Synthesis and characterization of palm‐based resin for UV coating

The production of UV curable acrylated polyol ester prepolymer from palm oil and its downstream products offer potential and promising materials for applications such as polymeric film preparation and coatings. In this study, palm olein polyol was reacted with acrylic acid in the presence of a catalyst and inhibitors via condensation esterification process. The reaction temperature of 80°C and the stirring rate of 400 rpm produce a homogeneous product. Based on iodine value result, the suitable amount of p‐toluene sulfonic acid monohydrate used as catalyst was 3.0% (w/w) of palm olein polyol. Different UV curable formulations have been investigated using the synthesized prepolymers with monomers and a small amount of photoinitiator. Monomers used were 1,6‐hexanediol diacrylate (HDDA) and trimethylolpropane triacrylate (TMPTA) while photoinitiator used was 1‐hydroxy cyclohexyl phenylketone (Irgacure 184). The mixtures were cured to make thin polymeric films under UV radiation with doses between 2 and 14 passes (energy per pass is 0.6 J/cm²). Coating and curing was carried out on glass for pendulum hardness and FTIR analysis. Pendulum hardness of the film prepared using monomer HDDA and the prepolymer previously synthesized using 3.0% catalyst was 24.5%. The radiation dose needed was 14 passes. The highest pendulum hardness of 49.4% was achieved using monomer TMPTA and the prepolymer synthesized using 2.0% catalyst. The radiation dose needed was 10 passes. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Water‐soluble copolymers from functionalized monomers (sodium o‐ and p‐methacryloylaminophenylarsonate): Synthesis and characterization

Copolymers of sodium o‐methacryloylaminophenylarsonate (o‐MAPHA‐Na) 1 and p‐methacrylolylaminophenylarsonate (p‐MAPHA‐Na) 2 with sodium acrylate (AA‐Na) 3 , sodium methacrylate (AM‐Na) 4 and acrylamide (AAD) 5 were prepared by free radical polymerization in aqueous media at 70°C using potassium persulfate (K₂S₂O₈) as the initiator. The total monomer concentration was carried out at 0.5M and the feed ratio ( M₁ : M₂ ) was varied from 10 : 90 to 90 : 10 mol%. The kinetic study was carried out by dilatometric method. The copolymer compositions were calculated by arsenic content in the copolymers. The As content (ppm) was determined by atomic absorption spectrometry (AAS). The reactivity ratios (r₁, r₂) were estimated by the Kelen‐Tüdös linearization method as well as error‐in‐variables method using the computer program RREVM®. In all cases, r₁ < 1 and r₂ > 1, indicating a tendency to form random copolymers. The values suggest that the copolymers contain a larger proportion of comonomer (i.e., AA‐Na, AM‐Na, or AAD). Weight‐average molar masses (M _w) of copolymers were determined by multi‐angle light scattering. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Photocrosslinkable copolymers based on 4‐acryloyloxyphenyl‐3′‐chlorostyryl ketone and methyl methacrylate: synthesis,comonomer reactivity ratios and UV photosensitivity

A new photosensitive acrylate monomer having a pendant chlorocinnamoyl moiety (APCSK) was copolymerized with methyl methacrylate (MMA) in different feed compositions in ethyl acetate solution at 70°C using benzoyl peroxide as a free‐radical initiator. The newly synthesized copolymers were characterized by FTIR, ¹H and ¹³C nuclear magnetic resonance (NMR) spectral techniques, as well as by size‐exclusion chromatography. Their thermal behaviour was assessed by thermogravimetric analysis in air and differential scanning calorimetry under nitrogen atmosphere. The copolymers exhibit no phase separation since there is only one glass transition temperature (T_g) value in the region of copolymer composition studied. The reactivity ratios of the comonomers were calculated by adopting linearization methods such as the Fineman–Ross (F‐R), Kelen–Tudos (K‐T) and extended Kelen–Tudos (ExtK‐T) methods, and by a non‐linear error‐in‐variables model method (EVM) using a computer program (RREVM). The results suggest that MMA is more reactive than APCSK and that their copolymerization leads to the formation of random copolymers. The photosensitivity of the copolymer samples was studied in solution as well as in thin films through UV irradiation. The influence of different factors, including solvent nature, concentration, temperature, photosensitizer and copolymer composition, on the rate of photocrosslinking of the photoreactive copolymers was investigated for effective industrial application of these polymers as negative photoresists. Copyright © 2004 Society of Chemical Industry     

Synthesis of a photo‐patternable cross‐linked epoxy system containing photodegradable carbonate units for deep UV lithography

Bis(2‐(oxiran‐2‐ylmethyl)‐1,3‐dioxoisoindolin‐5‐yl) carbonate and polymers containing 9‐anthracenylmethylmethacrylate (AMMA), p‐tert‐butoxy styrene (PTBS), and methacrylic acid (MAA) monomeric units were synthesized with the aim of developing a novel photo‐patternable cross‐linked epoxy system. The oxirane groups in bis(2‐(oxiran‐2‐ylmethyl)‐1,3‐dioxoisoindolin‐5‐yl) carbonate were reacted with the carboxylic acid in the polymer to generate a cross‐linked epoxy film, and the photo degradation of the cross‐linked film was achieved through decomposition of the carbonate groups in the cross‐linked film by deep UV irradiation. Because the copolymer containing anthracene groups has relatively high reflective index and absorption at 248 nm, this cross‐linked system can be applied to patternable bottom antireflective coating materials for deep UV lithography applications. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and characterization of novel urethane‐siloxane copolymers with a high content of PCL‐PDMS‐PCL segments

Novel polyurethane copolymers derived from 4,4′‐methylenediphenyl diisocyanate (MDI), 1,4‐butanediol (BD) and α,ω‐dihydroxy‐[poly(caprolactone)‐poly (dimethylsiloxane)‐poly(caprolactone)] (α,ω‐dihydroxy‐(PCL‐PDMS‐PCL); = 6100 g mol^?1) were synthesized by a two‐step polyaddition reaction in solution. In the synthesis of the polyurethanes, the PCL blocks served as a compatibilizer between the nonpolar PDMS blocks and the polar comonomers, MDI and BD. The synthesis of thermoplastic polyurethanes (TPU) with high soft segment contents was optimized in terms of the concentrations of the reactants, the molar ratio of the NCO/OH groups, and the time and temperature of the polyaddition reaction. The structure, composition, and hard MDI/BD segment length of the synthesized polyurethane copolymers were determined by ¹H, ¹³C‐NMR, and two‐dimensional correlation (COSY, HSQC, and HMBC) spectroscopy, while the hydrogen bonding interactions in the copolymers were analyzed by FT‐IR spectroscopy. The influence of the reaction conditions on the structure, molecular weight, thermal, and some physical properties was studied at constant composition of the reaction mixture. A change in the molar ratio of the NCO/OH groups and the reaction conditions modified not only the molecular weight of the synthesized polyurethanes, but also the microstructure and therefore the thermal and physical properties of the copolymers. It was demonstrated that only PCL segments with high soft segment contents crystallize, thereby showing spherulitic morphology. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and characterization of novel thermo‐ and pH‐responsive copolymers based on amphiphilic polyaspartamides

Novel amphiphilic, thermo‐ and pH‐responsive polyaspartamides showing both double‐responsive (pH and temperature) behavior and a sol‐gel transition were prepared and characterized. The polyaspartamide derivatives were synthesized by the successive aminolysis reactions of polysuccinimide using both hydrophobic N‐alkylamine (laurylamine, octylamine, hexylamine) and hydrophilic N‐isopropylethylenediamine. The composition of each component was analyzed by ¹H NMR. At the intermediate composition range, the system showed a lower critical solution temperature behavior in water. The transition temperature (pH dependent) could be modulated by changing the alkyl chain length and graft composition. The temperature dependence of the nanoparticle size distribution of the polyaspartamide derivatives was also examined. The critical micelle concentration of the copolymers in a phosphate‐buffered saline (pH 7.4) solution ranged from 6 to 20 μg/L. In addition, physical gelation, i.e., a sol‐gel transition, was observed in a concentrated solution. These novel double‐responsive and injectable hydrogels have potential biomedical applications such as drug delivery systems and tissue engineering. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and physical properties of liquid‐crystalline copolymers with azobenzene segments

To investigate the effects of photoisomerizable azobenzene segments on the liquid‐crystalline characteristics and thermal properties of polymers, a series of liquid‐crystalline homopolymers and copolymers with azobenzene segments was synthesized. The azobenzene contents of the copolymers were estimated with elemental analysis. The photoisomerization of the azobenzene derivatives was studied with ultraviolet–visible (UV–vis) spectroscopy. The UV–vis absorption of the copolymers was found to be parallel with the content of the azobenzene segments. UV irradiation was found to cause a decrease in the copolymer transmittance around 355 nm due to the photoinduced isomerization from entgegen (E) to zusammen (Z). The phase‐transition temperatures and molecular weights of the polymers were investigated with differential scanning calorimetry and gel permeation chromatography, respectively. The variation in the phase‐transition temperature of the homopolymers before and after UV (365 nm) irradiation was investigated. The bended Z structure was found to disturb the order of the orientation of liquid crystals and to lower the phase‐transition temperature. The appearance of the polymer film was changed from opaque to clear after sufficient UV irradiation. The image recording of the polymer films was achieved after UV irradiation through a mask with pictures. The stability and reliability of the Nematic‐Isotropic phase transition of the homopolymers was evaluated with repeated cycles of 365‐nm UV irradiation and heating at 130°C. After the recycle phase transition was repeated nine times, no significant decay in the response and transmittance could be found. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 2006     

Nanometer‐thick patterned conductive films prepared through the self‐synthesis of polythiophene derivatives

The development of flexible electronics requires the patterning of conductive and active semiconductor films. Although inorganic materials such as indium tin oxide and metal nanoparticles have high conductivity and transparency, their poor interfacial adhesion with organic layers, lack of flexibility, high weight and high capital costs are drawbacks. In contrast, organic conducting polymers have great potential for use in commercial flexible electronic applications because of their low production costs, environmental stability and acceptable conductivities. A UV‐curable photoresist containing hydroxyl groups was prepared from a mixture of a photoinitiator, epoxy‐acrylate resin, hydroxyethyl methacrylate and tripropylene glycol diacrylate. Patterns having line widths/spaces of 100/100 µm and 10/5 µm were fabricated on a poly(ethylene terephthalate) (PET) substrate using lithography techniques. (3‐Methyl‐3,4‐dihydro‐2H‐thieno[3,4‐b]dioxepin‐3‐yl)methanol (ProDOT‐OH) was self‐synthesized through urethane linkages onto the surface of the patterned photoresist on the PET film, which was then dipped into a solution of another monomer, 3‐thienylethoxybutanesulfonate (TEBS), and initiator and polymerized in situ to form conductive poly(ProDOT‐OH‐co‐TEBS) films covering the surface of the patterned resist. The optimal conductivity of the poly(ProDOT‐OH‐co‐TEBS) films was ca 90 S cm^?1 with an optical transparency of ca 70%. A new bottom‐up technique has been developed for the preparation of patterned organic transparent conductive films: self‐synthesis of the monomer using urethane‐forming reactions and subsequent in situ polymerization. The conductivity of the films can be controlled by the polymerization reaction time and the resolution of the pattern. These conductive patterned films might be applicable to the manufacture of industrial touch panels or chemical/biological sensors. Copyright © 2009 Society of Chemical Industry     

Synthesis and characterization of four‐arm star‐shaped polymers and copolymers

Four‐arm star‐shaped polymers and copolymers were obtained by transition metal‐catalyzed atom‐transfer radical polymerization (ATRP). The polymers were characterized by FTIR and ¹H‐NMR spectroscopy. Gel permeation chromatography results indicated the formation of polystyrene and polystyrene‐block‐poly(methyl methacrylate) (PS‐b‐PMMA) arms with controlled molecular weights. In dilute solution, the linear polymers had higher inherent viscosities than star‐shaped ones. Thermogravimetric analysis showed a similar degradation mechanism for linear and star‐shaped polymers. Differential scanning calorimetry indicated the successful formation of diblock star‐shaped copolymers. Copyright © 2006 Society of Chemical Industry     

Synthesis and characterization of a positive‐working,aqueous‐base‐developable photosensitive polyimide precursor

A positive‐working, aqueous‐base‐developable photosensitive polyimide precursor based on poly(amic ester)‐bearing phenolic hydroxyl groups and a diazonaphthoquinone photosensitive compound was developed. The poly(amic ester) was prepared from a direct polymerization of 2,2′‐bis‐(3‐amino‐4‐hydroxyphenyl)hexafluoropropane and bis(n‐butyl)ester of pyromellitic acid in the presence of phenylphosphonic dichloride as an activator. Subsequently, the thermal imidization of the poly(amic ester) precursor at 300°C produced the corresponding polyimide. The inherent viscosity of the precursor polymer was 0.23 dL/g. The cyclized polyimide showed a glass‐transition temperature at 356°C and a 5% weight loss at 474°C in nitrogen. The structures of the precursor polymer and the fully cyclized polymer were characterized by Fourier transform infrared spectroscopy and ¹H‐NMR. The photosensitive polyimide precursor containing 25 wt % diazonaphthoquinone photoactive compound showed a sensitivity of 150 mJ/cm² and a contrast of 1.65 in a 3 μm film with 1.25 wt % tetramethylammonium hydroxide developer. A pattern with a resolution of 10 μm was obtained from this composition. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 352–358, 2002     

Synthesis and characterization of gelatin‐polydimethylsiloxane graft copolymers

Gelatin‐polydimethylsiloxane (PDMS) graft copolymers were prepared through the reaction between gelatin and α‐[3‐(2,3‐epoxypropoxy)propyl]‐ω‐butyl‐PDMSs. The copolymers were characterized by FTIR and ¹H‐NMR spectra. As proved by wide angle X‐ray analysis, a new characteristic crystalline peak appeared after the bonding of PDMS to gelatin chains. The microstructure and the elemental identification of gelatin and copolymers were followed through scanning electron microscope with energy dispersive spectrometer. The glass transition temperature of gelatin and copolymers were obtained by differential scanning calorimetry analysis. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and electrical properties of copolymers of o‐phenylenediamine with aniline, 3,4‐ethylenedioxythiophene and 2,3,5,6‐tetrafluoroaniline

Copolymers (P(PDA/Ar)) of o‐phenylenediamine with aniline (Ar = ANi), 3,4‐ethylenedioxythiophene (Ar = EDOT) and 2,3,5,6‐tetrafluoroaniline (Ar = TFANi) were synthesized via polycondensation initiated by ammonium persulfate. The NH₂ group content in the copolymers was determined by analyzing the ¹H NMR spectra of the N‐acetylated copolymers. Copolymers crosslinked by viologen (1,1'‐disubstituted 4,4'‐bipyridinium dichloride) were obtained by reaction involving the reactive NH₂ groups in the copolymers. The absorption wavelengths of solutions of the copolymers and the electrochemical oxidation and reduction potentials of cast films of the copolymers were affected by the electrical properties of the Ar unit. © 2016 Society of Chemical Industry     

Synthesis and characterization of new biodegradable comb‐dendritic triblock copolymers

A series of well‐defined dumbbell‐shaped triblock copolymers consisting of linear poly(ethylene glycol) (PEG) and comb‐like poly(ε‐caprolactone) (PCL) with varied PCL arm lengths have been synthesized via the sequential preparation of different generation terminal dendronized PEG and ring‐opening polymerization of ε‐caprolactone. The copolymers were characterized using Fourier transform infrared, ¹H NMR and ¹³C NMR spectroscopy and gel permeation chromatography. Differential scanning calorimetry was performed to measure the glass transition temperature, melting point and degree of crystallinity and the PEG segment and PCL segment crystallization temperatures. The crystallization of the copolymers was also studied using X‐ray diffraction. The dumbbell‐shaped copolymers were further used to construct microspheres using a double emulsion method. Scanning electron microscopy and dynamic light scattering results showed the size of the microspheres was about 2 to 4 µm and the size distribution was quite narrow. Copyright © 2012 Society of Chemical Industry     

Effect of polymerization conditions on o‐phenylenediamine and o‐phenetidine oxidative copolymers

A series of new o‐phenylenediamine (OPD)/o‐phenetidine (PHT) copolymers with partly phenazine‐like structures has been successfully synthesized at three polymerization temperatures by chemically oxidative polymerization in four different polymerization media. The molecular structures and properties of the resulting OPD/PHT polymers were investigated by IR, UV–vis and high‐resolution ¹H NMR spectroscopies, and DSC, in order to ascertain the effect of reaction temperature, comonomer ratio and acid medium. The copolymerization mechanism of OPD with PHT monomers has been proposed. It is found that the statistical OPD/PHT copolymer obtained at a temperature of 118 °C has a higher degree of polymerization than that obtained at 12–17 °C. The OPD content in the copolymers calculated from NMR spectroscopic analysis is higher than that in the feed OPD content, whereas the OPD content calculated from element analysis is slightly lower than the feed OPD content. It can be predicted that denitrogenation takes place in the OPD units during the polymerization process at OPD/PHT molar ratios of 90/10 and 100/0. These OPD/PHT copolymers exhibit a much better solubility than the OPD homopolymer, hence suggesting an incorporation of PHT units into the phenazine structure of the homopolymer. The thermal behavior of the copolymers was also studied. Copyright © 2004 Society of Chemical Industry     

Content of trans,trans‐2,4‐decadienal in deep‐fried and pan‐fried potatoes

Trans,trans‐2,4‐decadienal is a by‐product of frying oil that is also transferred to fried food. This aldehyde has been found and quantified both in frying oils and fumes generated during frying. Furthermore, it has been reported that 2,4‐decadienal has cytotoxic and genotoxic effects and promotes LDL oxidation. In the present work trans,trans‐2,4‐decadienal was detected directly in fried potatoes (french‐fries). Moreover, the influence of frying conditions (deep‐frying, pan‐frying), the oil type (olive oil, sunflower oil, cottonseed oil, palm oil and a vegetable shortening) and the degree of thermal deterioration (eight successive frying sessions without replenishment) on the production of 2,4‐decadienal in oil and potatoes was studied. The isolation of the aldehyde was performed by methanol extraction, while the identification and quantification was performed by RP‐HPLC. The quantity of trans,trans‐2,4‐decadienal produced during successive pan‐frying demonstrated a peak at the third and fourth frying session. The highest concentration of trans,trans‐2,4‐decadienal was detected in potatoes fried in sunflower oil, and the lowest in olive oil. The quantity of trans,trans‐2,4‐decadienal in fried potatoes decreased during successive deep‐frying at the seventh frying session or remained stable, except for cottonseed oil. The quantity of trans,trans‐2,4‐decadienal in fried potatoes was considered to be dependent on the oil used, on the frying process and, to a lesser extent, on the oil deterioration. In all cases tested, the highest concentration of trans,trans‐2,4‐decadienal was detected during deep‐frying. The unsaturation degree of the frying oil was considered to promote the formation of trans,trans‐2,4‐decadienal. Considering the quantity of 2,4‐decadienal found in french‐fries and in the respective frying medium, direct quantification of 2,4‐decadienal is required in order to make an estimation of intake from french‐fries.     

Synthesis and characterization of thermo‐ and pH‐sensitive block copolymers bearing a biotin group at the poly(ethylene oxide) chain end

A poly(ethylene oxide)‐block‐poly(dimethylamino ethyl methacrylate) block copolymer (PEO‐b‐PDMAEMA) bearing an amino moiety at the PEO chain end was synthesized by a one‐pot sequential oxyanionic polymerization of ethylene oxide (EO) and dimethylamino ethyl methacrylate (DMAEMA), followed by a coupling reaction between its PEO amino and a biotin derivative. The polymers were charac terized with ¹H NMR spectroscopy and gel permeation chromatography. Activated biotin, biotin‐NHS (N‐hydroxysuccinimide), was used to synthesize biotin‐PEO‐PDMAEMA. In aqueous media, the solubility of the copolymer was temperature‐ and pH‐sensitive. The particle size of the micelle formed from functionalized block copolymers was determined by dynamic light scattering. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3552–3558, 2006     

Synthesis and characterization of novel graft copolymers by radiation‐induced grafting

The radiation‐induced graft copolymerization of N‐vinyl‐2‐pyrrolidone (NVP), 4‐vinyl pyridine (4VP), and 2‐vinyl pyridine (2VP) monomers onto poly (ethylene‐alt‐tetrafluoroethylene) (ETFE) was investigated. The influence of synthesis conditions particularly the solvent was studied. Various solvents, such as n‐propanol, isoproponol, benzyl alcohol, methanol, ethanol, cyclohexanone, tetrahydrofuran (THF), nitromethane, 1,4‐dioxane, and n‐heptane were examined for this purpose. Graft copolymers were characterized by Fourier transform infrared (FTIR) spectroscopy, dynamic mechanical analysis (DMA), and scanning electron microscopy‐energy dispersive spectroscopy (SEM‐EDAX). It was found that the nature of the solvent had profound influence over the grafting reaction. Cyclohexanone, n‐propanol, and isoproponol for 4VP/ETFE grafting, THF and 1,4‐dioxane for NVP/ETFE grafting, and benzyl alcohol and methanol for 2VP/ETFE grafting were found to be the suitable solvents yielding highest graft levels. Isoproponol and n‐propanol are promising in terms of both graft level and mechanical properties for 4VP/ETFE. Grafting of NVP, 4VP, and 2VP onto ETFE were verified through FTIR spectroscopy. Storage modulus and glass transition temperature of the copolymers were found to increase as graft level increased. Surface profile of representative films was also investigated by viewing the distribution of elemental nitrogen using SEM‐EDAX. Results indicated that copolymers of 4VP, NVP, and 2VP are considerably different from each other. 4VP‐based copolymers exhibited relatively more homogenous grafting over the surface compared with NVP‐ and 2VP‐based copolymers. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and characterization of hydroxypropyl terminated polydimethylsiloxane‐polyurethane copolymers

Polyurethane (PU) block copolymers were synthesized using prepared hydroxypropyl terminated polydimethylsiloxane (HTPDMS MW 990) and polyether diols (N‐210) as soft segment with 4,4′‐diphenylmethane diisocyanate (MDI) and 1,4‐butanediol. This low molecular weight polydimethylsiloxanes (PDMS) containing hydroxypropyl end‐groups displayed better compatibility with PU than common PDMS. In this article, we illustrate its synthesis routes and confirmed the proposed molecular structures using NMR and infrared radiation (IR). We varied the contents of HTPDMS and N‐210 in soft segments (HTPDMS—N‐210: 0 : 100, 20 : 80, 40 : 60, 60 : 40, 80 : 20, and 100 : 0) to synthesize a series of PDMS‐PU copolymer. IR spectroscopy showed the assignment characteristic groups of each peak in copolymers and confirmed that the desired HTPDMS‐PU copolymers have been prepared. The different thermal, dynamic mechanical and surface properties of the copolymers were compared by thermogravimetry, DMA, contact angle and solvent resistance. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Effect of LED optical characteristics on temporal behavior of o‐cresol decomposition by UV/TiO2 process

BACKGROUND: An ultraviolet light‐emitting diode (UV‐LED) was used in this investigation as the light source for the photocatalytic decomposition of o‐cresol in aqueous solution because of its efficiency, design flexibility, and durability. The UV light intensities of the corn‐shaped LED tube designed in this investigation were relatively uniform due to the correct arrangement of LEDs. RESULTS: For experiments conducted with initial o‐cresol concentrations of 9 mg L^?1 and pH 3, more than 80% of o‐cresols were decomposed after 8 h of irradiation. The calculated photonic efficiency (about 1·06%) for experiments conducted with continuous illumination was much lower than those (1·69–6·27%) obtained with periodic illumination. CONCLUSION: The proposed Langmuir–Hinshelwood kinetic model with modification of UV light intensity attenuation could be adequately applied to describe the temporal behavior of the o‐cresol decomposition in aqueous solution by the UV‐LED/TiO₂ process. Copyright © 2007 Society of Chemical Industry