Corrosion behavior of TiC particle-reinforced 304 stainless steel

TiC particle-reinforced 304 stainless steels were prepared using a new developed in situ technology and their corrosion behavior was compared with that of 304SS in 5 wt.% HCl solution. As compared to 304SS, E_corr, E_pit and E_rp values had shifted to a more negative region in 304SS containing TiC, indicating faster corrosion rate by TiC addition. The addition of TiC particles to 304SS resulted in no rapid pit propagation but maintained a high corrosion rate in the whole immersion time investigated.     

KCl-induced high temperature corrosion of the austenitic Fe-Cr-Ni alloys 304L and Sanicro 28 at 600 °C

The influence of KCl(s) on the high temperature oxidation of the austenitic alloys 304L and Sanicro 28 at 600 °C in O₂ + H₂O environment is reported. 0.10 mg/cm² KCl(s) was added before exposure. The samples are investigated by grazing angle XRD, SEM/EDX, and AES. In the absence of KCl, both alloys show protective behaviour in dry O₂. In O₂ + H₂O environment, alloy 304L suffers local breakaway corrosion while Sanicro 28 still shows protective behaviour. The oxidation of both alloys is strongly accelerated by KCl. KCl reacts with chromium in the normally protective corundum-type oxide, forming K₂CrO₄. This depletes the scale in chromia and leads to the formation of a non-protective, iron-rich scale. The significance of KCl-induced corrosion in real applications is discussed and the oxidation behaviour of the two steels is compared.     

Effect of copper on metal dusting of austenitic stainless steels

Three steels, 304SS, 310SS and 800H, were alloyed with 5%, 10%, and 20% (by weight) copper, and then exposed to 68%CO-31%H₂-1%H₂O gas at 680 °C (a_C = 19 and p_O2=5.4×10^-25 atm) under thermal cycling conditions. Kinetic measurements showed that copper-free alloys all dusted, with 304SS experiencing the greatest metal wastage. Copper additions did not have any effect on metal wastage of 304SS, but reduced the attack on 310SS and 800H markedly at levels of 5% and 10%. However, increasing the copper content to 20% produced large copper-rich precipitates which accelerated dusting by promoting internal graphitisation.Dusting was associated with surface coking. When pitting occurred, on copper-free alloys and on copper containing 304SS, large coke structures grew above the pits. Internal grain boundary carburisation always took place, and intragranular carbides also precipitated when dusting occurred. A lamellar surface layer of internally precipitated spinel and austenite also developed in association with dusting. The copper effect is discussed in terms of its alloy solubility and its known beneficial effect in Ni-Cu binaries.     

Improving the high-temperature oxidation resistance of a β-γ TiAl alloy by a Cr2AlC coating

A Cr₂AlC coating was deposited on a β-γ TiAl alloy. Isothermal oxidation tests at 700 °C and 800 °C, and thermocyclic oxidation at 800 °C were performed in air. The results indicated that serious oxidation occurred on the bare alloy. Thick non-protective oxide scales consisting of mixed TiO₂ + α-Al₂O₃ layers formed on the alloy surface. The coated specimens exhibited much better oxidation behaviour by forming an Al-rich oxide scale on the coating surface during the initial stages of oxidation. This scale acts as diffusion barrier by effectively blocking the ingress of oxygen, and effectively protects the coated alloys from further oxidation.     

Corrosion assessment of nitric acid grade austenitic stainless steels

The corrosion resistance of three indigenous nitric acid grade (NAG) type 304L stainless steel (SS), designated as 304L1, 304L2 and 304L3 and two commercial NAG SS designated as Uranus-16 similar to 304L composition and Uranus-65 similar to type 310L SS were carried out in nitric acid media. Electrochemical measurements and surface film analysis were performed to evaluate the corrosion resistance and passive film property in 6 N and 11.5 N HNO₃ media. The results in 6 N HNO₃ show that the indigenous NAG 304L SS and Uranus-65 alloy exhibited similar and higher corrosion resistance with lower passive current density compared to Uranus-16 alloy. In higher concentration of 11.5 N HNO₃, transpassive potential of all the NAG SS shows a similar range, except for Uranus-16 alloy. Optical micrographs of all the NAG SS revealed changes in microstructure after polarization in 6 N and 11.5 N HNO₃ with corrosion attacks at the grain boundaries. Frequency response of the AC impedance of all the NAG SS showed a single semicircle arc. Higher polarization resistance (R_P) and lower capacitance value (CPE-T) revealing higher film stability for indigenous NAG type 304L SS and Uranus-65 alloy. Uranus-16 alloy exhibited the lowest R_P value in both the nitric acid concentration. Auger electron spectroscopy (AES) study in 6 N and 11.5 N HNO₃ revealed that the passive films were mainly composed of Cr₂O₃ and Fe₂O₃ for all the alloys. The corrosion resistance of different NAG SS to HNO₃ corrosion and its relation to compositional variations of the NAG alloys are discussed in this paper.     

Temperature and water vapour effects on the cyclic oxidation behaviour of Fe-Cr alloys

Binary Fe-Cr alloys were subjected to cyclic oxidation at 600, 700 and 950 °C in flowing gases of Ar-20O₂ and Ar-20O₂-5H₂O (vol.%). The minimum chromium concentration required to achieve protective scale growth decreased as temperature increased from 600 to 700 °C. This change is attributed to faster chromium diffusion at higher temperature. Conversely, this minimum chromium level increased when the temperature was raised from 700 to 950 °C. This is attributed to faster scale growth, leading to its rapid mechanical failure, along with formation of slow-diffusing austenite. Water vapour accelerated scaling, leading to a need for higher chromium concentrations to resist breakaway oxidation.     

Effect of water vapor on annealing scale formation on 316 SS

The oxidation behavior of 316 stainless steel (SS) annealed in air containing 0.1 atm water vapor at temperatures ranging from 800 to 1030 °C was investigated. A kinetic study of the oxidation was made by employing thermal-gravimetric analysis (TGA). The morphology, composition and structure of the scale were examined by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The experimental results showed that significant breakaway oxidation occurred, resulting in substantial weight increase, as the steel was annealed in moist air at temperatures above 950 °C. The scaling behavior of 316 SS in wet air at 1030 °C could be divided into two stages based on the alteration of the oxidation rate. In each stage, the scale on 316 SS exhibited a different structure and morphology. The complex process of the formation of scale in wet air was discussed and proposed.     

Influence of grain size on the oxidation behavior of NbCr2 alloys at 950-1200 °C

The oxidation behavior of mechanically alloyed microcrystalline NbCr₂ intermetallics was investigated at 950-1200 °C in air by SEM in comparison with coarse-grain cast alloys. Results indicate that the mechanically alloyed alloys possess a better oxidation resistance and are less permeable to nitrogen than the cast alloys. At 1200 °C, the mechanically alloyed NbCr₂ alloys show a better resistance to scale spallation than the cast materials. The differences observed above are attributed to the finer grains increasing the relaxation of the oxide scale stress and improving the adhesion of the oxide layer on the matrix.     

Oxidation performance of Mo3Si with Al additions

The Mo₃Si alloys with different aluminum contents were fabricated by the arc-melting and drop-casting technique, heat treated and then exposed to air at 700, 800, 900 and 1000 °C in order to assess their oxidation behavior. Line scan studies led to the assumption that the oxide scale thermally grown at 1000 °C was composed of SiO₂ which was located closer to the alloy matrix and Al₂O₃ around the outer surface of the oxidized sample, while the Mo oxide volatilized at this oxidation temperature. The results also showed that the unalloyed sample (Mo₃Si) underwent a pest reaction in a short time of exposure, while the sample with 16 at.% Al exhibited the best oxidation behavior, which could be attributed to the formation of SiO₂ and Al₂O₃ in the oxide scale.     

The nature of the third-element effect in the oxidation of Fe-xCr-3 at.% Al alloys in 1 atm O2 at 1000 °C

The oxidation of an Fe-Al alloy containing 3 at.% Al and of four ternary Fe-Cr-Al alloys with the same Al content plus 2, 3, 5 or 10 at.% Cr has been studied in 1 atm O₂ at 1000 °C. Both Fe-3Al and Fe-2Cr-3Al formed external iron-rich scales associated with an internal oxidation of Al or of Cr+Al. The addition of 3 at.% Cr to Fe-3Al was able to stop the internal oxidation of Al only on a fraction of the alloy surface covered by scales containing mixtures of the oxides of the three alloy components, but not beneath the iron-rich oxide nodules which covered the remaining alloy surface. Fe-5Cr-3Al formed very irregular external scales where areas covered by a thin protective oxide layer alternated with others covered by thick scales containing mixtures of the oxides of the three alloy components, undergrown by a thin layer rich in Cr and Al, while internal oxidation was completely absent. Conversely, Fe-10Cr-3Al formed very thin, slowly-growing external Al₂O₃scales, providing an example of third-element effect (TEE). However, the TEE due to the Cr addition to Fe-3Al was not directly associated with a prevention of the internal oxidation of Al, but rather with the inhibition of the growth of external scales containing iron oxides. This behavior has been interpreted on the basis of a qualitative oxidation map for ternary Fe-Cr-Al alloys taking into account the existence of a complete solid solubility between Cr₂O₃ and Al₂O₃.     

Detection of breakaway oxidation with Acoustic Emission during titanium oxide scale growth

Extensive in-situ analysis of high temperature breakaway oxidation of titanium metal has been performed using the Acoustic Emission (AE) technique. Depending on temperature and oxidising atmosphere, different model cases were examined: with breakaway (900 °C/O₂), without breakaway (750 °C/O₂ and 900 °C/H₂O). Two specific population of AE hits were observed before and after breakaway. Contrary to the pre-breakaway population, the post-breakaway population exhibited low AE activity characterised by high values of energy. A critical energy value of E = 3 fJ was determined as a frontier between signals resulting from oxide parabolic growth and signals resulting from rapid linear growth.     

Isothermal oxidation behaviour of Nb-W-Cr Alloys

A study of the effect of Cr content on the microstructure and isothermal oxidation behaviour of four alloys from the Nb-Cr-W system has been performed. Selection of specific alloy compositions has been based on the ternary isothermal sections. Oxidation experiments were conducted in air at 900 and 1300 °C for 24 h under isothermal conditions. Weight gain per unit area as function of the temperature has been used to evaluate the oxidation resistance. The phases present in the alloys and the oxide scales were characterized by XRD, SEM, and EDS. Microstructure consists of Nb solid solution and NbCr₂, Laves phase. The oxidation kinetics follows a parabolic behaviour at 1300 °C; the addition of 30% Cr resulted in the significant reduction of the parabolic oxidation rate. At 900 °C, alloys with higher Cr content exhibit higher oxidation rates in comparison to alloys with lower Cr content. The oxidation products are a mixture of CrNbO₄ and Nb₂O₅ and the amount of each oxide present in the mixture is related to the intermetallic phase content and the oxidation temperature. The characterization results delineate the effect of the Cr content on the oxidation mechanisms of these alloys that represent a promising base for high-temperature alloy development.     

Oxidation Behavior of In Situ-Synthesized (TiB+TiC)/Ti6242 Composites

The oxidation behaviors of TiB and TiC particle-reinforced, titanium-matrix composites (TMCs) were studied in air at 550–650°C, The oxidation kinetics follow approximately a parabolic rate law. The oxidation rates, which were lower than those of Ti6242, decrease gradually as oxidation proceeds. The oxide scales formed on TMCs were predominantly rutile and α-Al₂O₃. No B₂O₃ and other oxides were observed within the oxide scale. The in situ-synthesized TiB and TiC reinforcements can increase the oxidation resistance of TMCs. The oxide scales that formed exhibited excellent spallation resistance under all testing conditions. No scale cracking or spallation could be observed, implying that growth and thermal stresses generated during heating and cooling have been effectively released. The mechanisms of the decrease in oxidation rate and the improvement on spallation resistance are discussed based on microstructure studies.     

High temperature corrosion of pure Fe, Cr and Fe-Cr binary alloys in O2 containing trace KCl vapour at 750 °C

Pure Fe, Cr and Fe-Cr binary alloys were corroded in O₂ containing 298 ppm KCl vapour at 750 °C. The corrosion kinetics were determined, and the microstructure and the composition of oxide scales were examined. During corrosion process, KCl vapour reacted with the formed oxide scales and generated Cl₂ gas. As Cl₂ gas introduced the active oxidation, a multilayer oxide scales consisted of an outmost Fe₂O₃ layer and an inner Cr₂O₃ layer formed on the Fe-Cr alloys with lower Cr concentration. In the case of Fe-60Cr or Fe-80Cr alloys, monolayer Cr₂O₃ formed as the healing oxidation process. However, multilayer Cr₂O₃ formed on pure Cr.     

High-temperature oxidation of Fe-Cr alloys in wet oxygen

Fe-Cr binary alloys have been oxidized in a stream of oxygen containing different amounts of water vapor at 900–1000°C to study the effects of water vapor. The Fe-Cr alloys exhibit an initial protective behavior due to formation of a Cr-rich scale and followed by a nonprotective breakaway oxidation due to formation of iron-rich scale. The appearance of the breakaway oxidation was very sensitive to the water vapor content in the atmosphere. The higher the water vapor content, the earlier the breakaway oxidation takes place. Increasing the oxidizing temperature or decreasing the Cr content in the alloys facilitate an earlier breakaway oxidation. The breakaway oxidation was inhibited effectively by surface-applied CeO₂ particles before oxidation. The oxide scales were examined and analyzed by optical metallography, X-ray diffraction, SEM, and EPMA. A mechanism of the effects of water vapor has been proposed.     

Effects of water vapour on isothermal oxidation of chromia-forming alloys in Ar/O2 and Ar/H2 atmospheres

Fe9Cr, Fe17Cr and Fe25Cr alloys were subjected to isothermal oxidation in Ar/O₂ and Ar/H₂ atmosphere at 700 °C as high temperature corrosion for 48 h. Oxidation weight change measurement showed increasing Cr content reduced the oxidation rate. The oxidized Cr alloys were analysed using SEM, TEM and XRD. The addition of water vapour accelerates the onset of breakaway oxidation kinetics for Fe9Cr. The presence of water vapour promotes internal oxidation of Cr within Fe9Cr. For Fe17Cr and Fe25Cr, the water vapour effect is not significant due to the large Cr reservoir due to continue growth of Cr₂O₃.     

The high-temperature oxidation of bulk nanocrystalline 304 stainless steel in air

The high-temperature oxidation of bulk nanocrystalline 304 stainless steel (BN-SS304) and its conventional polycrystalline counterpart (CP-SS304) in air at 900 °C for 24 h were studied by thermogravimetric analysis, X-ray photoelectron spectroscopy and scanning electron microscope. We studied the valence electron configurations of BN-SS304, CP-SS304 and their oxide scales by ultra-violet photoelectron spectroscopy. The high-temperature oxidation resistance of BN-SS304 was enhanced in both initial and isothermal oxidation, which was attributed to its larger work function and more chemical stability, its more chemically stable and compact oxide scale, its weaker O₂ adsorption and diffusion, its weaker Cr and Mn atoms diffusions.     

Oxidation of 316 stainless steel in supercritical water

The oxide scales of 316 stainless steel (316 SS) have been examined after exposure to supercritical water (SCW) with 2.0% H₂O₂ for up to 250 h. The exposed samples were analyzed using weight measurement, scanning electron microscopy (SEM), and X-ray diffraction analysis (XRD). It was found that mass gain of all samples increased with increasing temperature and exposure time. Higher temperature SCW resulted in rougher surfaces and thicker oxide scales. Duplex layer oxide structures with Ni-enrichment at the oxide/metal interface developed on all samples exposed to SCW, which were identified as Fe₂O₃/Fe₃O₄ + spinel/Cr₂O₃/Ni-enrichment/316 SS from the outer to inner layer. The possible oxidation mechanisms are also discussed.     

Oxidation of single crystal PWA 1483 at 950 °C in flowing air

The oxidation behaviour of single crystal PWA 1483 at 950 °C was investigated by means of XRD, SEM and EDS. The parabolic oxidation behaviour, as defined by mass gain and the respective oxide layer thicknesses, is characterized by a parabolic rate constant of about 4 × 10⁻⁶ mg²/(cm⁴ × s) and the formation of a multi-layered oxide scale. An outer scale contains a Ti-bearing thin film composed of TiO₂ and NiTiO₃ but mostly Cr in Cr₂O₃ and (Ni/Co)Cr₂O₄ besides NiTaO₄. This outer scale is connected to a discontinuous layer of Al₂O₃ and an area of γ′-depletion within the base material.     

Investigation of the HCl (g) attack on pre-oxidized pure Fe, Cr, Ni and commercial 304 steel at 400 °C

The paper presents the results from an investigation studying the ability of pre-oxidized metals and alloys to withstand chlorine attack in the form of gaseous HCl. The materials under investigation were pure Fe (s), Cr (s), Ni (s), and a commercial 18Cr-10Ni-Fe (304) alloy. The samples were pre-oxidized in different well defined environments, dry 10 vol.% O₂ (g) + N₂ (bal.), 10 vol.% O₂ (g) + 5 vol.% H₂O (g) + N₂ (bal.) and 10 vol.% O₂ (g) + 250 vppm SO₂ (g) + N₂ (bal.) for 24 h at 400 °C using a horizontal tube furnace. Afterwards the oxide films were characterized by GI-XRD, FEG-SEM, XPS and ToF-SIMS. The samples were then exposed further in 10 vol.% O₂ (g) + 500 vppm HCl (g) + x (x = 5 vol.% H₂O (g), 250 vppm SO₂ (g)) + N₂ (bal.). The exposure time was 100 h and after the exposures during the cool down process the reaction chamber was flushed with dry 10 vol.% O₂ (g) + N₂ (bal.). The corroded samples were then examined by the same techniques mentioned before. HCl (g) showed mainly to be aggressive toward the Fe (s) samples that form a relatively thick and porous oxide scale consisting of layered Fe₂O₃ (s)/Fe₃O₄ (s) during pre-oxidation, and the aggressiveness did not depend on the pre-oxidation conditions. All the other materials formed thin and dense oxides (20-100 nm) during pre-oxidation, and they did not suffer accelerated oxidation caused by HCl (g) during the subsequent exposure. The only exception was Ni (s) that had been pre-oxidized in an atmosphere containing SO₂ (g), in this case Ni sulphides and sulphates were formed during pre-oxidation which in turn caused accelerated oxidation to Ni when subsequently exposed to HCl (g). HCl (g) readily reacts with NiSO₄ (s) and Ni₃S₂ (s) and forms NiCl₂ (s) and SO₃ (g).