Oxygenated blend design and its effects on reducing diesel particulate emissions

In order to meet Euro IV emission standards, diesel vehicles are compelled to install exhaust aftertreatment devices, which largely increases the overall cost. This paper explores the possibility to significantly reduce the particulate matter (PM) emissions by new fuel design. Several oxygenated blends were obtained by mixing the biodiesel, ethanol, dimethyl carbonate (DMC), and diesel fuels. The tests were conducted on two heavy-duty diesel engines, both with a high-pressure injection system and a turbocharger. The total PM and its dry soot (DS) and soluble organic fraction (SOF) constituents were analyzed corresponding to their specific fuel physiochemical properties. A blended fuel that contains biodiesel, DMC, and high cetane number diesel fuels was chosen eventually to enable the diesel engines to meet the Euro IV emission regulation. Based on the test results, the basic design principles were derived for the oxygenated blends that not only need the high oxygen content, but also the high cetane number and the low sulfur and low aromatic contents.     

Combustion characteristics of waste-oil produced biodiesel/diesel fuel blends

In this study, wasted cooking oil from restaurants was used to produce neat (pure) biodiesel through transesterification, and this converted biodiesel was then used to prepare biodiesel/diesel blends. The goal of this study was to compare the trace formation from the exhaust tail gas of a diesel engine when operated using the different fuel type: neat biodiesel, biodiesel/diesel blends, and normal diesel fuels. B20 produced the lowest CO concentration for all engine speeds. B50 produced higher CO₂ than other fuels for all engine speeds, except at 2000 rpm where B20 gave the highest. The biodiesel and biodiesel/diesel blend fuels produced higher NO_x for various engine speeds as expected. SO₂ formation not only showed an increasing trend with increased engine speed but also showed an increasing trend as the percentage of diesel increased in the fuels. Among the collected data, the PM concentrations from B100 engines were higher than from other fuelled engines for the tested engine speed and most biodiesel-contained fuels produced higher PM than the pure diesel fuel did. Overall, we may conclude that B20 and B50 are the optimum fuel blends. The species of trace formation in the biodiesel-contained fuelled engine exhaust were mainly C_nH_2n+2, DEP, and DPS. For the B100, B80, B50, and D fuelled engines, C₁₅H₃₂ was the dominant species for all engine speeds, while squalene (C₃₀H₅₀) was the dominant for B20. DEP was only observed in the B100, B80, and B50 fuelled engines in this study. The D fuelled engine showed a higher DPS production for engine speeds higher than 1200 rpm.     

Emission characteristics of diesel, gas to liquid, and biodiesel-blended fuels in a diesel engine for passenger cars

The need for diversification of energy sources and reducing various emissions including CO₂ emission in diesel engine can be met with alternative diesel fuels such as gas to liquid (GTL) and GTL–biodiesel blends. But there should be a clear understanding of the combustion and engine-out emission characteristics for alternative fuels. In this respect, an experimental study was conducted on a 2.0 L 4 cylinders turbocharged diesel engine fuelled with those alternative diesel fuels to investigate the engine-out emission characteristics under various steady-state engine operating conditions. The results revealed that noticeable decreases in THC (22–56%) and CO (16–52%) emissions for GTL–biodiesel blends were observed, whereas NOx emissions for GTL–biodiesel blends increased by a maximum of 12% compared to diesel. With regard to particle size distributions (PSDs) for GTL–biodiesel blends, the particulate matter (PM) number concentration in accumulation mode decreased, as a result of the excess oxygen content in biodiesel. Contrary to the tendency in the accumulation mode, there was a slight increase in the PM number concentration in the nucleation mode under the operating conditions wherein the exhaust gas recirculation (EGR) strategy was applied. The total PM number concentration for G + BD40 decreased by a maximum of 46% compared to that for diesel. From these results of enhanced emission characteristics compared to diesel and GTL fuel, the potential for the use of GTL–biodiesel blends could be confirmed.     

Biodiesel from safflower oil and its application in a diesel engine

Safflower seed oil was chemically treated by the transesterification reaction in methyl alcohol environment with sodium hydroxide (NaOH) to produce biodiesel. The produced biodiesel was blended with diesel fuel by 5% (B5), 20% (B20) and 50% (B50) volumetrically. Some of important physical and chemical fuel properties of blend fuels, pure biodiesel and diesel fuel were determined. Performance and emission tests were carried out on a single cylinder diesel engine to compare biodiesel blends with petroleum diesel fuel. Average performance reductions were found as 2.2%, 6.3% and 11.2% for B5, B20 and B50 fuels, respectively, in comparison to diesel fuel. These reductions are low and can be compensated by a slight increase in brake specific fuel consumption (Bsfc). For blends, Bsfcs were increased by 2.8%, 3.9% and 7.8% as average for B5, B20 and B50, respectively. Considerable reductions were recorded in PM and smoke emissions with the use of biodiesel. CO emissions also decreased for biodiesel blends while NO_x and HC emissions increased. But the increases in HC emissions can be neglected as they have very low amounts for all test fuels. It can be concluded that the use of safflower oil biodiesel has beneficial effects both in terms of emission reductions and alternative petroleum diesel fuel.     

Potential for reducing emissions in a diesel engine by fuelling with conventional biodiesel and Fischer-Tropsch diesel

A gas-to-liquid (GTL) fuel derived from Low Temperature Fischer-Tropsch process has been tested in an automotive diesel engine fulfilling Euro 4 emissions regulations. Both regulated and non-regulated emissions have been compared with those of a commercial diesel fuel, a commercial biodiesel fuel and a GTL-biodiesel fuel (30% and 70% v/v, respectively) in order to check blending properties, synergistic effects and compatibility between first and second generation production technologies for biofuel consumption in current diesel engines. After presenting a detailed literature review, and confirming that similar efficiencies are attained with the four tested fuels under identical road-like operating conditions (this meaning fuel consumption is inversely proportional to their heating values), significant reductions in smoke opacity, particulate matter emissions and particle number concentration were observed with both GTL and biodiesel fuels, with small changes in NO_x emissions. Compared with the reductions in PM emissions derived from the use of biodiesel fuels, those derived from using GTL fuels were quite similar, despite its lower soot emissions reductions. This can be explained by the lower volatile organic fraction of the PM in the case of GTL. By adequately blending both fuels, a considerable potential to optimise the engine emissions trade-off is foreseen.     

Reduction of diesel smoke opacity from vegetable oil methyl esters during transient operation

This work is focused on the measurement and analysis of the smoke opacity resulting from a Diesel engine fuelled with conventional fuel and biofuels under transient conditions. Methyl esters obtained from used cooking and unused vegetable oils were tested as diesel fuels, pure and blended with 30% and 70% of a commercial diesel fuel which was also used pure. A commercial engine was mounted in a test bench prepared for operating in different transient conditions. A smoke meter AVL 439 allowed for the study of the effect of these fuels on the smoke opacity under varied operating conditions. The thermo chemical properties of the test fuels and the engine parameters, such as fuel/air ratio or exhaust gas recirculation (EGR) ratio, were used for the analysis and interpretation of the results. The engine transient processes studied were (a) engine start, (b) load increase at constant engine speed and (c) engine speed decrease at constant torque. These results suggested that the use of the diesel blends containing vegetable esters is an interesting alternative for a significant reduction in smoke opacity not only in steady conditions but also in transient engine operation, the latter being the most usual condition in passenger vehicles.     

Effect of altitude and palm oil biodiesel fuelling on the performance and combustion characteristics of a HSDI diesel engine

Altitude above sea level and fuel’s chemical and physical nature affect engine performance and combustion characteristics. In this work, a combustion diagnosis model including exergy analysis was applied to a turbocharged (TC) automotive diesel engine fuelled with neat palm oil biodiesel (B100) and No. 2 diesel fuel (B0). Tests were performed under steady state operating conditions, at two altitudes above sea level: 500 and 2400 m. Biodiesel fuelling and altitude had an additive effect on the advance in injection and combustion timings. The duration of the premixed combustion stage increased with altitude and decreased with biodiesel. When B100 was used, the transition between this stage and the diffusion stage was practically suppressed. As altitude increased, biodiesel fuelling led to shorter combustion duration, and higher in-cylinder pressures and fuel-air equivalence ratios. Brake thermal efficiency decreased with altitude for both fuels, but in a greater extent for B0. For all fuels and altitudes, exergy destruction rose sharply when combustion started, indicating that this process was the main source of irreversibilities. At both altitudes, the cumulative exergy destruction was higher for B100 due to its earlier and faster combustion process. Some of the results obtained in this work indicate that palm oil biodiesel fuelling can lead to a better engine performance at high altitudes.     

Aviation fuel JP-5 and biodiesel on a diesel engine

Naval aviation turbine fuel, JP-5, has been accepted as alternative to JP-8 in the frame of the Single Fuel Policy. This has resulted in some ongoing research on JP-5 fuel for its application as a naval single fuel. The necessity to cope with the environmental problems identified in the process of implementing the Single Fuel Policy as well as the strict requirements of modern diesel engines has lead to the need of improved single fuel quality. The development of biomass derived substitutes for diesel, such as biodiesel, is a possible attractive solution. The present paper is an effort to evaluate JP-5 along with diesel and biodiesel for use in a diesel engine. These fuels were used alone and in various mixture fractions in a single cylinder stationary diesel engine in order to evaluate their performance under defined operating conditions of the engine. JP-5 reduced both the NOx and particulate matter emissions as compared to the reference fuel case. Biodiesel significantly lowered particulate emissions, but slightly increased NOx emissions and fuel consumption. Fuel sulfur content has an undesired effect on smoke opacity. Biodiesel increased the fuel consumption when added to petroleum fuels and the increase was larger at high engine loads. Diesel and JP-5 showed similar fuel consumption, with diesel consumption increasing at high engine loads. Ternary blends showed similar behavior. The blends with lower biodiesel content showed lower volumetric fuel consumption.     

Biodiesel blend effects on common-rail diesel combustion and emissions

Biodiesel (fatty acid methylesters) blends with fossil diesel at a mixing ratio between 0.5 and 5 vol.% are widely offered as automotive fuels in Europe. The target for the future is to bring this ratio to at least 10%, in order to increase the share of renewable energy in transport. There is however limited evidence on the effects of such blends on the combustion and emissions of diesel engines not originally designed to operate on biodiesel blends. In this study, a number of experiments with 10 vol.% (B10) biodiesel fuel of palmoil origin were performed on a light-duty common-rail Euro 3 engine. The measurements included in-cylinder pressure, pollutants emissions, and fuel consumption. Combustion effects were limited but changes in the start of ignition and heat-release rate could be identified. Emission effects included both higher and lower smoke and NOx, depending on the operation point. The results on the engine bench were compared against a Euro 3 common-rail light-duty vehicle driven on the chassis dynamometer, in order to include the effects of emission control systems (EGR and oxidation catalyst). In addition to the palm biodiesel, an RME-diesel blend was also tested to examine the effects of a fuel with different characteristics. Both biodiesel blends reduced PM emissions and only marginal effects on NOx over the certification test could be identified. The results of this study show that up to 10% biodiesels could be used on current diesel vehicles, without significantly affecting vehicle emission performance.     

The kinematic viscosity of biodiesel and its blends with diesel fuel

As the use of biodiesel becomes more wide-spread, engine manufacturers have expressed concern about biodiesel’s higher viscosity. In particular, they are concerned that biodiesel may exhibit different viscosity-temperature characteristics that could result in higher fuel injection pressures at low engine operating temperatures. This study presents data for the kinematic viscosity of biodiesel and its blends with No. 1 and No. 2 diesel fuels at 75, 50, and 20% biodiesel, from close to their melting point to 100°C. The results indicate that while their viscosity is higher, biodiesel and its blends demonstrate temperature-dependent behavior similar to that of No. 1 and No. 2 diesel fuels. Equations of the same general form are shown to correlate viscosity data for both biodiesel and diesel fuel, and for their blends. A blending equation is presented that allows the kinematic viscosity to be calculated as a function of the biodiesel fraction.     

A comparative study on the performance, emission and combustion studies of a DI diesel engine using distilled tyre pyrolysis oil–diesel blends

Alternate fuels like ethanol, biodiesel, LPG, CNG, etc., have been already commercialised in the transport sector. In this context, pyrolysis of solid waste is currently receiving renewed interest. The disposal of waste tyres can be simplified to a certain extent by pyrolysis. In the present work, the crude tyre pyrolyisis oil (TPO) was desulphurised and then distilled through vacuum distillation. Also, two distilled tyre pyrolysis oil (DTPO)–diesel fuel (DF) blends at lower and higher concentrations were used as fuels in a four stroke single cylinder air cooled diesel engine without any engine modification. The results were compared with diesel fuel (DF) operation. Results indicate that the engine can run with 90% DTPO and 10% diesel fuel.     

Optimization of a heavy-duty compression-ignition engine fueled with diesel and gasoline-like fuels

Optimal injection strategies for a heavy-duty compression-ignition engine fueled with diesel and gasoline-like fuels (#91 gasoline and E10) and operated under mid- and high-load conditions are investigated. A state-of-the-art engine CFD tool with detailed fuel chemistry was used to evaluate the engine performance and pollutant emissions. The CFD tools feature a recently developed efficient chemistry solver that allowed the optimization tasks to be completed in practical computer times. A Non-dominated Sorting Genetic Algorithm II (NSGA II) was coupled with the CFD tool to seek optimal combinations of injection system variables to achieve clean and efficient combustion. The optimization study identified several key parameters that influence engine performance. It was found that the fuel volatility and reactivity both play important roles at the mid-load condition, while the high-load condition is less sensitive to the fuel reactivity. However, high volatility fuels, such as gasoline and E10, were found to be beneficial to fuel economy at high-load. The study indicates that with an optimized injection system gasoline-like fuels are promising for heavy-duty CI engines due to their lower NOx and soot emissions and higher fuel economy compared to conventional diesel fuels. However, the high in-cylinder gas pressure rise rate associated with Partially Premixed Combustion of gasoline-like fuels can become problematic at high-load and the low-load operating limit is also a challenge. Potential solutions are discussed based on the present optimization results.     

Experimental study of the performance and emission characteristics of diesel engine using direct and indirect injection systems and different fuels

An experimental study of the performance and emission characteristics of diesel engine using direct and indirect injection combustion systems are carried out on a same model of two diesel engines fuelled with diesel and the blend of diesel and Chinese pistache biodiesel. The results show that the NO_x emissions from the indirect injection combustion system (ICS) fuelled with diesel are reduced by around two thirds, compared to that from direct injection combustion system (DCS). Smoke emissions from the engine using ICS are all significantly lower than that of DCS, reduced by 70% for diesel; by 50-60% for the blend. The brake thermal efficiencies (BTEs) reduced by 8-10%, compared to that of DCS; the fuel consumptions increased by around 7-9%. It is also found that carbon monoxide (CO) emissions are reduced when the engine run at engine high power outputs, so are the hydrocarbon (HC) emissions from ICS at the peak power outputs. It is found that, when fuelled with the blend, the effects of ICS to the performance and emissions of diesel engine are very similar to that of running with diesel. For ICS engine fuelled with diesel and the blend fuel, the BSFCs for the blend are around 5% higher; the BTEs are around 2-4% lower; the reductions of NO_x from the blend fuel are 5.1-8.4% on average for the ICS; the reductions of smoke from the blend fuel are 26.8-31.7% on average for the ICS. CO emissions are around a half lower; and HC emissions are around one fifth lower, compared to that of fuelling with diesel. Comparing to that of DCS fuelled with diesel, using ICS fuelled with the blended fuel has much lower emissions. NO_x emissions decreased by 65.6% and 66.1%; smoke emissions decreased by 75.7% and 80.2%; CO emissions decreased by 55.8% and 46.0%; HC emissions decreased by 24.9% and 18.9%; with the BSFCs around 14.6-14.9% higher and the BTEs around 9.7-10.0% lower.     

Evaluation of the oxidation stability of diesel/biodiesel blends

Biodiesel is an alternative fuel derived from vegetable oils, animal fats and used frying oils. Due to its chemical structure, it is more susceptible to oxidation or autoxidation during long-term storage compared to petroleum diesel fuel. One of the major technical issues regarding the biodiesel blends with diesel fuel is the oxidation stability of the final blend, which is, nowadays, of particularly high concern due to the introduction of ultra low sulphur diesel, in most parts of the EU. This study examined the factors influencing the stability of several biodiesel blends with low and ultra low sulphur automotive diesel fuels. The aim of this paper was to evaluate the impact of biodiesel source material and biodiesel concentration in diesel fuel, on the stability of the final blend. Moreover, the effects of certain characteristics of the base diesels, such as sulphur content and the presence of cracked stocks, on the oxidation stability are discussed.     

Effect of the alcohol type used in the production of waste cooking oil biodiesel on diesel performance and emissions

Experimental results were obtained by testing two different alcohol-derived biodiesel fuels: methyl ester and ethyl ester, both obtained from waste cooking oil. These biodiesel fuels were tested pure and blended (30% and 70% biodiesel content, volume basis) with a diesel reference fuel, which was tested too, in a 2.2 l, common-rail injection diesel engine. The operation modes were selected to simulate the European Driving Cycle. Pure biodiesel fuels, compared to the reference fuel, resulted in a slight increase in fuel consumption, in very slight differences in NOx emissions, and in sharp reductions in total hydrocarbon emissions, smoke opacity and particle emissions (both in mass and number), despite the increasing volatile organic fraction of the particulate matter. The type of alcohol used in the production process was found to have a significant effect on the total hydrocarbon emissions and on the particulate matter composition. As the alcohol used was more volatile, both the hydrocarbon emissions and volatile organic fraction of the particulate matter were observed to increase.     

Mitigation of NOx emissions from a jatropha biodiesel fuelled DI diesel engine using antioxidant additives

Biodiesel offers cleaner combustion over conventional diesel fuel including reduced particulate matter, carbon monoxide and unburned hydrocarbon emissions. However, several studies point to slight increase in NO_x emissions (about 10%) for biodiesel fuel compared with conventional diesel fuel. Use of antioxidant additives is one of the most cost-effective ways to mitigate the formation of prompt NO_x. In this study, the effect of antioxidant additives on NO_x emissions in a jatropha methyl ester fuelled direct injection diesel engine have been investigated experimentally and compared. A survey of literature regarding the causes of biodiesel NO_x effect and control strategies is presented. The antioxidant additives L-ascorbic acid, α tocopherol acetate, butylated hydroxytoluene, p-phenylenediamine and ethylenediamine were tested on computerised Kirloskar-make 4 stroke water cooled single cylinder diesel engine of 4.4 kW rated power. Results showed that antioxidants considered in the present study are effective in controlling the NO_x emissions of biodiesel fuelled diesel engines. A 0.025%-m concentration of p-phenylenediamine additive was optimal as NO_x levels were substantially reduced in the whole load range in comparison with neat biodiesel. However, hydrocarbon and CO emissions were found to have increased by the addition of antioxidants.     

Engine-out characterisation using speed-load mapping and reduced test cycle for a light-duty diesel engine fuelled with biodiesel blends

In this two-phase experimental programme, key effects of different biodiesel fuels and their blends on engine-out responses of a light-duty diesel engine were investigated. Here, coconut methyl ester (CME), palm methyl ester (PME) and soybean methyl ester (SME) were tested to represent the wide spectrum of degree of saturations in the fatty acid composition. Fossil diesel which served as the blending component was used as the baseline fuel for benchmarking purposes. Phase I examined how engine speed and load affect patterns of variation in tailpipe emissions and engine performance parameters for the test fuels. Here, the trends in engine-out responses across the operational speed-load map for all the tested biodiesel fuels were similar and consistent throughout. However, there were marked differences in the levels of equivalence ratio and specific fuel consumption, as well as exhaust concentrations of CO, UHC and smoke opacity. This is mainly due to differences in fuel properties, especially fuel-bound oxygen content, density and impurity level. Phase II appraised the performance of 31 different fuel blend combinations of fossil diesel blended with CME, PME or SME at 10 vol.% interval under a steady-state test cycle. The use of biodiesel fuels with low to moderate degree of unsaturation was found to conclusively reduce regulated emission species of UHC, NO and smoke opacity levels by up to 41.7%, 5.4% and 61.3%, respectively. This is in contrast to the performance of the highly unsaturated SME, where CO, UHC, NO and smoke opacity levels are higher in relation to that of fossil diesel. Simultaneous NO-smoke reduction can be achieved through the introduction of at least 1 vol.% of PME or 50 vol.% of CME into diesel fuel, although minor trade-off in the higher specific fuel consumption is observed.     

Cold start and fuel consumption of a vehicle fuelled with blends of diesel oil–soybean biodiesel–ethanol

Fuel consumption and cold start characteristics of a production vehicle fuelled with blends of N. 2 diesel oil (500 ppm sulfur content), soybean biodiesel (3%, 5%, 10%, and 20%) and hydrous ethanol (2% and 5%) were compared. A wagon-type vehicle equipped with a four-cylinder, 1.3-l, 63 kW diesel engine was tested in a cold chamber at the temperature of −5 °C for the cold start tests. Fuel consumption tests were performed following the 1975 US Federal Test Procedure (FTP-75). The results showed that the cold start time was satisfactory for all fuel blends tested, but it was longer for the blend containing 20% of soybean biodiesel (B20) in comparison with the blends with lower biodiesel concentration. The cold start time also increased with increasing with increasing ethanol content in the fuel blend. Specific fuel consumption was not affected by increasing biodiesel concentration in the blend or by the use of 2% of ethanol as an additive. However, the use of 5% of ethanol concentration in the B20 blend resulted in increased specific fuel consumption.     

Biodiesel CO2 emissions: A comparison with the main fuels in the Brazilian market

The use of biodiesel is increasing as an attractive fuel due to the depleting fossil fuel resources and environmental degradation. This paper presents results of an investigation on the potentials of biodiesel as an alternative fuel and main substitute of diesel oil, comparing the CO₂ emissions of the main fuels in the Brazilian market with those of biodiesel, in pure form or blended in different proportions with diesel oil (2%, 5%, and 20%, called B2, B5, and B20, respectively). The results of the study are shown in ton CO₂ per m³ and ton CO₂ per year of fuel. The fuels were analyzed considering their chemical composition, stoichiometric combustion parameters and mean consumption for a single vehicle. The fuels studied were: gasoline, diesel oil, anhydrous ethyl alcohol (anhydrous ethanol), and biodiesel from used frying oil and from soybean oil. For the case of biodiesel, its complete life cycle and the closed carbon cycle (photosynthesis) were considered. With data provided by the Brazilian Association of Automotive Vehicle Manufacturers (ANFAVEA) for the number of vehicles produced in Brazil, the emissions of CO₂ for the national fleet in 2007 were obtained per type of fuel. With data provided by the Brazilian Department of Transit (DENATRAN) concerning the number of diesel vehicles in the last five years in Brazil, the total CO₂ emissions and the percentage that they would decrease in the case of use of pure biodiesel, B100, or several mixtures, B2, B5 and B20, were calculated. Estimates of CO₂ emissions for a future scenario considering the mixtures B5 and B20 are also included in this article.     

Various strategies for reducing Nox emissions of biodiesel fuel used in conventional diesel engines: A review

Energy demand, decreasing fossil fuel reserves, and health-related issues about pollutants have led researchers to search for renewable alternative fuels to either partially or fully replace fossil fuels. Among many alternative fuels, biodiesel became one of the most popular choices due to similar properties to that of conventional diesel. Biodiesel produces slightly lower brake thermal efficiency compared to that of conventional biodiesel, but has an advantage of reduced emissions of CO₂, CO, HC, and smoke. However, biodiesel shows higher NOx emission which, when used in increased biodiesel market, may become a serious problem. Various strategies were attempted by different researcher to reduce NOx emissions. In this paper, various strategies, adapted for reducing NOx emissions of biodiesel fuel used in diesel engines for automobile applications, are reviewed and discussed. The strategies are grouped into three major groups, namely combustion treatments, exhaust after-treatments, and fuel treatments. Among various strategies discussed, fuel treatments, such as low temperature combustion, mixing fuel additives and reformulating fuel composition, reduce NOx emission without compromising other emission and performance characteristics and they seem to be promising for future biodiesel fuel.