Modification of cyanate ester resin by poly(ethylene phthalate) and related copolyesters

Aromatic polyesters were prepared and used to improve the brittleness of the cyanate ester resin. The aromatic polyesters include poly(ethylene phthalate) (PEP) and poly(ethylene phthalate‐co‐1,4‐phenylene phthalate). The polyesters were effective modifiers for improving the brittleness of the cyanate ester resin. For example, inclusion of 20 wt % PEP (MW 19,800) led to a 120% increase in the fracture toughness (K_IC) with retention in flexural properties and a slight loss of the glass transition temperature compared to the mechanical and thermal properties of the unmodified cured cyanate ester resin. The microstructures of the modified resins were examined by scanning electron microscopy and dynamic viscoelastic analysis. The thermal stability of the modified resins was lower than that of the unmodified resin as determined by thermogravimetric analysis. The water absorptivity of the modified resin increased significantly, compared to that of the unmodified cured cyanate ester resin. The toughening mechanism was discussed in terms of the morphological and dynamic viscoelastic behaviors of the modified cyanate ester resin system. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 208–219, 2000     

Preparation of novel soluble poly(ester imide)s containing a trimellitimide moiety and their use as modifiers for aromatic diamine‐cured epoxy resin

Poly(ester imide)s, prepared by the reaction of phthalic anhydride, N‐(4‐carboxyphenyl) trimellitimide and 1,2‐ethanediol, were used to improve the toughness of bisphenol‐A diglycidyl ether epoxy resin cured with 4,4′‐diaminodiphenyl sulfone (DDS). The poly(ester imide)s include poly(ethylene phthalate‐co‐ethylene N‐(1,4‐phenylene) trimellitimide dicarboxylate)s (PESIs) having 10, 20 and 30 mol% trimellitimide (TI) units, respectively. PESIs having 10 and 20 mol% TI units were effective as modifiers for toughening the cured epoxy resin. For example, the inclusion of 20 wt% of PESI (20 mol% TI unit, M _W 19300 g mol^?1) led to a 55% increase in the fracture toughness (K_IC) of the cured resin (with an increase in flexural strength and modulus) and the modified resin had a particulate morphology. PESI having 30 mol% TI units was not effective because of degradation of the modifier by DDS. The toughening mechanism is discussed in terms of morphological and dynamic viscoelastic behaviour of the modified epoxy resin system. © 2001 Society of Chemical Industry     

Toughening of epoxy resins by modification with aromatic polyesters

Aromatic polyesters, prepared by the reaction of phthalic or isophthalic acids and α,ω-alkanediols, were used to reduce the brittleness of bisphenol-A diglycidyl ether epoxy resin cured with methyl hexahydrophthalic anhydride. These polyesters were effective as modifiers for toughening of the epoxy resin system. The most suitable composition for modification of the epoxy resins was inclusion of 20 wt % of poly(ethylene phthalate) (MW 7200), which resulted in a 150% increase in the fracture toughness (K_IC) of the cured resin at no expense of its mechanical properties. The effectiveness of poly(alkylene phthalate)s as modifiers decreased with increasing the chain length of alkylene units. The toughening mechanism was discussed based on the morphological and dynamic mechanical behaviors of the modified epoxy resin system.     

Modification of aromatic diamine-cured epoxy resins by poly(oxymethylene) or hybrid modifiers containing poly(oxymethylene)

A copolymer comprising poly(oxymethylene) (POM, polyacetal) was used to improve the fracture toughness of a resin based on diglycidyl ether of bisphenol A (DGEBA) cured with 3,3′-dimethyl-5,5′-diethyl-4,4′-diaminodiphenyl methane. POM was a less effective modifier for epoxies and a third component was used as a toughener or a compatibilizer for POM. The third component includes polypropylene glycol-type urethane prepolymer (PU) and aromatic polyesters. The hybrid modifiers composed of POM and PU were more effective as modifiers for toughening epoxies than POM alone. In the ternary DGEBA/POM/PU (90/10/10wt ratio) blend, the fracture toughness, K_IC, for the modified resin increased 50% with retention of flexural properties and a slight decrease in glass transition temperature (T_g) compared with those of the unmodified epoxy resin. The aromatic polyesters include poly(ethylene phthalate) (PEP), the related copolyesters and poly(butylene phthalate). PEP was most effective of them as a third component in the hybrid modifier. In the ternary DGEBA/POM/PEP (85/15/10) blend, K_IC for the modified resin increased 70% with medium loss of flexural strength and retention of T_g. The toughening mechanism is discussed in terms of morphological and dynamic viscoelastic behaviour of the modified epoxy resin systems. ©1997 SCI     

Preparation of poly(1,4‐cyclohexylenedimethylene phthalate)s and their use as modifiers for aromatic diamine‐cured epoxy resin

Poly(1,4‐cyclohexylenedimethylene phthalate) s, prepared by the reaction of phthalic anhydride and 1,4‐cyclohexane dimethanol (35/65 or 73/27 mol % cis/trans or trans alone), have been used to improve the toughness of bisphenol‐A diglycidyl ether epoxy resin cured with 4,4′‐diaminodiphenyl sulfone. The aromatic polyesters include poly(cis/trans‐1,4‐cyclohexylenedimethylene phthalate) (PCP) based on a commercial cyclohexanedimethanol, poly(trans‐1,4‐cyclohexylenedimethylene phthalate) (trans‐PCP) and poly(cis/trans‐1,4‐cyclohexylenedimethylene phthalate) (cis‐rich PCP) prepared from a cis‐rich diol. The polyesters used were soluble in the epoxy resin without solvents and were effective as modifiers for toughening the cured epoxy resin. For example, the inclusion of 20 wt% of PCP (MW 6400 g mol⁻¹) led to an 80% increase in the fracture toughness (K_IC) of the cured resin with no loss of mechanical and thermal properties. The toughening mechanism is discussed in terms of morphological and dynamic viscoelastic behaviours of the modified epoxy resin system. © 2000 Society of Chemical Industry     

Toughening of aromatic diamine-cured epoxy resins by poly(butylene phthalate)s and the related copolyesters

Aromatic polyesters, prepared by the reaction of aromatic dicarboxylic acids and 1,4-butanediol, were used to improve the toughness of bisphenol-A diglycidyl ether epoxy resin cured with p,p′-diaminodiphenyl sulfone. These polyesters contained poly(butylene phthalate)s (PBP), poly(butylene phthalate-co-butylene isophthalate)s, poly(butylene phthalate-co-butylene terephthalate)s, and poly(butylene phthalate-co-butylene 2,6-naphthalene dicarboxylate)s. All aromatic polyesters used in this study were soluble in the epoxy resin without solvents and were found to be effective as modifiers for toughening the cured epoxy resin. For example, the inclusion of 20 wt % PBP (MW 16,300) led to a 120% increase in the fracture toughness (K_IC) of the cured resin with no loss of mechanical and thermal properties. The toughening mechanism was discussed in terms of the morphological and dynamic viscoelastic behaviors of the modified epoxy resin system. © 1996 John Wiley & Sons, Inc.     

Studies on isotactic poly(phenyl glycidyl ether)‐modified epoxy resins. II. Toughening of epoxy resins

A semicrystalline polymer, isotactic poly(phenyl glycidyl ether) (i‐PPGE) was used as a modifier for epoxy resin; 1,8‐Diamino‐p‐methane (MNDA) and 4,4′‐Diamino diphenyl sulfone (DDS) were used as curing agents. In the MNDA‐cured resins, the dispersed phase were spherical particles with diameters in the range of 0.5–1.0 μm when the resin was blended with 5 phr i‐PPGE. In the DDS‐cured resins, the particle size distribution of the dispersed phase was much wider. The difference was traced back to the reactivity of the curing agent and the different regimes used for curing. Through dynamic mechanical analysis, it was found that in the MNDA‐cured systems, i‐PPGE had a lower crystallinity than in the DDS‐cured system. In spite of the remarkable difference in the morphology and microstructure of the modified resins cured with these two curing agents, the toughening effects of i‐PPGE were similar for these resins. The critical stress intensity factor (K_IC) was increased by 54% and 53%, respectively, for the resins cured by DDS and by MNDA, blending with 5 phr of the toughner. i‐PPGE was comparable with the classical toughners carboxyl‐terminated butadiene‐acrylonitrile copolymers in effectiveness of toughening the epoxy resin. An advantage of i‐PPGE was that the modulus and the glass‐transition temperature of the resin were less affected. However, this modifier caused the flexural strength to decrease somewhat. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1223–1232, 2002; DOI 10.1002/app.10445     

Modification of bismaleimide resin by poly(ethylene phthalate‐co‐ethylene terephthalate), poly(ethylene phthalate‐co‐ethylene 4,4′‐biphenyl dicarboxylate), and poly(ethylene phthalate‐co‐ethylene 2,6‐naphthalene dicarboxylate)

Aromatic polyesters were prepared and used to improve the brittleness of bismaleimide resin, composed of 4,4′‐bismaleimidodiphenyl methane and o,o′‐diallyl bisphenol A (Matrimid 5292 A/B resin). The aromatic polyesters included PEPT [poly(ethylene phthalate‐co‐ethylene terephthalate)], with 50 mol % of terephthalate, PEPB [poly(ethylene phthalate‐co‐ethylene 4,4′‐biphenyl dicarboxylate)], with 50 mol % of 4,4′‐biphenyl dicarboxylate, and PEPN [poly(ethylene phthalate‐co‐ethylene 2,6‐naphthalene dicarboxylate)], with 50 mol % 2,6‐naphthalene dicarboxylate unit. The polyesters were effective modifiers for improving the brittleness of the bismaleimide resin. For example, inclusion of 15 wt % PEPT (MW = 9300) led to a 75% increase in fracture toughness, with retention in flexural properties and a slight loss of the glass‐transition temperature, compared with the mechanical and thermal properties of the unmodified cured bismaleimide resin. Microstructures of the modified resins were examined by scanning electron microscopy and dynamic viscoelastic analysis. The toughening mechanism was assessed as it related to the morphological and dynamic viscoelastic behaviors of the modified bismaleimide resin system. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 2352–2367, 2001     

Modification of bismaleimide resin by soluble poly(ester imide) containing trimellitimide moieties

Poly(ester imide)s containing trimellitimide moieties have been used to reduce the brittleness of the bismaleimide resin composed of 4,4′‐bismaleimidediphenyl methane and o,o′‐diallyl bisphenol A. The poly(ester imide)s include poly[ethylene phthalate‐co‐ethylene N‐(1,4‐phenylene)trimellitimide dicarboxylate]s containing 20–40 mol% trimellitimide (TI) unit, and poly[trimethylene phthalate‐co‐trimethylene N‐(1,4‐phenylene)trimellitimide dicarboxylate]s (PESIP) containing 20 mol% TI unit. The poly(ester imide)s are effective modifiers for reducing the brittleness of the bismaleimide resin. For example, when using 30 wt% of PESIP (20 mol% TI unit, M_w 13 500 g mol^?1), the fracture toughness (K_IC) for the modified resin is increased by 80% with retention in flexural properties and a slight loss of the glass transition temperature, compared with the values of the unmodified cured bismaleimide resin. Microstructures of the modified resins have been examined by scanning electron microscopy and dynamic viscoelastic analysis. The toughening mechanism is discussed in terms of the morphological and dynamic viscoelastic behaviour of the modified bismaleimide resin system. © 2004 Society of Chemical Industry     

Toughening of bismaleimide resin by modification with poly(ethylene phthalate) and poly(ethylene phthalate-co-ethylene isophthalate)

Aromatic polyesters were prepared and used to improve the brittleness of the bismaleimide resin composed of 4,4′-bismaleimidediphenyl methane and o,o′-diallyl bisphenol A. The aromatic polyesters contain poly(ethylene phthalate) (PEP) and poly(ethylene phthalate-co-ethylene isophthalate) (10 mol % isophthalate unit) (PEPI). PEP and PEPI were effective modifiers for improving the brittleness of the bismaleimide resin. The most suitable composition for the modification of the bismaleimide was inclusion of 20 wt % PEP (MW 18,200), which led to an 80% increase in the fracture toughness with retention of flexural properties and a slight decrease in the glass transition temperature, compared with the mechanical and thermal properties of the unmodified cured bismaleimide resin (Matrimid resin). Microstructures of the modified resins were examined by scanning electron microscopy and dynamic viscoelastic analysis. The thermal stability of the modified resin was slightly lower than that of the unmodified resin by thermogravimetric analysis. The toughening mechanism is discussed in terms of the morphological and dynamic viscoelastic behavior of the modified bismaleimide resin system. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 65: 1349–1357, 1997     

Study of ionic polymer toughening epoxy resin

In this study, PEL [copolymer of poly(propylene) oxide (PPO) and poly(ethylene oxide) (PEO)] toughening epoxy resin with ionic charge was used to produce an interpenetrating action between the cross‐linking network structure of the epoxy resin and the PEL additive. Fourier transform infrared (FTIR) analysis of the toughening epoxy resin revealed that ? NCO disappeared at 2400 cm^?1, ? NH appeared at 3300 cm^?1, and ? C?O appeared at 1750 cm^?1. These results indicate that a urethane bond was produced. Dynamic mechanical analysis (DMA) and mechanical testing results indicated that as the level of PEL increased, the compatibility between the epoxy resin and PEL also increased. In addition, the compatibility was improved because the addition of cornate hardener produced a graft phenomenon. The tensile property, impact strength, and fracture toughness of PEL toughening epoxy resin all had a tendency to improve. The tensile strength, impact strength, and fracture toughness (K_IC value) were most improved when 30 phr cornate was added. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 3740–3751, 2002     

Preparation and properties of dynamically cured PP/MAH‐g‐EVA/epoxy blends

A method concerning with the simultaneous reinforcing and toughening of polypropylene (PP) was reported. Dynamical cure of the epoxy resin with 2‐ethylene‐4‐methane‐imidazole (EMI‐2,4) was successfully applied in the PP/maleic anhydride‐grafted ethylene‐vinyl acetate copolymer (MAH‐g‐EVA), and the obtained blends named as dynamically cured PP/MAH‐g‐EVA/epoxy blends. The stiffness and toughness of the blends are in a good balance, and the smaller size of epoxy particle in the PP/MAH‐g‐EVA/epoxy blends shows that MAH‐g‐EVA was also used as a compatibilizer. The structure of the dynamically cured PP/MAH‐g‐EVA/epoxy blends is the embedding of the epoxy particles by the MAH‐g‐EVA. The cured epoxy particles as organic filler increases the stiffness of the PP/MAH‐g‐EVA blends, and the improvement in the toughness is attributed to the embedded structure. The tensile strength and flexural modulus of the blends increase with increasing the epoxy resin content, and the impact strength reaches a maximum of 258 J/m at the epoxy resin content of 10 wt %. DSC analysis shows that the epoxy particles in the dynamically cured PP/MAH‐g‐EVA/epoxy blends could have contained embedded MAH‐g‐EVA, decreasing the nucleating effect of the epoxy resin. Thermogravimetric results show the addition of epoxy resin could improve the thermal stability of PP, the dynamically cured PP/MAH‐g‐EVA/epoxy stability compared with the pure PP. Wide‐angle x‐ray diffraction analysis shows that the dynamical cure and compatibilization do not disturb the crystalline structure of PP in the blends. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Toughening of aromatic diamine-cured trifunctional epoxy resins by modification with N-phenylmaleimide–styrene copolymers containing pendant p-hydroxyphenyl groups

N-Phenylmaleimide (PMI)–N-(p-hydroxy)phenylmaleimide (HPMI)–styrene (St) terpolymers (HPMS), containing pendant p-hydroxyphenyl (HP) groups, were prepared and used to improve the toughness of triglycidyl aminocresol epoxy resin cured with p,p′-diaminodiphenyl sulfone. HPMS was effective as a modifier for the toughening of the epoxy resin. When using 15 wt % of HPMS (1.0 mol % HP unit, M_w 129,000), the fracture toughness (K_IC) for the modified resin increased 190% with a medium loss of flexural strength. The toughening of epoxies could be attained because of the cocontinuous phase structure of the modified resins. The decrease in flexural strength was suppressed to some extent by introducing a functional group into the modifier. The toughening mechanism was discussed in terms of the morphological behavior of the modified epoxy resin system. © 1995 John Wiley & Sons, Inc.     

Enhanced fracture toughness of epoxy resins with novel amine‐terminated poly(arylene ether sulfone)–carboxylic‐terminated butadiene‐acrylonitrile–poly(arylene ether sulfone) triblock copolymers

Amine‐terminated poly(arylene ether sulfone)–carboxylic‐terminated butadiene‐acrylonitrile–poly(arylene ether sulfone) (PES‐CTBN‐PES) triblock copolymers with controlled molecular weights of 15,000 (15K) or 20,000 (20K) g/mol were synthesized from amine‐terminated PES oligomer and commercial CTBN rubber (CTBN 1300x13). The copolymers were utilized to modify a diglycidyl ether of bisphenol A epoxy resin by varying the loading from 5 to 40 wt %. The epoxy resins were cured with 4,4′‐diaminodiphenylsulfone and subjected to tests for thermal properties, plane strain fracture toughness (K_IC), flexural properties, and solvent resistance measurements. The fracture surfaces were analyzed with SEM to elucidate the toughening mechanism. The properties of copolymer‐toughened epoxy resins were compared to those of samples modified by PES/CTBN blends, PES oligomer, or CTBN. The PES‐CTBN‐PES copolymer (20K) showed a K_IC of 2.33 MPa m^0.5 at 40 wt % loading while maintaining good flexural properties and chemical resistance. However, the epoxy resin modified with a CTBN/8K PES blend (2:1) exhibited lower K_IC (1.82 MPa m^0.5), lower flexural properties, and poorer thermal properties and solvent resistance compared to the 20K PES‐CTBN‐PES copolymer‐toughened samples. The high fracture toughness with the PES‐CTBN‐PES copolymer is believed to be due to the ductile fracture of the continuous PES‐rich phases, as well as the cavitation of the rubber‐rich phases. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1556–1565, 2002; DOI 10.1002/app.10390     

Toughening of aromatic diamine-cured epoxy resins by modification with hybrid modifiers composed of N-phenylmaleimide–styrene copolymers and N-phenylmaleimide–styrene–p-hydroxystyrene terpolymers

Hybrid modifiers composed of N-phenylmaleimide–styrene copolymers (PMS), and N-phenylmaleimide–styrene–p-hydroxystyrene terpolymers (PMSH) containing pendent p-hydroxyphenyl groups as functionalities, were used to improve the toughness of bisphenol-A diglycidyl ether epoxy resin cured with p,p′-diaminodiphenyl sulphone. The hybrid modifiers were effective in toughening the epoxy resin. When using the modifier composed of 10 wt% PMS (M?_w 313000) and 2.5 wt% PMSH (2.5 mol% p-hydroxystyrene units, M?_w 316000), the fracture toughness (K_IC) for the modified resins increased 100% with no deterioration in the flexural properties and the glass transition temperature. The improvement in toughness of the epoxy resins was attained because of the co-continuous phase structure and the improvement in interfacial adhesion. The toughening mechanism is discussed in terms of the morphological characteristics of the modified epoxy resin systems.     

Synthesis and characterization of chlorinated soy oil based epoxy resin/glass fiber composites

Composites with good toughness properties were prepared from chemically modified soy epoxy resin and glass fiber without additional petroleum based toughening agent. Chlorinated soy epoxy (CSE) resin was prepared from soybean oil. The CSE was characterised by spectral, and titration method. The prepared CSE was blended with commercial epoxy resin in different ratios and cured at 85°C for 3 h, and post cured at 225°C for 2 h using m‐phenylene diamine (MPDA) as curing agent. The cure temperatures of epoxy/CSE/MPDA with different compositions were found to be in the range of (151.2–187.5°C). The composite laminates were fabricated using epoxy /CSE/MPDA‐glass fiber at different compositions. The mechanical properties such as tensile strength (248–299 MPa), tensile modulus (2.4–3.4 GPa), flexural strength (346–379 MPa), flexural modulus (6.3–7.8 GPa) and impact strength (29.7–34.2) were determined. The impact strength increased with the increase in the CSE content. The interlaminor fracture toughness (G_IC) values also increased from 0.6953 KJ/m² for neat epoxy resin to 0.9514 KJ/m² for 15%CSE epoxy‐modified system. Thermogravimetric studies reveal that the thermal stability of the neat epoxy resin was decreased by incorporation of CSE. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Graft‐interpenetrating polymer networks of epoxy with polyurethanes derived from poly(ethyleneterephthalate) waste

Polyester polyurethanes derived from poly(ethyleneterephthalate) (PET) glycolysates were blended with epoxy to form graft‐interpenetrating networks (IPNs) with improved mechanical properties. Microwave‐assisted glycolytic depolymerization of PET was performed in the presence of polyethylene glycols of different molecular weights (600–1500). The resultant hydroxyl terminated polyester was used for synthesis of polyurethane prepolymer which was subsequently reacted with epoxy resin to generate grafted structures. The epoxy‐polyurethane blend was cured with triethylene tetramine under ambient conditions to result in graft IPNs. Blending resulted in an improvement in the mechanical properties, the extent of which was found to be dependant both on the amount as well as molecular weight of PET‐based polyurethane employed. Maximum improvement was observed in epoxy blends prepared with polyurethane (PU1000) at a loading of 10% w/w which resulted in 61% increase in tensile strength and 212% increase in impact strength. The extent of toughening was quantified by flexural studies under single edge notch bending (SENB) mode. In comparison to the unmodified epoxy, the Mode I fracture toughness (K_IC) and fracture energy (G_IC) increased by ～45% and ～184%, respectively. The underlying toughening mechanisms were identified by fractographic analysis, which generated evidence of rubber cavitation, microcracking, and crack path deflection. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40490.     

Preparation and properties of bio‐based epoxy montomorillonite nanocomposites derived from polyglycerol polyglycidyl ether and ε‐polylysine

Glycerol polyglycidyl ether (GPE) and polyglycerol polyglycidyl ether (PGPE) were cured with ε‐poly(L ‐lysine) (PL) using epoxy/amine ratios of 1 : 1 and 2 : 1 to create bio‐based epoxy cross‐linked resins. When PGPE was used as an epoxy resin and the epoxy/amine ratio was 1 : 1, the cured neat resin showed the greatest glass transition temperature (T_g), as measured by differential scanning calorimetry. Next, the mixture of PGPE, PL, and montomorillonite (MMT) at an epoxy/amine ratio of 1 : 1 in water was dried and cured finally at 110°C to create PGPE‐PL/MMT composites. The X‐ray diffraction and transmission electron microscopy measurements revealed that the composites with MMT content 7–15 wt % were exfoliated nanocomposites and the composite with MMT content 20 wt % was an intercalated nanocomposite. The T_g and storage modulus at 50–100°C for the PGPE‐PL/MMT composites measured by DMA increased with increasing MMT content until 15 wt % and decreased at 20 wt %. The tensile strength and modulus of the PGPE‐PL/MMT composites (MMT content 15 wt %: 42 and 5300 MPa) were much greater than those of the cured PGPE‐PL resin (4 and 6 MPa). Aerobic biodegradability of the PGPE‐PL in an aqueous medium was ～ 4% after 90 days, and the PGPE‐PL/MMT nanocomposites with MMT content 7–15 wt % showed lower biodegradability. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Improving the toughness of epoxy with a reactive tetrablock copolymer containing maleic anhydride

Reactive block copolymers (BCPs) provide a unique means for toughening epoxy thermosets because covalent linkages provide opportunities for greater improvement in the fracture toughness (K_IC). In this study, a tailored reactive tetrablock copolymer, poly[styrene‐alt‐(maleic anhydride)]‐block‐polystyrene‐block‐poly(n‐butyl acrylate)‐block‐polystyrene, was incorporated into a diglycidyl ether of bisphenol A based epoxy resin. The results demonstrate the advantage of reactive BCP in finely tuning and controlling the structure of epoxy blends, even with 95 wt % epoxy‐immiscible triblocks. The size of the dispersed phase was efficiently reduced to submicrometer level. The mechanical properties, such as K_IC, of these cured blends were investigated. The addition of 10 wt % reactive BCP into the epoxy resins led to considerable improvements in the toughness, imparting nearly a 70% increase in K_IC. The designed reactive tetrablock copolymer opened good prospects because of its potential novel applications in toughening modification of engineering polymer composites. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 132, 42826.     

Anticorrosive properties of epoxy resin coatings cured by aniline/p‐phenylenediamine copolymer

Aniline/p‐phenylenediamine copolymer [poly(ANI‐co‐p‐PDA)] was prepared by chemical oxidative polymerization. FTIR and ¹H‐NMR analysis indicate that the poly(ANI‐co‐p‐PDA) is oligomer with end‐capped amino groups, which can cure epoxy resin. The anticorrosion performance of carbon steel (CS) samples coated by epoxy resin coating cured with poly(ANI‐co‐p‐PDA) and epoxy resin coating cured with triethylenetetramine exposed to 5 wt % NaCl and 0.1 mol/L HCl aqueous solution is studied by the potentiodynamic polarization and electrochemical impedance spectroscopy. The results show that the CS coated by epoxy resin coating cured with poly (ANI‐co‐p‐PDA) has more excellent corrosion protection than that of epoxy resin coating cured with triethylenetetramine. Raman spectroscopy analysis indicates that the surface of CS coated by epoxy resin coating cured with poly(ANI‐co‐p‐PDA) forms passive layer, which is composed of α‐Fe₂O₃. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009