The effect of molybdenum on the corrosion behaviour of the high-entropy alloys Co1.5CrFeNi1.5Ti0.5Mox in aqueous environments

The purpose of this study is to investigate the electrochemical properties of the Co_1.5CrFeNi_1.5Ti_0.5Mo_x high-entropy alloys in three aqueous environments which simulate acidic, marine, and basic environments at ambient temperature (∼25 °C). The potentiodynamic polarisation curves of the Co_1.5CrFeNi_1.5Ti_0.5Mo_x alloys, obtained in aqueous solutions of H₂SO₄ and NaOH, clearly revealed that the corrosion resistance of the Mo-free alloy was superior to that of the Mo-containing alloys. On the other hand, the lack of hysteresis in cyclic polarisation tests and SEM micrographs confirmed that the Mo-containing alloys are not susceptible to pitting corrosion in NaCl solution.     

Effect of surface finishing of a Zr-based bulk metallic glass on its corrosion behaviour

Zr-based metallic glasses passivate spontaneously, but exhibit also a certain pitting susceptibility. On the example of the Zr₅₉Ti₃Cu₂₀Al₁₀Ni₈ alloy studied in 0.01 M Na₂SO₄ + x M NaCl (x = 0-0.1) electrolytes it is demonstrated that the surface finishing state and the pre-exposure conditions can significantly influence the free corrosion and anodic polarisation behaviour. Mechanical fine-polishing procedures can lead to extremely smooth topographies but also to Cu enrichment at the surface. This yields a pronounced Cu dissolution at low anodic polarisation prior to stable passivity and increases the pitting initiation susceptibility as compared to mechanically ground surface states.     

Atmospheric corrosion of field-exposed AZ31 magnesium in a tropical marine environment

Corrosion behavior of AZ31 magnesium in tropical marine atmosphere was investigated. Chloride ions deposition rate played an important role in the corrosion process, which resulted in an obvious fluctuation of the corrosion rate. The corrosion was initiated from pitting corrosion and then evolved into general corrosion as the exposure time extended. Mg₅(CO₃)₄(OH)₂·xH₂O was the dominate products during the whole exposure periods. The products on the specimens weathered for 1, 6 and 12 months slightly suppressed the corrosion process, while that generated after 24 months of exposure exhibited good protective ability against further corrosion attacks.     

Effect of the aluminium content of AlxCrFe1.5MnNi0.5 high-entropy alloys on the corrosion behaviour in aqueous environments

High-entropy alloys (HEAs) are a newly developed family of multi-component alloys. The potentiodynamic polarization and electrochemical impedance spectroscopy of the Al_xCrFe_1.5MnNi_0.5 alloys, obtained in H₂SO₄ and NaCl solutions, clearly revealed that the corrosion resistance increases as the concentration of aluminium decreases. The Al_xCrFe_1.5MnNi_0.5 alloys exhibited a wide passive region, which extended >1000 mV in acidic environments. The Nyquist plots of the Al-containing alloys had two capacitive loops, which represented the electrical double layer and the adsorptive layer. SEM micrographs revealed that the general and pitting corrosion susceptibility of the HEAs increased as the amount of aluminium in the alloy increased.     

Corrosion product formation on Zn55Al coated steel upon exposure in a marine atmosphere

The formation of corrosion products on Zn55Al coated steel has been investigated upon field exposures in a marine environment. The corrosion products consisted mainly of zinc aluminium hydroxy carbonate, Zn_0.71Al_0.29(OH)₂(CO₃)_0.145·xH₂O, zinc chloro sulfate (NaZn₄(SO₄)Cl(OH)₆·6H₂O), zinc hydroxy chloride, Zn₅(OH)₈Cl₂·H₂O and zinc hydroxy carbonate, Zn₅(OH)₆(CO₃)₂ were the first three phases were formed initially while zinc hydroxy carbonate Zn₅(OH)₆(CO₃)₂ was formed after prolonged exposure in more corrosive conditions. The initial corrosion product formation was due to selective corrosion of the zinc rich interdendritic areas of the coating resulting in a mixture of zinc and zinc aluminium corrosion products.     

Effect of atmospheric pollutants on the corrosion of high power electrical conductors - Part 2. Pure copper

The research work performed during this study was simultaneously followed with another one published in this journal as Part I. A1 and 6201 A1 alloy. Its aim was to reveal a comparative picture of the joint effect of marine and industrial atmospheric pollutants on the corrosion resistance of wire metals employed for electric transmission conductors. Weight loss after 4, 11, 16 and 24 months exposure was determined and morphology of the attack analysed through SEM-ESEM-EDX. Cu corrosion products showed higher protectiveness than those of Al in marine sites for the lowest [Cl⁻] and in marine-industrial atmospheres even for the highest SO₂ contents. Respect to marine sites where [Cl⁻] was higher than [SO₂] Cu was more susceptible than A1.     

Measurements of pitting corrosion currents of zinc in near neutral media

Using a simple model cell the susceptibility of the zinc electrode to pitting corrosion by SO₄²⁻, SO₃²⁻, S₂O₃²⁻ and S²⁻ anions were examined in naturally aerated carbonate solutions. It was found that, pitting started after an induction period, τ, which depended on the type and concentration of the aggressive and passivating anions. The pitting corrosion current increased with time until steady state values were attained. These values depended on both the type and the concentration of the passivating and pitting anions. For the same concentration of the passivating anions, the corrosion current varied with the concentration of the aggressive anion according to the relation: logi_pit.=a₁+b₁logC_agg. At a constant concentration of the aggressive anion, the corrosion current varied with the concentration of the passivating anions according to: logi_pit.=a₂−b₂logC_pass. The constants a₁ (a₂) and b₁ (b₂) were determined for all the systems studied. From the values of a₁ the corrosivity of the sulphur-containing anions is found to decrease in the order SO₄²⁻>SO₃²⁻>S₂O₃²⁻>S²⁻.     

Studies on the initial stages of zinc atmospheric corrosion in the presence of chloride

A four-year exposure program was carried out in Taiwan in which 23 test sites with different climatic and pollution conditions were chosen and evaluated according to ISO standards 9223-9226. Examination of the results indicated that most of the tests sites were very corrosive to zinc specimens and there was a severe white rust problem for freshly galvanized items stored in high humidity outdoors environments. In addition, the initial stages of zinc atmospheric corrosion in the presence of chloride were studied quantitatively in a non-aqueous electrolyte (methanol) using ex situ electrochemical impedance spectroscopy (EIS) to determine polarization resistance (R_p). The samples were exposed to the synthetic atmospheres with careful controlled relative humidity, temperature, and contaminating salts. It was observed that a change of R_p was accompanied by a change in the corrosion product on the zinc surface, and that the R_p increased with relative humidity (RH) during pre-exposure. Furthermore, the corrosion products of zinc were analyzed qualitatively by grazing-angle X-ray diffraction (XRD) and Fourier transform infrared (FTIR) spectroscopy. Zinc hydroxycarbonate (Zn₅(CO₃)₂(OH)₆) and zinc oxide (ZnO) in this surface layer were found to provide protection against chloride contaminants.     

A newly synthesized glycine derivative to control uniform and pitting corrosion processes of Al induced by SCN anions - Chemical, electrochemical and morphological studies

A newly synthesized glycine derivative (termed GlyD), 2-(4-(dimethylamino)benzylamino)acetic acid hydrochloride, was used to inhibit uniform and pitting corrosion processes of Al in 0.50 M KSCN solutions (pH 6.8) at 25 °C. For uniform corrosion inhibition study, Tafel extrapolation, linear polarization resistance and impedance methods were used, complemented with SEM examinations. An independent method of chemical analysis, namely ICP-AES (inductively coupled plasma atomic emission spectrometry) was also used to test validity of corrosion rate measured by Tafel extrapolation method. GlyD inhibited uniform corrosion, even at low concentrations, reaching a value of inhibition efficiency up to 97% at a concentration of 5 × 10⁻³ M. Results obtained from the different corrosion evaluation techniques were in good agreement. This new synthesized glycine derivative was also used to control pit nucleation and growth on the pitted Al surface based on cyclic polarization, potentiostatic and galvanostatic measurements. The pitting potential (E_pit) and the repassivation potential (E_rp) increased by the addition of GlyD. Thus GlyD suppressed pit nucleation and propagation. Nucleation of pit was found to take place after an incubation time (t_i). The rate of pit nucleation and growth decreased with increase in inhibitor concentration. Morphology of pitting was also studied as a function of the applied anodic potential and solution temperature. Cross-sectional view of pitted surface revealed the formation of large distorted hemispherical and narrow deep pits. GlyD was much better than Gly in controlling uniform and pitting corrosion processes of Al in these solutions.     

Changes in corrosion rates in atmospheres with changing corrosivity

Abstract

This paper presents a study on the atmospheric corrosion of carbon steels, zinc, copper and aluminium in the industrial atmosphere. Trends representative for Central Europe are evaluated on the results for the Czech test site Kopisty. The climatic data and levels of pollutants, namely SO₂, have been measured, collected and analysed over 25 years. The corrosion rate of structural metals is significantly affected by SO₂ and the metals quickly react to the decrease of SO₂. The corrosion of both newly exposed metals and surfaces formerly exposed to polluted environments slowed when SO₂ pollution in the atmosphere was reduced. The study does not reflect the effects in atmospheric corrosion systems with dominating chloride influences (marine and marine–industrial atmospheres). The chemical composition and morphology of the corrosion product layers of zinc, copper and aluminium are presented and compared. The comparison of the corrosion rates and corrosion product compositions of zinc after 1, 20 and 100 years of exposure is presented.     

Environmental factors affecting the corrosion behavior of reinforcing steel III. Measurement of pitting corrosion currents of steel in Ca(OH)2 solutions under natural corrosion conditions

Using a simple electrolytic cell, the pitting corrosion current of reinforcing steel is measured in Ca(OH)₂ solutions in presence of chloride and sulfate as aggressive ions. Pitting corrosion current starts to flow after an induction period which depends on the concentration of both the aggressive and the passivating anions. The pitting corrosion current densities reach steady-state values which depend also on the type and concentration of the corrosive and passivating anions. The corrosive action of the aggressive species decreased in the order: SO₄²⁻ > Cl⁻. Corrosion of the steel is found to be governed by a single electron transfer reaction. Raising the temperature decreases the induction period associated with pit initiation and increases the corrosion current associated with pit propagation. From Arrhenius plots, the activation energies for both pit initiation and pit propagation in presence of chloride and sulfate ions are calculated.     

Comparative investigation into the corrosion of different bronze alloys suitable for outdoor sculptures

Several bronze alloys, suitable for production of outdoor sculptures, were developed in the frame of the European project “Eurocare-Bronzart”. The elemental composition of the alloys was searched to fulfil specific criteria such as: reduction of lead content, good resistance toward corrosion and aesthetic characteristics conformable to artistic purposes. After metallurgical characterization, the resistance toward corrosion was evaluated in artificial environments. Ageing experiments were performed in a salt spray cabinet and in a climatic chamber in the presence of a controlled concentration of SO₂. The Thin Layer Activation (TLA) method was applied to calculate the thickness loss of activated specimens exposed to artificial corrosive atmospheres. After artificial ageing experiments the surface of the materials was investigated by SEM-EDS techniques.The bronze alloys containing different percentage of nickel showed the best properties of resistance toward corrosion.     

Differences between corrosion products formed on copper exposed in Tokyo in summer and winter

We analyzed the copper corrosion products that formed during a month in summer and a month in winter at three sites in Tokyo using several analytical techniques. The X-ray diffraction patterns revealed that cuprite Cu₂O and posnjakite Cu₄SO₄(OH)₆·H₂O formed on copper exposed in summer. By contrast, only cuprite was found in winter exposed copper. The X-ray fluorescence results indicated that the amounts of sulfur and chlorine on the copper plates exposed in summer were much greater than those in winter. This could be explained by the change in particulate sulfate and sea salt concentrations. Depth profiling analysis by Auger electron spectroscopy revealed that the oxide layer formed in summer was thicker than that in winter. This difference in oxide layer thickness could have been due to the differences in temperature, relative humidity, and the amount of sulfur and chlorine on the copper plate.     

Corrosion behaviour of aluminium in copper containing environment

Corrosion behaviour of pure aluminium galvanically connected to metallic copper or in the presence of Cu²⁺ ions was investigated by electrochemical measurements in Na₂SO₄ and Na₂SO₄ + NaCl test solutions. It has been found that in aerated Cl⁻ ion containing solutions pitting corrosion of aluminium emerged immediately, while in the absence of oxygen this process was less violent. Effect of passivating pre-treatment of aluminium surface on corrosion behaviour Cu-Al bimetallic system is also demonstrated.     

Study of the electrochemical behaviour of nanocrystalline zinc by statistical methods

Pulse electrodeposition was used to synthesize nanocrystalline (NC) zinc coatings from citric acid bath. The electrochemical behaviour of the NC zinc coatings was investigated by using potentiostatic and potentiodynamic polarization methods in 0.5 mol/L NaCl (pH = 12) solution and compared with that of cast zinc. Pitting corrosion behaviour was characterized by pitting potential, induction time and stable pit growth rate which were analyzed according to statistical method. The results showed that nanocrystallization increased the sensitivity of E_pit refer to potential sweep velocity, changed the type of the pit generation from B1 (parallel) to B2 (series), accelerated the pitting initiation process and inhibited the stable pit growth process of NC zinc.     

Microbially influenced corrosion of zinc and aluminium - Two-year subjection to influence of Aspergillus niger

Aspergillus niger. Tiegh., a filamentous ascomycete fungus, was isolated from the metal samples exposed to marine, rural and urban sites in Lithuania. Al and Zn samples were subjected to two-year influence of A. niger under laboratory conditions in humid atmosphere. Electrochemical impedance spectroscopy (EIS) ascertained microbially influenced corrosion acceleration (MICA) of Zn and inhibition (MICI) of Al. EIS data indicated a two-layer structure of corrosion products on Zn. The microorganisms reduced the thickness of the inner layer, whose passivating capacity was much higher when compared to that of the outer layer. An increase in aluminium oxide layer resistance but decrease in the layer thickness implied that MICI affected primarily the sites of localized corrosion of Al (pores, micro-cracks, etc.). X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) studies indicated that bioproducts (i.e. organic acids) did not form crystalline phases with corrosion products of zinc. The study suggested a hypothesis that microorganisms could be used as corrosion protectors instead of toxic chemicals, application of which tends to be increasingly restricted.     

Laboratory scale investigation into the corrosion of copper in a sulphur-containing environment

The effect of temperature and gas composition on the corrosion rate and corrosion by-product of copper foil was studied by exposing it to sulphur (S₂), S₂ + hydrochloric acid (HCl) and hydrogen sulphide. The temperature was varied from 80 to 140 °C. Copper foil reacted with S₂ to form CuS, Cu₉S₈ and Cu_1.8S. Corrosion rates ranged from 9.6 μm/h at 110 °C to 0.5 μm/h at 140 °C. The presence of HCl caused pitting and enhanced the corrosion rate above 112 °C. Cu₂S formed when copper was exposed to hydrogen sulphide gas. Sulphide scale that formed was friable and non-adherent.     

Influence of 1,2-diaminoethane on the mechanism of aluminium corrosion in sulphuric acid solutions

The influence of 1,2-diaminoethane (DAE) on aluminium corrosion in H₂SO₄ solutions (pH 3) was investigated. In pure H₂SO₄, rapid uniform corrosion is followed by inhibition due to the formation of stable Al-sulphate binuclear bidentate metal bound surface complexes via a ligand exchange mechanism with two neighbouring sites. Metastable pitting is also observed. DAE acts as a strong corrosion inhibitor for both uniform and localised corrosion, due to the formation of Al-DAE monodentate hydrogen-bond surface complexes either by direct adsorption of the protonated molecule on Al-OH sites or via a ligand exchange mechanism with the proton of an site.     

Pitting corrosion of Type 430 stainless steel under chloride solution droplet

To clarify the critical relative humidity (RH) to initiate pitting corrosion and the rusting mechanism in a marine atmospheric environment, pitting corrosion of Type 430 stainless steels under drops of MgCl₂ solutions were investigated. A pitting corrosion test was performed at different relative humidities under droplets with various diameters and thicknesses. The probability of pitting decreased as the diameter and thickness decreased. Pitting progressed only when the chloride concentration exceeded 4 M, which is the equilibrium concentration at 80% RH. Accordingly, pitting of Type 430 could be initiated when the RH was less than 80%. Additionally, a pitting corrosion mechanism of Type 430 stainless steel under droplets containing chloride ions is proposed.     

Degradation mechanism of galvanized steel in wet-dry cyclic environment containing chloride ions

The wet-dry cyclic test of a galvanized steel (GI) and pure zinc (ZN), which simulates marine atmospheric environment, has been conducted to clarify the degradation mechanism of galvanized steel. The samples were exposed to alternate conditions of 1 h-immersion in a 0.05 M NaCl solution and 7 h-drying at 25 °C and 60%RH, and the corrosion was monitored for 10 days (30 cycles) using a two-electrode type probe. Simultaneously, the corrosion potential was measured every three cycles only during the immersed conditions. The reciprocal of polarization resistance R_p⁻¹ was taken as an index of the corrosion rate. Several sample plates of GI and ZN were exposed, together with the monitoring probes. They were removed from the test chamber at the end of 1st, 3rd, 9th, 18th, and 30th cycles of exposure and were analyzed for the corrosion products with XRD and laser Raman spectroscopy. Further, their cross sections were analyzed with FESEM-EDS. The FESEM photographs and elemental analysis of cross sections confirmed that the R_p⁻¹ value commences to decrease when the corrosion front reaches Zn-Fe alloy layers (boundary layers of zinc coating and steel substrate) due to localized nature of attack. A schematic model of degradation mechanism and the role of galvanic protection have been discussed.