Effect of Co3(PO4)2 coating on Li[Co0.1Ni0.15Li0.2Mn0.55]O2 cathode material for lithium rechargeable batteries

To prepare a high-capacity cathode material with improved electrochemical performance for lithium rechargeable batteries, Co₃(PO₄)₂ nanoparticles are coated on the surface of powdered Li[Co_0.1Ni_0.15Li_0.2Mn_0.55]O₂, which is synthesized by a simple combustion method. The coated powder prepared under proper conditions for Co₃(PO₄)₂ content and annealing temperature shows an optimum coating layer that consists of a Li_xCoPO₄ phase formed by reaction with lithium impurities during heat treatment. A sample coated with 3 wt.% Co₃(PO₄)₂ and annealed at 800 °C proves to be the best in terms of specific capacity, cycle performance and rate capability. Thermal stability is also enhanced by the coating, as demonstrated a decrease in the onset temperature and/or the heat generated during thermal runaway.     

Physical and electrochemical properties of spherical Li1+x(Ni1/3Co1/3Mn1/3)1−xO2 cathode materials

A (Ni_1/3Co_1/3Mn_1/3)CO₃ precursor with an uniform, spherical morphology was prepared by coprecipitation using a continuously stirred tank reactor method. The as-prepared spherical (Ni_1/3Co_1/3Mn_1/3)CO₃ precursor served to produce dense, spherical Li_1+x(Ni_1/3Co_1/3Mn_1/3)_1−xO₂ (0 ≤ x ≤ 0.15) cathode materials. These Li-rich cathodes were also prepared by a second synthesis route that involved the use of an M₃O₄ (M = Ni_1/3Co_1/3Mn_1/3) spinel compound, itself obtained from the carbonate (Ni_1/3Co_1/3Mn_1/3)CO₃ precursor. In both cases, the final Li_1+x(Ni_1/3Co_1/3Mn_1/3)_1−xO₂ products were highly uniform, having a narrow particle size distribution (10-μm average particle size) as a result of the homogeneity and spherical morphology of the starting mixed-metal carbonate precursor. The rate capability of the Li_1+x(Ni_1/3Co_1/3Mn_1/3)_1−xO₂ electrode materials, which was significantly improved with increased lithium content, was found to be better in the case of the denser materials made from the spinel precursor compound. This result suggests that spherical morphology, high density, and increased lithium content were key factors in enabling the high rate capabilities, and hence the power performances, of the Li-rich Li_1+x(Ni_1/3Co_1/3Mn_1/3)_1−xO₂ cathodes.     

Surface modification of Li[Ni0.3Co0.4Mn0.3]O2 cathode by Li-La-Ti-O coating

A Li[Ni_0.3Co_0.4Mn_0.3]O₂ cathode is modified by applying a Li-La-Ti-O coating using the hydrothermal method. The coated Li[Ni_0.3Co_0.4Mn_0.3]O₂ is characterized by X-ray diffraction analysis, scanning electron microscopy, energy-dispersive spectrometry, transmission electron microscopy, and differential scanning calorimetry. The Li-La-Ti-O coating layer is formed as crystalline (perovskite structure) or amorphous phase depending on the heating temperature. The Li-La-Ti-O coated Li[Ni_0.3Co_0.4Mn_0.3]O₂ electrode has better rate capability than the pristine electrode. In particular, the rate capability is significantly associated with heating temperature; this is probably due to the phase of the coating layer. It appears that the Li-La-Ti-O coating of amorphous phase is superior to that of crystalline phase for obtaining enhanced rate capability of the coated samples. The thermal stability and cyclic performance of the Li[Ni_0.3Co_0.4Mn_0.3]O₂ electrode are also improved by Li-La-Ti-O coating. These improvements indicate that the Li-La-Ti-O coating is effective in suppressing the chemical and structural instabilities of Li[Ni_0.3Co_0.4Mn_0.3]O₂.     

Cation ordering in the layered Li1+x(Ni0.425Mn0.425Co0.15)1 − xO2 materials (x = 0 and 0.12)

The layered Li_1+x(Ni_0.425Mn_0.425Co_0.15)_1 − xO₂ (x = 0 and 0.12) materials were prepared by a coprecipitation method. Their structure was investigated using the combination of X-ray and electron diffraction experiments. For both materials (x = 0 and 0.12), the electron diffraction patterns revealed an in-plane √3a_hex. × √3a_hex. superstructure in agreement with the ordering of the Li⁺, Ni²⁺, Ni³⁺, Mn⁴⁺ and Co³⁺ ions in the transition metal layers. The stoichiometry of these materials was not in agreement with an ideal ordering: the possible presence of point defects or of a domain microstructure was thus discussed. Electron diffraction also revealed that these ordered layers were slightly correlated along the c_hex. axis for both materials.     

Influence of lithium content on high rate cycleability of layered Li1+xNi0.30Co0.30Mn0.40O2 cathodes for high power lithium-ion batteries

Layered Li_1+xNi_0.30Co_0.30Mn_0.40O₂ (x = 0, 0.05, 0.10, 0.15) materials have been synthesized using citric acid assisted sol-gel method. The materials with excess lithium showed distinct differences in the structure and the charge and discharge characteristics. The rate capability tests were performed and compared on Li_1+xNi_0.30Co_0.30Mn_0.40O₂ (x = 0, 0.05, 0.10, 0.15) cathode materials. Among these materials, Li_1.10Ni_0.30Co_0.30Mn_0.40O₂ cathode demonstrated higher discharge capacity than that of the other cathodes. Upon extended cycling at 1C and 8C, Li_1.10Ni_0.30Co_0.30Mn_0.40O₂ showed better capacity retention when compared to other materials with different lithium content. Li_1.10Ni_0.30Co_0.30Mn_0.40O₂ exhibited 93 and 90% capacity retention where as Li_1.05Ni_0.30Co_0.30Mn_0.40O₂, Li_1.15Ni_0.30Co_0.30Mn_0.40O₂, and Li_1.00Ni_0.30Co_0.30Mn_0.40O₂ exhibited only 84, 71, and 63% (at 1C), and 79, 66 and 40% (at 10C) capacity retention, respectively, after 40 cycles. The enhanced high rate cycleability of Li_1.10Ni_0.30Co_0.30Mn_0.40O₂ cathode is attributed to the improved structural stability due to the formation of appropriate amount of Li₂MnO₃-like domains in the transition metal layer and decreased Li/Ni disorder (i.e., Ni content in the Li layer).     

Synthesis and electrochemical properties of lithium non-stoichiometric Li1+x(Ni1/3Co1/3Mn1/3)O2+δ prepared by a spray drying method

Lithium non-stoichiometric Li[Li_x(Ni_1/3Co_1/3Mn_1/3)_1−x]O₂ materials (0 ≤ x ≤ 0.17) were synthesized using a spray drying method. The electrochemical properties and structural stabilities of the synthesized materials were investigated. The synthesized materials exhibited a hexagonal structure in all the x-value and the lattice parameters of the materials were gradually decreased with increasing x-value due to an increasing amount of Ni³⁺ ions for charge compensation. The capacity retention ability and rate capability of the stoichiometric Li(Ni_1/3Co_1/3Mn_1/3)O₂ material were improved by increasing x-value, the so-called overlithiation. We found that the overlithiated materials could keep more structural integrity than the stoichiometric one during electrochemical cyclings, which could be one of reasons for a better electrochemical properties of the overlithiated materials.     

Thermal stability of LiPF6-based electrolyte and effect of contact with various delithiated cathodes of Li-ion batteries

Thermal stability of LiPF₆-based electrolyte (1 M LiPF₆/EC + DMC) was studied by in-situ FTIR spectroscopy and C80 calorimetry, which indicated that the electrolyte underwent furious polymerization and decomposition reactions and sharp heat flow was generated below 225 °C. The thermal stability of the electrolyte in contact with various delithiated cathodes (Li_xCoO₂, Li_xNi_0.8Co_0.15Al_0.05O₂, Li_xNi_1/3Co_1/3Mn_1/3O₂, Li_xMn₂O₄, Li_xNi_0.5Mn_0.5O₂, Li_xNi_0.5Mn_1.5O₄ and Li_xFePO₄) was also investigated by C80 calorimetry. The results show that the cathode materials except for Li_xFePO₄ usually have an enhancement effect on the decomposition of the electrolyte, but Li_xFePO₄ exhibits a suppression effect on the reactions of the electrolyte. Li_xFePO₄ is found to be with excellent thermal stability. Among the other cathodes, Li_xCoO₂, Li_xNi_0.8Co_0.15Al_0.05O₂, Li_xNi_0.5Mn_0.5O₂ and Li_xNi_0.5Mn_1.5O₄ promote the decomposition of electrolyte by releasing oxygen and thus considered not favorable for safety, but Li_xNi_1/3Co_1/3Mn_1/3O₂ with a lesser reaction heat and Li_xMn₂O₄ with even less heat flow in the low temperature range (50-225 °C) are believed as promising cathodes for better safety. By comparing X-ray diffraction (XRD) patterns of these cathode materials at room temperature and those heated to 300 °C in the presence of the electrolyte, we have found that Li_xFePO₄ only has experienced tiny structure change, which is greatly different from the other cathode materials.     

Characterization of LiCoO2 coated Li1.05Ni0.35Co0.25Mn0.4O2 cathode material for lithium secondary cells

In this study, nano-crystalline LiCoO₂ was coated onto the surface of Li_1.05Ni_0.35Co_0.25Mn_0.4O₂ powders via sol–gel method. The influence of the coating on the electrochemical behavior of Li_1.05Ni_0.35Co_0.25Mn_0.4O₂ is discussed. The surface morphology was characterized by transmission electron microscopy (TEM). Nano-crystallized LiCoO₂ was clearly observed on the surfaces of Li_1.05Ni_0.35Co_0.25Mn_0.4O₂. The phase and structural changes of the cathode materials before and after coating were revealed by X-ray diffraction spectroscopy (XRD). It was found that LiCoO₂ coated Li_1.05Ni_0.35Co_0.25Mn_0.4O₂ cathode material exhibited distinct surface morphology and lattice constants. Cyclic voltammetry (2.8–4.6 V versus Li/Li⁺) shows that the characteristic voltage transitions on cycling exhibited by the uncoated material are suppressed by the 7 wt.% LiCoO₂ coating. This behavior implies that LiCoO₂ inhibits structural change of Li_1.05Ni_0.35Co_0.25Mn_0.4O₂ or reaction with the electrolyte on cycling. In addition, the LiCoO₂ coating on Li_1.05Ni_0.35Co_0.25Mn_0.4O₂ significantly improves the rate capability over the range 0.1–4.0C. Comparative data for the coated and uncoated materials are presented and discussed.     

The electrochemical property of ZrFx-coated Li[Ni1/3Co1/3Mn1/3]O2 cathode material

Electrochemical and thermal properties of pristine and ZrF_x-coated Li[Ni_1/3Co_1/3Mn_1/3]O₂ cathode materials are compared. The hydrothermal method is introduced for the fabrication of a uniform coating layer. The formation of a compact coating layer on the surface of pristine powder is observed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). From TEM-EDS and XPS analysis, it is inferred that the coating layer is ZrO_xF_y (zirconium oxyfluoride) form. The coated Li[Ni_1/3Co_1/3Mn_1/3]O₂ electrodes have better rate capability and cyclic performance at high temperature compared with the pristine electrode. The thermal stability of the Li[Ni_1/3Co_1/3Mn_1/3]O₂ electrode is also enhanced by the ZrF_x coating. Such enhancements are due to the presence of a stable coating layer, which effectively suppresses the chemical instability ascribed to surface reaction between electrode and electrolyte.     

Structural and transport properties of layered Li1+x(Mn1/3Co1/3Ni1/3)1−xO2 oxides prepared by a soft chemistry method

In this work structural and transport properties of layered Li_1+x(Mn_1/3Co_1/3Ni_1/3)_1−xO₂ oxides (x = 0; 0.03; 0.06) prepared by a “soft chemistry” method are presented. The excessive lithium was found to significantly improve transport properties of the materials, a corresponding linear decrease of the unit cell parameters was observed. The electrical conductivity of Li_1.03(Mn_1/3Co_1/3Ni_1/3)_0.97O₂ composition was high enough to use this material in a form of a pellet, without any additives, in lithium batteries and characterize structural and transport properties of deintercalated Li_1.03−y(Mn_1/3Co_1/3Ni_1/3)_0.97O₂ compounds. For deintercalated samples a linear increase of the lattice parameter c together with a linear decrease of the parameter a with the increasing deintercalation degree occurred, but only up to 0.4-0.5 mol of extracted lithium. Further deintercalation showed a reversal of the trend. Electrical conductivity measurements performed of Li_1.03−y(Mn_1/3Co_1/3Ni_1/3)_0.97O₂ samples (y = 0.1; 0.3; 0.5; 0.6) showed an ongoing improvement, almost two orders of magnitude, in relation to the starting composition. Additionally, OCV measurements, discharge characteristics and lithium diffusion coefficient measurements were performed for Li/Li⁺/Li_1.03−y(Mn_1/3Co_1/3Ni_1/3)_0.97O₂ cells.     

Structural and electrochemical characterization of xLi[Li1/3Mn2/3]O2·(1 − x)Li[Ni1/3Mn1/3Co1/3]O2 (0 ≤ x ≤ 0.9) as cathode materials for lithium ion batteries

A series of cathode materials with molecular notation of xLi[Li_1/3Mn_2/3]O₂·(1 − x)Li[Ni_1/3Mn_1/3Co_1/3]O₂ (0 ≤ x ≤ 0.9) were synthesized by combination of co-precipitation and solid state calcination method. The prepared materials were characterized by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) techniques, and their electrochemical performances were investigated. The results showed that sample 0.6Li[Li_1/3Mn_2/3]O₂·0.4Li[Ni_1/3Mn_1/3Co_1/3]O₂ (x = 0.6) delivers the highest capacity and shows good capacity-retention, which delivers a capacity ∼250 mAh g⁻¹ between 2.0 and 4.8 V at 18 mA g⁻¹.     

On the LiNi0.2Mn0.2Co0.6O2 positive electrode material

Layered LiNi_0.2Mn_0.2Co_0.6O₂ phase, belonging to a solid solution between LiNi_1/2Mn_1/2O₂ and LiCoO₂ most commercialized cathodes, was prepared via the combustion method at 900 °C for a short time (1 h). Structural, electrochemical and magnetic properties of this material were investigated. Rietveld analysis of the XRD pattern shows this compound as having the α-NaFeO₂ type structure (S.G. R-3m; a = 2.8399(2) ?; c = 14.165(1) ?) with almost none of the well-known Li/Ni cation disorder. SQUID measurements clearly indicate that the studied compound consists of Ni²⁺, Co³⁺ and Mn⁴⁺ ions in the crystal structure. X-ray analysis of the chemically delithiated Li_xNi_0.2Mn_0.2Co_0.6O₂ phases reveals that the rhombohedral symmetry was maintained during Li-extraction, confirmed by the monotonous variation of the potential-composition curve of the Li//Li_xNi_0.2Mn_0.2Co_0.6O₂ cell. LiNi_0.2Mn_0.2Co_0.6O₂ cathode has a discharge capacity of ∼160 mAh g⁻¹ in the voltage range 2.7-4.3 V corresponding to the extraction/insertion of 0.6 lithium ion with very low polarization. It exhibits a stable capacity on cycling and good rate capability in the rate range 0.2-2 C. The almost 2D structure of this cathode material, its good electrochemical performances and its relatively low cost comparing to LiCoO₂, make this material very promising for applications.     

Effect of Cr doping on the structural,electrochemical properties of Li[Li0.2Ni0.2−x/2Mn0.6−x/2Crx]O2 (x = 0, 0.02, 0.04, 0.06, 0.08) as cathode materials for lithium secondary batteries

Prospective positive-electrode (cathode) materials for a lithium secondary battery, viz., Li[Li_0.2Ni_0.2−x/2Mn_0.6−x/2Cr_x]O₂ (x = 0, 0.02, 0.04, 0.06, 0.08), were synthesized using a solid-state pyrolysis method. The structural and electrochemical properties were examined by means of X-ray diffraction, cyclic voltammetry, SEM and charge–discharge tests. The results demonstrated that the powders maintain the α-NaFeO₂-type layered structure regardless of the chromium content in the range x ≤ 0.08. The Cr doping of x = 0.04 showed improved capacity and rate capability comparing to undoped Li[Li_0.2Ni_0.2Mn_0.6]O₂. ac impedance measurement showed that Cr-doped electrode has the lower impedance value during cycling. It is considered that the higher capacity and superior rate capability of Cr-doping samples would be ascribed to the reduced resistance of the electrode during cycling.     

Development of high power lithium-ion batteries: Layer Li[Ni0.4Co0.2Mn0.4]O2 and spinel Li[Li0.1Al0.05Mn1.85]O4

Layer Li[Ni_0.4Co_0.2Mn_0.4]O₂ and lithium excess spinel Li[Li_0.1Al_0.05Mn_1.85]O₄ were compared as positive electrode materials for high power lithium-ion batteries. Physical properties were examined by Rietveld refinement of X-ray diffraction pattern and scanning electron microscopic studies. From continuous charge and discharge tests at higher currents and different temperature environments using 3Ah class lithium-ion batteries, it was found that both materials presented plausible battery performances such as rate capability, cyclability at 60 °C at elevated temperature, and low temperature properties as well.     

Minimization of the cation mixing in Li1+x(NMC)1−xO2 as cathode material

Li_1+x(Ni_1/3Mn_1/3Co_1/3)_1−xO₂ layered materials were synthesized by the co-precipitation method with different Li/M molar ratios (M = Ni + Mn + Co). Elemental titration evaluated by inductively coupled plasma spectrometry (ICP), structural properties studied by X-ray diffraction (XRD), Rietveld analysis of XRD data, scanning electron microscopy (SEM) and magnetic measurements carried out by superconducting quantum interference devices (SQUID) showed the well-defined α-NaFeO₂ structure with cationic distribution close to the nominal formula. The Li/Ni cation mixing on the 3b Wyckoff site of the interlayer space was consistent with the structural model [Li_1−yNi_y]_3b[Li_x+yNi_{(1−x)/3−y}Mn_(1−x)/3Co_(1−x)/3]_3aO₂ (x = 0.02, 0.04) and was very small. Both Rietveld refinements and magnetic measurements revealed a concentration of Ni²⁺-3b ions lower than 2%; moreover, for the optimized sample synthesized at Li/M = 1.10, only 1.43% of nickel ions were located into the Li sublattice. Electrochemical properties were investigated by galvanostatic charge-discharge cycling. Data obtained with Li_1+x(Ni_1/3Mn_1/3Co_1/3)_1−xO₂ reflected the high degree of sample optimization. An initial discharge capacity of 150 mAh g⁻¹ was delivered at 1 C-rate in the cut-off voltage of 3.0-4.3 V. More than 95% of its initial capacity was retained after 30 cycles at 1 C-rate. Finally, it is demonstrated that a cation mixing below 2% is considered as the threshold for which the electrochemical performance does not change for Li_1+x(Ni_1/3Mn_1/3Co_1/3)_1−xO₂.     

The influence of compositional change of 0.3Li2MnO3·0.7LiMn1−xNiyCo0.1O2 (0.2 ≤ x ≤ 0.5, y = x − 0.1) cathode materials prepared by co-precipitation

Cathode materials prepared by a co-precipitation are 0.3Li₂MnO₃·0.7LiMn_1−xNi_yCo_0.1O₂ (0.2 ≤ x ≤ 0.4) cathode materials with a layered-spinel structure. In the voltage range of 2.0-4.6 V, the cathodes show more than one redox reaction peak during its cyclic voltammogram. The Li/0.3Li₂MnO₃·0.7LiMn_1−xNi_yCo_0.1O₂ (x = 0.3, y = 0.2) cell shows the initial discharge capacity of about 200 mAh g⁻¹. However, when x = 0.2 and y = 0.1, the cell exhibits a rapid decrease in discharge capacity and poor cycle life.     

Synthesis and characterization of Li3V(2 − 2x/3)Mgx(PO4)3/C cathode material for lithium-ion batteries

Li₃V_{(2 − 2x/3)}Mg_x(PO₄)₃/C (x = 0, 0.15, 0.30, 0.45) composites have been synthesized by the sol-gel assisted solid state method, using adipic acid C₆H₁₀O₄ (hexanedioic acid) as carbon source. The particle size of the composites is ∼1 μm. During the pyrolysis process, Li₃V_{(2 − 2x/3)}Mg_x(PO₄)₃/C network structure is formed. The effect of Mg²⁺ doped on the electrochemical properties of Li₃V₂(PO₄)₃/C positive materials has been studied. Li₃V_1.8Mg_0.30(PO₄)₃/C as the cathode materials of Li-ion batteries, the retention rate of discharge capacity is 91.4% (1 C) after 100 cycles. Compared with Li₃V₂(PO₄)₃/C, Li₃V_{(2 − 2x/3)}Mg_x(PO₄)₃/C composites have shown enhanced capacity and retention rate capability. The long-term cycles and ex situ XRD tests disclose that Li₃V_1.8Mg_0.30(PO₄)₃ exhibits higher structural stability than the undoped system.     

Structural changes and thermal stability of charged LiNi1/3Co1/3Mn1/3O2 cathode material for Li-ion batteries studied by time-resolved XRD

Structural changes and their relationship with thermal stability of charged Li_0.33Ni_1/3Co_1/3Mn_1/3O₂ cathode samples have been studied using time-resolved X-ray diffraction (TR-XRD) in a wide temperature from 25 to 600 °C with and without the presence of electrolyte in comparison with Li_0.27Ni_0.8Co_0.15Al_0.05O₂ cathodes. Unique phase transition behavior during heating is found for the Li_0.33Ni_1/3Co_1/3Mn_1/3O₂ cathode samples: when no electrolyte is present, the initial layered structure changes first to a LiM₂O₄-type spinel, and then to a M₃O₄-type spinel and remains in this structure up to 600 °C. For the Li_0.33Ni_1/3Co_1/3Mn_1/3O₂ cathode sample with electrolyte, additional phase transition from the M₃O₄-type spinel to the MO-type rock salt phase takes place from about 400 to 441 °C together with the formation of metallic phase at about 460 °C. The major difference between this type of phase transitions and that for Li_0.27Ni_0.8Co_0.15Al_0.05O₂ in the presence of electrolyte is the delayed phase transition from the spinel-type to the rock salt-type phase by stretching the temperature range of spinel phases from about 20 to 140 °C. This unique behavior is considered as the key factor of the better thermal stability of the Li_1−xNi_1/3Co_1/3Mn_1/3O₂ cathode materials.     

A modified ZrO2-coating process to improve electrochemical performance of Li(Ni1/3Co1/3Mn1/3)O2

A modified Zr-coating process was introduced to improve the electrochemical performance of Li(Ni_1/3Co_1/3Mn_1/3)O₂. The ZrO₂-coating was carried out on an intermediate, (Ni_1/3Co_1/3Mn_1/3)(OH)₂, rather than on Li(Ni_1/3Co_1/3Mn_1/3)O₂. After a heat treatment process, one part of the Zr covered the surface of Li(Ni_1/3Co_1/3Mn_1/3)O₂ in the form of a Li₂ZrO₃ coating layer, and the other part diffused into the crystal lattice of Li(Ni_1/3Co_1/3Mn_1/3)O₂. A decreasing gradient distribution in the concentration of Zr was detected from the surface to the bulk of Li(Ni_1/3Co_1/3Mn_1/3)O₂ by X-ray photoelectron spectra (XPS). Electrochemical tests indicated that the 1% (Zr/Ni + Co + Mn) ZrO₂-modified Li(Ni_1/3Co_1/3Mn_1/3)O₂ prepared by this process showed better cyclability and rate capability than bare Li(Ni_1/3Co_1/3Mn_1/3)O₂. The result can be ascribed to the special effect of Zr in ZrO₂-modified Li(Ni_1/3Co_1/3Mn_1/3)O₂. The surface coating layer of Li₂ZrO₃ improved the cycle performance, while the incorporation of Zr in the crystal lattice of Li(Ni_1/3Co_1/3Mn_1/3)O₂ modified the rate capability by increasing the lattice parameters. Electrochemical impedance spectra (EIS) results showed that the increase of charge transfer resistance during cycling was suppressed significantly by ZrO₂ modification.     

Effects of fluorine-substitution on the electrochemical behavior of LiFePO4/C cathode materials

The effects of fluorine substitution on the electrochemical properties of LiFePO₄/C cathode materials were studied. Samples with stoichiometric proportion of LiFe(PO₄)_1−xF_3x/C (x = 0.025, 0.05, 0.1) were prepared by adding LiF in the starting materials of LiFePO₄/C. XRD and XPS analyses indicate that LiF was completely introduced into bulk LiFePO₄ structure in LiFe(PO₄)_1−xF_3x/C (x = 0.025, 0.05) samples, while there was still some excess of LiF in LiFe(PO₄)_0.9F_0.3/C sample. The results of electrochemical measurement show that F-substitution can improve the rate capability of these cathode materials. The LiFe(PO₄)_0.9F_0.3/C sample showed the best high rate performance. Its discharge capacity at 10 C rate was 110 mAh g⁻¹ with a discharge voltage plateau of 3.31–3.0 V versus Li/Li⁺. The LiFe(PO₄)_0.9F_0.3/C sample also showed obviously better cycling life at high temperature than the other samples.