Nonaqueous emulsion copolymerization of ethyl methacrylate/lauryl methacrylate in propylene glycol. II. Adsorption of poly(ethylene oxide)–polystyrene–poly(ethylene oxide) triblock copolymer on latex particles

The adsorption behavior of various poly(ethylene oxide)–polystyrene–poly(ethylene oxide) (PEO‐PS‐PEO) triblock copolymer (TBC) s on acrylic latex particles in propylene glycol was studied. The composition of the PEO‐PS‐PEO triblock polymers varied from 41 to 106 in each PEO block length and from 18 to 41 in the PS block length. The location of the PEO‐PS‐PEO TBC was determined by analyzing for the physically adsorbed amount on the latex surface, the anchored mount on the surface, the entrapped amount inside the particle, and the “free” PEO‐PS‐PEO TBCs in the propylene glycol. A contour graph technique was applied to analyze the experimental data, which showed that a minimum existed for the physically adsorbed portion at a PS block length of about 30 units. When the PS block length was less than 30 units, the adsorption decreased with increasing PS block length, indicating rearrangement of mixed PEO brush and adsorbed PS block. When the PS block was greater than 30 units, the adsorption increased with increasing block length because of the poor solvency of the PS block in the propylene glycol medium, resulting in a collapse of the PS chain. Considering the binding energy between the PS block and the latex particle surface, which governs adsorption, it was hypothesized that a lower block length limit exists, below which no adsorption takes place. The solubility of the PS block in propylene glycol guides the important upper block length limit. The anchored fraction of the block copolymer increased continuously with increasing PS block length in the entire region investigated. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 1963–1975, 2001     

Chitosan‐grafted poly(hydroxyethyl methacrylate‐co‐glycidyl methacrylate) membranes for reversible enzyme immobilization

Epoxy group‐containing poly(hydroxyethyl methacrylate/glycidyl methacrylate), p(HEMA/GMA), membrane was prepared by UV initiated photopolymerization. The membrane was grafted with chitosan (CH) and some of them were chelated with Fe(III) ions. The CH grafted, p(HEMA/GMA), and Fe(III) ions incorporated p(HEMA/GMA)‐CH‐Fe(III) membranes were used for glucose oxidase (GOD) immobilization via adsorption. The maximum enzyme immobilization capacity of the p(HEMA/GMA)‐CH and p(HEMA/GMA)‐CH‐Fe(III) membranes were 0.89 and 1.36 mg/mL, respectively. The optimal pH value for the immobilized GOD preparations is found to have shifted 0.5 units to more acidic pH 5.0. Optimum temperature for both immobilized preparations was 10°C higher than that of the free enzyme and was significantly broader at higher temperatures. The apparent K_m values were found to be 6.9 and 5.8 mM for the adsorbed GOD on p(HEMA/GMA)‐CH and p(HEMA/GMA)‐CH‐Fe(III) membranes, respectively. In addition, all the membranes surfaces were characterized by contact angle measurements. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3084–3093, 2007     

Effect of coordination number on the formation of silver nanoparticles in polymer/silver salt complex membranes

Polymer/silver salt complex membranes consisting of AgBF₄ dissolved in poly(2-ethyl-2-oxazoline) (POZ) exhibited higher separation performance for propylene/propane mixtures but gradual decrease of separation properties, primarily due to the reduction of silver ions to silver nanoparticles. In this study, the effect of salt concentration on the formation of silver nanoparticles in POZ/AgBF₄ complex membranes was investigated. Separation test showed that 1/0.5 POZ/AgBF₄ complex membrane exhibited improved long-term stability on the membrane separation performance for propylene/propane mixtures compared to 1/1 POZ/AgBF₄ complex membrane. The stability improvement would be attributed to the suppression of the reduction of silver ions to silver metal nanoparticles, resulting from the higher coordination number of silver ions to carbonyl oxygens of POZ in 1/0.5 POZ/AgBF₄ membrane than 1/1 membrane. Transmission electron microscopy (TEM) and UV–visible spectra results confirmed that the rate of silver metal nanoparticle formation in the 1/0.5 POZ/AgBF₄ complex membrane was significantly retarded compared to that of 1/1 POZ/AgBF₄ complex membrane. It is therefore concluded that the coordination number of silver ions for carbonyl oxygens is of pivotal importance in controlling the reduction reaction of silver ions to silver metals and consequently improving the membrane separation performance for propylene/propane mixtures.     

NMR study of poly(vinylpyrrolidone)/poly(ethylene oxide) blends

Development of polymeric blends has become very important for polymer industries because they have been shown to be successful and versatile alternatives to obtain new polymers. In this work binary blends formed by poly(vinylpyrrolidone) (PVP) and poly(ethylene oxide) (PEO) were studied by solution and solid‐state NMR to determine their physical interaction, homogeneity, and compatibility for use as membranes to separate water/alcohol. The NMR results allowed us to acquire information on the microstructure and molecular dynamic behavior of polymer blends. From the NMR solution it was possible to evaluate the microstructure: PVP presented a preferential syndiotactic distribution sequence and PEO presented two regions, one crystalline and the other amorphous. Considering the solid‐state NMR results it was possible to evaluate the molecular dynamics and all binary blends, showing that PEO behaves as a plasticizer; some intermolecular interaction was also observed. An important point was to evaluate the microstructure of the carbonyl PVP using cross polarization/magic‐angle spinning (CP/MAS) and CP/MAS/dipolar decoupling that was not observed before. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2820–2823, 2002     

Immobilization of poly(ethylene oxide) on poly(ethylene terephthalate) using a plasma polymerization process

Poly(ethylene oxide) (PEO) has been covalently immobilized on poly(ethylene terephthalate) (PET) films using a radio frequency glow discharge polymer deposition process, followed by chemical coupling. Amino or hydroxyl groups were introduced onto the surface of the PET by exposing the films to allylamine and allyl alcohol plasmas. These functional groups were activated with cyanuric chloride, and then they were reacted with PEO. ESCA and water contact angle studies were used to characterize the surfaces of these films during the different stages of the reaction. The films containing the higher molecular weight PEO exhibited an increase in the ? C? O? peak of the C_ls ESCA spectrum and an increase in oxygen content on the film surfaces. Increasing the molecular weight of the PEO attached to the PET also resulted in an increased wettability of the films.     

Shape‐memory behaviors of electrospun chitosan/poly(ethylene oxide) composite nanofibrous membranes

With aim of constructing a class of functional environmentally friendly materials, we electrospun chitosan (CS) blends with various contents of poly(ethylene oxide) (PEO) into a series of composite nanofibrous membranes exhibiting shape‐memory behaviors. In the present composite system, CS and PEO served as hard and soft domains, respectively. The CS, presenting no thermal transition, and the PEO, with apparent melting–crystallization, were demonstrated by differential scanning calorimetry testing. Characterizations also revealed that the morphologies of the CS/PEO membranes were controlled by the mass ratios of CS/PEO. The composite fibrous membranes showed great mechanical performances and thermal stabilities as well. Moreover, CS/PEO possessed excellent shape‐memory behaviors. Such fibrous membranes could complete their shape‐recovery processes within 20 s at the temperature of 20°C above the melting transition temperature (T_m). Both the shape fixity and shape‐recovery ratios were higher than 90%, even after five cycles. The CS/PEO fibrous membranes present significant potential applications in the field of biotechnology and tissue engineering, such as in scaffolds and smart tubes. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42532.     

Hydrogels based on poly(ethylene oxide) and poly(tetramethylene oxide) or poly(dimethyl siloxane). II. Physical properties and bacterial adhesion

To investigate the effects of polymer chemistry and topology on physical properties and bacterial adhesion, various hydrogels composed of short hydrophilic [poly(ethylene oxide) (PEO)] and hydrophobic blocks were synthesized by polycondensation reactions. Differential scanning calorimetry and X‐ray diffraction analysis confirmed that all of the hydrogels were strongly phase‐separated due to incompatibility between PEO and hydrophobic blocks such as poly(tetramethylene oxide) (PTMO) and poly(dimethyl siloxane) (PDMS). The crystallization of PEO in the hydrogels was enhanced by the incorporation of longer PEO chains, the adoption of PDMS as a hydrophobic block, and the grafting of monomethoxy poly(ethylene oxide) (MPEO). Compared to Pellethane, the control polymer, the hydrogels exhibited higher Young's moduli and elongations at break, which was attributed to the crystalline domains of PEO and the flexible characteristics of the hydrophobic blocks. The mechanical properties of the hydrogels, however, significantly deteriorated when they were hydrated in distilled water; this was primarily ascribed to the disappearance of PEO crystallity. The water capacity of hydrogels at 37°C in phosphate‐buffered saline (PBS) (pH = 7.4) was dominantly dependant on PEO content, which also influenced the thermonegative swelling behavior. From the bacterial adhesion tests, it was evident that both S. epidermidis and E. coli adhered to Pellethane much greater than to the hydrogels, regardless of the preadsorption of albumin. Better resistance to bacterial adhesion was observed in hydrogels with longer PEO chains, with PTMO as a hydrophobic block, and with MPEO grafts. The least bacterial adhesion for both species was achieved on MPEO_2k–PTMO, a hydrogel with MPEO grafts. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1505–1514, 2003     

Immobilization of invertase onto crosslinked poly(p‐chloromethylstyrene) beads

Invertase was immobilized onto poly(p‐chloromethylstyrene) (PCMS) beads that were produced by a suspension polymerization with an average size of 186 μm. The beads had a nonporous but reasonably rough surface. Because of this, a reasonably large external surface area (i.e., 14.1 m²/g) could be achieved with the proposed carrier. A two‐step functionalization protocol was followed for the covalent attachment of invertase onto the bead surface. For this purpose, a polymeric ligand that carried amine groups, polyethylenimine (PEI), was covalently attached onto the bead surface by a direct chemical reaction. Next, the free amine groups of PEI were activated by glutaraldehyde. Invertase was covalently attached onto the bead surface via the direct chemical reaction between aldehyde and amine groups. The appropriate enzyme binding conditions and the batch‐reactor performance of the immobilized enzyme system were investigated. Under optimum immobilization conditions, 19 mg of invertase was immobilized onto each gram of beads with 80% retained activity after immobilization. The effects of pH and temperature on the immobilized invertase activity were determined and compared with the free enzyme. The kinetic parameters K_M and V_M were determined with the Michealis–Menten model. K_M of immobilized invertase was 1.75 folds higher than that of the free invertase. The immobilization caused a significant improvement in the thermal stability of invertase, especially in the range of 55–65°C. No significant internal diffusion limitation was detected in the immobilized enzyme system, probably due to the surface morphology of the selected carrier. This result was confirmed by the determination of the activation energies of both free and immobilized invertases. The activity half‐life of the immobilized invertase was approximately 5 times longer than that of the free enzyme. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1268–1279, 2002     

Synthesis and characterization of poly(N‐isopropylacrylamide)s initiated with siloxane oligomer–(NH4)2Ce(NO3)6 redox pair

Poly(N‐isopropylacrylamide)s (PNIPAAM)s were synthesized via free‐radical polymerization using a ceric ammonium nitrate, Ce(IV)–α‐ω‐dihydroxy(polydimethylsiloxane) (Tegomer H‐Si 2111, PDMS) redox pair in hexane at 30°C in a nitrogen atmosphere. The dependence of the initiation and termination steps on the [NIPAAM]/[Ce(IV)] and [NIPAAM]/[PDMS] ratios were studied using gravimetry and FTIR, ¹H‐NMR, UV‐vis, and GFAA spectroscopy techniques. Gravimetric results indicated that, in the case of high concentrations of PDMS, the percentage of the solid portions of the products decreased while the amount of the oligomeric NIPAAM chains increased, that is, as the amount of PDMS in hexane was increased, the number of the short NIPAAM chains having PDMS segments at the two ends, also increased. UV‐vis results showed that the LCST of PNIPAAM initiated with Ce(IV) alone was higher than those of the ones that were synthesized using common initiator systems such as an ammonium persulfate–N,N,N′,N′‐tetramethylethylenediamine redox pair and azobis(isobutyronitrile). Further, it was observed that both siloxane blocks and ? NH? groups forming coordination bonds with free Ce(IV) ions and/or metal–ligand complexes had an important effect on the aggregation process of the chains. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1248–1254, 2003     

Permeation Characteristics of Light Hydrocarbons Through Poly(amide-6-β-ethylene oxide) Multilayer Composite Membranes

In this paper, poly(amide-6-β-ethylene oxide) (PEBA1657) copolymer was used to prepare multilayer polyetherimide (PEI)/polydimethylsiloxane (PDMS)/PEBA1657/PDMS composite membranes by dip-coating method. Permeation behaviors of ethylene, ethane, propylene, propane, n-butane, methane and nitrogen through the multilayer composite membranes were investigated over a range of operating temperature and pressure. The permeances of light hydrocarbons through PEI/PDMS/PEBA1657/PDMS composite membranes increase with their increasing condensability, and the olefins are more permeable than their corresponding paraffins. For light hydrocarbons, the gas permeances increase significantly as temperature increasing. When the transmembrane pressure difference increases, the gas permeance increases moderately due to plasticization effect, while their apparent activation energies for permeation decrease.     

Modification of poly(octadecene‐alt‐maleic anhydride) films by reaction with functional amines

Thin films of poly(octadecene‐alt‐maleic anhydride) on top of Si wafers and glass plates were modified by reactions with different functional amines to be used in future studies on the relevance of certain molecular surface properties for the covalent immobilization of proteins. For that aim, a strategy was developed and applied to convert the anhydride moieties of the copolymer by functional amines into side chains bearing hydrophilic groups of acidic (carboxylic acid, sulfonic acid), basic (amines), or neutral (poly(ethylene oxide) (PEO), glucose) character. The modification of the copolymer films was achieved through the two‐step formation of a cyclic imide, which was very stable in aqueous solution. Depending on the reactivity of the applied amine, the adjustment of the reaction time was suitable for the preparation of partially converted surfaces of the polymer film. Degrees of modification between 5 and 30% (according to X‐ray photoelectron spectroscopy data) were obtained. Annealing the modified polymer films induced efficient back‐formation of the anhydride groups. By reaction of the layered polyanhydrides with highly crosslinked diamines, amine‐functionalized polymer films were produced that were capable of binding secondary polyanhydride layers. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1255–1266, 2003     

A novel electron beam-based method for the immobilization of trypsin on poly(ethersulfone) and poly(vinylidene fluoride) membranes

A novel technique for the covalent immobilization of trypsin in a one-step reaction using low-energy electron beam is described. The enzyme immobilization was applied on poly(ethersulfone) and poly(vinylidene fluoride) microfiltration membranes. For this purpose, the membranes were dipped in an aqueous solution of trypsin followed by electron beam treatment.The effect of irradiation conditions on the immobilization was investigated, as well as the resulting membrane properties with respect to enzymatic activity, immobilized enzyme concentration, pure water flux, scanning electron microscopy, and porosimetry. This technique shall provide a simple, inexpensive method for enzyme immobilization on various polymer membranes and offer a tool for the application in enzymatic membrane reactors.     

Morphology of poly(styrene‐block‐dimethylsiloxane) copolymer films

The morphologies of poly(styrene‐block‐di‐methylsiloxane) (PS‐b‐PDMS) copolymer thin films were analyzed via atomic force microscopy and transition electron microscopy (TEM). The asymmetric copolymer thin films spin‐cast from toluene onto mica presented meshlike structures, which were different from the spherical structures from TEM measurements. The annealing temperature affected the surface morphology of the PS‐b‐PDMS copolymer thin films; the polydimethylsiloxane (PDMS) phases at the surface were increased when the annealing temperature was higher than the PDMS glass‐transition temperature. The morphologies of the PS‐b‐PDMS copolymer thin films were different from solvent to solvent; for thin films spin‐cast from toluene, the polystyrene (PS) phase appeared as pits in the PDMS matrix, whereas the thin films spin‐cast from cyclohexane solutions exhibited an islandlike structure and small, separated PS phases as protrusions over the macroscopically flat surface. The microphase structure of the PS‐b‐PDMS copolymer thin films was also strongly influenced by the different substrates; for an asymmetric block copolymer thin film, the PDMS and PS phases on a silicon substrate presented a lamellar structure parallel to the surface at intervals. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1010–1018, 2007     

Poly(2‐hydroxyethylmethacrylate)/chitosan dye and different metal‐ion‐immobilized interpenetrating network membranes: Preparation and application in metal affinity chromatography

Composite membranes were synthesized with 2‐hydroxyethylmethacrylate and chitosan (pHEMA/chitosan) via an ultraviolet‐initiated photopolymerization technique in the presence of an initiator (α,α′‐azobisisobutyronitrile). The interpenetrating network (IPN) membranes were improved by the immobilization of dye molecules via hydroxyl and amino groups on the membrane surfaces from the IPNs. A triazidine dye (Procion Green H‐4G) was covalently immobilized as a ligand onto the IPN membranes. The protein showed various affinities to different chelated metal ions on the membrane surfaces that best matched its own distribution of functional sites, resulting in a distribution of binding energies. In support of this interpretation, two different metal ions, Zn(II) and Fe(III), were chelated with the immobilized dye molecules. The adsorption and binding characteristics of the different metal‐ion‐chelated dye‐immobilized IPN membranes for the lysozyme were investigated with aqueous solutions in magnetically stirred cells. The experimental data were analyzed with two adsorption kinetic models, pseudo‐first‐order and pseudo‐second‐order, to determine the best fit equation for the adsorption of lysozyme onto IPN membranes. The second‐order equation for the lysozyme–dye–metal‐chelated IPN membrane systems was the most appropriate equation for predicting the adsorption capacity for all the tested adsorbents. The reversible lysozyme adsorption on the dye‐immobilized and metal‐ion‐chelated membranes obeyed the Temkin isotherm. The lysozyme adsorption capacity of the pHEMA/chitosan dye, pHEMA/chitosan dye–Zn(II), and pHEMA/chitosan dye–Fe(III) membranes were 2.54, 2.85, and 3.64 mg cm^?2, respectively. The nonspecific adsorption of the lysozyme on the plain pHEMA/chitosan membrane was about 0.18 mg cm^?2. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1843–1853, 2003     

Biodegradable block copolymers with poly(ethylene oxide) and poly(glycolic acid‐valine) blocks

Biodegradable ABA triblock copolymers with poly(ethylene oxide) and poly(glycolic acid‐valine) blocks were synthesized via ring‐opening polymerization of cyclo(glycolic acid‐valine) using Ca‐alcoholates of hydroxytelechelic PEO as the initiator. The L‐valine residue racemized during copolymerization of cyclo(glycolic acid‐valine). The crystallization of the block copolymers decreases with decreasing PEO content in the triblock copolymers and with increasing length of the poly(glycolic acid‐valine) block. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2916–2919, 2002     

Synthesis and characterization of poly(ester ether siloxane)s

A series of novel thermoplastic elastomers based on ABA‐type triblock prepolymers, poly[(propylene oxide)–(dimethylsiloxane)–(propylene oxide)] (PPO‐PDMS‐PPO), as the soft segments, and poly(butylene terephthalate) (PBT), as the hard segments, was synthesized by catalyzed two‐step melt transesterification of dimethyl terephthalate (DMT) with 1,4‐butanediol (BD) and α,ω‐dihydroxy‐(PPO‐PDMS‐PPO) (M?_n = 2930 g mol^?1). Several copolymers with a content of hard PBT segments between 40 and 60 mass% and a constant length of the soft PPO‐PDMS‐PPO segments were prepared. The siloxane‐containing triblock prepolymer with hydrophilic terminal PPO blocks was used to improve the compatibility between the polar comonomers, i.e. DMT and BD, and the non‐polar PDMS segments. The structure and composition of the copolymers were examined using ¹H NMR spectroscopy, while the effectiveness of the incorporation of α,ω‐dihydroxy‐(PPO‐PDMS‐PPO) prepolymer into the copolyester chains was controlled by chloroform extraction. The effect of the structure and composition of the copolymers on the transition temperatures (T_m and T_g) and the thermal and thermo‐oxidative degradation stability, as well as on the degree of crystallinity, and some rheological properties, were studied. Copyright © 2006 Society of Chemical Industry     

Syntheses of poly(methyl methacrylate)/poly(dimethyl siloxane) graft copolymers and their surface enrichment of their blend with acrylate adhesive copolymers

Several types of poly(methyl methacrylate)/poly(dimethyl siloxane) graft copolymers (PMMA‐g‐PDMS) were synthesized using macromonomer technology. Three types of PMMA‐g‐PDMS with different PDMS chain length were obtained. The effect of siloxane chain length on surface segregation of PMMA‐g‐PDMS/poly(2‐ethylhexyl acrylate‐co‐acrylic acid‐co‐vinyl acetate)[P(2EHA‐AA‐VAc)] blends was investigated. The blends of PMMA‐g‐PDMS with P(2EHA‐AA‐VAc) showed surface segregations of PDMS components. The surface enrichments of PDMS in the blends depended on the PDMS chain length, significantly. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1736–1740, 2002     

Enhancement of the retention performance of the poly(ethylene oxide) — tannic acid system by poly (diallyldimethyl ammonium chloride)

The retention performance of the poly(ethylene oxide) (PEO) and tannic acid (TA) dual system was studied in the presence of poly(diallyldimethyl ammonium chloride) (PDADMAC). The zeta potential, and size of the association complex between PEO and TA in the presence of PDADMAC as well as the infrared spectra of TA and the PEO-TA system were also studied. It was shown that hydrogen bonds are formed between the phenolic and acidic groups of TA and the oxygen atoms of the PEO macromolecules. Moreover, it was found that the presence of small quantities of PDADMAC enhances the fibre fines and clay first pass retention. The maximum effect was observed with an amount of added PDADMAC equal to 20% of the amount of added PEO. Further addition of PDADMAC was found to decrease the retention probably because it re-charges the surface to positive. When clay was replaced by ground calcium carbonate no retention improvement was detected. This is most likely due to the presence of calcium ions.     

Study on a water‐swellable rubber compatibilized by amphiphilic block polymer based on poly(ethylene oxide) and poly(butyl acrylate)

A water‐swellable rubber (WSR), compatibilized by the amphiphilic block copolymer, has been prepared by blending a natural rubber (NR) matrix with crosslinked sodium polyacrylate (CSP), poly(ethylene oxide)‐b‐poly(butyl acrylate) (PEO‐b‐PBA), poly(ethylene glycol) (PEG), reinforced filler, and vulcanizing agents. The preparation process was described. The microphase structure of WSR was characterized by a scanning electron microscopy (SEM) photograph. The dependence of the degree of the water‐absorbing and the water‐swelling, the water‐absorbing and water‐swelling rates on CSP, PEG, and PEO‐b‐PBA contents were investigated. The compatibilizing mechanism of PEO‐b‐PBA on WSR was studied. And the optimum composition range was identified: CSP (30–60 phr), PEG (10–20 phr) PEO‐b‐PBA (PEO/PBA = 0.36, 5 phr). © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 3120–3125, 2002     

Immobilization of glucoamylase on magnetic poly(styrene) particles

Magnetic poly(styrene) particles including active groups were prepared for enzyme immobilization without any activation process. Glucoamylase, which is widely used in industry, was immobilized onto these particles. The effects of pH, buffer concentration, and temperature on immobilization were investigated; moreover, the effect of immobilization temperature on immobilized glucoamylase activity was determined for the hydrolysis of maltose. The acetate buffer with the concentration of 6 × 10⁻⁴ M at pH 4 and 20–30°C was found as the most suitable medium for the immobilization of the glucoamylase. The amount of bound protein is 8 mg/g particle with the immobilization yield of 70%. The maximum activity obtained with immobilized glucoamylase is approximately 70% of the free one. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 69–73, 1999