Sorption of heavy metal ions from aqueous solution by a novel cast PVA/TiO2 nanohybrid adsorbent functionalized with amine groups

Sorption of Cd(II), Ni(II) and U(VI) ions onto a novel cast PVA/TiO₂/APTES nanohybrid adsorbent with variations in adsorbent dose, pH, contact time, initial metal concentration and temperature has been investigated. The adsorbent were characterized by SEM and FTIR analysis. BET surface area, pore diameter and pore volume of adsorbent were 35.98 m² g⁻¹, 3.08 nm and 0.059 cm³ g⁻¹, respectively. The kinetic and equilibrium data were accurately described by the double-exponential and Freundlich models for all metals. The maximum sorption capacities were 49.0, 13.1 and 36.1 mg g⁻¹ for Cd(II), Ni(II) and U(VI) ions with pH of 5.5, 5 and 4.5, respectively. Thermodynamic studies showed that the sorption process was favored at higher temperature. The adsorbent can be easily regenerated after 5 cycles of sorption–desorption.     

Controllable synthesis of mesoporous alumina with large surface area for high and fast fluoride removal

Gamma phase of mesoporous alumina (MA) with large surface area was successfully synthesized by a facile hydrothermal method followed by thermal treatment for fluoride removal. The as-synthesized MA nanoparticles with average size of 20 nm–150 nm have ordered wormhole-like mesoporous structure. The pore size is 5 nm with a narrow distribution, and the specific surface area reaches 357 m² g⁻¹ while the bulk density is 0.45 cm³ g⁻¹. Glucose as a small-molecule template plays an important role on the morphology, surface area and pore diameter of the MA. As an ionic adsorbent for fluoride removal, the maximum adsorption capacity of MA is 8.25 mg g⁻¹, and the remove efficiency reaches 90% in several minutes at pH of 3. The Langmuir equilibrium model is found to be suitable for describing the fluoride sorption on MA and the adsorption behavior follows the pseudo-second-order equation well with a correlation coefficient larger than 0.99. The larger surface area and relatively narrow pore size of MA are believed to be responsible for improving the adsorption efficiency for fluoride in aqueous solution.     

Preparation and one-step activation of microporous carbon nanofibers for use as supercapacitor electrodes

Microporous carbon nanofibers were prepared by electrospinning from resole-type phenolic resin, followed by one-step activation. KOH was utilized to tune the fiber diameter and improve porous texture. By adjusting KOH content in the spinning solution, the fiber diameter could be controlled in the range of 252–666 nm and the microporous volume and specific surface area could be greatly improved. The electrochemical measurements in 6 M KOH aqueous solution showed that the microporous carbon nanofibers possessed high specific capacitance, considerable rate performance, and superior specific surface capacitance to conventional microporous carbons. The maximal specific capacitance of 256 F g⁻¹ and high specific surface capacitance of 0.51 F m⁻² were achieved at 0.2 A g⁻¹. Furthermore, the specific capacitance could still remain 170 F g⁻¹ at 20 A g⁻¹ with the retention of 67%. Analysis showed that the high specific surface capacitance of the resultant carbons was mainly attributed to optimized pore size (0.7–1.2 nm) and the excellent rate performance should be principally due to the reduced ion transportation distance derived from the nanometer-scaled fibers.     

Novel synthesis of mesoporous hydroxyapatite using carbon nanorods as a hard-template

A novel hard-template synthesis approach for the fabrication of mesoporous hydroxyapatite (HAP) is described herein. Carbon nanorods, synthesised using mesoporous silica (SBA-15) and an acidified sucrose solution, are used as a hard template, after which, they are utilised to synthesise mesoporous HAP. Transmission electron microscopy (TEM), X-ray diffraction (XRD) energy-dispersive X-ray spectroscopy (EDX) and nitrogen adsorption/Brunauer–Emmett–Teller (BET), are all employed to characterise the synthesised materials. We demonstrate that this approach allows for the successful fabrication of single phase HAP with surface area 242.20±2.27 m² g⁻¹ and average pore diameter 3.5 nm and 18.9 nm. This work proposes for the first time a bespoke innovative procedure that employs carbon nanorods as a template for the synthesis of mesoporous HAP via a hard templating protocol.     

Soft-templated mesoporous carbons as potential materials for oral drug delivery

Template-synthesized mesoporous carbons were successfully used in in vitro investigations of controlled delivery of three model drugs, captopril, furosemide, and ranitidine hydrochloride (HCl). Captopril and furosemide exhibited desorption kinetics over 30–40 h, and ranitidine. HCl had a complete release time of 5–10 h. As evident from the slow release kinetics, the mesoporous carbons have excellent potential for the controlled-release media of the specific drugs targeted towards oral delivery. The mesoporous carbons, synthesized from phloroglucinol and lignin, a synthetic and a sustainable precursor, respectively, exhibit BET surface area of 200–400 m² g⁻¹ and pore volume of 0.2–0.6 cm³ g⁻¹. The synthetic carbon has narrower pore widths and higher pore volume than the renewable counterpart and maintains a longer release time. The release kinetics reveals that the diffusivities of the drugs from carbon media are of equivalent magnitude (10⁻²² to 10⁻²⁴ m² s⁻¹). However, a tailored reduction of pore width in the sorbent reduces the diffusivity of smaller drug molecule by an order of magnitude. Thus, engineered pore morphology, along with its functionalization potential for specific interaction, can be exploited for optimal delivery system of a preferred drug.     

Process intensification approach for preparation of curcumin nanoparticles via solvent–nonsolvent nanoprecipitation using spinning disc reactor

Continuous preparation of curcumin nanoparticles via solvent–nonsolvent (S-NS) precipitation by using spinning disc reactor was investigated. The process intensification by spinning disc reactor (SDR) along with the comparative study of conventional mechanical agitated contactor was carried out. Solvent used for curcumin precipitation in this study was ethanol whereas non-solvent deionised water. Influences of various operating parameters for spinning disc process; such as flow rate of S-NS, S-NS ratio, concentration of curcumin, disc characteristics, concentration of protecting agent and rotating disc speed were examined on the nanoparticles size. The average optimum curcumin particles size was obtained in the range 180–220 nm in consideration with particles size distribution at a flow rate of 200 mL min⁻¹; curcumin concentration of 0.5 g L⁻¹ in ethanol; polyvinylpyrilodine (PVP) concentration of 1 g L⁻¹ in deionised water; S:NS ratio 1:4 and operating disc speed of 1500 rpm. Particles were characterized by using XRD, FT-IR, DSC and SEM which showed decrease in the crystallinity after the nanoprecipitation of curcumin. The dissolution rates of the fabricated curcumin nanoparticle were found drastically higher than original curcumin.     

Simple fabrication of a Fe2O3/carbon composite for use in a high-performance lithium ion battery

A simple approach was developed for the fabrication of a Fe₂O₃/carbon composite by impregnating activated carbon with a ferric nitrate solution and calcinating it. The composite contains graphitic layers and 10 wt.% Fe₂O₃ particles of 20–50 nm in diameter. The composite has a high specific surface area of ∼828 m² g⁻¹ and when used as the anode in a lithium ion battery (LIB), it showed a reversible capacity of 623 mAh g⁻¹ for the first 100 cycles at 50 mA g⁻¹. A discharge capacity higher than 450 mAh g⁻¹ at 1000 mA g⁻¹ was recorded in rate performance testing. This highly improved reversible capacity and rate performance is attributed to the combination of (i) the formation of graphitic layers in the composite, which possibly improves the matrix electrical conductivity, (ii) the interconnected porous channels whose diameters ranges from the macro- to meso- pore, which increases lithium-ion mobility, and (iii) the Fe₂O₃ nanoparticles that facilitate the transport of electrons and shorten the distance for Li⁺ diffusion. This study provides a cost-effective, highly efficient means to fabricate materials which combine conducting carbon with nanoparticles of metal or metal oxide for the development of a high-performance LIB.     

Fabrication of nitrogen-doped hierarchically porous carbons through a hybrid dual-template route for CO2 capture and haemoperfusion

Hierarchically porous carbon materials have many important technological applications; however, most of them were fabricated using either expensive materials or complicated procedures. Based on a general chelate-assisted multi-component co-assembly strategy, nitrogen-doped hierarchically porous carbon materials were fabricated by using Al-based composite and commercial triblock copolymer Pluronic F127 as co-templates, and natural banana peel as precursor. This versatile strategy allowed to easily achieve tunable surface area (700–2100 m² g⁻¹), pore volume (0.38–1.65 cm³ g⁻¹) and a narrow average mesoporous size of ca. 2.72–4.03 nm by simply varying the dosages of Al³⁺ and F127, and to attain high N content (4.54 wt%) in a large-scale fabrication system (2 L). X-ray photoelectron spectroscope characterization of the as-prepared sample revealed nitrogen atoms are mainly in the form of pyridinic nitrogen, quaternary nitrogen and pyridine-N-oxide. Importantly, these as-obtained carbon materials showed excellent performance in CO₂ capture and bilirubin removal with high adsorption capacities and selectivities. The present fabrication strategy is also applicable to the design of porous carbons doped with other elements by choosing appropriate biomass precursors.     

High-surface area carbons from renewable sources with a bimodal micro-mesoporosity for high-performance ionic liquid-based supercapacitors

Highly porous materials with a bimodal pore size distribution in the micro-mesopore range have been produced from biomass by adding melamine to the hydrochar/KOH mixture used in the activation process. These carbons are characterized by BET surface areas in excess of ∼3300 m² g⁻¹ and a porosity equally distributed between micropores and mesopores. The use of melamine in the synthesis process not only extends the pore size distribution into the mesopore region, but leads to the incorporation of a certain amount of nitrogen atoms into the carbon framework. These materials combine high ion adsorption capacities (micropores) and enhanced ion-transport kinetics (mesopores) leading to an outstanding capacitive performance in ionic liquid-based supercapacitors. Thus, they have specific capacitances >160 F g⁻¹ at 1 A g⁻¹ and >140 F g⁻¹ at 60 A g⁻¹ in both pure ionic liquid and in acetonitrile-diluted ionic liquid, enabling these materials to store up to a maximum of ca. 60 W h kg⁻¹ in both kinds of electrolytes and deliver ca. 20 W h kg⁻¹ at ∼42 kW kg⁻¹ (discharge time ca. 2 s) in pure ionic liquid and ∼25–30 W h kg⁻¹ at ∼97–100 kW kg⁻¹ (discharge time ∼1 s) in acetonitrile-diluted ionic liquid.     

Template-free synthesis of mesoporous γ-alumina with tunable structural properties

Mesoporous γ-Al₂O₃ (MA) with agglomerated nanoparticles was successfully synthesized by using aluminum sulfate as inorganic Al resource, and hexamethylene tetramine (HMTA) as precipitant without using any surfactants, via a hydrothermal method. All the experimental processes experienced the hydrolysis, precipitation and calcination steps. The structural and morphological properties of uncalcined and calcined samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared (FT-IR) spectroscopy, thermogravimetry differential thermal gravity (TG-DTG) and N₂ adsorption–desorption. The bulk density of the sample is 0.682 cm³  g⁻¹, and the specific surface area is 273.302 m² g⁻¹. The pore diameters (7.1 nm and 9.7 nm) indicate that a typical bimodal mesoporous structure was formed within MA. In order to tune the structural properties of MA, various kinds of inorganic aluminum sources and precipitating agents were employed to carry out contrast experiments, which leaded to regular variations in the specific surface area (200.898–273.302 m² g⁻¹), pore volume (0.121–1.327 cm³ g⁻¹) and pore size (3.7–35.9 nm). At the same time, the experimental results also demonstrated that the various kinds of Al resources and precipitants had no effects on the crystal structure of MA. However, the morphologies of samples, such as nanoparticles, short fibers, flower-like and block-shaped, can be controlled effectively. The present study provides a simple and effective approach for preparing MA, and the structural properties of MA can be controlled precisely by carefully choosing aluminum sources and precipitants. The approach of this work not only allows us to investigate the growth mechanism of the final product, but also reduces cost and the environmental pollution effectively than other template methods.     

Polymer-derived mesoporous Ni/SiOC(H) ceramic nanocomposites for efficient removal of acid fuchsin

In this paper, magnetic porous Ni-modified SiOC(H) ceramic nanocomposites (Ni/SiOC(H)) were successfully prepared via a template-free polymer-derived ceramic route, which involves pyrolysis at 600 °C of nickel-modified allylhydridopolycarbosilane (AHPCS-Ni) precursors synthesized by the reaction of allylhydridopolycarbosilane (AHPCS) with nickel(II)acetylacetonate (Ni(acac)₂). The resultant Ni/SiOC(H) nanocomposites are comprised of in-situ formed nanoscaled Ni socialized with small amounts of NiO and nickel silicides embedded in the amorphous SiOC(H) matrix. The materials show ferromagnetic behavior and excellent magnetic properties with the saturation magnetization in the range of 1.71–7.08 emu g⁻¹. Besides, the Ni/SiOC(H) nanocomposites are predominantly mesoporous with a high BET surface area and pore volume in the range of 253–344 and 0.134–0.185 cm³ g⁻¹, respectively. The measured porosity features cause an excellent adsorption capacity towards a template dye acid fuchsin with the adsorption capacity Q_t at 10 min of 80.7–85.8 mg g⁻¹ and the Q_e at equilibrium of 123.8–129.8 mg g⁻¹.     

An advanced method to manufacture hierarchically structured carbide-derived carbon monoliths

The preparation of carbide-derived carbon (CDC) monoliths with a hierarchically structure in the nm and μm range is presented. Basis is the manufacturing of porous cellular SiC ceramics based on a biomorphous approach with μm porosity and subsequent conformal conversion to CDC by reactive extraction with chlorine. The SiC ceramics can be sintered at low temperatures and short times (1500 °C, 2 h) compared to classical preparation methods. The SiC ceramics show a macro pore volume (1–10 μm channel size) of 0.56 ml g⁻¹, which corresponds to 1.5 ml g⁻¹ in the resulting CDC. The final carbon material exhibits an additional nano pore volume of 0.525 ml g⁻¹ with a mean slit pore size of 0.86 nm. Mechanical stabilities of the highly porous CDC are excellent (bending strength 2.1 ± 0.2 MPa, corrected Weibull modulus 8.7, characteristic strength 2.2 MPa and Youngs modulus 10.0 ± 0.5 GPa). The reactive extraction of the carbide monoliths shows very high reaction rates, approx. two dimensions faster (95×) compared to non-porous samples. Thus the manufacturing of the structured carbide and CDC can be performed at lower costs.     

Mesoporous carbon nanofibers with large cage-like pores activated by tin dioxide and their use in supercapacitor and catalyst support

The mesoporous carbon nanofibers (MCFs) with large cage-like pores have been fabricated by thermally treating electrospun fibers of polyvinyl alcohol containing tin compound. During the process, tin oxide is reduced to melting tin and the carbon is activated to form the porous carbon. The results of X-ray diffraction and transmission electron microscopy at different temperatures show that particles of SnO₂ (∼1.9 nm) exist in the fibers at 300 °C while mixtures of Sn and SnO with rod-like shapes appear in the matrix when the fibers are heated at 400 °C, and that Sn migrates to the surface of fibers and pores are formed in the fibers at higher temperature. Specific surface area of MCFs can reach 800 m² g⁻¹ and the average diameter of interior pores is about 10.3 nm while the entrance pores are small. The specific capacitance of MCFs is 105 F g⁻¹ and the fabricated symmetrical capacitors exhibit high-rate capacitive properties and excellent stability, Pt nanoparticles which can be densely loaded on MCFs exhibit relatively high activity and stability toward electro-oxidation of methanol, which indicate that MCFs may be used as electrodes for high-rate energy storage and support for catalyst. This approach may be extended to prepare other porous carbon materials.     

3D network-like porous MnCo2O4 by the sucrose-assisted combustion method for high-performance supercapacitors

3D network-like porous MnCo₂O₄ nanostructures have been successfully fabricated through a facile and scalable sucrose-assisted combustion route followed by calcination treatment. Benefiting from its advantages of the unique 3D network-like architectures with large specific surface area (216.15 m² g⁻¹), abundant mesoporosity (2–50 nm) and high electronic conductivity, the as-prepared MnCo₂O₄ electrode displays a high specific capacitance of 647.42 F g⁻¹ at a current density of 1 A g⁻¹, remarkable capacitance retention rate of 70.67% at current density of 10 A g⁻¹ compared with 1 A g⁻¹, and excellent cycle stability (only 6.32% loss after 3000 cycles). The excellent electrochemical performances coupled with facile and cost effective method will render the as-fabricated 3D network-like porous MnCo₂O₄ as a promising electrode material for supercapacitors.     

Impregnation assisted synthesis of 3D nitrogen-doped porous carbon with high capacitance

Three-dimensional (3D) porous carbons with controlled mesopore and micropore structures were prepared through a simple and low-cost ultrasonic and impregnation assisted method from waste air-laid paper. The ammonia management was used to dope the 3D porous carbons with different types of nitrogen heteroatoms in a way that replaced carbon atoms. The N₂ adsorption–desorption characterization suggested that the nitrogen-doped carbons have a high surface area of 1470 m² g⁻¹ with the average pore diameter of 4.2 nm, which are conducive to form electric double layer under high current density. The resulting 3D carbon exhibited a higher capacitance at 296 F g⁻¹ in comparison with the nitrogen-free one at 252 F g⁻¹ in 6 M KOH electrolyte. Moreover, a high power density ca. 0.313 kW kg⁻¹ and energy density ca. 34.3 Wh kg⁻¹ were achieved in the ionic liquid ([EMIm]BF₄). The findings will open a new avenue to use waste materials for high-performance energy-storage devices.     

Mesoporous N-containing carbon nanosheets towards high-performance electrochemical capacitors

We developed a direct carbonization strategy to efficiently fabricate mesoporous N-containing carbon nanosheets (N-CNSs) by using polyaniline nanosheets as a carbon precursor. Physicochemical characterizations revealed that the as-synthesized N-CNSs with 5.9 wt.% N species possessed a well-developed mesoporous architecture with large specific surface area of 352 m² g⁻¹, high mesoporous volume of 0.32 cm³ g⁻¹, and average pore size of ∼5.2 nm. When further utilized as an electrode for electrochemical capacitors, the mesoporous N-CNSs delivered a large specific capacitance of 239 F g⁻¹ at 0.5 A g⁻¹, and even 197 F g⁻¹ at a high current load of 8 A g⁻¹, indicating its good rate behavior. Furthermore, the capacitance degradation of ∼4% over continuous 5000 charge–discharge cycles at 6 A g⁻¹ further verified its good electrochemical stability at high rates for long-term electrochemical capacitors application.     

Evaluating the photocatalytic activity of Pt/TNT film catalyst

TiO₂ nanotubes (TNT) were prepared by a hydrothermal method from the commercially available TiO₂-P25. Five types of TNT were produced at different temperatures (120 °C, 130 °C, and 150 °C) and by using different reaction times (12 h, 24 h, and 30 h). The photocatalytic reactor that was used is a film catalytic reactor, in which the height of the catalyst is 1.0 mm. The BET and FESEM analysis results showed that TNT130-24 (130 °C, 24 h) and TNT150-12 (150 °C, 12 h) possessed well-formed tubular structures with a high specific surface area (282.9–316.7 m² g⁻¹) and large pore volumes (0.62–0.70 cm³ g⁻¹). However, TNT120-30 (120 °C, 30 h) presented the best photocatalytic activity upon CO removal due to the synergistic effect of TiO₂ nanotubes and TiO₂ particles. After the TNT catalysts were modified with Pt particles, the removal efficiency was in the order of Pt/TNT120-30>Pt/TNT130-24>Pt/P25. Pt/TNT120-30 showed 99% removal efficiency in a continuous photoreactor with a high space velocity of 1.79×10⁴ h⁻¹. The results of the TEM and DRS analyses confirmed that the Pt particles enhanced the photocatalytic reaction, which was attributed to the well-dispersed nature of the 1 nm nanoscaled Pt particles on the surfaces of the TNT catalysts, and narrowed the band gap from 3.22 eV to 3.01 eV.     

Amorphous CoS nanoparticle/reduced graphene oxide composite as high-performance anode material for sodium-ion batteries

Transition metal sulfides have been proved as promising candidates of anode materials for sodium-ion batteries (SIBs) due to their high sodium storage capacity, low cost and enhanced safety. In this study, the amorphous CoS nanoparticle/reduced graphene oxide (CoS/rGO) composite has been fabricated by a facile one-step electron beam radiation route to in situ decorate amorphous CoS nanoparticle on the rGO nanosheets. Benefiting from the small particle size (~2 nm), amorphous structure, and electronic conductive rGO nanosheets, the CoS/rGO nanocomposite exhibits high sodium storage capacity (440 mAh g⁻¹ at 100 mA g⁻¹), excellent cycling stability (277 mAh g⁻¹ after 100 cycles at 200 mA g⁻¹, 79.6% capacity retention) and high rate capability (149.5 mAh g⁻¹ at 2 A g⁻¹). The results provide a facile approach to fabricate promising amorphous and ultrafine metal sulfides for energy storage.     

Preparation of hollow mesoporous silica spheres by a sol–gel/emulsion approach

Hollow mesoporous silica spheres were synthesized by a sol–gel/emulsion (oil-in-water/ethanol) approach, in which cetyltrimethylammonium bromide (CTAB) surfactant was employed to stabilize and direct the hydrolysis of oil droplets of tetraethoxysilane (TEOS). The diameters of the hollow spheres can be tuned in the range from 210 to 720 nm by varying the ratio of ethanol-to-water and their shell thickness can be mediated by changing the concentration of CTAB used in the system. BET surface areas of the hollow silica spheres are determined to be in the range of 924–1766 m² g^?1 and their pore sizes are around 3.10 nm as determined by BJH method.     

Enhanced anode performance of micro/meso-porous reduced graphene oxide prepared from carbide-derived carbon for energy storage devices

Micro/meso-porous reduced graphite oxide (MMRGO) nanosheets were produced using precursor carbide-derived carbon (CDC), which was produced at a high temperature of 1200 °C, through a massive wet chemistry synthetic route involving graphite oxidation and microwave reduction. X-ray diffraction (XRD) and transmission electron microscopy (TEM) show that the MMRGO nanosheets were fabricated with 2–3 layers and ripple-like corrugations. N₂ sorption isotherms confirmed that micro/meso-pores coexisted in the RGO sample from CDC. In the anode application of Li-ion batteries, this RGO sample had an enhanced capacity performance at the 0.1 C rate and 1 C rate, with ∼1200 mAh g⁻¹ at the 100th cycle and ∼1000 mAh g⁻¹ at the 200th cycle, respectively.