Design of Sub-1 mW CMOS LC VCO based on current reused topology with Q-enhancement and body-biased technique

A CMOS LC voltage controlled oscillator (VCO) based on current reused topology with low phase noise and low power consumption is presented for IEEE 802.11a (Seller et al. A 10 GHz distributed voltage controlled oscillator for WLAN application in a VLSI 65 nm CMOS process, in: IEEE Radio Frequency Integrated Circuits (RFIC) Symposium, 3–5 June, 2007, pp. 115–118.) application. The chip1 is designed with the tail current-shaping technique to obtain the phase noise −116.1 dBc/Hz and power consumption 3.71 mW at the operating frequency 5.2 GHz under supply voltage 1.4 V. The second chip of proposed VCO can achieve power consumption Sub 1 mW and is still able to maintain good phase noise. The current reused and body-biased architecture can reduce power consumption, and better phase noise performance is obtained through raising the Q value. The measurement result of the VCO oscillation frequency range is from 5.082 GHz to 5.958 GHz with tuning range of 15.8%. The measured phase noise is −115.88 dBc/Hz at 1 MHz offset at the operation frequency of 5.815 GHz. and the dc core current consumption is 0.71 mA at a supply voltage of 1.4 V. Its figure of merit (FOM) is −191 dBc/Hz. Two circuits were taped out by TSMC 0.18 μm 1P6M process.     

Design of a three-stage ring-type voltage-controlled oscillator with a wide tuning range by controlling the current level in an embedded delay cell

This paper presents a new design for a three-stage voltage-controlled differential ring oscillator embedded with a delay cell for a wide tuning range from 59 MHz to 2.96 GHz by adjusting the current level in the delay cell. The ring oscillator consists of a voltage-to-current converter, coder circuit, three-stage ring with delay cells, and current monitoring circuit to extend the tuning range of the proposed voltage-controlled oscillator. Each functional block has been designed for a minimum power consumption using the TSMC 0.18 μm CMOS technology. We simulate the performances of the proposed voltage-controlled oscillator in terms of phase noise, power consumption, tuning range, and gain. Our simulation results show that the proposed oscillator has the linear frequency–voltage characteristics over a wide tuning range. At each tuning range (mode), the calculated phase noise of the proposed ring oscillator at each tuning range (mode) was −87, −85, −81, and −79 dBc/Hz at a 1 MHz offset from the center frequency. The DC power of the proposed voltage-controlled oscillator consumed 0.86–3 mW under a 1.8 V supply voltage.     

Design of a 30 GHz rotary traveling wave oscillator with improved frequency tuning range in 0.18 μm CMOS technology

In this paper, the operation of rotary traveling wave oscillators is analyzed, the general oscillation condition is derived, and analytical formula for the oscillator loss is presented. Based on this analysis, switched transmission line is employed to extend the output frequency tuning range. Post-layout simulation shows a frequency tuning range of 3.1 GHz in the vicinity of 30 GHz. The proposed half-quadrature VCO exhibits a phase noise better than −102.2 dBc/Hz at 1 MHz offset frequency. The VCO provides an output power level ranging from −6 to −2.5 dBm with drawing 15.2 mA of dc current from a 1.8 V power supply.     

A 1-V 4-GHz wide tuning range voltage-controlled ring oscillator in 0.18 μm CMOS

A new differential delay cell with complementary current control to extend the control voltage range as well as the operation frequency is proposed for low voltage and wide tuning range voltage-controlled ring oscillator (VCRO). The complementary current control can get rid of the restriction that control voltage is unable to cover the full range of power supply voltage in a conventional VCRO. A three-stage VCRO chip working with 1 V power supply voltage is constructed using 0.18 μm 1P6M CMOS process for verifying the efficacy of the proposed differential delay cell. Measured results of the VCRO chip show that a wide range of operation frequency from 4.09 GHz to 479 MHz, a tuning range of 88%, is achieved for the full range of control voltage from 0 to 1 V. The power consumptions of the chip are 13 and 4 mW for oscillation outputs of 4.09 GHz and 479 MHz, respectively. The measured phase noise is −93.3 dBc/Hz at 1 MHz offset from 4.09 GHz center frequency. The core area of the chip is 106 μm×76.2 μm.     

Design and noise analysis of a fully-differential charge pump for phase-locked loops

A fully-differential charge pump (FDCP) with perfect current matching and low output current noise is realized for phase-locked loops (PLLs). An easily stable common-mode feedback (CMFB) circuit which can handle high input voltage swing is proposed. Current mismatch and current noise contribution from the CMFB circuit is minimized. In order to optimize PLL phase noise, the output current noise of the FDCP is analyzed in detail and calculated with the sampling principle. The calculation result agrees well with the simulation. Based on the noise analysis, many methods to lower output current noise of the FDCP are discussed. The fully-differential charge pump is integrated into a 1-2 GHz frequency synthesizer and fabricated in an SMIC CMOS 0.18 μm process. The measured output reference spur is -64 dBc to -69 dBc. The in-band and out-band phase noise is -95 dBc/Hz at 3 kHz frequency offset and -123 dBc/Hz at 1 MHz frequency offset respectively.     

基于802．11a标准的5GHz振荡器设计

介绍了一种全集成的LC压控振荡器（VCO）的设计。该振荡器的中心频率为5．25GHz,电源电压为1．8V,工作在802．11a标准下,采用0．18μmCMOS工艺实现。仿真结果表明。VCO的相位噪声在偏离中心频率1MHz时达到-121dBc／Hz,调谐范围达到31％,输出电压峰峰值为830mV,有良好的线性纯度。     

Design of a tunable multi-band differential LC VCO using 0.35 μm SiGe BiCMOS technology for multi-standard wireless communication systems

In this paper, an integrated 2.2-5.7 GHz multi-band differential LC VCO for multi-standard wireless communication systems was designed utilizing 0.35 μm SiGe BiCMOS technology. The topology, which combines the switching inductors and capacitors together in the same circuit, is a novel approach for wideband VCOs. Based on the post-layout simulation results, the VCO can be tuned using a DC voltage of 0 to 3.3 V for 5 different frequency bands (2.27-2.51 GHz, 2.48-2.78 GHz, 3.22-3.53 GHz, 3.48-3.91 GHz and 4.528-5.7 GHz) with a maximum bandwidth of 1.36 GHz and a minimum bandwidth of 300 MHz. The designed and simulated VCO can generate a differential output power between 0.992 and −6.087 dBm with an average power consumption of 44.21 mW including the buffers. The average second and third harmonics level were obtained as −37.21 and −47.6 dBm, respectively. The phase noise between −110.45 and −122.5 dBc/Hz, that was simulated at 1 MHz offset, can be obtained through the frequency of interest. Additionally, the figure of merit (FOM), that includes all important parameters such as the phase noise, the power consumption and the ratio of the operating frequency to the offset frequency, is between −176.48 and −181.16 and comparable or better than the ones with the other current VCOs. The main advantage of this study in comparison with the other VCOs, is covering 5 frequency bands starting from 2.27 up to 5.76 GHz without FOM and area abandonment. Output power of the fundamental frequency changes between −6.087 and 0.992 dBm, depending on the bias conditions (operating bands). Based on the post-layout simulation results, the core VCO circuit draws a current between 2.4-6.3 mA and between 11.4 and 15.3 mA with the buffer circuit from 3.3 V supply. The circuit occupies an area of 1.477 mm² on Si substrate, including DC, digital and RF pads.     

New implementation of injection locked technique and its application to low phase noise quadrature oscillators

A new implementation of the injection locked technique is proposed. The incident signal is directly injected into the common-source connection node of the sub-harmonic oscillator instead of the gate of the tail current source, and a narrowband noise filtering network is inserted into the same node to suppress the tail current source noise. A novel quadrature oscillator with the proposed injection locked technique is presented. The simulations show that the phase noise of the quadrature oscillator is about 7 dB better than that of the stand-alone sub-harmonic oscillator. The quadrature oscillator has been implemented in 0.25 um CMOS process and the measured results show that the proposed quadrature oscillator could achieve a phase noise of −130 dBc/Hz at 1 MHz offset from 1.13 GHz carrier while only drawing an 8.0 mA current from the 2.5 V power supply.     

A 1.41–1.72 GHz sigma-delta fractional-N frequency synthesizer with a PVT insensitive VCO and a new prescaler

A 1.41–1.72 GHz fractional-N phase-locked loop (PLL) frequency synthesizer with a PVT insensitive voltage-controlled oscillator (VCO) is presented. In this PLL, a VCO with process, voltage, and temperature (PVT) insensitive bias circuit, and a divided-by-7/8 prescaler with improved multi-phase frequency divider are adopted. A novel multi-stage noise shaping (MASH) sigma-delta modulator (SDM) is adopted here. A new combination of low-current-mismatch charge pump (CP) and a phase/frequency detector (PFD) is proposed in this paper. Using Hejian Technology CMOS 0.18 μm analog and digital mixed-mode process, a fractional-N PLL prototype circuit is designed, the VCO in the prototype circuit can operate at a central frequency of 1.55 GHz, and its phase noise is −121 dBc/Hz at 1.0 MHz, the variety of phase noise is depressed by about 1.4 dB with the help of PVT insensitive bias. Under a 1.8-V supply voltage, the phase noise of the PLL is −113 dBc/Hz at 1.0 MHz.     

Design of self-bias tail transistor technique for low phase noise CMOS VCO with harmonic suppression using capacitance ground

This paper presents a low phase noise wideband CMOS VCO based on the self-bias tail transistor technique and harmonic suppression using a capacitance ground. This VCO utilizes switching capacitor arrays in which four channels are able to be selected for multi-band application. Moreover, the design of CMOS VCO makes good use of the self-bias tail transistor and capacitance ground filter technique to reduce the phase noise. The MOS varactors are used as fine tuning for wideband operating application. The fully integrated VCO provides excellent performance with high FOM −193 dBc/Hz. The bandwidth of the frequency is 1.1 GHz and the tuning range is 13.8%. The power dissipation of the core circuit is 8.28 mW under a 1.8 V supply and phase noise is measured as low as −123.6 dBc/Hz at 1 MHz offset under 8.5 GHz oscillation frequencies. This VCO was made by the TSMC 0.18 μm 1P6M CMOS standard process and the chip area is 0.75×0.69 (mm²).     

A wide band differentially switch-tuned CMOS monolithic quadrature VCO with a low Kvco and high linearity

A wide band, differentially switch-tuned CMOS monolithic LC-VCO is presented in this paper, as well as a frequency divider for high linearity, low Kvco quadrature signal generation. A linearity control logic is proposed. The Kvco linearity is improved to be lower than 17.68 MHz/V. By using the proposed CML DFF, the operating frequency of the frequency divider is increased by 20% with a power consumption of 3.6 mW. The proposed design has been fabricated and verified in a 0.18 μm CMOS process. The QVCO is tuned in a combined way of continuous technology and 4 bit binary switch capacitor array (SCA) discrete tuning technology. The measurement indicates that the QVCO has a 19.7% tuning range from 1.816 to 2.213 GHz. The measured phase noise is −112.25 dBc/Hz at 1 MHz offset from the 1.819 GHz carrier and draws a current of 4.0 mA around at a 1.8 V supply.     

A 0.18 μm CMOS ring VCO for clock and data recovery applications

In this paper, a 3.125 GHz four stage voltage controlled ring oscillator is presented. The oscillator has been designed in a 0.18 μm CMOS process with a 1.8 V supply. Behavioral simulations predict an 18% tuning range for the oscillator, with −91 dBc/Hz phase noise at 1 MHz offset. Its power consumption has been simulated to be as low as 15.3 mW and the variation of its DC level of oscillation is 20 mV, which corresponds to 1.3% of its mean value. While consuming less area than an LC VCO, the proposed oscillator design achieves a more stable and reliable operation point.     

A 5-GHz fully integrated full PMOS low-phase-noise LC VCO

A 5-GHz fully integrated, full PMOS, low-phase-noise and low-power differential voltage-controlled oscillator (VCO) is presented. This circuit is implemented in a 0.35-/spl mu/m four-metal BiCMOS SiGe process. At 2.7-V power supply voltage and a total power dissipation of only 13.5 mW, the proposed VCO features a worst case phase noise of -97 dBc/Hz and -117 dBc/Hz at 100 kHz and 1 MHz frequency offset, respectively. The oscillator is tuned from 5.13 to 5.68 GHz with a tuning voltage varying from 0 to 2.7 V.     

A low power current-reuse LC-VCO with an adaptive body-biasing technique

This work presents a low-power low-phase noise current-reuse LC voltage controlled oscillator (VCO) with an adaptive body-biasing technique that enhances the reliability of the proposed circuit under process, voltage, and temperature (PVT) variations. Furthermore, the supply voltage and power consumption of the proposed VCO are reduced by the start-up oscillation condition that is provided by the adaptive body-biased circuit. This property is in fact very interesting from the power management perspective. The proposed VCO works at carrier frequency of 1.8 GHz and draws the power of only 306 µW from a 0.9 V supply. It achieves phase noise of −123.36 dBc/Hz at 1 MHz offset and provides a figure-of-merit (FoM) of −193.61 dBc/Hz. The post-layout simulation results of designed VCO in 0.18 µm standard CMOS technology confirm the effectiveness of the proposed circuit.     

CMOS低相位噪声压控振荡器的设计

基于65 nm CMOS标准工艺库,设计了一个工作频率在10 GHz的具有低相位噪声的CMOS电感电容型压控振荡器。该压控振荡器选用CMOS互补交叉耦合型电路结构,采用威尔逊型尾电流源负反馈技术来降低相位噪声。仿真结果表明,此压控振荡器工作频率覆盖范围为9.9~11.2 GHz,调谐范围为12.3%,中心频率为10.5 GHz,在频率偏移中心频率1 MHz下的相位噪声为-113.3 dBc/Hz,核心功耗为2.25 mW。     

An integrated up-converter circuit in 0.8 μm SiGe technology for TV applications

This paper describes an up-converter circuit for a TV tuner chain that can be implemented in both analog and digital TV systems. The circuit is integrated into a low cost standard two metal layer 0.8 μm SiGe technology and is composed with class AB Gilbert cell based active mixer and differential voltage-controlled oscillator (VCO). The use of a high quality balanced inductor in the VCO allows achieving a measured oscillator phase noise of −104.2 dBc/Hz at 100 kHz from the carrier. The frequency conversion is from TV standard IF to RF. The results obtained in a frequency up-conversion from 36 to 1775 MHz are: a conversion gain of −2.25 dB, a noise figure of 14.4 dB and an OIP3 value of 9.1 dBm. The core power consumption is 33 mA from 5 V power supply.     

A novel current reference based on subthreshold MOSFETs with high PSRR

A novel current reference based on subthreshold MOSFETs with high power supply rejection ratio (PSRR) is presented. The proposed circuit takes full advantages of the I-V transconductance characteristics of MOSFET operating in the subthreshold region and the enhancement pre-regulator with the high gain negative feedback loop for the current reference core circuit. The proposed circuit, designed with the SMIC 0.18 μm standard CMOS logic process technology, exhibits a stable current of about 1.701 μA with much low temperature coefficient of 2.5×10⁻⁴ μA/°C in the temperature range of −40 to 150 °C at 1.5 V supply voltage, and also achieves a best PSRR over a broad frequency. The PSRR is about −126 dB at dc frequency and remains −92 dB at the frequency higher 1 MHz. The proposed circuit operates stably at the supply voltage higher 1.2 V and has good process compatibility.     

适用于2．4GHz锁相环LC压控振荡器设计

本文设计了一种适用于2．4GHz锁相环的LC压控振荡器,采stoic0．13ffCMOS工艺,中心频率2．4GHz,频率调谐范围136MHz,在1．8v电压下工作时,静态电流为5mA,在偏离中心频率1MHz处,测得相位噪声为-111dBc／Hz。     

A low-phase-noise 900-MHz CMOS ring oscillator with quadrature output

A 900-MHz two-stage CMOS voltage controlled ring oscillator (VCRO) with quadrature output is presented. The circuit is designed in a 0.18-um CMOS technology and operated on a 1.8-V supply voltage. The VCRO have a tuning range of 730 MHz to 1.43 GHz and good tuning linearity. Between 0 V and 1.1 V of control voltage, the gain of VCRO is around −620 MHz/V. At 900 MHz, the phase noise of the VCRO is −106.1 dBc/Hz at 600-KHz frequency offset with power consumption of 65.5 mW.     

A Low-Voltage Quadrature CMOS VCO Based on Voltage-Voltage Feedback Topology

A novel low-voltage quadrature voltage-controlled oscillator (QVCO) with voltage feedback to the input gate of a switching amplifier is proposed and implemented using the standard TSMC 0.18-mum CMOS 1P6M process. The proposed circuit topology is made up of two low-voltage LC-tank VCOs, where the coupled QVCO is obtained using the transformer coupling technique. At the 0.7-V supply voltage, the output phase noise of the VCO is -124.9 dBc/Hz at 1-MHz offset frequency from the carrier frequency of 2.4GHz, and the figure of merit is -185.35dBc/Hz. Total power consumption is 5.18 mW. Tuning range is about 135 MHz while the control voltage was tuned from 0 to 0.7V