A first quantitative XPS study of the surface films formed, by exposure to water, on Mg and on the Mg-Al intermetallics: Al3Mg2 and Mg17Al12

An XPS investigation was carried out of the surface films, formed by exposure to ultrapure water, on mechanically ground Mg and the two Mg-Al intermetallic compounds: Al₃Mg₂ and Mg₁₇Al₁₂. The mechanically ground Mg surface had a film of MgO at the Mg metal surface covered by a Mg(OH)₂ layer, formed by the reaction of the MgO with water vapour in the air. Upon immersion in ultrapure water, this film converted to a duplex film with an inner MgO layer next to the Mg metal and an external porous hydroxide layer. For both intermetallics, the XPS data is consistent with (i) preferential dissolution of Mg and (ii) a 10 nm thick film on the surface after immersion in ultrapure water; the film composition on Al₃Mg₂ was AlMg_1.4O_0.2(OH)_5.4 whilst on Mg₁₇Al₁₂ the composition was AlMg_2.5(OH)₈.     

Baking treatment effect on materials characteristics and electrochemical behavior of anodic film formed on AZ91D magnesium alloy

The composition and microstructure of the anodic films formed on AZ91D Mg alloy, with or without baking, were investigated. The associated corrosion behavior of the anodized alloy in 3.5 wt% NaCl solution was also examined using electrochemical impedance spectroscopy (EIS). The results show that MgO was the main component in the anodic film which also contained some Mg(OH)₂, Al₂O₃, Al(OH)₃, and MgAl₂O₄. Both the amorphous and crystalline forms of anodic film were identified. The degree of crystallinity depended on baking temperature, which increased with increasing temperature in the range of 50-250 °C. The amounts of MgO and Al₂O₃ increased as a result of a dehydration reaction. The polarization resistance of anodized Mg alloy was improved significantly by increasing the oxide content in the anodic film. An optimum value of polarization resistance of anodic film was obtained for the alloy baked at 150 °C for 2 h followed by air cooling.     

Analysis of the electrochemical reaction behavior of alloy AZ91 by EIS technique in H3PO4/KOH buffered K2SO4 solutions

The EIS technique was used to analyze the electrochemical reaction behavior of Alloy AZ91 in H₃PO₄/KOH buffered K₂SO₄ solution at pH 7. The corrosion resistance of Alloy AZ91 was directly related with the stability of Al₂O₃ · xH₂O rich part of the composite oxide/hydroxide layer on the alloy surface. The break down of the oxide layer was estimated to occur mainly on the matrix solid solution phase in Alloy AZ91. The mf capacitive loop arose from the relaxation of mass transport in the solid oxide phase in the presence of Al₂O₃ · xH₂O rich part and from Mg⁺ ion concentration within the broken area in the absence of Al₂O₃ · xH₂O rich part in the composite oxide structure on the alloy surface. The lf inductive loop had tendency of disappear when the dissolution rate of the alloy decreased as a result of the formation of the protective oxide layer.     

Self-healing mechanism of a protective film prepared on a Ce(NO3)3-pretreated zinc electrode by modification with Zn(NO3)2 and Na3PO4

Self-healing mechanism of a protective film against corrosion of zinc at scratches in an aerated 0.5 M NaCl solution was investigated by polarization measurements, X-ray photoelectron spectroscopy (XPS) and electron-probe microanalysis (EPMA). The film was prepared on a zinc electrode by treatment in a Ce(NO₃)₃ solution and addition of aqueous solutions containing 9.98 or 19.9 μg/cm² of Zn(NO₃)₂ · 6H₂O and 55.2 μg/cm² of Na₃PO₄ · 12H₂O. After the coated electrode was scratched with a knife-edge crosswise and immersed in the NaCl solution for many hours, polarization measurements, observation of pit formation at the scratches, XPS and EPMA were carried out. This film was remarkably protective and self-healing against zinc corrosion on the scratched electrode. The cathodic and anodic processes of zinc corrosion were markedly suppressed by coverage of the surface except for scratches with a thin Ce₂O₃ layer containing a small amount of Ce⁴⁺ and the surface of scratches with a layer composed of Zn₃(PO₄)₂ · 4H₂O, Zn(OH)₂ and ZnO mostly.     

The influence of CO2, AlCl3 · 6H2O, MgCl2 · 6H2O, Na2SO4 and NaCl on the atmospheric corrosion of aluminum

The influence of salt deposits on the atmospheric corrosion of high purity Al (99.999%) was studied in the laboratory. Four chloride and sulfate-containing salts, NaCl, Na₂SO₄, AlCl₃ · 6H₂O and MgCl₂ · 6H₂O were investigated. The samples were exposed to purified humid air with careful control of the relative humidity (95%), temperature (22.0 °C), and air flow. The concentration of CO₂ was 350 ppm or <1 ppm and the exposure time was four weeks. Under the experimental conditions all four salts formed aqueous solutions on the metal surface. Mass gain and metal loss results are reported. The corroded surfaces were studied by ESEM, OM, AES and FEG/SEM equipped with EDX. The corrosion products were analyzed by gravimetry, IC and grazing incidence XRD. In the absence of CO₂, the corrosivity of the chloride salts studied increases in the order MgCl₂ · 6H₂O < AlCl₃ · 6H₂O < NaCl. Sodium chloride is very corrosive in this environment because the sodium ion supports the development of high pH in the cathodic areas, resulting in alkaline dissolution of the alumina passive film and rapid general corrosion. The low corrosivity of MgCl₂ · 6H₂O is explained by the inability of Mg²⁺ to support high pH values in the cathodic areas. In the presence of carbon dioxide, the corrosion induced by the salts studied exhibit similar rates. Carbon dioxide strongly inhibits aluminum corrosion in the presence of AlCl₃ · 6H₂O and especially, NaCl, while it is slightly corrosive in the presence of MgCl₂ · 6H₂O. The corrosion effects of CO₂ are explained in terms of its acidic properties and by the precipitation of carbonates. In the absence of CO₂, Na₂SO₄ is less corrosive than NaCl. This is explained by the lower solubility of aluminum hydroxy sulfates in comparison to the chlorides. The average corrosion rate in the presence of CO₂ is the same for both salts. The main difference is that sulfate is less efficient than chloride in causing pitting of aluminum in neutral or acidic media.     

Oxidation performance of Mo3Si with Al additions

The Mo₃Si alloys with different aluminum contents were fabricated by the arc-melting and drop-casting technique, heat treated and then exposed to air at 700, 800, 900 and 1000 °C in order to assess their oxidation behavior. Line scan studies led to the assumption that the oxide scale thermally grown at 1000 °C was composed of SiO₂ which was located closer to the alloy matrix and Al₂O₃ around the outer surface of the oxidized sample, while the Mo oxide volatilized at this oxidation temperature. The results also showed that the unalloyed sample (Mo₃Si) underwent a pest reaction in a short time of exposure, while the sample with 16 at.% Al exhibited the best oxidation behavior, which could be attributed to the formation of SiO₂ and Al₂O₃ in the oxide scale.     

Sulphidation/oxidation behaviour of TiAlCr and Al2Au coated Ti45Al8Nb alloy at 750 °C

In this paper, we present the sulphidation/oxidation behaviour of a Ti45Al8Nb (at%) alloy coated with different protective surface films. Two intermetallic coatings are considered; TiAlCr and Al₂Au deposited by physical vapour deposition. The coated alloy was subjected to a H₂/H₂S/H₂O yielding pS₂ - 10⁻¹ Pa and pO₂ - 10⁻¹⁸ Pa potentials at 750 °C for up to 1000 h. The corrosion kinetics were determined by means of discontinuous gravimetry and the as-received and exposed samples were characterised using scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDX) and X-ray diffraction analysis (XRD). The materials showed the development of a multilayered structure. In the case of the TiAlCr coated Ti45Al8Nb - base alloy, Al₂O₃, TiO₂ and Cr₂S₃ developed. For the Al₂Au coated Ti45Al8Nb samples an Al₂O₃ scale containing TiO₂ nodules was observed at the surface.     

In situ growth of Mg–Al hydrotalcite conversion film on AZ31 magnesium alloy

In situ growth of Mg–Al hydrotalcite conversion film on AZ31 alloy has been developed by a two-step method. The characteristics of the films were investigated by X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), scanning electronic microscope (SEM) observation, electrochemical and immersion tests. The film formation process was proposed based on the open circuit potential (OCP) measurements and surface analysis. A precursor film with network cracks is first formed and then this film is transformed into a compact and uniform hydrotalcite (Mg₆Al₂(OH)₁₆CO₃·4H₂O) film after the post treatment. This dense Mg–Al hydrotalcite film can provide effective protection to the AZ31 alloy.     

Assessment of the surface state behaviour of Al71Cu10Fe9Cr10 and Al3Mg2 complex metallic alloys in sliding contacts

Electrochemical measurements and friction measurements during continuous and intermittent unidirectional sliding tests are used to monitor and to evaluate the surface characteristics of two types of metallic materials characterized by a huge unit cell, namely Al₇₁Cu₁₀Fe₉Cr₁₀ and Al₃Mg₂. The modification of the surface characteristics results from the periodic mechanical removal of a surface film during sliding, and the subsequent (electro)chemical re-growth of a surface film in-between successive sliding contacts. Al₇₁Cu₁₀Fe₉Cr₁₀ and Al₃Mg₂ materials were tested in a phosphate buffer solution pH 7 at 25 °C to compare their depassivation and subsequent repassivation behaviour. The Al₃Mg₂ material was also tested in a 0.1 M KOH solution pH 13 and 25 °C to reveal the role of constituting metallic elements on the surface film formation. The effect of film formation and removal on the coefficient of friction recorded during unidirectional sliding is discussed.     

Microstructural and mechanical properties of Al-Mg/Al2O3 nanocomposite prepared by mechanical alloying

The effect of milling time on the microstructure and mechanical properties of Al and Al-10 wt.% Mg matrix nanocomposites reinforced with 5 wt.% Al₂O₃ during mechanical alloying was investigated. Steady-state situation was occurred in Al-10Mg/5Al₂O₃ nanocomposite after 20 h, due to solution of Mg into Al matrix, while the situation was not observed in Al/5Al₂O₃ nanocomposite at the same time. For the binary Al-Mg matrix, after 10 h, the predominant phase was an Al-Mg solid solution with an average crystallite size 34 nm. Up to 10 h, the lattice strain increased to about 0.4 and 0.66% for Al and Al-Mg matrix, respectively. The increasing of lattice parameter due to dissolution of Mg atom into Al lattice during milling was significant. By milling for 10 h the dramatic increase in microhardness (155 HV) for Al-Mg matrix nanocomposite was caused by grain refinement and solid solution formation. From 10 to 20 h, slower rate of increasing in microhardness may be attributed to the completion of alloying process, and dynamic and static recovery of powders.     

Hot corrosion behaviour of Ni3Al in sulphate-chloride mixtures in the atmosphere

Hot corrosion of Ni₃Al intermetallic compound in the presence of sulphate-chloride mixtures was studied. A comminuted Ni₃Al mixed with NaCl-Na₂SO₄, NaCl-Li₂SO₄, LiCl-Na₂SO₄, LiCl-Li₂SO₄ additions was oxidized in the air up to 1000 °C with linearly increasing temperature and isothermally within the temperature range of 500-700 °C. The corrosion process was observed by thermogravimetric method using Mettler thermoanalyzer.The experiments indicated that LiCl (∼10 wt.%)-Li₂SO₄ mixture was the most corrosive agent. It was also found that by addition of MgO the corrosion of Ni₃Al was reduced. Phase composition of the corrosion products was established by X-ray diffraction analysis; there were detected Al₂O₃, Al₂S₃, NaAlO₂ (or LiAlO₂) as intermediate products, nickel sulphides, NiO and NiAl₂O₄. NiAl₂O₄ spinel was formed only at the highest temperatures, while at lower temperatures alumina was present instead of spinel.Hot corrosion behaviour of Ni₃Al in sulphate-chloride mixtures in air atmosphere.     

Oxidation of Cr2AlC at 1300 °C in air

High purity, dense Cr₂AlC compounds were synthesized via a powder metallurgical route, and their oxidation behavior was investigated at 1300 °C in air for up to 336 h. A thin external oxide layer formed, which consisted primarily of not Cr₂O₃ but Al₂O₃. Since Al was consumed to produce the Al₂O₃, Al-depletion and Cr-enrichment occurred underneath the Al₂O₃ layer. This led to the formation of a Cr₇C₃ layer containing voids. These grew during oxidation, eventually destroying the Cr₇C₃ layer formed on the unoxidized Cr₂AlC matrix.     

The nature of the third-element effect in the oxidation of Fe-xCr-3 at.% Al alloys in 1 atm O2 at 1000 °C

The oxidation of an Fe-Al alloy containing 3 at.% Al and of four ternary Fe-Cr-Al alloys with the same Al content plus 2, 3, 5 or 10 at.% Cr has been studied in 1 atm O₂ at 1000 °C. Both Fe-3Al and Fe-2Cr-3Al formed external iron-rich scales associated with an internal oxidation of Al or of Cr+Al. The addition of 3 at.% Cr to Fe-3Al was able to stop the internal oxidation of Al only on a fraction of the alloy surface covered by scales containing mixtures of the oxides of the three alloy components, but not beneath the iron-rich oxide nodules which covered the remaining alloy surface. Fe-5Cr-3Al formed very irregular external scales where areas covered by a thin protective oxide layer alternated with others covered by thick scales containing mixtures of the oxides of the three alloy components, undergrown by a thin layer rich in Cr and Al, while internal oxidation was completely absent. Conversely, Fe-10Cr-3Al formed very thin, slowly-growing external Al₂O₃scales, providing an example of third-element effect (TEE). However, the TEE due to the Cr addition to Fe-3Al was not directly associated with a prevention of the internal oxidation of Al, but rather with the inhibition of the growth of external scales containing iron oxides. This behavior has been interpreted on the basis of a qualitative oxidation map for ternary Fe-Cr-Al alloys taking into account the existence of a complete solid solubility between Cr₂O₃ and Al₂O₃.     

Corrosion resistance of dilute CuMg alloys at elevated temperature

In comparison with CuAl (Al: 0.2 and 0.5 wt.%) alloys, corrosion resistance (CR) of CuMg (Mg: 0.12 and 0.34 wt.%) alloys was studied at 673-1173 K in atmospheric O₂. All the samples were pre-annealed at 873 K in atmospheric H₂. The CR of CuMg alloys at 673-973 K is improved in contrast to a pure Cu but much poorer than that of CuAl alloys, while the improvement can hardly be observed for CuMg alloys at and above 1073 K, which is similar to CuAl alloys. The poorer CR of CuMg alloys compared with that of CuAl alloys at 673-973 K is largely attributed to the incorporation of Cu in the MgO surface layer and the low Pilling-Bedworth ratio of CuMg-O system smaller than unity, and the vanishing of CR for CuMg alloys at and above 1073 K is ascribed to the instability of the MgO layer at the Cu₂O/CuMg interface.     

Oxidation and corrosion of silicon nitride ceramics with different sintering additives at 1200 and 1500 °C in air, water vapour, SO2 and HCl environments - A comparative study

The effect of different sintering additives on the high temperature oxidation and corrosion behaviour of silicon nitride based ceramics was investigated. Comparative tests were conducted at 1200 and 1500 °C in air, in water vapour, and with the highly corrosive gases HCl and SO₂. Si₃N₄ was prepared with MgO, Al₂O₃, Y₂O₃ and Al₂O₃ + Y₂O₃ sintering additives. Hot pressed discs were tested for a total time of up to 128 h. The electrically conductive ceramic composites Si₃N₄ + TiN and Si₃N₄ + MoSi₂ were also tested under the same conditions. The effects that the different corrosion environments have on the different ceramics are presented. SEM studies of the oxidised ceramics show the direct transformation of Si₃N₄ grains into SiO₂ through a reaction interface layer.     

Corrosion behaviour of magnesium/aluminium alloys in 3.5 wt.% NaCl

Corrosion behaviour of commercial magnesium/aluminium alloys (AZ31, AZ80 and AZ91D) was investigated by electrochemical and gravimetric tests in 3.5 wt.% NaCl at 25 °C. Corrosion products were analysed by scanning electron microscopy, energy dispersive X-ray analysis and low-angle X-ray diffraction. Corrosion damage was mainly caused by formation of a Mg(OH)₂ corrosion layer. AZ80 and AZ91D alloys revealed the highest corrosion resistance. The relatively fine β-phase (Mg₁₇Al₁₂) network and the aluminium enrichment produced on the corroded surface were the key factors limiting progression of the corrosion attack. Preferential attack was located at the matrix/β-phase and matrix/MnAl intermetallic compounds interfaces.     

Al2O3-ZrO2 mixed oxide composite incorporated aluminium rich zinc coatings for high wear resistance

Corrosion resistance and wear resistance are the two important parameters for high performance of zinc galvanic coating. In the present work, the improvement of these two characteristics was achieved by the incorporation of Al₂O₃-ZrO₂ mixed oxide composite in the coating. Al₂O₃-ZrO₂ mixed oxide composite was synthesized from ZrOCl₂·8H₂O. Aluminium rich zinc coatings with high sliding wear resistance was developed from a galvanic bath containing the mixed oxide. Based on the performance of the coating during physicochemical and electrochemical characterization, the concentration of mixed oxide composite in the bath was optimized as 0.50 wt% Al₂O₃-0.50 wt% ZrO₂. While rich in Al-metal content in the coating caused high corrosion resistance, the incorporation of the mixed oxide improved structural characteristics of the coating resulting in high wear resistance also. The coating was nonporous in nature and even the interior layers had high stability. The coatings have potential scope for high industrial utility.     

Bulk WC-Al2O3 composites prepared by spark plasma sintering

WC and WC-Al₂O₃ materials without metallic binder addition were densified by spark plasma sintering in the range of 1800-1900 °C. The densification behavior, phase constitution, microstructure and mechanical properties of pure WC and WC-Al₂O₃ composite were investigated. The addition of Al₂O₃ facilitates sintering and increases the fracture toughness of the composites to a certain extent. An interesting phenomenon is found that a proper content of Al₂O₃ additive helps to limit the formation of W₂C phase in sintered WC materials. The pure WC specimen possesses a hardness (HV₁₀) of 25.71 GPa, fracture toughness of 4.54 MPa·m^1/2, and transverse fracture strength of 862 MPa, while those of WC-6.8 vol.% Al₂O₃ composites are 24.48 GPa, 6.01 MPa·m^1/2, and 1245 MPa respectively. The higher fracture toughness and transverse fracture strength of WC-6.8 vol.% Al₂O₃ are thought to result from the reduction of W₂C phase, the crack-bridging by Al₂O₃ particles and the local change in fracture mode from intergranular to transgranular.     

Role of Al2O3 layer in oxidation resistance of Cu-Al dilute alloys pre-annealed in H2 atmospheres

Copper was alloyed with small amounts of Al (0.2, 0.5, 1.0 and 2.0 mass%) to improve the oxidation resistance. Copper (6 N) and the Cu-Al alloys were oxidized at 773-1173 K in 0.1 MPa oxygen atmosphere after hydrogen annealing at 873 K. Continuous very thin Al₂O₃ layers were formed on the surface of all Cu-Al dilute alloys during the hydrogen annealing. Oxidation resistance of Cu-Al alloys was improved especially for Cu-2.0Al at 773-973 K, while it decreases on increasing the oxidation temperature. Cu-Al alloys followed the parabolic rate law at 1173 K, but most of other cases do not at and below 1073 K. Oxidation resistance for Cu-Al alloys was found relevant to the maintenance of the thin Al₂O₃ layer at the Cu₂O/Cu-Al alloy interface.     

The protective surface film formed on molten ZK60 magnesium alloy in 1,1,1,2-tetrafluoroethane/air atmospheres

The composition, microstructure and growth kinetics of the surface film formed on molten ZK60 magnesium alloy in 1,1,1,2-tetrafluoroethane/air mixture were investigated by using SEM, EDS, XRD, XPS and TG. The results show that the film formed in 0.01% 1,1,1,2-tetrafluoroethane/air was non-protective, and its phase composition changed with melt temperature. At 760 °C, the film was mainly composed of MgO and some MgF₂ and ZrO₂, whereas at 660 °C it consisted mainly of MgO and Mg₃N₂. The film formed in air containing 0.1% 1,1,1,2-tetrafluoroethane or higher was comprised of MgF₂ and C with small amounts of MgO, and it was protective.