Optimization of the dye-sensitized solar cell performance by mechanical compression

In this study, the P25 titanium dioxide (TiO₂) nanoparticle (NP) thin film was coated on the fluorine-doped tin oxide (FTO) glass substrate by a doctor blade method. The film then compressed mechanically to be the photoanode of dye-sensitized solar cells (DSSCs). Various compression pressures on TiO₂ NP film were tested to optimize the performance of DSSCs. The mechanical compression reduces TiO₂ inter-particle distance improving the electron transport efficiency. The UV–vis spectrophotometer and electrochemical impedance spectroscopy (EIS) were employed to quantify the light-harvesting efficiency and the charge transport impedance at various interfaces in DSSC, respectively. The incident photon-to-current conversion efficiency was also monitored. The results show that when the DSSC fabricated by the TiO₂ NP thin film compressed at pressure of 279 kg/cm², the minimum resistance of 9.38 Ω at dye/TiO₂ NP/electrolyte interfaces, the maximum short-circuit photocurrent density of 15.11 mA/cm², and the photoelectric conversion efficiency of 5.94% were observed. Compared to the DSSC fabricated by the non-compression of TiO₂ NP thin film, the overall conversion efficiency is improved over 19.5%. The study proves that under suitable compression pressure the performance of DSSC can be optimized.     

A natural tomato slurry as a photosensitizer for dye-sensitized solar cells with TiO2/CuO composite thin films

We have studied the performance of dye-sensitized solar cells by employing natural dye “anthocyanins” extracted from the tomato slurry as a sensitizer for the TiO₂/CuO photoanode. The extracts were anchored on TiO₂/CuO films deposited on an ITO substrate which was used as a photoanode. The dye adsorbed TiO₂/CuO films electrode, the copper plate as a counter electrode, and iodolyte as an electrolyte were assembled into DSSCs. The conversion efficiency of the DSSCs was found to be 2.96% with a V_OC of 0.615 V, J_SC of 6.6 mA/cm², and an FF of 0.73. This work highlights the use of contribution of the tomato slurry as a natural sensitizer to enhance the efficiency of DSSCs.     

Electrophoretic deposition of TiO2 film on titanium foil for a flexible dye-sensitized solar cell

Electrophoretic deposition (EPD) method is employed to obtain mesoporous TiO₂ film on a titanium (Ti) foil; the film is then mechanically compressed and sintered at 350 °C before being subjected to dyeing. A comprehensive study was made on the mechanistic aspects of the EPD process. The dye-sensitized solar cell (DSSC) using the thus formed TiO₂ film rendered a power conversion efficiency (Eff.) of 6.5%. Effects of various compression pressures on the photovoltaic parameters and on other characteristic parameters of the pertinent DSSCs are studied. Electrochemical impedance spectroscopy (EIS) is applied for the first time, using a novel equivalent model, to study the impedance behavior of the DSSC with this type of TiO₂ film. We also obtain characteristic parameters of the TiO₂ photoanode by using EIS. The coordination number of the TiO₂ film, and the ratio of charge transfer resistances of electron recombination and electron transport are also obtained and analyzed. Moreover, we employ a multilayer approach and increase the film thickness to prepare TiO₂ films with the same coordination number and porosity; DSSCs using such TiO₂ films obtained from P90 and P25 rendered efficiencies of 6.5% and 5.24%, respectively. Scanning electron microscopy (SEM) micrographs are obtained to characterize the TiO₂ films formed by the EPD technique and laser-induced transient technique is used to estimate the electron lifetime in the TiO₂ films.     

Solid-state dye-sensitized hierarchically structured ZnO solar cells

A novel solid-state hierarchically structured ZnO dye-sensitized solar cell (DSC) was assembled by using TiO₂ as filler in polyethylene oxide (PEO)/polyethylene glycol (PEG) electrolytes and ZnO nanocrystalline aggregates as photoanode film. Under optimized composite polyelectrolyte containing PEO/oligo-PEG/TiO₂/LiI/I₂ the photovoltaic performance of the solid-state ZnO DSCs was significantly better, with an overall conversion efficiency (η) of 1.8% under irradiation of 100 mW/cm², which was higher than those of the cells with PEO/TiO₂/LiI/I₂ (η = 1.1%) or PEO/oligo-PEG/LiI/I₂ electrolyte (η = 1.5%). Further, the hierarchically structured ZnO-based cell showed a higher η value of 2.0% under 60 mW/cm² radiation. The morphologies, ionic conductivity of three different composite electrolytes and their performance to the DSCs were also studied by FESEM, I–V data, IPCE and EIS.     

Plasmonic Effects of Infiltrated Silver Nanoparticles Inside TiO2 Film: Enhanced Photovoltaic Performance in DSSCs

The plasmonic effects of infiltrated silver (Ag) nanoparticles, with different contents, inside a nanostructured TiO₂ film on the photovoltaic performance of dye‐sensitized solar cells (DSSCs) are explored. The synthesized Ag nanoparticles are immobilized onto deposited TiO₂ nanoparticles by a new strategy using 3‐mercaptopropionic acid (MPA), a bifunctional linker molecule. Transmission electron microscope (TEM) images show that monodispersed Ag and polydispersed TiO₂ nanoparticles have an average diameter of 12 ± 3 nm and 5 ± 1 nm, respectively. Moreover, Fourier transform infrared spectroscopy (FTIR) analysis reveals that Ag nanoparticles were successfully functionalized and capped with MPA. Optical studies on the MPA‐capped Ag nanoparticles inside TiO₂ film show an increase in the total absorbance of the electrode. Moreover, EIS measurements confirm that MPA‐capped Ag nanoparticles inhibit the charge recombination and improve the stability of nanoparticles in I₃^?/I^? electrolyte. The DSSC assembled with optimal content of MPA‐capped Ag nanoparticles demonstrated an enhanced power conversion efficiency (8.82% ± 0.07%) compared with the pure TiO₂ (7.30% ± 0.05%). The increase in cell efficiency was attributed to the enhanced dye light absorption in strength and spectral range due to the surface plasmon resonance of MPA‐capped Ag nanoparticles in the photoanode.     

Titanium flexible photoanode consisting of an array of TiO2 nanotubes filled with a nanocomposite of TiO2 and graphite for dye-sensitized solar cells

A flexible dye-sensitized solar cell (DSSC) was fabricated using a photoanode consisting of an array of TiO₂ nanotubes (TNT) filled with a nanocomposite of TiO₂ (P90) and nanographite. The array of TNT was obtained by anodic oxidation of Ti foil, and this Ti foil with TNT was used as the photoanode of the DSSC. Each tube in the array has an average diameter of 100 nm. The morphologies of the array of TNT were obtained both after and before filling them with the TiO₂/graphite nanocomposite, using a field-emission scanning electron microscopy (FE-SEM). DSSC with photoanode consisting of the nanocomposite (photoanode designated as Graphite/P90-TNT) rendered a light-to-electricity conversion efficiency (η) of 5.75%. In contrast, the cells with photoanodes consisting of only TNT (photoanode designated as TNT) and TNT filled with P90-TiO₂ (photoanode designated as P90-TNT) exhibited efficiencies (η) of 4.44% and 5.14%, respectively. The enhancements in the η’s in favor of the cells with P90-TNT and Graphite/P90-TNT were attributed to the filled P90 and nanocomposite, respectively. The filled particles were assumed to provide more conductive pathways for electron transfer and prolonged lifetime for electrons in the film of TNT. The results were substantiated by light-absorption values, incident-photo-to-current efficiency (IPCE) curves, Nyquist and Bode plots of electrochemical impedance spectroscopy (EIS), and photopotential transient curves.     

The photovoltaic performance of dye-sensitized solar cells enhanced by using Dawson-type heteropolyacid and heteropoly blue-TiO2 composite films as photoanode

Dawson-type heteropolyacid {P₂Mo₁₈^VI} and its two-electron heteropoly blue {P₂Mo₂^VMo₁₆^VI}-doped TiO₂ composites have been successfully prepared by a simple sol–gel method and introduced into the photoanode of dye-sensitized solar cells (DSSCs), which results in a significant performance enhancement of DSSCs. The electrochemical impedance spectroscopy (EIS) and open-circuit voltage decay (OCVD) curve were employed to investigate the electron transport and carrier recombination behavior in DSSCs. The results show that doping with {P₂Mo₁₈^VI} and {P₂Mo₂^VMo₁₆^VI} could both suppress the dark current and increase the electron lifetime in DSSCs. The performance of DSSCs with both {P₂Mo₁₈^VI}-doped and {P₂Mo₂^VMo₁₆^VI}-doped photoanodes is better than that with pure P25 photoanodes and the overall conversion efficiency was improved by 24.48% and 17.19%, respectively.     

Fabrication and photoelectrochemical properties of TiO2 films on Ti substrate for flexible dye-sensitized solar cells

The dye-sensitized solar cells (DSSCs) using Ti foil supporting substrate for fabricating nanocrystalline TiO₂ flexible film electrodes were developed, intending to improve the photoelectrochemical properties of flexible substrate-based DSSCs. The obtained cells were characterized by electrochemical impedance spectra (EIS), open circuit voltage decay (OCVD) measurement and Tafel plots. The experimental results indicate that the most important advantage of a Ti foil-based TiO₂ flexible electrode over a FTO glass-based electrode lies in its reduced sheet resistance, electron traps, and the retarded back reaction of electrons with tri-iodine ions in DSSCs. All above characteristics for the Ti substrate TiO₂ films are beneficial for decreasing the charge recombination in the TiO₂ electrode and prolonging the electron lifetimes for the DSSCs, as well as improvement of the overall solar conversion efficiency. The photocurrent of the cell fabricated with the Ti foil-based flexible electrode increased significantly, leading to a much higher overall solar conversion efficiency of 5.45% at 100 mW/cm² than the cell made with FTO glass-based TiO₂ electrodes. Above results demonstrate that Ti foil is a potential alternative to the conventional FTO glass substrate for the DSSCs.     

Effect of compressed TiO2 nanoparticle thin film thickness on the performance of dye-sensitized solar cells

In this study, dye-sensitized solar cells (DSSCs) were fabricated using nanocrystalline titanium dioxide (TiO₂) nanoparticles as photoanode. Photoanode thin films were prepared by doctor blading method with 420 kg/cm² of mechanical compression process and heat treatment in the air at 500°C for 30 min. The optimal thickness of the TiO₂ NP photoanode is 26.6 μm with an efficiency of 9.01% under AM 1.5G illumination at 100 mW/cm². The efficiency is around two times higher than that of conventional DSSCs with an uncompressed photoanode. The open-circuit voltage of DSSCs decreases as the thickness increases. One DSSC (sample D) has the highest conversion efficiency while it has the maximum short-circuit current density. The results indicate that the short-circuit current density is a compromise between two conflict factors: enlargement of the surface area by increasing photoanode thickness and extension of the electron diffusion length to the electrode as the thickness increases.     

EIS analysis on low temperature fabrication of TiO2 porous films for dye-sensitized solar cells

A low temperature (<150 °C) fabrication method for preparation of TiO₂ porous films with high efficiency in dye-sensitized solar cells (DSSCs) has been developed. The Ti(IV) tetraisopropoxide (TTIP) was added to the paste of TiO₂ nanoparticles to interconnect the TiO₂ particles. The electrochemical impedance spectroscopy (EIS) technique was employed to quantify the charge transport resistance at the TiO₂/dye/electrolyte interface (R_ct2) and electron lifetime in the TiO₂ film (τ_e) under different molar ratios of TTIP/TiO₂ and also at various TiO₂ thicknesses. It was found that the R_ct2 decreased as the molar ratio increased from 0.02 to 0.08, however, it increased at a molar ratio of 0.2 due to the reduction in surface area for dye adsorption. In addition, the characteristic frequency peak shifted to lower frequency at a molar ratio of 0.08, indicating the longer electron lifetime. As for the thickness effect, TiO₂ film with a thickness around 17 μm achieved the best cell efficiency. EIS study also confirmed that, under illumination, the smallest R_ct2 was associated with a TiO₂ thickness of 17 μm, with the R_ct2 increased as the thickness of TiO₂ film increased. In the Bode plots, the characteristic frequency peaks shifted to higher frequency when the thickness of TiO₂ increased from 17.2 to 48.2 μm, indicating the electron recombination increases as the thickness of the TiO₂ electrode increases.Finally, to make better use of longer wavelength light, 30 wt% of larger TiO₂ particle (300 nm) was mixed with P25 TiO₂ as light scattering particles. It effectively increased the short-circuit current density and cell conversion efficiency from 7.44 to 8.80 mA cm⁻² and 3.75 to 4.20%, respectively.     

Enhancing the performance of dye-sensitized solar cells based on an organic dye by incorporating TiO2 nanotube in a TiO2 nanoparticle film

The photoelectrochemical properties of a high molar extinction coefficient charge transfer organic dye containing thienylfluorene segment called FL, and the effect of incorporating TiO₂ nanotube (TiNT) in TiO₂ nanoparticle film along with the above dye on the photovoltaic performance of dye-sensitized solar cells (DSSCs) were investigated. The influence of soaking time of the TiO₂ electrode in dye solution and the effect of varying its concentration, on the solar cell efficiency was also studied. Cyclic voltammetric (CV) analysis revealed the linear relationship between the anodic peak current and the scan rate, indicating a surface-confined diffusion process.The surface morphology of TiNT was characterized using SEM, TEM and XRD. The open-circuit voltage (V_OC) of the DSSC increased with the increase in the wt% of TiNT and shows optimal value at about 5 wt%, which is correlated with the suppression of the electron recombination as found out from the electron lifetime studies.The electrochemical impedance spectroscopy (EIS) technique was employed to quantify the charge transport resistance (R_ct) and electron lifetime under different ratios of the TiNT/nanoparticle. The electron lifetimes of the DSSCs based on FL and N3 dye were very close to one another and the DSSC based on the FL showed respectable photovoltaic performance of ca. 7.8% under the light intensity of 100 mW cm⁻² (AM 1.5G).     

Novel photo-crosslinkable polymeric electrolyte system based on poly(ethylene glycol) and trimethylolpropane triacrylate for dye-sensitized solar cell with long-term stability

Polyethylene glycol (PEG) and trimethylolpropane triacrylate (TMPTA) were used as photo-crosslinkable polymer electrolytes for dye-sensitized solar cells (DSSCs). PEG and trifunctional TMPTA formed a crosslinked structure upon light illumination, as confirmed by the solubility test and FTIR spectroscopy. In order to make close contact with the TiO₂ porous film, the polymeric electrolyte was prepared by photo-polymerization after injecting the monomer electrolyte solution into the porous film. The cross-sectional FE-SEM images showed the penetration of the electrolyte into the porous TiO₂ layer. Under AM 1.5 (100 mW/cm²) light irradiation for up to 30 min, a maximum 21% increase in the photo-conversion efficiency (η%) was observed. The electrolyte containing PEG and 20 wt% TMPTA showed a maximum increase in the photo-conversion efficiency from 2.75% to 3.35% with 30 min of light illumination. Also, the DSSCs with the novel crosslinkable PEG/TMPTA based polymer electrolyte showed improved long-term stability in comparison to those with electrolytes containing only PEG.     

Quasi solid state dye-sensitized solar cells with modified TiO2 photoelectrodes and triphenylamine-based dye

Quasi solid state dye-sensitized solar cells (DSSCs) have been fabricated with organic sol or TiCl₄ modified TiO₂ and porous TiO₂ photoanode and a triphenylamine-based dye (TPAR3) used as photosensitizer. Dark current measurements suggested that both modified TiO₂ photoelectrodes had significantly reduced the recombination rate of photoelectrons due to the reduced bare FTO surface in comparison to porous photoelectrode. The DSSC based on modified TiO₂ photoelectrodes showed improved photovoltaic parameters compared to the porous TiO₂ photoelectrode. The overall power conversion efficiency (PCE) is 3.27%, 4.73% and 6.8% for porous, TiCl₄ modified and sol modified TiO₂ photoelectrodes, respectively. The improved PCE with modified TiO₂ electrodes was attributed to the formation of a compact layer. This effectively improves adherence of TiO₂ to FTO surface, providing a larger TiO₂/FTO contact area and reducing the electron recombination by blocking the direct contact between redox electrolyte and the conductive FTO surface and enhances the electron collection efficiency.     

The influence of anatase-rutile mixed phase and ZnO blocking layer on dye-sensitized solar cells based on TiO2nanofiberphotoanodes

High performance is expected in dye-sensitized solar cells (DSSCs) that utilize one-dimensional (1-D) TiO₂ nanostructures owing to the effective electron transport. However, due to the low dye adsorption, mainly because of their smooth surfaces, 1-D TiO₂ DSSCs show relatively lower efficiencies than nanoparticle-based ones. Herein, we demonstrate a very simple approach using thick TiO₂ electrospun nanofiber films as photoanodes to obtain high conversion efficiency. To improve the performance of the DSCCs, anatase-rutile mixed-phase TiO₂ nanofibers are achieved by increasing sintering temperature above 500°C, and very thin ZnO films are deposited by atomic layer deposition (ALD) method as blocking layers. With approximately 40-μm-thick mixed-phase (approximately 15.6?wt.% rutile) TiO₂ nanofiber as photoanode and 15-nm-thick compact ZnO film as a blocking layer in DSSC, the photoelectric conversion efficiency and short-circuit current are measured as 8.01% and 17.3?mA?cm^?2, respectively. Intensity-modulated photocurrent spectroscopy and intensity-modulated photovoltage spectroscopy measurements reveal that extremely large electron diffusion length is the key point to support the usage of thick TiO₂ nanofibers as photoanodes with very thin ZnO blocking layers to obtain high photocurrents and high conversion efficiencies.     

Double‐Layer Structure Photoanode with TiO2 Nanotubes and Nanoparticles for Dye‐Sensitized Solar Cells

Here, we report a novel double‐layer structure photoanode with TiO₂ nanotube (TNT) layer and TiO₂ nanoparticle (TP) layer via a two‐step method of electrochemical anodization and screen printing for dye‐sensitized solar cells (DSSCs). The results indicate that DSSCs with this double‐layer structure have significant advantages of large surface area, long electron lifetime, superior electron recombination restraint characteristics, and high light scattering. The layer thickness of nanotubes and nanoparticles is also investigated and finally an optimized double‐layer structure with excellent performance is prepared. With such a double‐layer structure photoanode, DSSC with a relative high conversion efficiency of 6.43% and a short‐circuit photocurrent density of 16.40 mA·cm^?2 is obtained.     

An efficient and low-cost TiO2 compact layer for performance improvement of dye-sensitized solar cells

A TiO₂ organic sol was synthesised for the preparation of a compact TiO₂ layer on fluorine-doped tin oxide (FTO) glass by a dip-coating technique. The resultant thin film was used for the fabrication of dye-sensitized solar cells (DSSCs). The compact layer typically has a thickness of ca. 110 nm as indicated by its SEM, and consists of anatase as confirmed by the XRD pattern. Compared with the traditional DSSCs without this compact layer, the solar energy-to-electricity conversion efficiency, short-circuit current and open-circuit potential of the DSSCs with the compact layer were improved by 33.3%, 20.3%, and 10.2%, respectively. This can be attributed to the merits brought by the compact layer. It can effectively improve adherence of TiO₂ to FTO surface, provide a larger TiO₂/FTO contact area, and reduce the electron recombination by blocking the direct contact between the redox electrolyte and the conductive FTO surface.     

Dye-sensitized solar cells based on double-layered TiO2 composite films and enhanced photovoltaic performance

Dye-sensitized solar cells (DSSCs) are fabricated based on double-layered composite films of TiO₂ nanoparticles and hollow spheres. The photoelectric conversion performances of DSSCs based on nanoparticles/nanoparticles (PP), hollow spheres/hollow spheres (HH), hollow spheres/nanoparticles (HP), and nanoparticles/hollow spheres (PH) double-layered films are investigated, and their photo-electric conversion efficiencies are 4.33, 4.72, 4.93 and 5.28%, respectively. The enhanced performance of TiO₂ nanoparticles/hollow spheres double-layered composite film solar cells can be attributed to the combined effect of following factors. The light scattering of overlayer hollow spheres enhances harvesting light of the DSSCs and the underlayer TiO₂ nanoparticle layer ensures good electronic contact between film electrode and the F-doped tin oxide (FTO) glass substrate. Furthermore, the high surface areas and pore volume of TiO₂ hollow spheres are respectively beneficial to adsorption of dye molecules and transfer of electrolyte solution.     

Hydrothermal Growth and Application of ZnO Nanowire Films with ZnO and TiO2 Buffer Layers in Dye-Sensitized Solar Cells

This paper reports the effects of the seed layers prepared by spin-coating and dip-coating methods on the morphology and density of ZnO nanowire arrays, thus on the performance of ZnO nanowire-based dye-sensitized solar cells (DSSCs). The nanowire films with the thick ZnO buffer layer (~0.8–1 μm thick) can improve the open circuit voltage of the DSSCs through suppressing carrier recombination, however, and cause the decrease of dye loading absorbed on ZnO nanowires. In order to further investigate the effect of TiO₂ buffer layer on the performance of ZnO nanowire-based DSSCs, compared with the ZnO nanowire-based DSSCs without a compact TiO₂ buffer layer, the photovoltaic conversion efficiency and open circuit voltage of the ZnO DSSCs with the compact TiO₂ layer (~50 nm thick) were improved by 3.9–12.5 and 2.4–41.7%, respectively. This can be attributed to the introduction of the compact TiO₂ layer prepared by sputtering method, which effectively suppressed carrier recombination occurring across both the film–electrolyte interface and the substrate–electrolyte interface.     

Au Nanoparticles as Interfacial Layer for CdS Quantum Dot-sensitized Solar Cells

Quantum dot-sensitized solar cells based on fluorine-doped tin oxide (FTO)/Au/TiO₂/CdS photoanode and polysulfide electrolyte are fabricated. Au nanoparticles (NPs) as interfacial layer between FTO and TiO₂ layer are dip-coated on FTO surface. The structure, morphology and impedance of the photoanodes and the photovoltaic performance of the cells are investigated. A power conversion efficiency of 1.62% has been obtained for FTO/Au/TiO₂/CdS cell, which is about 88% higher than that for FTO/TiO₂/CdS cell (0.86%). The easier transport of excited electron and the suppression of charge recombination in the photoanode due to the introduction of Au NP layer should be responsible for the performance enhancement of the cell.     

Preparation of TiO<Subscript>2</Subscript> nanotube/nanoparticle composite particles and their applications in dye-sensitized solar cells

Efficiency of dye-sensitized solar cells [DSSCs] was enhanced by combining the use of TiO₂ nanotubes [TNTs] and nanoparticles. TNTs were fabricated by a sol-gel method, and TiO₂ powders were produced through an alkali hydrothermal transformation. DSSCs were constructed using TNTs and TiO₂ nanoparticles at various weight percentages. TNTs and TiO₂ nanoparticles were coated onto FTO glass by the screen printing method. The DSSCs were fabricated using ruthenium(II) (N-719) and electrolyte (I₃/I₃ ^-) dyes. The crystalline structure and morphology were characterized by X-ray diffraction and using a scanning electron microscope. The absorption spectra were measured using an UV-Vis spectrometer. The incident photocurrent conversion efficiency was measured using a solar simulator (100 mW/cm²). The DSSCs based on TNT/TiO₂ nanoparticle hybrids showed better photovoltaic performance than cells made purely of TiO₂ nanoparticles.