Poly(3‐octylthiophene) thermally treated as coating for corrosion protection of SS304 in sulfuric acid media

Poly(3‐octylthiophene) (P3OT) was synthesized by direct oxidation of the 3‐octylthiophene monomer using ferric chloride (FeCl₃) as an oxidant. Using the drop‐casting technique, P3OT coatings were deposited onto 304 type stainless steel electrodes. For the purpose of determining the effect of thermal annealing on the corrosion protection of stainless steel with P3OT coatings, the coated electrodes were thermally annealed for 30 h at two different temperatures, 55 and 100 °C. The corrosion behavior of P3OT coated stainless steel was investigated in 0.5 M sulfuric acid (H₂SO₄) at room temperature using potentiodynamic polarization curves (PPC), linear polarization resistance (LPR), and electrochemical impedance spectroscopy (EIS). The results indicated that the thermally treated P3OT coatings improved the corrosion resistance of the stainless steel in 0.5 M H₂SO₄. The best corrosion protection was obtained by the P3OT coating annealed at 100 °C. In order to study the temperature effect on the morphology of the coatings before and after the corrosive environment and compare it with corrosion protection, atomic force microscopy (AFM) and scanning electronic microscopy (SEM) were used.     

Study of the corrosion and microstructure with annealing conditions of a β-quenched HANA-4 alloy

The variation of microstructure and corrosion characteristics with the applied annealing conditions of a HANA-4 (Zr-1.5Nb-0.4Sn-0.2Fe-0.1Cr) alloy were studied by utilizing transmission electron microscopy and a corrosion test at 360 °C in a water environment. The samples were annealed at temperature ranges from 540 to 660 °C up to 16 h after β quenching at 1050 °C. The corrosion behaviour with the annealing conditions was divided into two groups following the second phase characteristics. The suitable annealing temperature to obtain good corrosion resistance in the HANA-4 alloy ranged from 570 to 600 °C.     

Optical properties of Se or S-doped hydrogenated amorphous silicon thin films with annealing temperature and dopant concentration

We report the effects of the thermal annealing and dopant concentration on the optical properties of Se or S-doped hydrogenated amorphous silicon thin films. The Se and S-doped a-Si:H (a-Si,Se:H and a-Si,S:H) thin films were prepared by glow discharge plasma enhanced chemical vapor deposition (GD-PECVD) on 7059 corning glass. The films were subsequently annealed in vacuum in the temperature range from 100 to 500 °C. Influence of doping and annealing was examined by means of optical transmission spectroscopy of the films in the wavelength range of 300-1100 nm taken at room temperature. The absorption coefficients and refractive indices decreased as the annealing temperature increased from 100 to 300 °C and then increased again as the annealing temperature further increased to 500 °C, while the highest bandgap was observed at 300 °C for all of the samples. For a given dopant concentration bandgap was observed to be higher in a-Si,S:H than a-Si,Se:H thin films.     

Corrosion behavior of iron-based alloys in the LiBr + ethylene glycol + H2O mixture

The corrosion resistance of 1018 carbon steel, 304 and 316 type stainless steels in the LiBr (55 wt.%) + ethylene glycol + H₂O mixture at 25, 50 and 80 °C has been studied using electrochemical techniques which included potentiodynamic polarization curves, electrochemical noise and electrochemical impedance spectroscopy techniques. Results showed that, at all tested temperature, the three steels exhibited an active-passive behavior. Carbon steel showed the highest corrosion rate, since both the passive and corrosion current density values were between two and four orders of magnitude higher than those found for both stainless steels. Similarly, the most active pitting potential values was for 1018 carbon steel. For 1018 carbon steel, the corrosion process was under a mixed diffusion and charge transfer at 25 °C, whereas at 50 and 80 °C a pure diffusion controlled process could be observed. For 316 type stainless steel, at 25 and 50 °C a species adsorption controlled process was observed, whereas at 80 °C a diffusion controlled mechanism was present. Additionally, at 25 °C, the three steels were more susceptible to uniform type of corrosion, whereas at 50 and 80 °C they were very susceptible to localized type of corrosion.     

Pitting corrosion behaviour of PM austenitic stainless steels sintered in nitrogen-hydrogen atmosphere

PM 304L and 316L stainless steel have been compacted at 400, 600 and 800 MPa and sintered in vacuum and in nitrogen-hydrogen atmosphere. Postsintered heat treatments (annealing solution and ageing at 375, 675 and 875 °C) have been applied. Pitting corrosion resistance has been studied using anodic polarization measurements and the ferric chloride test. Anodic polarization curves reveal that densities and atmospheres are relevant on anodic behaviour. Pitting resistance is higher for PM 316L and for higher densities and vacuum as sintered atmosphere. Ageing heat treatments at medium and high temperatures are detrimental to passivity although susceptibility to pitting corrosion barely changes. But heat treatments at 375 °C even show certain improvement in pitting corrosion resistance. The results were correlated to the presence of precipitates and mainly to the lamellar constituent which appears in some samples sintered in nitrogen-hydrogen atmosphere. The role of nitrogen on the samples sintered under nitrogen-hydrogen atmosphere and its relation to the microstructural features was described.     

A study of the corrosion behavior of gamma titanium aluminide in 3.5 wt% NaCl solution and seawater

Gamma titanium aluminide (γ-TiAl) was evaluated for corrosion resistance in 3.5% NaCl and seawater using potentiodynamic polarization and electrochemical impedance spectroscopy (EIS). Polarization plots indicate very low corrosion rates although in both electrolytes the control samples lost passivity at low polarization potentials. Surface modification treatments were employed by oxidizing the samples in air at 500 °C and 800 °C with the purpose of improving corrosion resistance. While the surface treatments rendered γ-TiAl passive in the polarization experiments in both electrolytes, EIS tests showed that the oxide formed at 800 °C was not protective. EEC models are proposed to explain the EIS results for the three surface conditions tested.     

The effect of 180 °C-annealing on the electrochemical behavior of nano-thick zinc-electroplated copper in aqueous solutions with different pH

The anodic polarization and a.c. impedance measurements of 4 nm- and 25 nm-zinc-electroplated copper specimens were conducted in aqueous solutions with four different pH-values. The nano-thick zinc-electroplated copper was tested after electroplating and annealing at 180 °C for 1, 2 and 3 h, respectively. The results showed that the open-circuit potential (OCP) of 25 nm-zinc electroplated copper shifted toward noble potential after annealing. A more noble OCP of 25 nm zinc-electroplated copper could be achieved when zinc plated copper was annealed at 180 °C up to 1 h. Similar change was found for 4 nm-zinc electroplated copper only in neutral and alkaline solutions. The a.c. impedance response of all nano-thick zinc-electroplated copper corresponded to two Randle’s circuits in series, in which the circuit measured in a high frequency region of their Nyquist diagrams revealed the electrochemical behavior of nano-thick zinc deposits. The charge transfer resistance of the nano-thick zinc electroplated copper was significantly raised after annealing at 180 °C when tested in pH 9.5 solution. Microstructures of the aforementioned nano-thick zinc electroplated copper were examined with cross-sectional TEM specimens. A distinct phase interface between zinc and copper was observed for as plated specimens, while alloying of zinc and copper at the interface was detected after annealing at 180 °C for 1 h. Electroplated zinc diffused into the copper foil during the 180 °C-annealing and the corrosion potential of the anodic polarization curve indicated the condition of the alloy surface. The annealing effect of 4 nm- and 25 nm-zinc electroplated copper specimens could be related to the results of electrochemical measurement.     

Microstructural evolution of coating-modified 3D C/SiC composites after annealing in wet oxygen at different temperatures

Two types of coating-modified 3D C/SiC, coated with CVD SiC/SiC/SiC (type I) and CVD SiC/amorphous-BC/SiC (type II), are subjected to a 14 vol.% H₂O/8 vol.% O₂/78 vol.% Ar atmosphere at 700, 1000 and 1200 °C up to 100 h. Microstructure and corrosion behaviour are investigated using a variety of characterization techniques. The type II shows a better oxidation resistance than type I during annealing at relatively low temperatures. Nevertheless, residual strength of the type I annealed above 1000 °C is enhanced by healing of many micron-sized defects. Interfacial bond strength of the composites is reasonably improved after annealing.     

Hydrothermal corrosion of TiAlN and CrN PVD films on stainless steel

Hydrothermal corrosion of thin TiAlN and CrN PVD films (of 3μm thickness) in 100 MPa water over a temperature range of 20-950 °C is compared to the behavior of TiN films over the same T-P conditions. Corrosion resistance increases in the sequence TiN → TiAlN → CrN. A FeTiO₃ (ilmenite) layer on the surface of the TiAlN film is almost chromium-free and provides protective properties up to 700 °C, whilst ülvospinel formation leads to spallation of oxide scale due to high level growth stresses. Formation of a very stable spinel scale on the surface of the CrN films provides long-term corrosion protection in 100 MPa water up to 800 °C. Nitride films on low-alloyed steel can substitute for expensive super alloy in wet air oxidation systems, with working temperatures up to 700 °C in the case of TiAlN, or 800 °C in the case of CrN coatings.     

The relation between microstructure and corrosion behavior of AZ80 Mg alloy following different extrusion temperatures

Cast AZ80 alloy was subjected to conventional extrusion pressing at 250 °C, 300 °C, and 350 °C. In order to characterize the changes in their microstructure a thorough study was done through various microscopy analyses including Optical Microscope, SEM, and TEM.Corrosion performance of each condition was investigated in 3.5% NaCl solution saturated with Mg(OH)₂ (pH ≈ 10.5) using immersion and AC and DC polarization tests. The local potential difference on the surface resulting from different compositions of second phase particles to the matrix was investigated using scanning Kelvin probe force microscopy (SKPFM) technique.The results show grain refinement by a factor of about 15-20 and obvious evidence of dynamic recrystallization were identified leading to the formation of nano-sized grains after the extrusion process.The corrosion resistance of cast AZ80 alloy drastically decreases after the thermo-mechanical processes and the main factor is high dependence on different phase rearrangements before and after the extrusion process, especially β phase. For the extrusion conditions, different corrosion resistances are attributable especially to dislocation rearrangement results by grain growth after dynamic recrystallization.     

High temperature corrosion properties of ionic liquids

The corrosion behaviour of several metals and metal alloys (copper, nickel, AISI 1018 steel, brass, Inconel 600) exposed to a typical ionic liquid, the 1-butyl-3-methyl-imidazolium bis-(trifluoromethanesulfonyl) imide, ([C₄mim][Tf₂N]), has been investigated by electrochemical and weight-loss methods. Corrosion current densities have been determined by extrapolation from Tafel plots and by polarization resistance measurements and 48 h immersion tests were performed at 150, 250, 275 and 325 °C. Room temperature results show low corrosion current densities (0.1-1.2 μA/cm²) for all the metals and alloys investigated. At 70 °C, the corrosion current for copper dramatically increases showing a strongly dependence on temperature. At 150 °C copper shows significant weight-loss while nickel, AISI 1018, brass and Inconel do not. At higher temperatures (?275 °C), the copper sample crumbles and localized corrosion occurs for the other metals and alloys.     

An electrochemical study of the effect of Li on the corrosion behavior of Ni3Al intermetallic alloy in molten (Li + K) carbonate

A study of the effect of lithium content (1, 3 and 5 wt.%) and heat treatment (400 °C during 144 h) on the corrosion behavior of Ni₃Al alloy has been carried out in a 62 mol.%Li₂CO₃-38 mol.%K₂CO₃ mixture at 650 °C using electrochemical techniques. Employed electrochemical techniques included potentiodynamic polarization curves, linear polarization resistance, LPR, electrochemical impedance spectroscopy, EIS, and electrochemical noise, measurements EN. Results have shown that the alloys exhibited an active-passive behavior regardless of the heat treatment. For alloys without heat treatment, the most corrosion resistant was the Ni₃Al base alloy, but when they were heat treated, the most corrosion resistant was the alloy containing 3%Li. EIS results showed that for short immersion tests, the corrosion process was under diffusion control, but for longer exposure times, the presence of a protective scale was evident. All the alloys were highly susceptible to a localized type of corrosion according to EN measurements and supported by SEM micrographs.     

Oxidation resistance and mechanical property of cosputtered quasi-amorphous Ta-Si-N films under vacuum rapid thermal annealing

The oxidation resistance and mechanical properties of Ta-Si-N films at high temperature are important issues for application. In this paper, quasi-amorphous Ta-Si-N thin films were fabricated by using reactive magnetron co-sputtering at different Si/Ta power ratios and nitrogen flow ratios (FN₂% = FN₂/(FAr + FN₂) × 100%). Vacuum rapid thermal annealing at 600-900 °C at 2.6 Pa was performed to investigate the oxidation resistance of films. At the higher Si/Ta power ratio and increased FN₂%, there is low oxygen fraction (O/(O + N) ≤ 0.2) of films at high annealing temperature which corresponds to benefit oxidation resistance. The crystalline δ-Ta₂O₅ phase was formed at 900 °C for all films. The islands of oxide were formed on the surface of films at low-Si-content (≤ 20 at.%) after 900 °C annealing. The hardness of all as-deposited Ta-Si-N films was between 16 and 24 GPa. The low-Si-content Ta-Si-N films has higher hardness than high-Si-content (≥ 20 at.%) ones due to lower fraction of soft amorphous SiN_x. The effect of annealing temperature on the correlation among process parameters, microstructure, phase transformation and hardness is discussed. The Ta-Si-N formed at 6 FN₂% and Si/Ta power ratio of 2/1 can be the best candidate for good oxidation resistance with appropriate mechanical property.     

Baking treatment effect on materials characteristics and electrochemical behavior of anodic film formed on AZ91D magnesium alloy

The composition and microstructure of the anodic films formed on AZ91D Mg alloy, with or without baking, were investigated. The associated corrosion behavior of the anodized alloy in 3.5 wt% NaCl solution was also examined using electrochemical impedance spectroscopy (EIS). The results show that MgO was the main component in the anodic film which also contained some Mg(OH)₂, Al₂O₃, Al(OH)₃, and MgAl₂O₄. Both the amorphous and crystalline forms of anodic film were identified. The degree of crystallinity depended on baking temperature, which increased with increasing temperature in the range of 50-250 °C. The amounts of MgO and Al₂O₃ increased as a result of a dehydration reaction. The polarization resistance of anodized Mg alloy was improved significantly by increasing the oxide content in the anodic film. An optimum value of polarization resistance of anodic film was obtained for the alloy baked at 150 °C for 2 h followed by air cooling.     

Annealing temperature effect on the corrosion parameters of autocatalytically produced Ni-P and Ni-P-Al2O3 coatings in artificial seawater

Ni-P and Ni-P-Al₂O₃ amorphous alloy coatings with 9.3 and 8.3 wt.% P respectively were obtained by autocatalytic deposition at 90 °C on carbon steel substrates. The effect of annealing temperature (100, 200, 300, 400 and 500 °C) upon the corrosion parameters of the coatings in artificial seawater with pH 5.0 and 8.1 at room temperature was evaluated by potentiodynamic polarisation and electrochemical impedance spectroscopy. It was found that deposits annealed at 400 and 500 °C presented an increase of the charge transfer resistance and negligible changes on samples annealed at lower temperature. Polarisation tests showed a charge transfer controlled anodic kinetics on both Ni-P and Ni-P-Al₂O₃ deposits and diffusion controlled cathodic reaction in artificial seawater at pH 5.0 and 8.1. The coatings did not present passive behaviour in the electrolytes and impedance measurements showed a single time constant for all cases with the lowest double layer capacitance (C_dl) for samples annealed at 400 and 500 °C. The best corrosion parameters were observed on Ni-P and Ni-P-Al₂O₃ coatings annealed at temperatures higher than 400 °C, which is the temperature where crystallisation of this kind of coatings takes place.     

Effect of temperature on the corrosion resistance and pitting behaviour of Alloy 31 in LiBr solutions

The corrosion resistance and pitting behaviour of Alloy 31, a high-alloyed austenitic stainless steel (UNS N08031), is studied in two heavy brine LiBr solutions (850 g/l) with and without corrosion inhibitor (lithium chromate) at different temperatures (25 °C, 50 °C, 75 °C and 100 °C) using electrochemical techniques. Cyclic potentiodynamic curves indicate that UNS N08031 is less pitting corrosion resistant and it reduces its repassivation properties as temperature increases. Comparison between the results obtained in LiBr solutions with and without inhibitor suggested a decrease in the inhibitor efficiency of lithium chromate at high temperatures.     

Electrochemical corrosion behaviour of nanotubular Ti-13Nb-13Zr alloy in Ringer’s solution

Nanotubular oxide layer formation was achieved on biomedical grade Ti-13Nb-13Zr alloy using anodization technique in 1 M H₃PO₄ + 0.5 wt.% NaF. The as-formed and heat treated nanotubes were characterized using SEM, XRD and TEM. Corrosion behaviour of the nanotubular alloy was investigated employing potentiodynamic and potentiostatic polarization. The alloy after nanotubular oxide layer formation exhibited significantly higher corrosion current density than the bare alloy. The lower corrosion resistance of the nanotubular alloy was suggested to be associated with the distinctly separated barrier oxide/concave shaped tube bottom interface. A heat treatment at 150 °C appreciably enhanced the corrosion resistance property.     

Microstructure and corrosion behaviour of pulsed plasma-nitrided AISI H13 tool steel

The effect of pulsed plasma nitriding temperature and time on the pitting corrosion behaviour of AISI H13 tool steel in 0.9% NaCl solutions was investigated by cyclic polarization. The pitting potential (E_pit) was found to be dependent on the composition, microstructure and morphology of the surface layers, whose properties were determined by X-ray diffraction and scanning electron microscopy techniques. The best corrosion protection was observed for samples nitrided at 480 °C and 520 °C. Under such experimental conditions the E_pit-values shifted up to 1.25 V in the positive direction.     

Oxidation resistance and corrosion behavior of hot-dip aluminized coatings on commercial-purity titanium

Aluminizing is an effective method to protect alloys from oxidation and corrosion. In this article, the microstructure, morphology, phase composition of the aluminized layers and the oxide films were investigated by SEM, EDS and X-ray diffraction. The high temperature oxidation resistance and electrochemical behavior of hot dip aluminizing coatings on commercial-purity titanium had been studied by cyclic oxidation test and potentiodynamic polarization technique. The results show that the reaction between the titanium and the molten aluminum leads to form an aluminum coating which almost has the composition of the aluminum bath. After diffusion annealing at 950 °C for 6 h, the aluminum coating transformed into a composite layer, which was composed of an inner layer and an outer layer. The inner layer was identified as Ti₃Al or Ti₂Al phase, and the outer layer was TiAl₃ and Al₂O₃ phase. The cyclic oxidation treatment at 1000 °C for 51 h shows that the oxidation resistance of the diffused titanium is 13 times more than the bare titanium. And the formation of TiAl₃, θ-Al₂O₃ and compact α-Al₂O₃ at the outer layer was thought to account for the improvement of the oxidation resistance at high temperature. However, the corrosion resistance of the aluminized titanium and the diffused titanium were reduced in 3.5 wt.% NaCl solution. The corrosion resistance of the aluminized titanium was only one third of bare titanium. Moreover, the corrosion resistance of the diffused titanium was far less than bare titanium.     

Effects of solution temperature on localized corrosion of high nickel content stainless steels and nickel in chromated LiBr solution

The potentiodynamic technique has been used to study the general and localized corrosion resistance of high-alloyed stainless steels (UNS N02031 and UNS R20033) and nickel (UNS N02205) at different temperatures (from 25 °C to 80 °C) in a heavy brine Lithium Bromide solution.The engineering question of concern is the compatibility of the LiBr fluid with the structural materials of refrigeration systems which use absorption technology. The results of potentiodynamic polarization studies indicate excellent corrosion resistance for stainless steels in LiBr solution at room temperature and no big differences at temperatures above 50 °C. In the temperature range of 25-80 °C, a linear relationship exists between logarithmic of corrosion rate and reciprocal of absolute temperature (Arrhenius plot). The linear plots showed that the mechanism of the corresponding passivation process is the same for the three investigated alloys, essentially due to the presence of nickel. Tests indicated that stainless steels UNS N02031 and UNS R20033 were the most suitable for use to be used in the construction of absorption units for refrigeration purposes.