Quantitative analysis of 39 polybrominated diphenyl ethers by isotope dilution GC/low-resolution MS

A GC/low-resolution MS method for the quantitative isotope dilution analysis of 39 mono- to heptabrominated diphenyl ethers was developed. The effects of two different ionization sources, electron impact (EI) and electron capture negative ionization (ECNI), and the effects of their parameters on production of high-mass fragment ions [M - xH - yBr](-) specific to PBDEs were investigated. Electron energy, emission current, source temperature, ECNI system pressure, and choice of ECNI reagent gases were optimized. Previously unidentified enhancement of PBDE high-mass fragment ion [M - xH - yBr](-) abundance was achieved. Electron energy had the largest impact on PBDE high-mass fragment ion abundance for both the ECNI and EI sources. By monitoring high-mass fragment ions of PBDEs under optimized ECNI source conditions, quantitative isotope dilution analysis of 39 PBDEs was conducted using nine (13)C(12) labeled PBDEs on a low-resolution MS with low picogram to femtogram instrument detection limits.     

Chromatographic and ionization properties of polybrominated diphenyl ethers using GC/high-resolution MS with metastable atom bombardment and electron impact ionization

The chromatographic and ionization properties of 35 polybrominated diphenyl ether (PBDE) congeners were investigated using GC/HRMS with metastable atom bombardment (MAB) and electron impact (EI) ionization. A multiple linear regression model based on bromine substitution patterns and MOPAC calculated physical properties was developed to predict relative GC retention times of individual PBDE congeners. Although five different sources of metastable rare gas atoms (He, N2, Ar, Xe, and Kr) were investigated with MAB ionization, only MAB-N2 provided adequate ionization efficiency and predictability. Because of reduced background noise to the MS detector, MAB-N2 had a lower limit of detection for tetra- and penta-BDEs than EI, despite having a lower sensitivity. Using MAB-N2, the molecular ion was always the base peak, with little fragmentation taking place. Conversely, using EI ionization, the [M - nBr]+ peak (where n = 1-4, depending on the number of Br substituents) was the dominant ion for all PBDE congeners. Multiple linear regression models representing the molecular ion response of PBDE congeners analyzed by GC/ HRMS with MAB-N2 and EI ionization were also developed using the number and type of Br substituents and ionization potentials. A significantly higher level of predictability was obtained for the MAB-N2 response model than for EI.     

Measurement of selected polybrominated diphenyl ethers, polybrominated and polychlorinated biphenyls, and organochlorine pesticides in human serum and milk using comprehensive two-dimensional gas chromatography isotope dilution time-of-flight mass spectrometry

A new method using comprehensive two-dimensional gas chromatography and isotope dilution time-of-flight mass spectrometry (GCxGC-IDTOFMS) for the simultaneous measurement of selected polychlorinated biphenyls (PCBs), organochlorine pesticides (OCPs), and brominated flame retardants is presented. In contrast to the reference methods based on classical GC/MS, a single injection of the extract containing all compounds of interest results in accurate identification and quantification. Using GCxGC ensures the chromatographic separation of most compounds, and TOFMS allows mass spectral deconvolution of coeluting compounds as well as the use of (13)C-labeled internal standards for quantification. Isotope ratio measurements of the most intense ions for both native and labels ensure the required specificity. The use of this new method with an automated sample preparation procedure developed at the Centers for Disease Control and Prevention (CDC) for the analysis of human serum and milk compared favorably to conventional isotope-dilution one-dimensional gas chromatography-high-resolution mass spectrometry (GC-IDHRMS) for the different human serum and milk pools tested. The instrumental detection limits ranged between 0.5 pg/microL and 10 pg/microL and the method detection limits ranged between 1 and 15 pg/microL (N = 59 analytes). The reproducibility of the method was almost as good as with GC-IDHRMS, the relative standard deviations ranging between 1 and 11% for OCPs measured in human serum. OCP, PBDE, and PCB levels measured using the two methods were highly correlated, and the deviations between the two methods were below 20% for most analytes with concentrations above 1 ng/g milk lipids.     

Determination of polybrominated diphenyl ethers and polychlorinated biphenyls in human adipose tissue by large-volume injection-narrow-bore capillary gas chromatography/electron impact low-resolution mass spectrometry

A new analytical method has been developed for the quantification of polybrominated diphenyl ethers (PBDEs) in human adipose tissue samples. After Soxhlet extraction and a cleanup procedure using two successive solid-phase extraction cartridges containing acid silica and acid silica: neutral silica:deactivated basic alumina (from top to bottom), detection can been achieved by narrow-bore (0.10-mm i.d.) capillary gas chromatography/electron impact low-resolution mass spectrometry using a large-volume injection technique. Using narrow-bore capillaries, it is possible to analyze complex mixtures in a short time (up to 10 min), saving 50% or more of the analysis time of conventional columns while maintaining a similar resolution power. The method allows the determination of five major PBDE congeners (BDE 28, 47, 99, 100, and 153) at concentrations below 1 ng/g lipid weight. Detection limits in the selected ion mode varied between 0.05 and 0.30 ng/g lipid weight, depending on the degree of bromination. The sensitivity of this method can compete with low-resolution mass spectrometry with electron capture ionization, while a much better selectivity is obtained. Levels of PBDEs in 20 Belgian human adipose tissue samples ranged between 2.18 and 11.70 ng/g lipid weight and were similar to previously reported values from Europe.     

Development of a solid-phase microextraction gas chromatography/tandem mass spectrometry method for polybrominated diphenyl ethers and polybrominated biphenyls in water samples

Solid-phase microextraction has been applied for the first time to the determination of trace concentrations of some brominated flame-retardant compounds (BFRs) in water samples. For the development of the method, six polybrominated diphenyl ethers and two polybrominated biphenyls were considered as target analytes. The factors expected to influence the extraction process are fully discussed. Quantification has been performed by gas chromatography/tandem mass spectrometry using an ion trap mass analyzer. This is also the first time that tandem mass spectrometry is applied with these analytes. Unlike conventional methods for BFR analysis, which involve solvent extraction and several cleanup steps before gas chromatography, the proposed method uses headspace extraction and hard contamination of the chromatographic system is prevented. In addition, tandem mass spectrometry provides selectivity and sensitivity in the detection process. The method performs well achieving good linearity (R(2) > 0.997), precision, and detection limits (S/N = 3) ranging from 7.5 to 190 pg/L. The method has been applied to a variety of water samples.     

Determination of chromium in urine by stable isotope dilution gas chromatography/mass spectrometry using lithium bis(trifluoroethyl)dithiocarbamate as a chelating agent

An isotope dilution gas chromatography/mass spectrometry method using lithium bis(trifluoroethyl)dithiocarbamate as a chelating agent is described for the determination of chromium in urine. A wet digestion procedure with HNO3-H2O2 is used for oxidizing the organic matter associated with urine samples. The isotope ratios are measured by selected ion monitoring in a general-purpose mass spectrometer using a 10-m fused silica capillary column. Memory effect, in sequential analyses of samples with different isotope ratios, was evaluated by preparing a series of synthetic mixtures and was found to be negligible. The accuracy of the method was verified by quantitation of chromium in the NIST freeze-dried urine reference material, SRM-2670, with a recommended chromium concentration of 13 micrograms/L in the normal level and certified chromium concentration of 85 +/- 6 micrograms/L in the elevated level.     

Determination of iodine in oyster tissue by isotope dilution laser resonance ionization mass spectrometry

The technique of laser resonance ionization mass spectrometry has been combined with isotope dilution analysis to determine iodine in oyster tissue. The long-lived radioisotope, 129I, was used to spike the samples. Samples were equilibrated with the 129I, wet ashed under controlled conditions, and iodine separated by coprecipitation with silver chloride. The analyte was dried as silver ammonium iodide upon a tantalum filament from which iodine was thermally desorbed in the resonance ionization mass spectrometry instrument. A single-color, two-photon resonant plus one-photon ionization scheme was used to form positive iodine ions. Long-lived iodine signals were achieved from 100 ng of iodine. The precision of 127I/129I measurement has been evaluated by replicate determinations of the spike, the spike calibration samples, and the oyster tissue samples and was 1.0%. Measurement precision among samples was 1.9% for the spike calibration and 1.4% for the oyster tissue. The concentration of iodine determined in SRM 1566a, Oyster Tissue, was 4.44 micrograms/g with an estimate of the overall uncertainty for the analysis of +/- 0.12 microgram/g.     

Determination of methionine and selenomethionine in yeast by species-specific isotope dilution GC/MS

A method for the simultaneous determination of methionine (Met) and selenomethionine (SeMet) in yeast using species-specific isotope dilution (ID) gas chromatography/mass spectrometry (GC/MS) is described. Samples were digested by refluxing for 16 h with 4 M methanesulfonic acid. Analytes were derivatized with methyl chloroformate and extracted into chloroform for GC/MS analysis. In addition to use of commercially available 13C-enriched Met and SeMet spikes for species specific ID analysis, a 74Se-enriched SeMet spike was also available for comparison of results. In selective ion monitoring mode, the intensities of ions at m/z 221, 222, 269, 270, and 263 were used to calculate the 221/222, 269/270, and 269/263 ion ratios for quantification of Met and SeMet. Concentrations of 5959 +/- 33 and 3404 +/- 12 microg g(-1) (one standard deviation, n = 6) with relative standard deviations of 0.55 and 0.36% for Met and SeMet, respectively, were obtained using 13C-enriched spikes. A concentration of 3417 +/- 8 microg g(-1) (one standard deviation, n = 6) was obtained using the 74Se-enriched SeMet spike. The concentration of SeMet measured in the yeast is equivalent to 66.43 +/- 0.24% of total Se and 30.31 +/- 0.11% of total Met is in the form of SeMet. Method detection limits (three times the standard deviation) of 3.4 and 1.0 microg g(-1) were estimated for Met and SeMet, respectively, based on a 0.25-g subsample of yeast with 1 mL of extract used for derivatization. A similar concentration of 5930 +/- 29 microg g(-1) (one standard deviation, n = 4) for Met and a lower concentration of 2787 +/- 49 microg g(-1) (one standard deviation, n = 4) for SeMet were obtained for this yeast sample using species-specific ID analysis based on GC/MS with 13C-enriched Met and SeMet spikes when a 2-h open microwave digestion approach using 8 M methanesulfonic acid was used.     

气相色谱-质谱测定化妆品中的硝基麝香类化合物

建立了化妆品中5种硝基麝香含量的气相色谱-质谱联用检测方法。采用丙酮/正己烷混合液超声提取化妆品中的硝基麝香,提取液经过浓缩,由气相色谱-质谱联用仪检测,以氘代二甲苯麝香内标法定量。该方法对化妆品中5种硝基麝香的加标回收率在85.21%~110.2%之间,相对标准偏差(RSD)不大于7.15%,在50μg/L~5000μg/L范围内呈现良好的线性关系,灵敏度高,最低检测限分别达到20~50μg/kg;选择性好,能有效消除复杂基体干扰。可用于常见化妆品中硝基麝香类化合物含量的检测。     

Application of isotopically labeled methylmercury for isotope dilution analysis of biological samples using gas chromatography/ICPMS

An isotope dilution (ID) procedure for the determination of methylmercury (MMHg) in biological samples using an inductively coupled plasma mass spectrometer as detector after the capillary gas chromatographic separation (CGC/ICPMS) has been developed. For the first time, open-focused-microwave pretreatment has been used in conjunction with ID. Optimum conditions for the measurement of isotope ratios on the fast transient chromatographic peaks have been established. Mass bias was found to be about 1.5%/mass unit and was corrected by using the simultaneously measured thallium signals at 203Tl and 205Tl. After mass-bias correction, deviation of the theoretical mercury ratio values was found to be as low as 0.2%. Isotope ratio precisions based on the peak areas measurements were 0.3% RSD for 20 pg injected (as Hg absolute). The absolute detection limits were in the range of 20-30 fg for 202Hg and 201Hg. Methylmercury enriched in 201Hg has been synthesized by direct reaction with methylcobalamine. The concentration of the MMHg spike has been measured by reverse isotope dilution with a natural MMHg standard. The capabilities of CGC/ICPMS to measure isotope ratios were used to optimize sample derivatization by aqueous ethylation with NaBEt4 with respect to MMHg degradation pathways and quantitative recovery. The accuracy of the method developed has been validated with biological certified reference materials (CRM-463, DORM-1).     

气相色谱法测定二十二烷酸含量

建立了一种测定二十二烷酸含量的方法.用气相色谱法测定二十二烷酸的含量,采用Agilent DB-5毛细管柱(30m×0.32mm×0.25μm);柱温箱的起始温度为200℃,以10℃·min~(-1)的速率升温至300℃,气化室温度为320℃,FID检测器温度为320℃;进样量1μL;分流比1∶20.实验结果显示,二十二烷酸在2~10mg·mL~(-1)的范围内线性关系良好(R2=0.999),平均加样回收率为99.8%(RSD=0.53%,n=9).     

Determination of alkyltrimethylammonium chlorides in river water by gas chromatography/ion trap mass spectrometry with electron impact and chemical ionization

This work describes a modified method to analyze alkyltrimethylammonium chlorides (ATMACs) in river water samples. The proposed method involves adding solid potassium iodide to water sample (pH adjusted to 10.0) as a counterion to enhance the extraction of ATMAC residues by dichloromethane liquid-liquid extraction. The iodide-ATMA+ ion pairs were demethylated to their corresponding nonionic alkyldimethylamines (ADMAs) by thermal decomposition in a GC injection port. The corresponding ADMAs were then identified and quantitated by gas chromatography/ion trap mass spectrometry (GC/MS) in electron impact and low-pressure positive ion chemical ionization (PICI) modes. A relatively high abundance of ADMAs was detected at a demethylation temperature above 300 degrees C in the injection port. Experimental results indicate that the proposed method is precise and sensitive in ATMACs analysis and allows quantitation at < or = 0.01 microg/L in 500 mL of the water samples. The enhanced selectivity of quasi-molecular ion chromatograms of C12-C18-ADMA, obtained using methanol PICI-MS, enables ATMAC residues to be identified at trace levels in environmental samples. Recovery of the ATMACs in various spiked water samples ranged from 70 to 94% while RSD ranged from 3 to 12%. The concentrations of total measured ATMAC residues in river water samples ranged from nondetectable to 1.24 microg/L.     

Determination of thermodynamic interactions of poly(l-lactide) and biphasic calcium phosphate/poly(l-lactide) composite by inverse gas chromatography at infinite dilution

Inverse gas chromatography at infinite dilution was applied to determine the thermodynamic interactions of poly(l-lactide) (PLLA) and the composite of biphasic calcium phosphate and PLLA (BCP/PLLA). The specific retention volumes, $ V_{\text{g}}^{0} $ , of 11 organic compounds of different chemical nature and polarity (non-polar, donor or acceptor) were determined in the temperature range of 308–378 K for PLLA and 308–398 K for BCP/PLLA. The weight fraction activity coefficients of test sorbates, $ \Omega_{1}^{\infty } $ , and the Flory–Huggins interaction parameters, $ \chi_{12}^{\infty } $ , were estimated and discussed in terms of interactions of the sorbates with PLLA and BCP/PLLA. Also, the partial molar free energy, $ \Delta G_{1}^{\infty } $ , the partial molar heat of mixing, $ \Delta H_{1}^{\infty } $ , the sorption molar free energy, $ \Delta G_{1}^{\text{S}} $ , the sorption enthalpy, $ \Delta H_{1}^{\text{S}} $ , and the sorption entropy, $ \Delta S_{1}^{\text{S}} $ , were analyzed. A different chromatographic behavior of the two investigated samples, PLLA and BCP/PLLA, was observed. The values of $ \Omega_{1}^{\infty } $ indicated n-alkanes, diethyl ether, tetrahydrofurane (THF), cyclohexane, benzene, dioxane (except for 338 K), and ethyl acetate (EtAc) (except for 338 K) as non-solvents, and chloroform (CHCl₃) as good solvent (except for 378 K) for PLLA. For BCP/PLLA, CHCl₃, EtAc (for 378 K), dioxane (except for 378 K), and THF were indicated as good solvents.     

Measurement of urinary monohydroxy polycyclic aromatic hydrocarbons using automated liquid-liquid extraction and gas chromatography/isotope dilution high-resolution mass spectrometry

A method for the measurement of 24 hydroxylated polycyclic aromatic hydrocarbon metabolites (OH-PAHs) in urine has been developed. The method is based on enzymatic deconjugation, automated liquid-liquid extraction, and gas chromatography/isotope dilution high-resolution mass spectrometry after derivatization of the OH-PAHs to the trimethylsilylated derivatives. The metabolites included in the current method are formed from eight different parent compounds. The limits of detection were below 7 pg/mL when using a sample size of 2 mL of urine, except for 1- and 2-naphthols (18 and 12 pg/mL, respectively). The enzymatic deconjugation efficiency, verified by deconjugation of urine samples spiked with alpha-naphthyl beta-d-glucuronide sodium salt (1-NAP-GLU) and pyrene-1-sulfate potassium salt (1-PYR-SULF), was determined to be 97% for 1-NAP-GLU conjugate and 84% for 1-PYR-SULF. The overall coefficients of variance for six batches of quality control samples (n = 42), was 2.9-11%. Mean method recoveries of the 13C-labeled internal standards were 66-72%, except for 13C6-1-naphthol (46%). The throughput of this method has been determined to be 40 samples per day per analyst. This method is currently applied to epidemiological studies, such as the National Exposure and Nutrition Examination Survey (NHANES), to measure human exposure to PAHs.     

Simultaneous determination of five tobacco-specific nitrosamines in mainstream cigarette smoke by isotope dilution liquid chromatography/electrospray ionization tandem mass spectrometry

Tobacco-specific nitrosamines (TSNAs) have been previously implicated as a source of carcinogenicity in tobacco and cigarette smoke. Accurate quantification of these chemicals is needed to help assess public health risk. We have developed and validated a specific and sensitive method to simultaneously measure five TSNAs in the particulate phase of mainstream tobacco smoke. Cigarette smoke particulate, produced using standardized machine smoking protocols, was collected on a Cambridge filter pad. The particulate matter was extracted using methylene chloride, back extracted into aqueous solution, further purified by solid-phase extraction, and analyzed by liquid chromatography/electrospray ionization tandem mass spectrometry using isotopically labeled analogues as internal standards. Limits of detection for this method ranged from 0.05 to 1.23 ng/mL using an injection volume of 20 microL. A linear calibration range spanning 2.5-2500 ng/mL was adequate to measure TSNA levels in cigarette smoke. The method achieved excellent reproducibility and accuracy. The identity of each TSNA was established by chromatographic retention time, analyte-specific fragmentation patterns, and relative peak area ratios of two product/precursor ion pairs. This new method provides higher sensitivity, specificity, and throughput than earlier methods for TSNA determination.