Improvement in mechanical,electrical, and shape memory properties of the polystyrene-based carbon fiber-reinforced polymer composites containing carbon nanotubes

Carbon fiber-reinforced polymers based on polystyrene matrix containing elastomer and carbon nanotubes (CNTs) were produced by compression molding. The effects of carbon fabric (CF) concentration and silane treatment on the morphology, mechanical, electrical, and shape memory properties of the multilayer composites were investigated. The SEM analyses showed that fibers of the silane-treated CFs were more homogeneously covered with the polymer layers than the untreated CFs. The tensile strength and modulus of the composites increased by 521% and 125%, respectively, with an increasing number of CF plies from one to five. Upon silane treatment, the tensile strength of the multilayer composite improved by 26%, and the tensile modulus decreased by 18.4%. Electrical conductivities of the composites were in the semiconductor region due to the presence of both CNTs and CFs. 100% shape recovery less than a minute recovery time was obtained for all the composites with electrically triggered bending test.     

Interface improvement of carbon fiber/methylphenylsilicone resin composites by fiber surface coating of polyhedral oligomeric silsesquioxanes

To enhance interfacial properties of carbon fibers (CFs)-reinforced methylphenylsilicone resin (MPSR) composites, we introduced an appropriate interface reinforced by trisilanolphenyl-polyhedral oligomeric silsesquioxanes (trisilanolphenyl-POSS) between CFs and MPSR with a liquid phase deposition strategy. Chemical bonds among silanol groups of trisilanolphenyl-POSS, hydroxyl-functionalized CF (CF–OH), and silanol end groups of MPSR in the coating were expected to be formed through condensation reaction during the prepared process. CFs with and without sizing treatment-reinforced MPSR composites were prepared by a compression molding method. X-ray photoelectron spectroscopy revealed that trisilanolphenyl-POSS particles enhanced the contents of fiber surface oxygen-containing groups and silicon-containing functional groups. Scanning electron microscopy and atomic force microscopy images showed that trisilanolphenyl-POSS nanoparticles have been introduced onto the fiber surface obviously and the surface roughness increased sharply. Dynamic contact angle analysis indicated that trisilanolphenyl-POSS-modified sizing agent could improve the fiber wettability and surface energy significantly. Short-beam bending test and impact toughness test results showed that the interlaminar shear strength and impact resistance of the sized CFs composites were enhanced greatly with increasing amplitudes of more than 35 and 27% in comparison with those of untreated CF composites, respectively. Cryo-fractured surface topographies of composites confirmed that interfacial adhesion between CFs and MPSR has been improved after sizing treatment. Meanwhile, the sizing treatment does not decrease single fiber tensile strength.     

Relationship between electrical resistance and strain of carbon fibers upon loading

The changes in electrical resistance of carbon fibers during a tensile elongation were investigated to understand the electromechanical mechanism in carbon fibers. The fractional electrical resistance of carbon fibers initially increased slightly with increasing elongation, however, increased abruptly beyond a certain strain where the rupture of fibers began to increase. Contribution to this change in electrical resistance was analyzed in terms of dimensional change of fibers, number of ruptured fibers, and degree of fiber contacts. The effect of the number of ruptured fibers was the most dominant, whereas the effect of the dimensional change of carbon fibers due to elongation was relatively small. The degree of contacts between fibers affected the change in electrical resistance dominantly at the large elongation. The residual electrical resistance appeared upon removal of the applied strain and increased with increasing elongation, regardless of the static and dynamic loading. Consequently, the smart characteristics of carbon fibers due to the existence of the residual electrical resistance are primarily ascribed to the number of ruptured fibers and contacts between fibers. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 2082–2087, 2000     

High performance thermoplastic composites: Study on the mechanical,thermal, and electrical resistivity properties of carbon fiber‐reinforced polyetheretherketone and polyethersulphone

High temperature processing thermoplastic polymers, polyetheretherketone (PEEK) and polyethersulphone (PES), were melt blended with carbon fibers (CFs) to make composites. These composites were investigated for their mechanical, thermal, and electrical properties. Mechanical properties that are expressed in terms of storage modulus, loss, and damping were enhanced with the addition of CFs. Thermal properties were determined by DSC and TGA. These methods help to understand the effects of fiber content and fiber–matrix adhesion in the composites. Composites were also tested for their electrical and thermal conductivity because CFs leave the composites thermally and electrically conductive. CFs enhanced the crystallinity of the PEEK appreciably that in turn influenced thermal conductivity, electrical resistivity, and the stiffness of PEEK/CF (composites of PEEK with CFs). PES/CF (composites of PES with CF) shows a different behavior due to the amorphous nature of PES. The work involves one filler and two different matrices, and so it provides an interesting comparison of how matrix morphology can influence the properties of composites. POLYM. COMPOS. 28:785–796, 2007. © 2007 Society of Plastics Engineers.     

Carbon‐fiber‐reinforced acrylonitrile–styrene–acrylate composites: Mechanical and rheological properties and electrical resistivity

The aim of this study was to improve the mechanical properties of an acrylonitrile–styrene–acrylate copolymer (ASA) with the help of carbon fibers (CFs). Additionally, the effects of the CFs on the morphology, rheological properties, dynamical mechanical properties, electrical resistivity, and heat resistance of the ASA composites were studied with scanning electron microscopy, rotational rheometry, and dynamic thermomechanical analysis (DMA). The mechanical properties of the ASA composites were enhanced largely by the CFs. The maximum tensile strength of the ASA/CF composites reached 107.2 MPa. The flexural strength and flexural modulus also reached 162.7 MPa and 12.4 GPa, respectively. These findings were better than those of neat ASA; this was attributed to the excellent interfacial adhesion between the CFs and ASA resin. Rheological experiments proved that the viscosity and storage modulus (G′) values of the ASA/CF composites did not increase until the CF content reached 20%. The DMA outcomes confirmed that the glass‐transition temperature of the ASA composites was elevated from 120.6 to 125°C. Importantly, the G′ values of the composites with 20 and 30% CFs showed a large increase during heating. In addition, the ASA/CF composites exhibited excellent conductivity and heat resistance. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43252.     

Enhanced interfacial strength and mechanical properties of carbon fiber composites by introducing functionalized silica nanoparticles into the interface

Introducing nanoparticles onto the surface of carbon fibers (CFs) is a useful method for enhancing the quality of fiber-matrix interface. In this work, a liquid sizing agent containing functionalized silica nanoparticles (SiO₂) was well prepared to improve interfacial strength and mechanical properties of composites. In order to enhance the dispersion of SiO₂ nanoparticles in sizing agent, SiO₂ nanoparticles were chemically grafted with 3-aminopropyltriethoxysilane (APS), and then silanized silica (SiO₂-APS) was introduced into the interphase by a conventional sizing process as well. Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and thermogravimetric analysis (TGA) confirmed the successful preparation of SiO₂-APS. Scanning electron microscopy (SEM) showed that a uniform distribution of SiO₂-APS on the fiber surface and the increased surface roughness. The sized fibers (CF/SiO₂-APS) exhibited a high surface free energy and good wettability based on a dynamic contact angle testing. Interfacial microstructure and mechanical properties of untreated and sized CFs composites were investigated. Simultaneous enhancements of interlaminar shear strength (ILSS) and impact toughness of CF/SiO₂-APS composites were achieved, increasing 44.79% in ILSS and 31.53% in impact toughness compared to those of untreated composites. Moreover, flexural strength and modulus of composites increased by 32.22 and 50.0% according to flexural test. In addition, the hydrothermal aging resistance of CF/SiO₂-APS composites has been improved significantly owing to the introduced Si-O-Si bonds at the interface.     

Flexible Sandwich Structural Strain Sensor Based on Silver Nanowires Decorated with Self‐Healing Substrate

Flexible and stretchable conducting composites that can sense stress or strain are needed for several emerging fields including human motion detection and personalized health monitoring. Silver nanowires (AgNWs) have already been used as conductive networks. However, once a traditional polymer is broken, the conductive network is subsequently destroyed. Integrating high pressure sensitivity and repeatable self‐healing capability into flexible strain sensors represents new advances for high performance strain sensing. Herein, superflexible 3D architectures are fabricated by sandwiching a layer of AgNWs decorated self‐healing polymer between two layers of polydimethylsiloxane, which exhibit good stability, self‐healability, and stretchability. For better mechanical properties, the self‐healing polymer is reinforced with carbon fibers (CFs). The sensors based on self‐healing polymer and AgNWs conductive network show high conductivity and excellent ability to repair both mechanical and electrical damage. They can detect different human motions accurately such as bending and recovering of the forearm and shank, the changes of palm, fist, and fingers. The fracture tensile stress of the reinforced self‐healing polymer (9 wt% CFs) is increased to 10.3 MPa with the elongation at break of 8%. The stretch/release responses under static and dynamic loads of the sensor have a high sensitivity, large sensing range, excellent reliability, and remarkable stability.     

聚醚醚酮/碳纤维复合粉末的制备及性能

将热处理改性的聚醚醚酮(PEEK)粉末和碳纤维(CF)共混制备了PEEK/CF复合粉末。采用表观密度测试、扫描电子显微镜、电子万能试验机、热重分析、差示扫描量热法等对复合粉末材料的微观形貌、力学性能和热性能进行分析。结果表明,热处理后的PEEK粉末表观密度最高可达0.286 g/cm3。与纯PEEK相比,复合粉末的玻璃化转变温度、熔融温度和分解温度都有较大的提高;随着CF质量分数逐渐增加,复合粉末材料的拉伸强度、弯曲强度、弯曲弹性模量、热变形温度和维卡软化温度逐渐增大,冲击强度逐渐减小。改性PEEK/CF复合粉末材料为选择性激光烧结技术提供了高强度、高耐热性能的粉末材料,从而应用于汽车工业、电器工业、医疗器械和航空航天等领域。     

Improved interfacial adhesion in carbon fiber/epoxy composites through a waterborne epoxy resin sizing agent

A series of self‐emulsified waterborne epoxy resin (WEP) emulsions were used as surface sizing for carbon fibers (CFs) to improve the interfacial adhesion between the CF and epoxy matrix. In this work, the hydrogenated bisphenol‐A epoxy resin (HBPAE) was modified by polyethylene glycol (PEG) with molecular weights of 400, 800, 1000, 1500, 2000, 4000, and 6000 g/mol. The properties of the WEP emulsion were examined by Fourier transform infrared spectroscopy, dynamic light scattering, and transmission electron microscopy. The surface characteristics of sized CFs were evaluated using scanning electron microscopy, atomic force microscopy, and X‐ray photoelectron spectroscopy. Afterwards, CF/EP composites were prepared and their fracture surface and interlaminar shear strength (ILSS) were examined. The results indicated that PEG2000 modified HBPAE sizing had the optimum emulsion stability and film‐forming ability. Meanwhile, the results also demonstrated that a continuous and uniform sizing layer was formed on the surface of CFs and the surface sizing was excellent in improving the chemical activity of CFs. Compared with unsized CFs, the O1s/C1s composition ratio was observed to increase from 11.51% to 33.17% and the ILSS of CF/EP composites increased from 81.2 to 89.7 MPa, exhibiting better mechanical property than that of commercial Takemoto S64 sized CFs. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44757.     

Preventing Fatal Fractures in Carbon-Fiber–Glass-Fiber-Reinforced Plastic Composites by Monitoring Change in Electrical Resistance

A method which monitors the changes in electrical resistance in CFGFRP (carbon-fiber–glass-fiber-reinforced plastics) composites was found to be a promising technique for foreseeing fractures and preventing fatal ones. CFGFRP composites containing two types of carbon fibers along with 31.6 vol% glass fibers were used. U-shaped copper electrodes were attached to both ends of the CFGFRP composites, using a conductive adhesive agent, and electrical resistance was measured via a two-thermal dc method. A strain gauge was attached onto a specimen to measure strain. On loading, the changes in electrical resistance increased linearly with increasing strain, and the value reached 38% for the CFGFRP composites containing 0.36 vol% PAN-based high-strength carbon fibers. A tremendous change in electrical resistance was seen for the CFGFRP composites containing 0.38 vol% pitch-based high-property carbon fibers, and the composites could maintain their shape owing to a hybrid effect after the carbon fibers fractured. The change in electrical resistance can be controlled through suitable selection of the type of carbon fibers according to their values of ultimate elongation. Permanent, residual electrical resistance was found to remain, and the changes in resistance were dependent on the maximum previous strain.     

Preparation of multilayered C–Si–Al2O3 coatings on continuous carbon fibers and C–Si–Al2O3-coated carbon-fiber-reinforced hydroxyapatite composites

Multilayered C–Si–Al coatings with various morphologies were deposited on carbon fibers (CFs) using magnetron sputtering. The thickness of the coatings was increased from 0.5 to 1.5 μm by magnetron sputtering between 90 and 120 min. C–Si–Al coatings of suitable thickness were heat-treated at 600 °C and transformed into C–Si–Al₂O₃ coatings by one-step anodic oxidation (AO). The oxidation time for the one/two-step anodic oxidation and the ratio of oxidation time for the two-step anodic oxidation significantly influenced the morphologies of the C–Si–Al₂O₃(AO) coatings. Al₂O₃ coatings with satisfactory morphologies and structures were prepared by two-step anodic oxidation with a total time of 30 min and a ratio of 1:1 between the initial and secondary oxidation times. The multilayered C–Si–Al₂O₃(AO) coatings were modified to C–Si–Al₂O₃ coatings by secondary heat treatment at 1050 °C. Subsequently, hot-press sintering was used to prepare CFs with multilayered C–Si–Al₂O₃ coating-reinforced hydroxyapatite (CF/C–Si–Al₂O₃/HA) composites. The multilayered C–Si–Al₂O₃-coated CFs demonstrated good resistance to oxidation and thermal shock. This could effectively protect CFs from oxidative damage and maintain its strengthening effect during sintering. The multilayered C, Si, and Al₂O₃ coatings effectively reduced the difference between the coefficient of thermal expansion of the CFs and HA matrixes. The interfacial gaps between the multilayered coatings and HA were reduced. This could enhance the mechanical performance of the composites. The CF/C–Si–Al₂O₃/HA composites exhibited improved mechanical properties with a bending strength of 83.94 ± 12.29 MPa, and fracture toughness of 2.45 ± 0.08 MPa m^1/2. This study can broaden the application of CF/C–Si–Al₂O₃/HA biocomposites as bone-repair materials and help obtain CF-reinforced composites with excellent mechanical properties that are fabricated or serviced at high temperatures.     

Self-sensing of flexural damage and strain in carbon fiber reinforced cement and effect of embedded steel reinforcing bars

Self-sensing of flexural damage and strain in carbon fiber reinforced cement is attained by measuring the volume or surface resistance with the four-probe method and electrical contacts on the compression and/or tension surfaces. The oblique resistance (volume resistance in a direction between the longitudinal and through-thickness directions) increases upon loading and is a good indicator of damage and strain in combination. The surface resistance on the compression side decreases upon loading and is a good indicator of strain. The surface resistance on the tension side increases upon loading and is a good indicator of damage. The effectiveness for the self-sensing of flexural strain in carbon fiber reinforced cement is enhanced by the presence of embedded steel rebars on the tension side. For the same midspan deflection, the fractional change in surface electrical resistance is increased in magnitude, whether the surface resistance is that of the tension side or the compression side. The fractional change in resistance of the tension surface is increased by 40%, while the magnitude of the fractional change in resistance of the compression surface is increased by 70%, due to the steel.     

High electrical conductivity of nylon 6 composites obtained with hybrid multiwalled carbon nanotube/carbon fiber fillers

The synergetic effect of multiwalled carbon nanotubes (MWNTs) and carbon fibers (CFs) in enhancing the electrical conductivity of nylon 6 (PA6) composites was investigated. To improve the compatibility between the fillers and the PA6 resin, we grafted γ‐aminopropyltriethoxy silane (KH‐550) onto the MWNTs and CFs after carboxyl groups were generated on their surface by chemical oxidation with nitric acid. Fourier transform infrared spectroscopy and thermogravimetric analysis proved that the KH‐550 molecules were successfully grafted onto the surface of the MWNTs and CFs. Scanning electron microscopy and optical microscopy showed that the obtained modified fillers reduced the aggregation of fillers and resulted in better dispersion and interfacial compatibility. We found that the electrical percolation threshold of the MWNT/PA6 and CF/PA6 composites occurred when the volume fraction of the fillers were 4 and 5%, respectively. The MWNT/CF hybrid‐filler system exhibited a remarkable synergetic effect on the electrically conductive networks. The MWNT/7% CF hybrid‐filler system appeared to show a second percolation when the MWNT volume fraction was above 4% and a volume resistivity reduction of two orders of magnitude compared with the MWNT/PA6 system. The mechanical properties of different types of PA6 composites with variation in the filler volume content were also studied. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40923.     

碳纤维增强天然橡胶复合材料性能研究

本文主要通过碳纤维添加量的不同来研究碳纤维用量对NR/CF(橡胶/碳纤维)复合材料的力学性能、导电性、导热性、加工性能和动态力学性能的影响。研究结果表明,NR/CF复合材料在添加3phr碳纤维时,力学性能最好。在添加15phr时,橡胶试样体积电阻率比未添加碳纤维的降低了3个数量级。导热系数比未添加碳纤维的试样最高提高21.8%。随着碳纤维添加量增多,试样抗湿滑性能和滚动阻力都有所上升。     

Improving the interfacial and flexural properties of carbon fiber–epoxy composites via the grafting of a hyperbranched aromatic polyamide onto a carbon fiber surface on the basis of solution polymerization

Hyperbranched aromatic polyamide (HBP) was grafted successfully onto carbon fibers (CFs) on the basis of solution polymerization to enhance the interfacial adhesion strength of CF-reinforced epoxy resin composites. The microstructure and interfacial properties of the CFs before and after decoration were researched. The results indicate that HBP was deposited uniformly onto the CFs with γ-aminopropyl triethoxysilane as the bridging agent. The active groups, roughness, and surface energy of the modified fiber [hyperbranched aromatic polyamide grafted carbon fiber (CF–HBP)] increased visibly in comparison with those of the untreated CFs. The CF–HBP composites revealed simultaneous remarkable enhancements (65.3, 34.3, and 84.8%) in their interfacial shear strength, flexural strength, and modulus, respectively; this was attributed to the improvement in the fiber–epoxy interface through enhanced chemical interactions, mechanical interlocking, and wettability. These agreed with the scanning electron microscopy observations from the fracture surface morphologies of the composites. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47232.     

Enhanced tribological performance of hybrid polytetrafluoroethylene/Kevlar fabric composite filled with milled pitch‐based carbon fibers

As self‐lubricating bearing liner materials, tribological properties of milled pitch‐based carbon fibers (CFs) modified polytetrafluoroethylene (PTFE)/Kevlar fabric composites were investigated, and the microscopic morphology of worn surface was studied. The results show that the appropriate incorporation of CFs can obviously reduce the wear rate of the fabric composite with almost unchanging friction coefficient. The wear rates of 5 wt % CF‐filled PTFE/Kevlar fabric composites are decreased by 30% and 48% for two kinds of composites made with fibers from different producers compared with unfilled fabric composites. Scanning electron microscopy observations show that the appropriate incorporation of CFs obviously improves the interfacial bonding and reduces pull‐out and fracture of Kevlar fiber. Meanwhile, the introduction of CFs at proper fraction is helpful to form smooth and continuous transfer film on the surface of metal counterpart. The improving mechanism of the CF is attributed to increasing mechanical strength, thermal conductivity and self‐lubricating effects. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46269.     

Fracture behavior of vinylester resin matrix composites reinforced with alkali‐treated jute fibers

Jute fibers were treated with 5% NaOH solution for 4 and 8 h, respectively, to study the mechanical and impact fatigue properties of jute‐reinforced vinylester resin matrix composites. Mechanical properties were enhanced in case of fiber composites treated for 4 h, where improved interfacial bonding (as evident from scanning electron microscopy [SEM]) and increased fiber strength properties contributed effectively in load transfer from the matrix to the fiber; but their superior mechanical property was not retained with fatigue, as they showed poor impact fatigue behavior. The fracture surfaces produced under a three‐point bend test and repeated impact loading were examined under SEM to study the nature of failure in the composites. In case of untreated fiber composites, interfacial debonding and extensive fiber pullout were observed, which lowered the mechanical property of the composites but improved their impact fatigue behavior. In composites treated for 4 h under repeated impact loading, interfacial debonding occurred, followed by fiber breakage, producing a sawlike structure at the fracture surface, which lowered the fatigue resistance property of the composites. The composites with fibers treated with alkali for 8 h showed maximum impact fatigue resistance. Here, interfacial debonding was at a minimum, and the fibers, being much stronger and stiffer owing to their increased crystallinity, suffered catastrophic fracture along with some microfibrillar pullout (as evident from the SEM micrographs), absorbing a lot of energy in the process, which increased the fatigue resistance property of the composites. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2588–2593, 2002     

Iron phthalocyanine coatings on the surface of carbon fibers and their improved interfacial interactions with poly(arylene ether)nitrile

Riveted carbon fibers (CFs) were fabricated via in situ thermopolymerization. Iron phthalocyanine was like rivets distributed on the surface of the acidulated CFs. The rivets were characterized by scanning electron microscopy (SEM) and distributed uniformly on the surface of the CFs with a uniform microsphere size of 120 nm. Next, the pristine and riveted CFs were used to prepare fiber‐reinforced poly(arylene ether)nitrile (PEN)‐based composites with a hot‐press molding technique. The creep behaviors of PEN on the pristine and riveted CFs were investigated by dynamic rheological measurements. Among the samples, the viscosities changed with the frequency, and the stress relaxation and Cole–Cole plots are presented and discussed in detail. These results indicated better interlocking between the PEN chains and the rivets on the surface of the CFs. The dynamic mechanical properties of the composites were examined in three‐point bending mode with a dynamic mechanical analyzer. The results indicate that the reduction of the tan δ peak height may have been due to the improved interfacial adhesion between the CFs and PEN. Additionally, the interfacial morphologies of the CF‐reinforced PEN composites were monitored; this also confirmed the improved adhesion between the PEN chains and the riveted CFs in comparison with that of the pristine CFs. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46466.     

Characterization of differently shaped carbon fiber composites prepared from naphtha cracking bottom oil

Different shaped carbon fibers (R-, I-, C-, Y-, and X-type) were prepared from melt-spinning of reformed naphtha cracking bottom oil precursors through various shaped spinnerets. These different shaped CFs (carbon fibers) and PVC (polyvinyl chloride) resin were compounded, and then CF/PVC composites were prepared. Precursor pitch, carbon fibers, and composites were characterized and their properties were compared. Mechanical properties of carbon fibers and composites were characterized relating to external surface area and ratio of perimeter to cross-sectional area of carbon fibers. The tensile strength of tetralobal fibers (X-type) showed five times higher than that of round-shaped fibers (R-type) due to extended external surface area. Their tensile strength of CF/PVC composite increased as ratio of perimeter to cross-sectional area of carbon fibers. The magnitude of the ratio was in order to X-, C-, I-, Y-, and R-type.     

腐蚀环境中纤维增强聚四氟乙烯复合材料的摩擦磨损性能研究

分别研究了不同含量碳纤维(CF)、玻璃纤维(GF)填充聚四氟乙烯（PTFE）复合材料在硫酸溶液中和干摩擦条件下的摩擦学性能,同时考察了PTFE复合材料在酸中的腐蚀行为,探讨了相关机理。结果表明,在酸中GF能够提高PTFE的耐磨性,比CF在提高PTFE耐磨性方面具有更好的优势。就酸溶液中的耐磨性和耐腐蚀性而言,15 %（质量分数,下同）是填料的最佳含量,此时GF和CF填充的PTFE,耐磨性分别较纯PTFE提高了7.7和4.4倍;当填料的含量超过15 %时,复合材料的耐磨性和耐腐蚀性均下降,主要是由于此时犁削和磨粒磨损是PTFE复合材料的主要磨损机制。由于酸溶液的冷却和润滑作用,硫酸溶液中PTFE复合材料的摩擦因数大幅降低,但酸溶液抑制了对磨面上转移膜的形成。