Observations of physical aging in a polycarbonate and acrylonitrile–butadiene–styrene blend

The effects of physical aging of a 75 : 25 PC/ABS blend have been studied using differential scanning calorimetry (DSC) and Fourier transform infrared spectroscopy (FTIR). From DSC, two distinct peak endotherms at about 90°C and 110°C, which are associated with the glass transition of ABS (T_g,ABS) and PC (T_g,PC) components, respectively, were observed. When progressive aging was monitored at 80°C for over 1000 h, the changes in enthalpic relaxation, glass and fictive temperatures for the blend followed similar trends to those already seen in the literature for PC aged between 125 and 130°C. The rate of enthalpy relaxation was also comparable. The plot of peak endotherm against logarithmic aging time for the PC blend constituent, however, behaved quite differently from the linear relationship known for highly aged PC. The ABS peak component also appeared to be insensitive to aging. Both observations were confirmed to be statistically significant using analysis of variance methods. Using temperature modulated‐DSC, there is evidence that aging increases the blend miscibility as the T_g,PC shifts toward the stationary T_g,ABS during aging. Parallel FTIR investigations found oxidation of butadiene during aging to be even at this relatively low temperature, forming hydroxyl and carbonyl degradation products. The presence of ABS in the blend also appeared to have prevented the shifting from the trans‐cis to trans‐trans arrangement of the carbonate linkage, which is a well‐known phenomenon during elevated temperature aging of PC alone. Moreover, the carbonate linkage appears to have been at the lower energy, trans‐trans, arrangement prior to the aging process. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Recycling of blends of acrylonitrile–butadiene–styrene (ABS) and polyamide

The aim of this work is to evaluate routes to upgrade recycled engineering plastics, especially mixed plastics with acrylonitrile–butadiene–styrene copolymers (ABS) as the major component. A core‐shell impact modifier was successfully used to improve the impact strength of blends of ABS and ABS/polycarbonate (PC) blends recycled from the automotive industry. However, the presence of other immiscible components like polyamide (PA), even in small amounts, can lead to a deterioration in the overall properties of the blends. A styrene–maleic anhydride (SMA) copolymer and other commercial polymer blends were used to promote the compatibilization of ABS and PA. The core‐shell impact modifier was again found to be an efficient additive with regard to the impact strength of the compatibilized ABS/PA blends. The results obtained with fresh material blends were quite promising. However, in blends of recycled ABS and glass‐fiber‐reinforced PA, the impact strength did not exhibit the desired behavior. The presence of poorly bonded glass fibers in the blend matrix was the probable reason for the poor impact strength compared with that of a blend of recycled ABS and mineral‐filled PA. Although functionalized triblock rubbers (SEBS–MA) can substantially enhance the impact strength of PA, they did not improve the impact strength of ABS/PA blends because the miscibility with ABS is poor. The possibilities of using commercial polymer blends to compatibilize otherwise incompatible polymer mixtures were also explored giving promising results. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2535–2543, 2002     

Boiling water aging of polycarbonate and polycarbonate/acrylonitrile–butadiene–styrene resin and polycarbonate/low‐density polyester blends

The effects of boiling water on the mechanical and thermal properties and morphologies of polycarbonate (PC), PC/acrylonitrile–butadiene–styrene resin (PC/ABS), and PC/low‐density polyester (PC/LDPE) blends (compositions of PC/ABS and PC/LDPE blends were 80/20) were studied. PC and the PC/ABS blend had a transition from ductile to brittle materials after boiling water aging. The PC/LDPE blend was more resistant to boiling water aging than PC and the PC/ABS blend. The thermal properties of glass‐transition temperature (T_g) and melting temperature (T_m) in PC and the blends were measured by DSC. The T_g of PC and PC in the PC/ABS and PC/LDPE blends decreased after aging. The T_g of the ABS component in the PC/ABS blend did not change after aging. The supersaturated water in PC clustered around impurities or air bubbles leading to the formation of microcracks, which was the primary reason for the ductile–brittle transition in PC, and the microcracks could not recover after PC was treated at 160°C for 6 h. The PC/ABS blend showed slightly higher resistance to boiling water than did PC. The highest resistance to boiling water of the PC/LDPE blend may be attributed to its special structural morphology. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 589–595, 2003     

Gloss reduction and morphological properties of polycarbonate and poly(methyl methacrylate‐acrylonitrile‐butadiene‐styrene) blends with SAN‐co‐GMA as a reactive compatibilizer

The gloss properties of the polycarbonate (PC)/poly(methyl methacrylate‐acrylonitrile‐butadiene‐styrene) (MABS) blend with styrene‐acrylonitrile‐co‐glycidyl methacrylate (SAN‐co‐GMA) as a compatibilizing agent were investigated. For the PC/poly(MABS)/SAN‐co‐GMA (65/15/20, wt %) blend surface, the reduction of gloss level was observed most significantly when the GMA content was 0.1 wt %, compared with the blends with 0.05 wt % GMA or without GMA content. The gloss level of the PC/poly(MABS)/SAN‐co‐GMA (0.1 wt % GMA) blend surface was observed to be 35, which showed 65% lower than the PC/poly(MABS)/SAN‐co‐GMA blend without GMA content. The gloss reduction was most probably caused by the insoluble fractions of the PC/poly(MABS)/SAN‐co‐GMA blend that were formed by the reaction between the carboxylic acid group in poly(MABS) and epoxy group in SAN‐co‐GMA. The results of optical and transmission electron microscope analysis, spectroscopy study, and rheological properties supported the formation of insoluble structure of the PC/poly(MABS)/SAN‐co‐GMA blend when the GMA content was 0.1 wt %. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46450.     

Influences of the phenolic curative content and blend proportions on the properties of dynamically vulcanized natural rubber/acrylonitrile–butadiene–styrene blends

The vulcanization of natural rubber (NR)‐blended acrylonitrile–butadiene–styrene (ABS) was carried out with a phenolic curing agent by a melt‐mixing process. The NR compound was first prepared before blending with ABS. The effects of the phenolic curative contents (10, 15, and 20 phr) and blend proportions (NR/ABS ratio = 50 : 50, 60 : 40, and 70 : 30) on the mechanical, dynamic, thermal, and morphological properties of the vulcanized NR/ABS blends were investigated. The tensile strength and hardness of the blends increased with increasing ABS content, whereas the elongation at break decreased. The strength property resulting from the thermoplastic component and the vulcanized NR was an essential component for improving the elasticity of the blends. These blends showed a greater elastic response than the neat ABS. The thermal stability of the blends increased with increasing ABS component. Scanning electron micrographs of the blends showed a two‐phase morphology system. The vulcanized 60 : 40 NR/ABS blend with 15‐phr phenolic resin showed a uniform styrene‐co‐acrylonitrile phase dispersed in the vulcanized NR phase; it provided better dispersion between the NR and ABS phases, and this resulted in superior elastic properties. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42520.     

Influence of epoxy resin on the properties of maleic anhydride functionalized acrylonitrile–butadiene–styrene copolymer toughened polyamide 6 blends

Maleic anhydride functionalized acrylonitrile–butadiene–styrene copolymer (ABS‐g‐MA) was used as an impact modifier of polyamide 6 (PA6). Epoxy resin was introduced into PA6/ABS‐g‐MA blends to further improve their properties. Notched Izod impact tests showed that the impact strength of PA6/ABS‐g‐MA could be improved from 253 to 800 J/m with the addition of epoxy resin when the ABS‐g‐MA content was set at 25 wt %. Differential scanning calorimetry results showed that the addition of epoxy resin made the crystallization temperature and melting temperature shift to lower temperatures; this indicated the decrease in the PA6 crystallization ability. Dynamic mechanical analysis testing showed that the addition of epoxy resin induced the glass‐transition temperature of PA6 and the styrene‐co‐acrylonitrile copolymer phase to shift to higher temperatures due to the chemical reactions between PA6, ABS‐g‐MA, and epoxy resin. The scanning electron microscopy results indicated that the ABS‐g‐MA copolymer dispersed into the PA6 matrix uniformly and that the phase morphology of the PA6/ABS‐g‐MA blends did not change with the addition of the epoxy resin. Transmission electron microscopy showed that the epoxy resin did not change the deformation mechanisms of the PA6/ABS‐g‐MA blends. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Thermal aging of bisphenol-A polycarbonate/acrylonitrile–butadiene–styrene blends

Thermal aging of immiscible bisphenol-A polycarbonate/acrylonitrile–butadiene–styrene (PC/ABS) blends containing 25, 60, and 75% PC and the PC and ABS blend components have been studied. Changes in Izod impact properties and dynamic mechanical spectra are reported following aging at 90, 110, and 130°C for times up to 1500 h. PC/ABS blends containing 60 and 75% PC were found to retain high impact performance following aging at elevated temperatures, compared to the PC blend component. Dynamic mechanical spectroscopy is an effective probe for investigating the structure–property changes occurring and the mechanisms of aging. For PC and ABS, the changes were mainly due to physical aging of the amorphous polymers when aged below the glass-transition temperature. For the PC/ABS blends, oxidative degradation additionally contributes to loss of toughness. Although structure–property changes are related to the behavior of the blend components, additional factors of potential importance for multiphase polymer–polymer systems have been identified, including a redistribution of stabilizers during the blend manufacture. © 1995 John Wiley & Sons, Inc.     

Online monitoring of the influence of the chemical structure of hindered amines on the hydrolysis of polycarbonate in a polycarbonate/poly(acrylonitrile–butadiene–styrene) blend by ultraviolet–visible spectroscopy

Without stabilization, polycarbonate (PC)/poly(acrylonitrile–butadiene–styrene) (ABS) blends are susceptible to a loss of mechanical properties after a few days of exposure to weathering conditions. ABS can be stabilized against terrestrial light by the use of hindered amines in combination with a UV absorber; such hindered amines cannot be used when PC is present in the polymer blend. The hydrolysis of PC is accelerated when a small amount of a hindered amine light stabilizer (HALS) is incorporated into the resin and is exposed to elevated temperatures. In this study, three different HALSs (Tinuvin 123, Tinuvin 770, and Tinuvin 765, Ciba, Basel, Switzerland) were used as UV stabilizers for PC/ABS blends, and their effects on the PC phase were observed with online ultraviolet–visible spectroscopy on extruded flat films. These stabilizers were compounded with the blends in a corotating twin‐screw extruder at 240°C. The molecular weight of the compounded samples was determined by gel permeation chromatography. The extent of degradation induced by the HALSs on the PC phase was found to be a function of its chemical structure. Tinuvin 123 with an amino ether functional group enhanced degradation in comparison with Tinuvin 770 and Tinuvin 765. Tinuvin 770, a secondary amine, was apt to be more reactive than Tinuvin 765, a tertiary amine, because less steric hindrance was experienced by the former. Accelerated aging of the compounded samples was performed. Decreased degradation was observed for the samples containing hindered amines; however, the HALSs alone were not effective in protecting the PC/ABS blends against harmful UV light. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Polylactide toughening with epoxy‐functionalized grafted acrylonitrile–butadiene–styrene particles

Glycidyl methacrylate functionalized acrylonitrile–butadiene–styrene (ABS‐g‐GMA) particles were prepared and used to toughen polylactide (PLA). The characteristic absorption at 1728 cm^?1 of the Fourier transform infrared spectra indicated that glycidyl methacrylate (GMA) was grafted onto the polybutadiene phase of acrylonitrile–butadiene–styrene (ABS). Chemical reactions analysis indicated that compatibilization and crosslinking reactions took place simultaneously between the epoxy groups of ABS‐g‐GMA and the end carboxyl or hydroxyl groups of PLA and that the increase of GMA content improved the reaction degree. Scanning electron microscopy results showed that 1 wt % GMA was sufficient to satisfy the compatibilization and that ABS‐g‐GMA particles with 1 wt % GMA dispersed in PLA uniformly. A further increase of GMA content induced the agglomeration of ABS‐g‐GMA particles because of crosslinking reactions. Dynamic mechanical analysis testing showed that the miscibility between PLA and ABS improved with the introduction of GMA onto ABS particles because of compatibilization reactions. The storage modulus decreased for the PLA blends with increasing GMA content. The decrease in the storage modulus was due to the chemical reactions in the PLA/ABS‐g‐GMA blends, which improved the viscosity and decreased the crystallization of PLA. A notched impact strength of 540 J/m was achieved for the PLA/ABS‐g‐GMA blend with 1 wt % GMA, which was 27 times than the impact strength of pure PLA, and a further increase in the GMA content in the ABS‐g‐GMA particles was not beneficial to the toughness improvement. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Impact strength in ABS–PPO blends compatibilized with styrene–acrylonitrile–glycidil methacrylate terpolymers

The impact strength of the acrylonitrile-co-butadiene-co-styrene terpolymer–poly(2,6-dimethyl-1,4-phenylene oxide (ABS–PPO) blends compatibilized with styrene–acrylonitrile modified with glycidil methacrylate (SAN–GMA) terpolymer can be significantly enhanced by the various processing conditions in reaction extrusion. Four different ABS terpolymers are used depending on the composition of acrylonitrile, styrene, and butadiene. The morphology of polybutadiene latex in ABS-1, ABS-3, and ABS-4 is an agglomerated type, while that of ABS-2 is a bimodal one. The three different methods in in situ compatibilizing extrusion are employed; the simple mixing of ABS and PPO, the simultaneous mixing of ABS and PPO, the reactive compatibilizer SAN–GMA, maleic anhydride (MA; designated A-series), and then the stepwise mixing of the mixtures of ABS–SAN–GMA in the MA-modified PPO (designated B-series). Although the ABS-4–PPO blend depicted the highest impact strength in the simple mixing, the ABS-3B–PPO blend showed the best impact strength in the stepwise mixing. The former behavior may be arisen from the high content of BR, whereas the latter may be due to the agglomerated rubber phase with SAN–GMA. The highest impact strength (47 kg·cm·cm⁻¹) was observed in ABS-3B–PPO at 50/50 with an inclusion of 10 wt % GMA (2) and 1 wt % MA. Thus, the proposed reaction mechanism is an existence of the compatibility between ABS and SAN–GMA and the reactivity between the MA-modified PPO and SAN–GMA. Phase morphology of the ABS-2–PPO and ABS-3–PPO blends were compared, and more efficient dispersion of ABS was observed in the B-series than in the A-series. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 841–852, 1999     

Recycling of acrylonitrile–butadiene–styrene and high‐impact polystyrene from waste computer equipment

Acrylonitrile–butadiene–styrene (ABS) and high‐impact polystyrene (HIPS) are two of the plastics most frequently used as outer casings for computer equipment such as monitors, keyboards, and other similar components. We assessed the effects of the recycling and blending of ABS and HIPS on mechanical properties. We found that the effects of recycling on ABS and HIPS were similar, in that changes in glass‐transition temperatures, tensile strengths, and tensile moduli were negligible, but strains to failure and impact strengths were reduced considerably. Blending proportions of ABS and HIPS caused no more deterioration in properties than occurred as a result of the recycling process, and the presence of small proportions of one material in the other actually restored significant amounts of ductility, as seen by increases in the strains to failure. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 572–578, 2002     

Compatibility and thermal properties of poly(acrylonitrile–butadiene–styrene) copolymer blends with poly(methyl methacrylate) and poly(styrene‐co‐acrylonitrile)

The mechanical and heat‐resistant properties of acrylonitrile–butadiene–styrene (ABS) binary and ternary blends were investigated. The relationship of compatibility and properties was discussed. The results show that poly(methyl methacrylate) (PMMA) and styrene–maleic anhydride (SMA) can improve the thermal properties of conventional ABS. The Izod impact property of ABS/PMMA blends increases significantly with the addition of PMMA, whereas that of ABS/SMA blends decreases significantly with the addition of SMA. Blends mixed with high‐viscosity PMMA are characterized by higher heat‐distortion temperature (HDT), and their heat resistance is similar to that of blends mixed with SMA. For high‐viscosity PMMA, from 10 to 20%, it is clear that blends appear at the brittle–ductile transition, which is related to the compatibility of the two phases. TEM micrographs show low‐content and high‐viscosity PMMA in large, abnormally shaped forms in the matrix. Compatibility between PMMA and ABS is dependent on both the amount and the viscosity of PMMA. When the amount of high‐viscosity PMMA varied from 10 to 20 wt %, the morphology of the ABS binary blends varied from poor to satisfactory compatibility. As the viscosity of PMMA decreases, the critical amount of PMMA needed for the compatibility of the two phases also decreases. SMA, as a compatibilizer, improved the interfacial adhesiveness of ABS and PMMA, which results in PMMA having good dispersion in the matrix. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2652–2660, 2002     

Poly(acrylonitrile‐butadiene‐styrene)/Poly(ether ether ketone) Blends: an Attempt Towards a Polymer Reinforced Polymer Composite

Summary: Blends of poly(acrylonitrile‐butadiene‐styrene) (ABS) and poly(ether ether ketone) (PEEK), in which PEEK has been used as a reinforcing medium for the ABS matrix in ratios up to 20 wt.‐% of the blend, were prepared by melt mixing using a laboratory mixer. All the blend compositions were processed at the ABS processing temperature so that the PEEK was dispersed in the ABS matrix without actually melting. Differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) studies revealed that the glass transition temperature (T_g) of the ABS phase in the blend did not show any appreciable change with composition. The dynamic storage modulus measured by DMA was found to be higher for the blend as compared to pure ABS due to reinforcement of the matrix by PEEK. The tensile strength and modulus behavior of these blends were found to follow the curves predicted using models proposed for composite systems having perfect adhesion, which shows the presence of some physical interaction between the blend components. The good tensile properties of the blend have been correlated with the observed morphology. The disperse phase in the blend has been found to be present in extremely small (sub‐micron) dimensions, which not only provides more surface area for possible interactions between the blend components but also result in efficient stress transfer between the matrix and the dispersed phase during the tensile tests. The thermal stability of the blends was investigated using thermogravimetric analysis (TGA). TGA further revealed that the constituents degraded at their respective decomposition temperatures.

SEM micrograph of tensile fractured surface of an ABS/PEEK 90/10 blend.     

Augmenting the performance of acrylonitrile–butadiene–styrene plastics for low‐noise dynamic applications

The main objective of this study was to enhance the performance of acrylonitrile–butadiene–styrene (ABS) plastics for dynamic structural applications, including those of automobile relevance. First, ABS was modified by blending with maleic anhydride grafted styrene–ethylene–butadiene–styrene block copolymer (MA‐g‐SEBS) in various proportions. Squeaking noise characteristics were evaluated by measurement of the frictional behavior in an in‐house fabricated friction testing apparatus, and the results are explained on the basis of the change in surface energy upon modification. Detailed dynamic mechanical analyses (strain, frequency, and temperature sweep) revealed significant improvements in the damping characteristics of the modified ABS, especially that modified with 10 wt % MA‐g‐SEBS, without much sacrifice in its mechanical strength. The modulus values predicted with Kerner's model of the blends were well correlated with the morphological changes upon modification. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Fire‐retardant action of resorcinol bis(diphenyl phosphate) in PC–ABS blend. II. Reactions in the condensed phase

The thermal decomposition of polycarbonate (PC), PC containing resorcinol bis(diphenyl phosphate) (RDP), and PC—acrylonitrile–butadiene–styrene (PC–ABS) blend containing RDP was studied by thermogravimetry. Volatile and solid products of thermal decomposition were collected at different steps of thermal decomposition and characterized either by gas chromatography–mass spectrometry or infrared and chemical analysis. It was found that phosphorus accumulates in the condensed phase. Upon combustion of the fire‐retardant mixture PC–ABS + RDP, accumulation of phosphorus is observed in the charred layer, at the surface of the burning specimens. It is suggested that PC undergoes a Fries‐type rearrangement upon thermal decomposition, and RDP reacts with the formed phenolic groups through a trans‐esterification mechanism. Kinetic analysis of the thermal decomposition of PC containing RDP supports the proposed mechanism. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1863–1872, 1999     

Effects of the polybutadiene/poly(styrene‐co‐acrylonitrile) ratio in a polybutadiene‐g‐poly(styrene‐co‐acrylonitrile) impact modifier on the morphology and mechanical behavior of acrylonitrile–butadiene–styrene blends

Polybutadiene‐g‐poly(styrene‐co‐acrylonitrile) (PB‐g‐SAN) impact modifiers with different polybutadiene (PB)/poly(styrene‐co‐acrylonitrile) (SAN) ratios ranging from 20.5/79.5 to 82.7/17.3 were synthesized by seeded emulsion polymerization. Acrylonitrile–butadiene–styrene (ABS) blends with a constant rubber concentration of 15 wt % were prepared by the blending of these PB‐g‐SAN copolymers and SAN resin. The influence of the PB/SAN ratio in the PB‐g‐SAN impact modifier on the mechanical behavior and phase morphology of ABS blends was investigated. The mechanical tests showed that the impact strength and yield strength of the ABS blends had their maximum values as the PB/SAN ratio in the PB‐g‐SAN copolymer increased. A dynamic mechanical analysis of the ABS blends showed that the glass‐transition temperature of the rubbery phase shifted to a lower temperature, the maximum loss peak height of the rubbery phase increased and then decreased, and the storage modulus of the ABS blends increased with an increase in the PB/SAN ratio in the PB‐g‐SAN impact modifier. The morphological results of the ABS blends showed that the dispersion of rubber particle in the matrix and its internal structure were influenced by the PB/SAN ratio in the PB‐g‐SAN impact modifiers. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2165–2171, 2005     

Blends of recycled polycarbonate and acrylonitrile–butadiene–styrene: comparing the effect of reactive compatibilizers on mechanical and morphological properties

Blends of recycled polycarbonate (PC) and acrylonitrile–butadiene–styrene (ABS) were prepared and some mechanical and morphological properties were investigated. To compatibilize these blends, ABS‐g‐(maleic anhydride) (ABS‐g‐MA) and (ethylene–vinyl acetate)‐g‐(maleic anhydride) (EVA‐g‐MA) with similar degree of grafting of 1.5% were used. To compare the effect of the type of compatibilizer on mechanical properties, blends were prepared using 3, 5 and 10 phr of each compatibilizer. A co‐rotating twin‐screw extruder was used for blending. The results showed that ABS‐g‐MA had no significant effect on the tensile strength of the blends while EVA‐g‐MA decreased the tensile strength, the maximum decrease being about 9.6% when using 10 phr of this compatibilizer. The results of notched Charpy impact strength tests showed that EVA‐g‐MA increased the impact strength of blends more than ABS‐g‐MA. The maximum value of this increase occurred when using 5 phr of each compatibilizer, it being about 54% for ABS‐g‐MA and 165% for EVA‐g‐MA. Scanning electron microscopy micrographs showed that the particle size of the dispersed phase was decreased in the continuous phase of PC by using the compatibilizers. Moreover, a blend without compatibilizer showed brittle behaviour while the blends containing compatibilizer showed ductile behaviour in fracture. © 2013 Society of Chemical Industry     

Effect of the addition of acrylonitrile/ethylene–propylene–diene monomer (EPDM)/styrene graft copolymer on the morphology–properties relationships in poly(styrene‐co‐acrylonitrile)/EPDM rubber blends

Blends of poly(styrene‐co‐acylonitrile) (SAN) with ethylene–propylene–diene monomer (EPDM) rubber were investigated. An improved toughness–stiffness balance of the SAN/EPDM blend was obtained when an appropriate amount of acrylonitrile–EPDM–styrene (AES) graft copolymer was added, prepared by grafting EPDM with styrene–acrylonitrile copolymer, and mixed thoroughly with both of the two components of the blend. Morphological observations indicated a finer dispersion of the EPDM particles in the SAN/EPDM/AES blends, and particle size distribution became narrower with increasing amounts of AES. Meanwhile, it was found that the SAN/EPDM blend having a ratio of 82.5/17.5 by weight was more effective in increasing the impact strength than that of the 90/10 blend. From dynamic mechanic analysis of the blends, the glass‐transition temperature of the EPDM‐rich phase increased from ?53.9 to ?46.2°C, even ?32.0°C, for the ratio of 82.5/17.5 blend of SAN/EPDM, whereas that of the SAN‐rich phase decreased from 109.2 to 108.6 and 107.5°C with the additions of 6 and 10% AES copolymer contents, respectively. It was confirmed that AES graft copolymer is an efficient compatibilizer for SAN/EPDM blend. The compatibilizer plays an important role in connecting two phases and improving the stress transfer in the blends. Certain morphological features such as thin filament connecting and even networking of the dispersed rubber phase may contribute to the overall ductility of the high impact strength of the studied blends. Moreover, its potential to induce a brittle–ductile transition of the glassy SAN matrix is considered to explain the toughening mechanism. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1685–1697, 2004     

Compatibilization of SBR/NBR blends using chemically modified styrene‐co‐butadiene rubber Part 2. Effect of compatibilizer loading

The present work focuses on the compatibization of styrene‐co‐butadiene rubber (SBR)/acrylonitrile‐co‐butadiene rubber (NBR) blends with dichlorocarbene modified styrene‐co‐butadiene rubber (DCSBR) as a function of concentration of compatibilizer and composition of the blend. FTIR studies, differential scanning calorimetry and dynamic mechanical analysis reveal molecular level miscibility in the blends in the presence of compatibilizer. The formation of interfacial bonding is assessed by analysis of swelling behaviour, cure characteristics, stress–strain data and mechanical properties. These studies show that the compatibilizing action of DCSBR becomes more prominent as the proportion of NBR in the blend increases. The resistance of the vulcanizate towards thermal and oil ageing improved with compatibilization. The change in technological properties is correlated with the crosslink density of the blends assessed from swelling and stress–strain data. © 2001 Society of Chemical Industry     

The role of polycarbonate molecular weight in the poly(L‐lactide) blends compatibilized with poly(butylene succinate‐co‐L‐lactate)

Poly(butylene succinate‐co‐L ‐lactate) (PBSL)–compatibilized poly(L ‐lactide) (PLLA) polymer blends with two commercial grades of polycarbonate (PC) were investigated. The capillary tests showed that the steady shear viscosity of high molecular weight PC (PC‐L) was 10 times higher than that of low molecular weight PC (PC‐AD) throughout the shear rate range under investigation. Morphologic examination revealed that the shape of the dispersed PC‐L phase in the as‐extruded blends was largely spherical, but the PC‐AD phase was more like a rod and elongated further during injection molding. Notched Izod impact strength (IS) of the unmodified PLLA/PC‐L blend was higher than that of PC‐AD blend. The IS of modified ternary blends increased with PBSL content because of enhanced phase interaction indicated from thermal and morphologic analysis. The PBSL modification also enhanced IS more significantly in PLLA/PC‐L than in PLLA/PC‐AD blends. On the contrary, the heat deflection temperature (HDT) of PLLA/PC‐L binary system was much lower than that of PLLA/PC‐AD. HDT of PBSL‐modified PLLA/PC‐AD blends dropped with increasing PBSL content, which is a ductile polymer. Thermal and dynamic mechanical analysis of the ternary blends showed that individual components were immiscible with distinct T_gs for PC and PLLA and distinct T_ms for PBSL and PLLA. POLYM. ENG. SCI., 2013. © 2012 Society of Plastics Engineers