An experimental study on the heat transfer performance and pressure drop of TiO2-water nanofluids flowing under a turbulent flow regime

Nanofluid is a new class of heat transfer fluids engineered by dispersing metallic or non-metallic nanoparticles with a typical size of less than 100 nm in the conventional heat transfer fluids. Their use remarkably augments the heat transfer potential of the base liquids. This article presents the heat transfer coefficient and friction factor of the TiO₂-water nanofluids flowing in a horizontal double tube counter-flow heat exchanger under turbulent flow conditions, experimentally. TiO₂ nanoparticles with diameters of 21 nm dispersed in water with volume concentrations of 0.2–2 vol.% are used as the test fluid. The results show that the heat transfer coefficient of nanofluid is higher than that of the base liquid and increased with increasing the Reynolds number and particle concentrations. The heat transfer coefficient of nanofluids was approximately 26% greater than that of pure vol.%, and the results also show that the heat transfer coefficient of the nanofluids at a volume concentration of 2.0 vol.% was approximately 14% lower than that of base fluids for given conditions. For the pressure drop, the results show that the pressure drop of nanofluids was slightly higher than the base fluid and increases with increasing the volume concentrations. Finally, the new correlations were proposed for predicting the Nusselt number and friction factor of the nanofluids, especially.     

Rheology and thermal conductivity of non-porous silica (SiO2) in viscous glycerol and ethylene glycol based nanofluids

Nanofluids are advanced fluids with novel properties useful for diverse applications in heat transfer. This article reports the experimental determination of thermal conductivity and viscosity for silica (SiO₂) nanofluids in ethylene glycol (EG) and glycerol (G) as base fluids. A two-step method was applied to disperse the nanoparticles in the base fluids for the particle volume concentration of 0.5–2.0%. The dispersion stability of the nanofluids was evaluated by zeta potential analysis. All the measurements were performed in the temperature interval from 30 °C to 80 °C. It was found that the thermal conductivity increases with temperature. The SiO₂-EG showed higher conductivity enhancement than SiO₂-G nanofluids. Rheological analyses confirm Newtonian behavior for silica nanofluids within shear rate range of 20–100 s^− 1. Viscosity decreases with an increase in operating temperature. The SiO₂-EG demonstrated very weak temperature dependence compared to the SiO₂-G nanofluids. Based on these measured properties, the criterion for heat transfer performance was determined. Furthermore, equations have been proposed with accuracy within ± 10% deviations to predict the thermal conductivity and dynamic viscosity of EG and G-based SiO₂ nanofluids.     

Experimental investigation of heat transfer and friction factor with water–propylene glycol based CuO nanofluid in a tube with twisted tape inserts

Convective heat transfer and friction factor characteristics of water/propylene glycol (70:30% by volume) based CuO nanofluids flowing in a plain tube are investigated experimentally under constant heat flux boundary condition. Glycols are normally used as an anti-freezing heat transfer fluids in cold climatic regions. Nanofluids are prepared by dispersing 50 nm diameter of CuO nanoparticles in the base fluid. Experiments are conducted using CuO nanofluids with 0.025%, 0.1% and 0.5% volume concentration in the Reynolds numbers ranging from 1000 < Re < 10000 and considerable heat transfer enhancement in CuO nanofluids is observed. The effect of twisted tape inserts with twist ratios in the range of 0 < H/D < 15 on nanofluids is studied and further heat transfer augmentation is noticed. The increment in the pressure drop in the CuO nanofluids over the base fluid is negligible but the experimental results have shown a significant increment in the convective heat transfer coefficient of CuO nanofluids. The convective heat transfer coefficient increased up to 27.95% in the 0.5% CuO nanofluid in plain tube and with a twisted tape insert of H/D = 5 it is further increased to 76.06% over the base fluid at a particular Reynolds number. The friction factor enhancement of 10.08% is noticed and increased to 26.57% with the same twisted tape, when compared with the base fluid friction factor at the same Reynolds number. Based on the experimental data obtained, generalized regression equations are developed to predict Nusselt number and friction factor.     

Effect of particle size on the convective heat transfer in nanofluid in the developing region

An experimental investigation on the convective heat transfer characteristics in the developing region of tube flow with constant heat flux is carried out with alumina–water nanofluids. The primary objective is to evaluate the effect of particle size on convective heat transfer in laminar developing region. Two particle sizes were used, one with average particle size off 45 nm and the other with 150 nm. It was observed that both nanofluids showed higher heat transfer characteristics than the base fluid and the nanofluid with 45 nm particles showed higher heat transfer coefficient than that with 150 nm particles. It was also observed that in the developing region, the heat transfer coefficients show higher enhancement than in the developed region. Based on the experimental results a correlation for heat transfer in the developing region has been proposed for the present range of nanofluids.     

Effect of rotating cylinder on heat transfer in a square enclosure filled with nanofluids

Convective heat transfer in a differentially heated square enclosure with an inner rotating cylinder is studied theoretically. The free space between the cylinder and the enclosure walls is filled with water–Ag, water–Cu, water–Al₂O₃ or water–TiO₂ nanofluids. The governing equations are formulated for velocity, pressure and temperature formulation and are modeled in COMSOL, a partial differential equation (PDE) solver based on the Galerkin finite element method (GFEM). The governing parameters considered are the solid volume fraction, 0.0 ? ? ? 0.05, the cylinder radius, 0 ? R ? 0.3 and the angular rotational velocity, ?1000 ? Ω ? 1000. The results are presented to show the effect of these parameters on the heat transfer and fluid flow characteristics. It is found that the strength of the flow circulation is much stronger for a higher nanoparticle concentration, a better thermal conductivity value and a smaller cylinder with a faster, negative rotation. The maximum heat transfer are obtained at a high nanoparticle concentration with a good conductivity value, a slow positive rotation and a moderate cylinder size located in the center of the enclosure.     

Experimental investigation of oxide nanofluids laminar flow convective heat transfer

In the present investigation nanofluids containing CuO and Al₂O₃ oxide nanoparticles in water as base fluid in different concentrations produced and the laminar flow convective heat transfer through circular tube with constant wall temperature boundary condition were examined. The experimental results emphasize that the single phase correlation with nanofluids properties (Homogeneous Model) is not able to predict heat transfer coefficient enhancement of nanofluids. The comparison between experimental results obtained for CuO / water and Al₂O₃ / water nanofluids indicates that heat transfer coefficient ratios for nanofluid to homogeneous model in low concentration are close to each other but by increasing the volume fraction, higher heat transfer enhancement for Al₂O₃ / water can be observed.     

Experimental investigation and development of new correlation for thermal conductivity and viscosity of BioGlycol/water based SiO2 nanofluids

Nanofluids are a new class of engineered heat transfer fluids which exhibit superior thermophysical properties and have potential applications in numerous important fields. In this study, nanofluids have been prepared by dispersing SiO₂ nanoparticles in different base fluids such as 20:80% and 30:70% by volume of BioGlycol (BG)/water (W) mixtures. Thermal conductivity and viscosity experiments have been conducted in temperatures between 30 °C and 80 °C and in volume concentrations between 0.5% and 2.0%. Results show that thermal conductivity of nanofluids increases with increase of volume concentrations and temperatures. Similarly, viscosity of nanofluid increases with increase of volume concentrations but decreases with increase of temperatures. The maximum thermal conductivity enhancement among all the nanofluids was observed for 20:80% BG/W nanofluid about 7.2% in the volume concentration of 2.0% at a temperature of 70 °C. Correspondingly among all the nanofluids maximum viscosity enhancement was observed for 30:70% BG/W nanofluid about 1.38-times in the volume concentration of 2.0% at a temperature of 70 °C. The classical models and semi-empirical correlations failed to predict the thermal conductivity and viscosity of nanofluids with effect of volume concentration and temperatures. Therefore, nonlinear correlations have been proposed with 3% maximum deviation for the estimation of thermal conductivity and viscosity of nanofluids.     

Effect of nanofluids on reflood heat transfer in a long vertical tube

Experiments were conducted to investigate the effect of nanofluids on reflood heat transfer in a hot vertical tube. The nanofluids, which are produced by dispersing nano-sized particles in traditional base fluids such as water, ethylene glycol, and engine oil, are expected to have a reasonable potential to enhance a heat transfer. 0.1 volume fraction (%) Al₂O₃/water nanofluid was prepared by two-step method and 0.1 volume fraction (%) carbon nano colloid (CNC) was prepared by the process self-dispersing by carboxyl formed particle surface. Transmission electron microscopy (TEM) images are acquired to characterize the shape and size of Al₂O₃ and graphite nanoparticles. The dispersion behavior of nanofluids was investigated with zeta potential values. And then, the reflood tests have been performed using water and nanofluids. We have observed a more enhanced cooling performance in the case of the nanofluid reflood. Consequently, the cooling performance is enhanced more than 13 s and 20 s for Al₂O₃/water nanofluid and CNC.     

Heat transfer and friction factor of water based TiO2 and SiO2 nanofluids under turbulent flow in a tube

The heat transfer coefficient and friction factor of TiO₂ and SiO₂ water based nanofluids flowing in a circular tube under turbulent flow are investigated experimentally under constant heat flux boundary condition. TiO₂ and SiO₂ nanofluids with an average particle size of 50 nm and 22 nm respectively are used in the working fluid for volume concentrations up to 3.0%. Experiments are conducted at a bulk temperature of 30 °C in the turbulent Reynolds number range of 5000 to 25,000. The enhancements in viscosity and thermal conductivity of TiO₂ are greater than SiO₂ nanofluid. However, a maximum enhancement of 26% in heat transfer coefficients is obtained with TiO₂ nanofluid at 1.0% concentration, while SiO₂ nanofluid gave 33% enhancement at 3.0% concentration. The heat transfer coefficients are lower at all other concentrations. The particle concentration at which the nanofluids give maximum heat transfer has been determined and validated with property enhancement ratio. It is observed that the pressure drop is directly proportional to the density of the nanoparticle.     

Thermophysical properties and heat transfer performance of Al2O3/R-134a nanorefrigerants

The past decade has seen the rapid development of nanofluids science in many aspects. In recent years, refrigerant-based nanofluids have been introduced as nanorefrigerants due to their significant effects over heat transfer performance. This study investigates the thermophysical properties, pressure drop and heat transfer performance of Al₂O₃ nanoparticles suspended in 1, 1, 1, 2-tetrafluoroethane (R-134a). Suitable models from existing studies have been used to determine the thermal conductivity and viscosity of the nanorefrigerants for the nanoparticle concentrations of 1 to 5 vol.%. The pressure drop, pumping power and heat transfer coefficients of nanorefrigerant in a horizontal smooth tube have also been investigated with the same particle concentration at constant velocity of 5 m/s and uniform mass flux of 100 kg/m² s. In this study, the thermal conductivity of Al₂O₃/R-134a nanorefrigerant increased with the augmentation of particle concentration and temperature however, decreased with particle size intensification. In addition, the results of viscosity, pressure drop, and heat transfer coefficients of the nanorefrigerant show a significant increment with the increase of volume fractions. Therefore, optimal particle volume fraction is important to be considered in producing nanorefrigerants that can enhance the performance of refrigeration systems.     

Nanofluid convective heat transfer in a parallel-disk system

Inherently low thermal conductivities of basic fluids form a primary limitation in high-performance cooling which is an essential requirement for numerous thermal systems and micro-devices. Nanofluids, i.e., dilute suspensions of, say, metal-oxide nanoparticles in a liquid, are a new type of coolants with better heat transfer performances than their pure base fluids alone. Using a new, experimentally validated model for the thermal conductivity of nanofluids, numerical simulations have been executed for alumina-water nanofluid flow with heat transfer between parallel disks. The results indicate that, indeed, nanofluids are promising new coolants when compared to pure water. Specifically, smoother mixture flow fields and temperature distributions can be achieved. More importantly, given a realistic thermal load, the Nusselt number increases with higher nanoparticle volume fraction, smaller nanoparticle diameter, reduced disk-spacing, and, of course, larger inlet Reynolds number, expressed in a novel form as Nu = Nu(Re and Br). Fully-developed flow can be assumed after a critical radial distance, expressed in a correlation R_crit = fct(Re), has been reached and hence analytic solutions provide good approximations. Nanofluids reduce the system’s total entropy generation rate while hardly increasing the required pumping power for any given Re_in. Specifically, minimization of total entropy generation allows for operational and geometric system-optimization in terms of S_gen = fct (Re and δ).     

Thermal and fluid dynamic behaviors of confined laminar impinging slot jets with nanofluids

Heat transfer enhancement technologies play an important role in research and industrial fields; thus, they have been widely applied to many applications as in refrigeration, automotive, aerospace, and process industry. For example, heat transfer can be passively enhanced by increasing the thermal conductivity of the working fluids, adopting nanofluids, or actively by employing impinging jets.In this paper a numerical analysis on confined impinging slot jets working with pure water or water/Al₂O₃ based nanofluids is presented. The flow is laminar and a constant uniform temperature is applied on the target surface. The single-phase model approach has been adopted in order to describe the nanofluid behavior and different particle volume concentrations have been considered. Moreover, simulations have been performed for different geometric ratios in order to take into account the confining effects and Reynolds numbers. The behavior of the system has been analyzed in terms of average and local convective heat transfer coefficient, Nusselt number, and required pumping power profiles. Correlations for stagnation point and average Nusselt number for 100 ≤ Re ≤ 400, 0% ≤ ϕ ≤ 5% and 4 ≤ H/W ≤ 10 are provided.     

Thermal evaluation of nanofluids in heat exchangers

Nanofluids, suspensions of nanoparticles (less than 100 nm) in a basefluid, have shown enhanced heat transfer characteristics. In this study, thermal performances of nanofluids in industrial type heat exchangers are investigated. Three mass particle concentrations of 2%, 4%, and 6% of silicon dioxide–water (SiO₂–water) nanofluids are formulated by dispersing 20 nm diameter nanoparticles in distilled water. Experiments are conducted to compare the overall heat transfer coefficient and pressure drop of water vs. nanofluids in laboratory-scale plate and shell-and-tube heat exchangers. Experimental results show both augmentation and deterioration of heat transfer coefficient for nanofluids depending on the flow rate and nanofluid concentration through the heat exchangers. This trend could be explained by the counter effect of the changes in thermo-physical properties of fluids together with the fouling on the contact surfaces in the heat exchangers. The measured pressure drop while using nanofluids show an increase when compared to that of basefluid which could limit the use of nanofluids in industrial applications.     

Numerical research of nature convective heat transfer enhancement filled with nanofluids in rectangular enclosures

Heat transfer enhancement utilizing nanofluids in a two-dimensional enclosure is investigated for various pertinent parameters. The Khanafer's model is used to analyze heat transfer performance of nanofluids inside an enclosure taking into account the solid particle dispersion. Transport equations are model by a stream function-vorticity formulation and are solved numerically by finite-difference approach. Based upon the numerical predictions, the effects of Rayleigh number (Ra) and aspect ratio (AR) on the flow pattern and energy transport within the thermal boundary layer are presented. The diameter of the nanoparticle d_p is taken as 10 nm in nanofluids. The buoyancy parameter is 10³ ≤ Ra ≤ 10⁶ and aspect ratios (AR) of two-dimensional enclosure are 1/2, 1, 2. Results show that increasing the buoyancy parameter and volume fraction of nanofluids cause an increase in the average heat transfer coefficient. Finally, the empirical equation was built between average Nusselt number and volume fraction.     

Numerical investigation on heat transfer and friction factor characteristics of laminar and turbulent flow in an elliptic annulus utilizing nanofluid

In this paper, a numerical investigation on heat transfer performance and flow fields of different nanofluids flows through elliptic annulus in a laminar and turbulent flow regimes. The three-dimensional continuity, Navier–Stokes and energy equations are solved by using finite volume method (FVM) and the SIMPLE algorithm scheme is applied to examine the effects of laminar and turbulent flow on heat transfer characteristics. This study evaluates the effects of four different types of nanoparticles, Al₂O₃, CuO, SiO₂ and ZnO, with different volume fractions (0.5–4%) and diameters (25–80 nm) under constant heat flux boundary condition using water as a base fluid were used. The Reynolds number of laminar flow was in the range of 200 ≤ Re ≤ 1500, while for turbulent flow it was in the range of 4000 ≤ Re ≤ 10,000. The results have shown that SiO₂–water nanofluid has the highest Nusselt number, followed by ZnO–water, CuO–water, Al₂O₃–water, and lastly pure water. The Nusselt number for all cases increases with the volume fraction but it decreases with the rise in the diameter of nanoparticles. In all configurations, the Nusselt number increases with Reynolds number. It is found that the glycerine–SiO₂ shows the best heat transfer enhancement compared with other tested base fluids.     

Thermal conductivity of ethylene glycol and water mixture based Fe3O4 nanofluid

Thermal conductivity of ethylene glycol and water mixture based Fe₃O₄ nanofluid has been investigated experimentally. Magnetic Fe₃O₄ nanoparticles were synthesized by chemical co-precipitation method and the nanofluids were prepared by dispersing nanoparticles into different base fluids like 20:80%, 40:60% and 60:40% by weight of the ethylene glycol and water mixture. Experiments were conducted in the temperature range from 20 °C to 60 °C and in the volume concentration range from 0.2% to 2.0%. Results indicate that the thermal conductivity increases with the increase of particle concentration and temperature. The thermal conductivity is enhanced by 46% at 2.0 vol.% of nanoparticles dispersed in 20:80% ethylene glycol and water mixture compared to other base fluids. The theoretical Hamilton–Crosser model failed to predict the thermal conductivity of the nanofluid with the effect of temperature. A new correlation is developed for the estimation of thermal conductivity of nanofluids based on the experimental data.     

Heat transfer enhancement using Al2O3–water nanofluid for an electronic liquid cooling system

We have experimentally investigated the behaviour and heat transfer enhancement of a particular nanofluid, Al₂O₃ nanoparticle–water mixture, flowing inside a closed system that is destined for cooling of microprocessors or other electronic components. Experimental data, obtained for turbulent flow regime, have clearly shown that the inclusion of nanoparticles into distilled water has produced a considerable enhancement of the cooling block convective heat transfer coefficient. For a particular nanofluid with 6.8% particle volume concentration, heat transfer coefficient has been found to increase as much as 40% compared to that of the base fluid. It has also been found that an increase of particle concentration has produced a clear decrease of the heated component temperature. Experimental data have clearly shown that nanofluid with 36 nm particle diameter provides higher heat transfer coefficients than the ones of nanofluid with 47 nm particle size.     

The particle thermal conductivity influence of nanofluids on thermal performance of the microtubes

The paper presents the numerical analysis on microchannel laminar heat transfer and fluid flow of nanofluids in order to evaluate the suitable thermal conductivity of the nanoparticles that results in superior thermal performances compared to the base fluid. The diameter ratio of the micro-tube was D_i/D_o = 0.3/0.5 mm with a tube length L = 100 mm in order to avoid the heat dissipation effect. The heat transfer rate was fixed to Q = 2 W. The water based Al₂O₃, TiO₂ and Cu nanofluids were considered with various volume concentrations ϕ = 1,3 and 5% and two diameters of the particles d_p = 13 nm and 36 nm. The analysis is based on a fixed Re and pumping power Π, in terms of average heat transfer coefficient and maximum temperature of the substrate. The results reveal that only the nanofluids with particles having very high thermal conductivity (λ_Cu = 401 W/m K) are justified for using in microcooling systems. Moreover, the analysis is sensitive to both the comparison criteria (Re or Π) and heat transfer parameters (h_ave or t_max).     

Stabilizer effect on CHF and boiling heat transfer coefficient of alumina/water nanofluids

We measured the critical heat flux (CHF) and boiling heat transfer coefficient (BHTC) of water-based Al₂O₃ (alumina) nanofluids. To elucidate the stabilizer effect on CHF and BHTC of alumina/water nanofluids, a polyvinyl alcohol (PVA) was used as a stabilizer. The plate copper heater (10 × 10 mm²) is used as the boiling surface and the concentration of alumina nanoparticle varies 0–0.1 vol.%. The results show that the BHTC of the nanofluids becomes lower than that of the base fluid as the concentration of nanoparticles increases while CHF of it becomes higher. It is found that the increase of CHF is directly proportional to the effective boiling surface area and the reduction of BHTC is mainly attributed to the blocking of the active nucleation cavity and the increase of the conduction resistance by the nanoparticle deposition on the boiling surface.     

Experimental studies on thermal conductivity of blends of ethylene glycol-water-based TiO2 nanofluids

A set of three nanofluids of different blends were prepared with ethylene glycol–water and TiO₂ nanoparticles and are characterized for thermal conductivity as a function of temperature and volume concentration of nanoparticles. The measurements were taken in the temperature range from 30 °C to 70 °C, which happens to be most widely used range of temperature for many cooling applications in heat transfer equipment. Nanofluids were prepared by dispersing the nanoparticles in base fluids such as (1) water, (2) ethylene glycol plus water in the ratio of 40%:60% and 3) ethylene glycol plus water in the ratio of 50%:50% by weight. Based on the experimental results, it is observed that the thermal conductivity of TiO₂ nanofluids, considered in the present investigation, increases with increase in percentage of volume concentration of TiO₂ and also with temperature. Current experimental investigation presents valuable data on the measured thermal conductivity of TiO₂ nanofluids for very low volume concentrations from 0.2% to 1.0% of nanoparticles in the temperature range of 30 °C–70 °C.