EMI SE of the PE/MWCNT and PPS/MWCNT composites.     

Synergistic effect of multiwalled carbon nanotubes and an intumescent flame retardant: Toward an ideal electromagnetic interference shielding material with excellent flame retardancy

To shield undesirable electromagnetic waves caused by electronic devices and simultaneously resolve the flame safety of the electronic components, an electromagnetic interference (EMI) shielding material with excellent flame‐retardant properties is urgently needed. The synergistic effect of the intumescent flame retardant (IFR) and multiwalled carbon nanotubes (MWCNTs) for polystyrene (PS) nanocomposites prepared by melt blending was investigated. The results show that addition of certain amounts of IFRs facilitated the dispersion of MWCNTs in the PS matrix, and the percolation threshold of the MWCNTs in the PS matrix also decreased from 1.67 ± 0.05 to 1.29 ± 0.04 wt %. Moreover, the EMI shielding efficiencies (SEs) of the PS–MWCNT–IFR composites were consistently higher than those of the PS–MWCNT composites without the addition of the IFRs at the same MWCNT content; this indicated that the synergistic effect of the MWCNTs and IFRs effectively improved the EMI SE of the PS–MWCNT–IFR composites. Furthermore, the limiting oxygen index (LOI) testing results show that the LOI values of the PS–MWCNT composites were consistently higher than 27%; this indicated that the PS–MWCNT composites effectively met the needs of flame safety; this indicated that the PS–MWCNT–IFR composite is a novel and promising candidate for an ideal EMI shielding material with excellent flame‐retardant properties for today's electronic devices. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45088.     

The electrical conductivity and electromagnetic interference shielding of injection molded multi-walled carbon nanotube/polystyrene composites

Multi-walled carbon nanotube (MWCNT)/polystyrene (PS) composites were injection molded into a mold equipped with three different cavities. A high alignment of MWCNTs in PS was achieved by applying high shear force to the melt. The effects of gate and runner designs and processing conditions, i.e., mold temperature, melt temperature, injection/holding pressure and injection velocity, on the volume resistivity of the composites were investigated in both the thickness and in-flow directions. The experiments showed that volume resistivity could be varied up to 7 orders of magnitude by changing the processing conditions in the injection molded samples. The electromagnetic interference shielding effectiveness (EMI SE) of the molded composites was studied by considering the alignment of the MWCNTs. The EMI SE decreased with an increase in the alignment of the injection-molded MWCNTs in the PS matrix. This study shows that mold designs and processing conditions significantly influence the electrical conductivity and shielding behavior of injection molded CNT-filled composites.     

The effects of MWCNT length on the mechanical,crystallization and electromagnetic interference shielding effectiveness of PP/MWCNT composites

The length of multi-walled carbon nanotubes (MWCNT) has an important influence on the properties of polymer/MWCNT composites. This study aims to examine the influence of the length of MWCNT on the mechanical properties, distribution, melting and crystallization behavior, and electromagnetic interference shielding effectiveness (EMI SE) of PP/MWCNT composites. The test results show that MWCNT of a short length contribute to better mechanical properties and have a better dispersion in the matrix. MWCNT also serve as a nucleating agent for PP, thereby increasing the crystallization temperature (T_c). In particular, short MWCNT provide PP/MWCNT composites with a greater degree of cyrstallinity. The conjunction of 8 wt% long MWCNT in PP/MWCNT composites results in an optimal electrical resistivity of 65.02 Ω-cm, and an average EMI SE of ?29.47 dB. The polymer/MWCNT composites have properties that can be adjusted by using different lengths of MWCNT, which is advantageous for application in diverse products.     

Graphene nanoplate and multiwall carbon nanotube–embedded polycarbonate hybrid composites: High electromagnetic interference shielding with low percolation threshold

This study has reported the preparation of polycarbonate (PC)/graphene nanoplate (GNP)/multiwall carbon nanotube (MWCNT) hybrid composite by simple melt mixing method of PC with GNP and MWCNT at 330°C above the processing temperature of the PC (processing temperature is 280°C) followed by compression molding. Through optimizing the ratio of (GNP/MWCNT) in the composites, high electromagnetic interference shielding effectiveness (EMI SE) value (∼21.6 dB) was achieved at low (4 wt%) loading of (GNP/MWCNT) and electrical conductivity of ≈6.84 × 10⁻⁵ S.cm⁻¹ was achieved at 0.3 wt% (GNP/MWCNT) loading with low percolation threshold (≈0.072 wt%). The high temperature melt mixing of PC with nanofillers lowers the melt viscosity of the PC that has helped for better dispersion of the GNPs and MWCNTs in the PC matrix and plays a key factor for achieving high EMI shielding value and high electrical conductivity with low percolation threshold than ever reported in PC/MWCNT or PC/graphene composites. With this method, the formation of continuous conducting interconnected GNP‐CNT‐GNP or CNT‐GNP‐CNT network structure in the matrix polymer and strong π–π interaction between the electron rich phenyl rings and oxygen atom of PC chain, GNP, and MWCNT could be possible throughout the composites. POLYM. COMPOS., 37:2058–2069, 2016. © 2015 Society of Plastics Engineers     

Electrical conductivity and EMI shielding effectiveness of polyurethane foam–conductive filler composites

The morphological, electrical, and thermal properties of polyurethane foam (PUF)/single conductive filler composites and PUF/hybrid conductive filler composites were investigated. For the PUF/single conductive filler composites, the PUF/nickel‐coated carbon fiber (NCCF) composite showed higher electrical conductivity and electromagnetic interference shielding effectiveness (EMI SE) than did the PUF/multiwall carbon nanotube (MWCNT) and PUF/graphite composites; therefore, NCCF is the most effective filler among those tested in this study. For the PUF/hybrid conductive fillers PUF/NCCF (3.0 php)/MWCNT (3.0 php) composites, the values of electrical conductivity and EMI SE were determined to be 0.171 S/cm and 24.7 dB (decibel), respectively, which were the highest among the fillers investigated in this study. NCCF and MWCNT were the most effective primary and secondary fillers, and they had a synergistic effect on the electrical conductivity and EMI SE of the PUF/NCCF/MWCNT composites. From the results of thermal conductivity and cell size of the PUF/conductive filler composites, it is suggested that a reduction in cell size lowers the thermal conductivity of the PUF/conductive filler composites. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44373.     

High electromagnetic interference shielding with high electrical conductivity through selective dispersion of multiwall carbon nanotube in poly (ε‐caprolactone)/MWCNT composites

This study presents the preparation of electrically conducting poly(ε‐caprolactone) (PCL)/multiwall carbon nanotube (MWCNT) composites with very low percolation threshold (p_c). The method involves solution blending of PCL and MWCNT in the presence of commercial PCL beads. The PCL beads were added into high viscous PCL/MWCNT mixture during evaporation of solvent. Here, the used commercial PCL polymer beads act as an ‘excluded volume’ in the solution blended PCL/MWCNT region. Thus, the effective concentration of the MWCNT dramatically increases in the solution blended region and a strong interconnected continuous conductive network path of CNT−CNT is assumed throughout the matrix phase with the addition of PCL bead which plays a crucial role to improve the electromagnetic interference shielding effectiveness (EMI SE) and electrical conductivity at very low MWCNT loading. Thus, high EMI SE value (∼23.8 dB) was achieved at low MWCNT loading (1.8 wt %) in the presence of 70 wt % PCL bead and the high electrical conductivity of ∼2.49×10⁻² S cm⁻¹ was achieved at very low MWCNT loading (∼0.15 wt %) with 70 wt % PCL bead content in the composites. The electrical conductivity gradually increased with increasing the PCL bead concentration, as well as, MWCNT loading in the composites. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42161.     

Effect of oxyfluorination on electromagnetic interference shielding of polypyrrole-coated multi-walled carbon nanotubes

The polypyrrole-coated multi-walled carbon nanotubes (MWCNTs) were prepared by in situ chemical oxidative polymerization of pyrrole on the surface of MWCNTs for the novel electromagnetic interference (EMI) shielding materials. The oxyfluorination treatment on MWCNTs introduced the hydrophilic functional groups resulting in well distribution and higher interfacial affinity between polypyrrole (PPy) and MWCNTs. The PPy phases formed on MWCNTs were observed by SEM. The thickness of PPy on the surface of MWCNTs decreased as increasing the hydrophilic groups on MWCNTs by the oxyfluorination treatment. The PPy-coated MWCNT composites showed the remarkable increases in permittivity, permeability, and EMI shielding efficiency (SE). The EMI SE of PPy-coated MWCNTs increased up about 28.6 dB mainly based on the absorption mechanism.     

The influence of single-walled carbon nanotube structure on the electromagnetic interference shielding efficiency of its epoxy composites

Three types of single-walled carbon nanotube (SWCNT) homogeneous epoxy composites with different SWCNT loadings (0.01-15%) have been evaluated for electromagnetic interference (EMI) shielding effectiveness (SE) in the X-band range (8.2-12.4 GHz). The effect of the SWCNT structure including both the SWCNT aspect ratio and wall integrity, on the EMI SE have been studied and are found to correlate well with the conductivity and percolation results for these composites. The composites show very low conductivity thresholds (e.g. 0.062%). A 20-30 dB EMI SE has been obtained in the X-band range for 15% SWCNT loading, indicating that the composites can be used as effective lightweight EMI shielding materials. Furthermore, their EMI performance to radio frequencies is found to correspond well with their permittivity data.     

Electrical,rheological and electromagnetic interference shielding properties of thermoplastic polyurethane/carbon nanotube composites

Electrically conducting rubbery composites based on thermoplastic polyurethane (TPU) and carbon nanotubes (CNTs) were prepared through melt blending using a torque rheometer equipped with a mixing chamber. The electrical conductivity, morphology, rheological properties and electromagnetic interference shielding effectiveness (EMI SE) of the TPU/CNT composites were evaluated and also compared with those of carbon black (CB)‐filled TPU composites prepared under the same processing conditions. For both polymer systems, the insulator–conductor transition was very sharp and the electrical percolation threshold at room temperature was at CNT and CB contents of about 1.0 and 1.7 wt%, respectively. The EMI SE over the X‐band frequency range (8–12 GHz) for TPU/CNT and TPU/CB composites was investigated as a function of filler content. EMI SE and electrical conductivity increased with increasing amount of conductive filler, due to the formation of conductive pathways in the TPU matrix. TPU/CNT composites displayed higher electrical conductivity and EMI SE than TPU/CB composites with similar conductive filler content. EMI SE values found for TPU/CNT and TPU/CB composites containing 10 and 15 wt% conductive fillers, respectively, were in the range ?22 to ?20 dB, indicating that these composites are promising candidates for shielding applications. © 2013 Society of Chemical Industry     

Multiwalled carbon nanotubes–BaTiO3/silica composites with high complex permittivity and improved electromagnetic interference shielding at elevated temperature

Composites with silica matrix and mixed filler of multiwalled carbon nanotubes (MWCNTs) and BaTiO₃ powder were fabricated. Excellent uniform dispersion of MWCNTs can be obtained using a two-step mixing method. Both of the real and imaginary parts of complex permittivity increased with increasing MWCNT content and measured temperature. The electromagnetic interference (EMI) shielding results showed that the absorption mechanism is the main contribution to the total EMI shielding effectiveness (SE). Compared with the EMI SE resulting from reflection, the absorption showed more dependence on the MWCNT content, measured temperature and frequency. The total EMI SE is greater than 20 dB at 25 °C and 50 dB at 600 °C in the whole frequency range of 12.4–18 GHz with a 1.5 mm composite thickness, which suggests that the MWCNT–BaTiO₃/silica composites could be good candidates for the EMI shielding materials in the measured frequency and temperature region.     

Comparison of polyelectrolyte and sodium dodecyl benzene sulfonate as dispersants for multiwalled carbon nanotubes on cotton fabrics for electromagnetic interference shielding

Cotton fabrics with multiwalled carbon nanotubes (MWCNTs) dispersed by Nafion, a polyelectrolyte, and sodium dodecyl benzene sulfonate (SDBS), a surfactant, were prepared for electromagnetic interference (EMI) shielding. The fabrics were characterized by scanning electron microscopy and vector network analysis. The fabrics with the Nafion–MWCNT coating possessed a better shielding efficiency (SE) than those with the SDBS–MWCNT coating because of a more uniform dispersion of MWCNTs, which improved the electrical conductivity and EMI shielding properties. The maximum SE value of the fabric reached 11.48 dB, and the specific SE was 39.6 dB cm³/g. The reflectivity and absorptivity were calculated separately to determine the main mechanism of EMI shielding. The absorptivity was 68.6% at 12 GHz for the Nafion–MWCNT‐coated fabric; this showed that the dominant mechanism of EMI shielding for the treated fabrics was absorption. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40588.     

EMI shielding effectiveness of carbon based nanostructured polymeric materials: A comparative study

The microstructure, electromagnetic interference (EMI) shielding effectiveness (SE), DC electrical conductivity, AC electrical conductivity and complex permittivity of nanostructured polymeric materials filled with three different carbon nanofillers of different structures and intrinsic electrical properties were investigated. The nanofillers were multiwall carbon nanotubes (MWCNT), carbon nanofibers (CNF) and high structure carbon black (HS-CB) nanoparticles and the polymer was acrylonitrile-butadiene-styrene (ABS). In addition, the EMI SE mechanisms and the relation between the AC electrical conductivity in the X-band frequency range and the DC electrical conductivity were studied. The nanocomposites were fabricated by solution mixing and characterized by uniform dispersion of the nanofillers within the polymer matrix. It was found that, at the same nanofiller loading, the EMI SE, permittivity and electrical conductivity of the nanocomposites decreased in the following order: MWCNT > CNF > CB. MWCNT based nanocomposites exhibited the lowest electrical percolation threshold and the highest EMI SE owning to the higher aspect ratio and electrical conductivity of MWCNT compared to CNF and HS-CB. The AC conductivity in the X-band frequency range was found to be independent of frequency.     

Electrical conductivity and electromagnetic interference shielding of polyaniline/polyacrylate composite coatings

Lightweight and flexible composite coatings of p‐toluene sulfonic acid doped polyaniline (PANI–TSA) with various mass fractions and polyacrylate were prepared for electromagnetic interference (EMI) shielding. Both the volume and surface conductivities of the composite coatings increased with increasing PANI–TSA; furthermore, the volume conductivity showed a typical percolation behavior with a percolation threshold at about 0.21. The EMI shielding effectiveness (SE) of the PANI–TSA/polyacrylate coatings over the range of 14 kHz to 15 GHz increased with increasing PANI–TSA as the direct‐current conductivity did. EMI SE of the coatings at the low frequencies (14 kHz to 1 GHz) was around 30–80 dB, higher than that at the high frequencies (1–15 GHz); this indicated possible commercial application of the coatings for far‐field EMI shielding. The highest EMI SE value was 79 dB at 200 MHz with a coating thickness of 70 ± 5 μm. The moderate SE, light weight, and easy preparation of the coating are advantages for future applications for EMI shielding. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2149–2156, 2005     

Mild functionalization of carbon nanotubes filled epoxy composites: Effect on electromagnetic interferences shielding effectiveness

The effect of nitric acid mild functionalized multiwalled carbon nanotubes (MWCNTs) on electromagnetic interference (EMI) shielding effectiveness (SE) of epoxy composites was examined. MWCNTs were oxidized by concentrated nitric acid under reflux conditions, with different reaction times. The dispersion of MWCNTs after functionalization was improved due to the presence of oxygen functional groups on the nanotubes surface. Functionalization at 2 h exhibits the highest EMI SE and electrical conductivity of MWCNTs filled epoxy composites. However, EMI shielding performance of MWCNTs filled epoxy composite declined when the functionalization reaction time was prolonged. This was due to extensive damage on the MWCNT structure, as verified by a Raman spectroscope. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42557.     

Significantly enhanced electromagnetic interference shielding in Al2O3 ceramic composites incorporated with highly aligned non-woven carbon fibers

Macroscopic parallel aligned non-woven carbon fibers were incorporated into Al₂O₃ composites in this study to evaluate the contribution of multiple reflections to the total electric magnetic interference (EMI) shielding. Results indicate that parallel aligned non-woven carbon fiber layers contribute significantly to the total EMI shielding effectiveness (SE_T) of Al₂O₃ composites by largely enhancing the EMI absorption, and seven parallel aligned thin non-woven carbon fiber layers finally make the almost microwave-transparent Al₂O₃ an excellent EMI shielding material with an EMI SE_T as high as 29–32 dB in the X-band frequency range. The volume fraction of carbon fibers in Al₂O₃ composites with seven carbon fiber layers is calculated to be only 0.5%, and therefore the EMI SE enhancement efficiency by parallel aligned large non-woven carbon fiber layers is much higher than other highly conducting nano fillers. It validates the significance of multiple reflections in achieving high EMI shielding properties in ceramic composites and provides an instructive approach to design efficient EMI shielding ceramic composites.     

Effects of hybrid fillers on the electrical conductivity,EMI shielding effectiveness,and flame retardancy of PBT and PolyASA composites with carbon fiber and MWCNT

The effects of hybrid fillers of carbon fiber (CF) and multiwall carbon nanotube (MWCNT) on the electrical conductivity, electromagnetic interference shielding effectiveness (EMI SE), flame retardancy, and mechanical properties of poly(butylene terephthalate) (PBT)/poly(acrylonitrile-co-styrene-co-acrylate) (PolyASA) (70/30, wt %) with conductive filler composites were investigated. The CF was used as the main filler, and MWCNT was used as the secondary filler to investigate the hybrid filler effect. For the PBT/PolyASA/CF (8 vol %)/MWCNT (2 vol %) composite, a higher electrical conductivity (1.4 × 10⁰ S cm⁻¹) and EMI SE (33.7 dB) were observed than that of the composite prepared with the single filler of CF (10 vol %), which were 9.0 × 10⁻² S cm⁻¹ and 23.7 dB, respectively. This increase in the electrical properties might be due to the longer CF length and hybrid filler effect in the composites. From the results of aging test at 85 °C, 120 h, the electrical conductivity and EMI SE of the composites decreased slightly compared to that of the composite without aging. The results of electrical conductivity, EMI SE, and flame retardancy suggested that the composite with the hybrid fillers of CF and MWCNT showed a synergetic effect in the PBT/PolyASA/CF (8 vol %)/MWCNT (2 vol %) composite. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 48162.