A comparative study of the corrosion inhibition of mild steel in sulphuric acid by 4,4-dimethyloxazolidine-2-thione

The corrosion protection of mild steel in a 2.5 M H₂SO₄ solution by 4,4-dimethyloxazolidine-2-thione (DMT) was studied at different temperatures by measuring changes in open circuit potential (OCP), potentiodynamic polarisation and electrochemical impedance spectroscopy (EIS). Corrosion current densities calculated from EIS data were comparable to those obtained from polarisation measurements. Results showed that DMT inhibited mild steel corrosion in a 2.5 M H₂SO₄ solution and indicated that the inhibition efficiencies increased with the concentration of inhibitor, but decreased proportionally with temperature. Polarisation curves showed that DMT is a mixed-type inhibitor. Changes in impedance parameters suggested the adsorption of DMT on the mild steel surface, leading to the formation of protective films. The DMT adsorption on the mild steel surface followed the Langmuir adsorption isotherm. The kinetic and thermodynamic parameters for dissolution and adsorption were investigated. Comprehensive adsorption (physisorption and chemisorption) of the inhibitor molecules on the mild steel surface was suggested based on the thermodynamic adsorption parameters.     

Inhibiting effects of butyl triphenyl phosphonium bromide on corrosion of mild steel in 0.5 M sulphuric acid solution and its adsorption characteristics

Butyl triphenyl phosphonium bromide (BuTPPB) has been evaluated as a corrosion inhibitor for mild steel in 0.5 M H₂SO₄ solutions using galvanostatic polarisation and potentiostatic polarisation measurements. The study was also complemented by infra red (IR) spectroscopy, scanning electron microscopy (SEM) and quantum chemical calculations. Galvanostatic polarisation measurements showed that the presence of BuTPPB in aerated 0.5 M H₂SO₄ solutions decreases corrosion currents to a great extent and the corrosion rate decreases with increasing inhibitor concentration at a constant temperature. At 298K, inhibition efficiency was found to be 94.5% for 10⁻⁷ M BuTPPB which increased to about 99% for the BuTPPB concentration of 10⁻² M. The effect of temperature on the corrosion behaviour of mild steel was studied at five different temperatures ranging from 298 to 338K. The polarisation curves clearly indicate that BuTPPB acts as a mixed type inhibitor. Adsorption of BuTPPB on the mild steel surface follows the Langmuir isotherm.Potentiostatic polarisation measurements showed that passivation was observed only for lower BuTPPB concentrations (10⁻⁵ and 10⁻⁷ mol l⁻¹) for the mild steel in 0.5 M H₂SO₄. IR and SEM investigations also confirmed the adsorption of BuTPPB on the mild steel surface in 0.5 M H₂SO₄ solutions. The molecular parameters obtained using PM3 semi-empirical method, were correlated with the experimentally measured inhibitor efficiencies.     

Synergistic effect of halide ions on improving corrosion inhibition behaviour of benzisothiozole-3-piperizine hydrochloride on mild steel in 0.5 M H2SO4 medium

The synergistic effect of iodide ions and benzisothiozole-3-piperizine hydrochloride (BITP) on corrosion inhibition of mild steel in 0.5 M H₂SO₄ solution has been studied by both chemical and electrochemical methods. The corrosion performance of BITP in 1.0 M HCl and 0.5 M H₂SO₄ media was examined and compared. The adsorption of BITP and its combination with iodide ions on mild steel surface followed Langmuir adsorption isotherm via chemisorption mechanism. The calculated values of synergism parameter (S_θ) were found to be greater than unity. This result clearly showed the existence of synergism between iodide ions and BITP molecules.     

The inhibition of mild steel corrosion in acidic medium by 1-methyl-3-pyridin-2-yl-thiourea

The effect of 1-methyl-3-pyridin-2-yl-thiourea on the corrosion resistance of mild steel in H₂SO₄ solution was investigated by different techniques. The results show that the inhibition efficiency increases with the increase of inhibitor concentration. This compound affects both the anodic dissolution of steel and the hydrogen evolution reaction in 0.5 M H₂SO₄. The adsorption of this inhibitor is also found to obey the Langmuir adsorption isotherm. From the adsorption isotherm, value of the ΔG_ads for the adsorption process was calculated. From the corrosion rate obtained at 25-45 ± 1 °C E_a, ΔH_a and possible mechanism have been proposed.     

Inhibitive properties, thermodynamic and quantum chemical studies of alloxazine on mild steel corrosion in H2SO4

Alloxazine (ALLOX) was tested as corrosion inhibitor for mild steel in 0.5 M H₂SO₄ solution using non-electrochemical technique (gravimetric and UV–Visible spectrophotometric measurements) at 303–333 K. ALLOX acts as inhibitor for mild steel in acidic medium. Inhibition efficiency increases with increase in concentration of ALLOX but decrease with rise in temperature. The adsorption of ALLOX was found to follow Temkin adsorption isotherm model. Both the activation and thermodynamic parameters governing the adsorption process were calculated and discussed. The adsorption follows a first-order kinetics. DFT study gave further insight into the mechanism of inhibition action of ALLOX.     

Inhibition effect of 6-benzylaminopurine on the corrosion of cold rolled steel in H2SO4 solution

The inhibition effect of 6-benzylaminopurine (BAP) on the corrosion of cold rolled steel (CRS) in 1.0-7.0 M H₂SO₄ at 25-50 °C was studied by weight loss and potentiodynamic polarization methods. Fourier transform infrared spectroscopy (FTIR) and atomic force microscope (AFM) were used to characterize the CRS surface. The results showed that BAP was a good inhibitor in 1.0 M H₂SO₄, and the adsorption of BAP obeyed the Temkin adsorption isotherm. Polarization curves showed that BAP acted as a mixed-type inhibitor in sulfuric acid. Depending on the results, the inhibitive mechanism was proposed.     

Experimental and molecular dynamics studies on corrosion inhibition of mild steel by 2-amino-5-phenyl-1,3,4-thiadiazole

The corrosion inhibition of mild steel in 0.5 M H₂SO₄ and 1.0 M HCl by 2-amino-5-phenyl-1,3,4-thiadiazole (APT) has been studied using potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) measurements. The results show that the inhibition efficiency increases with the increase of APT concentration in both acids, and the higher inhibition efficiency is obtained in 0.5 M H₂SO₄. The adsorption of APT molecules on the steel surface obeys Langmuir adsorption isotherm in both acids, and occurs spontaneously. The molecular dynamics method has also been used to simulate the adsorption of ATP molecule and solvent ions on the iron surface. The results show that with the adsorption of sulfate ions the Fe + anion + APT system has the higher negative interaction energy comparing to the case of the adsorption of chloride ions.     

Caffeic acid as a green corrosion inhibitor for mild steel

The inhibitor effect of the naturally occurring biological molecule caffeic acid on the corrosion of mild steel in 0.1 M H₂SO₄ was investigated by weight loss, potentiodynamic polarization, electrochemical impedance and Raman spectroscopy. The different techniques confirmed the adsorption of caffeic acid onto the mild steel surface and consequently the inhibition of the corrosion process. Caffeic acid acts by decreasing the available cathodic reaction area and modifying the activation energy of the anodic reaction. A mechanism is proposed to explain the inhibitory action of the corrosion inhibitor.     

Substitutional adsorption isotherms and corrosion inhibitive properties of some oxadiazol-triazole derivative in acidic solution

A newly synthesized oxadiazol-triazole derivative (TOMP), was investigated as corrosion inhibitor of mild steel in 0.5 M H₂SO₄ solution using weight loss measurements, polarization and electrochemical impedance spectroscopy (EIS) methods. Results obtained revealed that TOMP is effective corrosion inhibitor for mild steel in sulphuric acid and its efficiency attains more than 97.6% at 298 K. The number of water molecules (X) replaced by a molecule of organic adsorbate was determined from the substitutional adsorption isotherms applied to the data obtained from the weight loss experiments performed on mild steel specimen in acidic solution in the 298-333 K range.     

Corrosion monitoring of mild steel in sulphuric acid solutions in presence of some thiazole derivatives – Molecular dynamics, chemical and electrochemical studies

The physical behavior of three selected thiazole derivatives, namely 2-Amino-4-(p-tolyl)thiazole (APT), 2-Methoxy-1,3-thiazole (MTT) and Thiazole-4-carboxaldehyde (TCA) at iron (1 1 0) surface dissolved in aqueous solution were studied via molecular dynamics (MD) simulations. From the calculated binding energies, APT showed preferred adsorption on the steel surface among the three tested thiazole derivatives. The inhibition performance of the three thiazoles on the corrosion of mild steel in 0.5 M H₂SO₄ solutions was investigated at 25 °C. Measurements were conducted under various experimental conditions using weight loss, Tafel polarization and electrochemical impedance spectroscopy. Electrochemical frequency modulation (EFM) technique was also employed here to make accurate determination of the corrosion rates and test validation of the Tafel extrapolation method for measuring corrosion rates. Polarization curves showed that the three thiazole derivatives were of mixed-type inhibitors for mild steel corrosion in 0.5 M H₂SO₄ solution. EFM results were in agreement with other traditional chemical and electrochemical techniques used in corrosion rate measurements. Chemical and electrochemical measurements are consistent with computational study that APT is the most effective inhibitor among the tested thiazoles.     

Application of some ferrocene derivatives in the field of corrosion inhibition

Three ferrocene derivatives, namely 1,1′-diacetylferrocene (Diacetyl Fc), 1,1′-diformylferrocene (Diformyl Fc) and 2-benzimidazolythioacetylferrocene (BIM Fc) were synthesized and their inhibitive effects against mild steel corrosion in aerated 0.5 M H₂SO₄ and 1 M HCl solutions were evaluated. Corrosion measurements based on polarization resistance (R_p), potentiodynamic polarization curves and electrochemical impedance spectroscopy (EIS) indicate that Diacetyl Fc, in most cases, accelerates mild steel corrosion in HCl while Diformyl Fc and BIM Fc act as weak inhibitors. In H₂SO₄ solution, ferrocene derivatives show good inhibition performance. The efficiency of the inhibitors follows the order: BIM Fc > Diformyl Fc ? Diacetyl Fc. Adsorption of both Diacetyl Fc and Diformyl Fc obey Langmuir adsorption isotherm with very low value of free energy of adsorption ΔG^° for the Diformyl Fc (physisorption) while adsorption of BIM Fc follows that of Frumkin with high negative value of ΔG^° (chemisorption). Both Diformyl Fc and BIM Fc act as mixed-type inhibitors with predominant effect on the anodic dissolution of iron. Analysis of the polarization curves and impedance spectra indicates that charge transfer process mainly controls mild steel corrosion in H₂SO₄ solution without and with ferrocene compounds. The mechanism of corrosion inhibition or acceleration by ferrocene derivatives was discussed in the light of the molecular structure of the additives.     

Inhibitive and adsorption behaviour of carboxymethyl cellulose on mild steel corrosion in sulphuric acid solution

Chemical methods were used to assess the inhibitive and adsorption behaviour of carboxymethyl cellulose (CMC) for mild steel in H₂SO₄ solution at 30-60 °C. Results obtained show that CMC act as inhibitor for mild steel in H₂SO₄. The inhibition efficiency was found to increase with increase in CMC concentration but decreased with rise in temperature, which is suggestive of physical adsorption mechanism. The adsorption of the CMC onto the mild steel surface was found to follow Langmuir and Dubinin-Radushkevich adsorption isotherm models. The inhibition mechanism was further corroborated by the values of activation parameters obtained from the experimental data.     

Adsorption and inhibitive properties of some new Mannich bases of Isatin derivatives on corrosion of mild steel in acidic media

Adsorption of four derivatives of piperidinylmethylindoline-2-one on mild steel surface in 1 M HCl solution and its corrosion inhibition properties has been studied by a series of techniques, such as polarization, electrochemical impedance spectroscopy (EIS), weight loss and quantum chemical calculation methods. The values of activation energy (E_a) for mild steel corrosion and various thermodynamic parameters were calculated and discussed. Potentiodynamic polarization measurements showed that all inhibitors are mixed type. The degree of surface coverage was determined by using weight loss measurements and it was found that adsorption process of studied inhibitors on mild steel surface obeys Langmuir adsorption isotherm.     

Synergism between red tetrazolium and uracil on the corrosion of cold rolled steel in H2SO4 solution

The synergism between red tetrazolium (RT) and uracil (Ur) on the corrosion of cold rolled steel (CRS) in H₂SO₄ solution is first investigated by weight loss, potentiodynamic polarization, and atomic force microscope (AFM). Effects of inhibitor concentration (25-500 mg l⁻¹), temperature (20-50 °C), and acid concentration (1.0-5.0 M) on synergism are discussed systematically. The results reveal that RT has a moderate inhibitive effect, and its adsorption obeys the Freundlich adsorption isotherm. For Ur, it has a poor effect. However, incorporation of RT with Ur significantly improves the inhibition performance, and produces synergistic inhibition effect.     

2,2′-Dithiobis(3-cyano-4,6-dimethylpyridine): A new class of acid corrosion inhibitors for mild steel

The title compound (PyS)₂ has been synthesized and its inhibiting action on the corrosion of mild steel in 1-5 M H₂SO₄ solutions at 35-50 °C has been investigated by polarization resistance (R_p), polarization curves and electrochemical impedance spectroscopy (EIS). (PyS)₂ showed excellent performance and its efficiency did not affect either by increasing the acid concentration or rise of temperature. Polarization curves indicated that (PyS)₂ behaves mainly as anodic inhibitor in 1 M H₂SO₄ solutions and as a mixed-type inhibitor in 3 and 5 M H₂SO₄ solutions at different temperatures. Adsorption of (PyS)₂ on the steel surface followed Temkin’s adsorption isotherm with a very high negative value of the free energy of adsorption . The activation parameters of the corrosion process were calculated. EIS showed that the charge transfer controls the corrosion process in the uninhibited and inhibited solutions.     

Corrosion control of mild steel using 3,5-bis(4-methoxyphenyl)-4-amino-1,2,4-triazole in normal hydrochloric acid medium

The inhibition performance of the 3,5-bis(4-methoxyphenyl)-4-amino-1,2,4-triazole (4-MAT) on mild steel in normal hydrochloric acid medium (1 M HCl) at 30 °C was tested by weight loss, potentiodynamic polarisation and electrochemical impedance spectroscopy (EIS) techniques. This organic compound inhibits the acidic corrosion even at very low concentration, reaching a value of inhibition efficiency up to 98% at a concentration of 3 × 10⁻⁴ M. The results obtained from the different corrosion evaluation techniques are in good agreement. Polarisation curves indicate that 4-MAT is a mixed inhibitor, affecting both cathodic and anodic corrosion currents. Data, obtained from EIS measurements, were analyzed to model the corrosion inhibition process through appropriate equivalent circuit model, a constant phase element (CPE) has been used. The adsorption of 4-MAT on the steel surface, in 1 M HCl solution, obeys to Langmuir’s isotherm with a very high negative value of the free energy of adsorption ΔG°_ads (chemisorption). X-ray photoelectron spectroscopy (XPS) was carried out to establish the mechanism of corrosion inhibition of mild steel in 1 M HCl medium in the presence of 3,5-bis(4-methoxyphenyl)-4-amino-1,2,4-triazole (4-MAT).     

Triazolyl blue tetrazolium bromide as a novel corrosion inhibitor for steel in HCl and H2SO4 solutions

The inhibition effect of triazolyl blue tetrazolium bromide (TBTB) on the corrosion of cold rolled steel (CRS) in 1.0 M HCl and 0.5 M H₂SO₄ solution was investigated for the first time by weight loss, potentiodynamic polarization curves, and electrochemical impedance spectroscopy (EIS) methods. The results show that TBTB is a very good inhibitor, and is more efficiency in 1.0 M HCl than 0.5 M H₂SO₄. The adsorption of TBTB on CRS surface obeys Langmuir adsorption isotherm. Polarization curves reveal that TBTB acts as a mixed-type inhibitor in both acids.     

Synergistic inhibition behaviour of methylbenzyl quaternary imidazoline derivative and iodide ions on mild steel in H2SO4 solutions

The inhibition behaviour of 2-undecyl-1-ethylamino-1-methylbenzyl quaternary imidazoline (2UMQI) and KI on mild steel in 1.0 M H₂SO₄ solutions was investigated at 25 °C using electrochemical methods. The results indicated that 2UMQI inhibited the corrosion of mild steel and the extent of inhibition increased with 2UMQI concentrations. The inhibition action in the presence of 2UMQI is due to physical adsorption of 2UMQI. A mixed-inhibition mechanism is proposed for the inhibitive effects of 2UMQI. Inhibition efficiency of 2UMQI was enhanced by the addition of iodide ions. In the presence of KI, the potentials of unpolarization, E_u was observed and increased with KI concentration.     

Corrosion inhibition of mild steel in hydrochloric acid solution by some double Schiff bases

The inhibition effect of four double Schiff bases on the corrosion of mild steel in 2 M HCl has been studied by polarization, electrochemical impedance spectroscopy (EIS) and weight loss measurements. The inhibitors were adsorbed on the steel surface according to the Langmuir adsorption isotherm model. From the adsorption isotherm, some thermodynamic data for the adsorption process were calculated and discussed. Kinetic parameters activation such as E_a, ΔH∗, ΔS∗ were evaluated from the effect of temperature on corrosion and inhibition processes. Quantum chemical calculations have been performed and several quantum chemical indices were calculated and correlated with the corresponding inhibition efficiencies.