High Strain, 〈001〉 Textured 0.675Pb(Mg1/3Nb2/3)O3–0.325PbTiO3 Ceramics: Templated Grain Growth and Piezoelectric Properties

Lead magnesium niobate–lead titanate, 0.675Pb(Mg_1/3Nb_2/3)O₃–0.325PbTiO₃ (PMN–32.5PT) ceramics were textured (grain-oriented) in the 〈001〉-crystallographic direction by the templated grain growth process. The textured PMN–32.5PT ceramics were produced by orienting {001}-SrTiO₃ (ST) platelets (∼10 μm in diameter and ∼2-μm thickness) in a submicron PMN–32.5PT matrix. The templated growth of 〈001〉-oriented PMN–32.5PT grains on the ST platelets resulted in textured ceramics with ∼70% Lotgering factor and >98% theoretical density. Unlike most lead-based ceramics, excess PbO was not needed for sintering or grain growth. Based on unipolar stain-field measurements at 0.2 Hz, the textured samples displayed >0.3% strain at 50 kV/cm. Low-field d ₃₃-coefficients of >1600 pC/N (<5 kV/cm) were measured directly from unipolar measurements. The low drive field d ₃₃-piezoelectric coefficient of the highly textured samples is two times greater than polycrystalline PMN–32.5PT.     

Large Pyroelectric Effect in Relaxor-Based Ferroelectric Pb(Mg1/3Nb2/3)O3–PbTiO3 Single Crystals

The pyroelectric properties of (1− x )Pb(Mg_1/3Nb_2/3)O_{3− x} PbTiO₃ (PMN− x PT) single crystals with various compositions and orientations have been investigated using a dynamic method. Excellent pyroelectric performances can be achieved in 〈111〉-oriented rhombohedral PMN− x PT (0.24≤ x ≤0.30) crystals, where the measurement direction corresponds to the polar axis of the crystal. At room temperature, the pyroelectric coefficient and the detectivity figure of merit ( F _d ) for the 〈111〉-oriented PMN–0.28PT single crystal are 8.55 × 10⁻⁴ C·(m²·K)⁻¹ and 9.89 × 10⁻⁵ Pa^−1/2 (100 Hz), respectively, superior to those of the widely used pyroelectric materials. They are also weak temperature dependent and nearly independent of frequency. These outstanding pyroelectric performances make the single crystals a promising candidate for uncooled infrared detectors and thermal imagers.     

Influence of Non-Stoichiometry on the Structure and Properties of Ba(Zn1/3Nb2/3)O3 Microwave Dielectrics: I. Substitution of Ba3W2O9

A narrow region of Zn-vacancy-containing cubic perovskites was formed in the (1− x )Ba₃(ZnNb₂)O₉−( x )Ba₃W₂O₉ system up to 2 mol% substitution ( x =0.02). The introduction of cation vacancies enhanced the stability of the 1:2 B-site ordered form of the structure, Ba(Zn_{1− x} □ _x )_1/3(Nb_{1− x} W _x )_2/3O₃, which underwent an order–disorder transition at 1410°C, ∼35° higher than pure Ba(Zn_1/3Nb_2/3)O₃. The Zn vacancies also accelerated the kinetics of the ordering reaction, and samples with x =0.006 comprised large ordered domains with a high lattice distortion ( c/a =1.226) after a 12 h anneal at 1300°C. The tungstate-containing solid solutions can be sintered to a high density at 1390°C, and the resultant ordered ceramics exhibit some of the highest microwave dielectric Q factors ( Q × f =1 18 000 at 8 GHz) reported for a niobate-based perovskite.     

π-Rotation Faults in Hexagonal BaTiO3

Planar defects in the metastably retained h-BaTiO₃ exhibiting α-fringe pattern have been characterized via transmission electron microscopy (TEM). The eligible fault vectors were determined by adopting the invisibility criteria of 2πg·R = 0 or 2 n π augmented by high-resolution imaging. Three stacking faults, F₁, F₂, and F₃, of the extrinsic nature have been fully analyzed. The eligible fault vectors for faults F₁ and F₃ contained a basal component respectively of ⅓[0001] and ⅙[0001] and a common prismatic component of ⅓〈10[1-macr]0〉. However, only three of the 〈10[1-macr]0〉 vectors are the eligible prismatic component for the fault vectors R_F1=⅓[0[1-macr]11], ⅓[10[1-macr]1], and ⅓[[1-macr]101], and R_F3=⅙[02[2-macr]1], ⅙[2[2-macr]01], and ⅙[[2-macr]021] that have fulfilled the invisibility criteria. On the other hand, all fault vectors R_F21=⅙〈[4-macr]223〉 for fault F₂, containing six vectors of the 〈[2-macr]110〉 family, is eligible. Unlike the faults of πR_F=⅙〈[2-macr]203〉 found in the D0₁₉ intermetallics of Ni₃Sn and Co₃W, neither fault F₁ nor F₃ is the π-rotation type. Fault F₂, however, is a π-rotation fault since a 60°-rotation clockwise about [0001] has produced another eligible fault vector.     

A-Site and B-Site Order in (Na1/2La1/2)(Mg1/3Nb2/3)O3 Perovskite

(Na_1/2La_1/2)(Mg_1/3Nb_2/3)O₃ undergoes a series of phase transitions that involve cation order on the A- and B-sites of the parent perovskite structure. At high temperatures both sites contain a random distribution of cations; below 1275°C a 〈111〉 layering of Mg and Nb leads to the formation of a 1:2 ordered structure with a monoclinic supercell. A second transition was observed at 925°C, where the Na and La cations order onto alternate A-site positions along the 〈001〉 direction of the parent subcell. By quenching samples from above 1275°C to preserve the disorder on the B-site, a fourth variant of this compound was obtained by inducing A-site order through a subsequent anneal at 900°C. Although the changes in structure do not produce significant alterations in the relative permittivity (ɛ_r∼ 35), they do have a significant effect on the value of the temperature coefficient of the capacitance.     

Microstructure and Microwave Dielectric Properties of (1−x)Ca(Mg1/3Ta2/3)O3/xCaTiO3 Ceramics

Dense (1− x )Ca(Mg_1/3Ta_2/3)O₃/ x CaTiO₃ ceramics (0.1≤ x ≤0.9) were prepared by a solid-state reaction process. The crystal structures and microstructures were characterized by X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. Single-phase solid solutions were obtained in the entire composition range. Long-range 1:2 ordering of B-site cations and oxygen octahedra tilting lead to the monoclinic symmetry with space group P 2₁/ c for x =0.1. For x above 0.1, the long-range ordering was destroyed and the crystal structure became the orthorhombic with space group Pbnm . The microwave dielectric properties showed a strong dependence on the composition and microstructure. The dielectric constant and temperature coefficient of resonant frequency increased nonlinearly as the CaTiO₃ content increased while the Qf values decreased approximately linearly. Good combination of microwave dielectric properties was obtained at x =0.45, where ɛ_r=45.1, Qf =34 800 GHz, and τ_f=17.4 ppm/°C.     

Formation and Structural Characterization of 1:1 Ordered Perovskites in the Ba(Zn1/3Ta2/3)O3–BaZrO3 System

The phase stabilities in the(1−x)Ba(Zn_1/3Ta_2/3)O₃ (BZT)-xBaZrO₃(BZ)system have been investigated using samples prepared by the mixed oxide method. The substitution of Zr⁴⁺destabilizes the 1:2 cation ordering in BZT and pro-motes the formation of a cubic, 1:1 ordered structure with a doubled perovskite repeat. The homogeneity range of the 1:1 phase extends from x = 0.04 to approximately x = 0.25; substitutions beyond this range stabilize a disordered perovskite. The limits of stability of the 1:1 ordering coin-cide with compositions previously found to exhibit anoma-lies in their dielectric loss. The range of homogeneity is consistent with a "random layer" model for the 1:1 ordered "Ba{β';_1/2β^1/2}O₃" structure. In this model the B× positions are assumed to be occupied exclusively by Ta⁵⁺, and the b× sites by a random distribution of Zn₂₊, Zr₄₊, and the remaining Ta 5+ cations. The validity of the model, where the ordered solid solutions can be represented by Ba{[Zn_{2− y /3}Ta_{(1−2 y )/3}Zr y ]_1/2[Ta]_1/2}O₃(y =2x)was con-firmed by Rietveld refinements conducted using data col-lected with a synchrotron X-ray source.     

Preparation of 〈110〉-Textured BaTiO3 Ceramics by the Reactive-Templated Grain Growth Method Using Needlelike TiO2 Particles

Dense, highly 〈110〉-textured BaTiO₃ ceramics were prepared by the reactive-templated grain growth method. Needlelike TiO₂ (rutile) particles with their needle axis parallel to 〈001〉 were used as reactive template particles. Slurry containing an equimolar mixture of TiO₂ and BaCO₃ was tape cast to form a green compact, in which TiO₂ particles were aligned with their needle axis parallel to the casting direction. Calcination of the green compact changed TiO₂ particles into BaTiO₃ grains with their 〈110〉 direction parallel to the casting direction, for which the topotaxial relation of was responsible. Sintering yielded a dense, highly textured BaTiO₃ compact.     

Influence of Non-Stoichiometry on the Structure and Properties of Ba(Zn1/3Nb2/3)O3 Microwave Dielectrics. IV. Tuning τf and the Part Size Dependence of Q×f

High Q ceramics of Ba₃W₂O₉ (BW)-substituted Ba(Zn_1/3Nb_2/3) O₃ (BZN) were prepared with a zero τ_f through the partial substitution of Zn by Ni and Co. The small concentrations of B-site vacancies introduced by the substitution of BW accelerated the kinetics and stability of the cation ordering and lowered the sintering temperature. Dense, zero τ_f, ordered solid solutions such as 0.99Ba(Zn_0.3Co_0.7)_1/3Nb_2/3O₃–0.01BW with ɛ_r=34.4 and Q × f =82 000 at ∼8 GHz could be obtained after sintering at 1380°C for 5 h and annealing at 1300°C for 24 h. Partially ordered ceramics in the Zn/Co and Zn/Ni solid solutions show a large gradient in the ordering throughout the pellets, which produces a resonant frequency dependence of their Q × f value. The ordering gradient is associated with the increased constraints on the growth of the 1:2 ordered structure within the interior of larger and thicker pellets and can be minimized by extended annealing.     

Structural and Dielectric Properties of Ag(Nb0.8Ta0.2)1−xSbxO3 (x≤0.08) Ceramics

Sb₂O₅ were selected to substitute (Nb_0.8Ta_0.2)₂O₅ and the effects of Sb substitution on the dielectric properties of Ag(Nb_0.8Ta_0.2)O₃ ceramics were studied. The perovskite Ag(Nb_0.8Ta_0.2)_{1− x} Sb _x O₃ ceramics showed no obvious change with x value being no more than 0.08, and the pseudoperovskite unit cell parameters a = c , b and monoclinic angle β decrease with Sb concentration increasing. The dielectric properties of Ag(Nb_0.8Ta_0.2)_{1− x} Sb _x O₃ ceramics were found to be affected greatly by the substitution of Sb for Nb/Ta. The ɛ value of Ag(Nb_0.8Ta_0.2)_{1− x} Sb _x O₃ ceramics sintered at their densified temperature increased from 480 to 825 with x from 0 to 0.08, the tan δ value decreased sharply from 0.0065 to 0.0023 (at 1 MHz) with x increasing from 0 to 0.04, and then kept a stable lower tan δ value ∼0.0024 with x to 0.08. The temperature coefficient of capacitance values continuously decreased from a positive value of 1450 ppm/°C for x =0 to a negative value of −38.52 ppm/°C for x =0.08.     

Phase Structure and Electrical Properties of (K0.48Na0.52)(Nb0.95Ta0.05)O3-LiSbO3 Lead-Free Piezoelectric Ceramics

(1− x )(K_0.48Na_0.52)(Nb_0.95Ta_0.05)O₃– x LiSbO₃ [(1− x )KNNT− x LS] lead-free piezoelectric ceramics were prepared by the conventional solid-state sintering method. A morphotropic phase boundary (MPB) between orthorhombic and tetragonal phases was identified in the composition range of 0.03< x <0.05. The ceramics near the MPB exhibit a strong compositional dependence and enhanced electrical properties. The (1− x )KNNT– x LS ( x =0.04) ceramics exhibit good electrical properties ( d ₃₃=250 pC/N, k _p=45.1%, k _t =46.3%, T _c=348°C, T _{o − t} =74°C, P _r=25.9 μC/cm², E _c=10.7 kV/cm, ɛ_r∼1352, tan δ∼3%). These results show that (1− x )KNNT– x LS ceramic is a promising lead-free piezoelectric material.     

Dependence of the Microstructure and the Electrical Properties of Lanthanum-Substituted (Na1/2Bi1/2)TiO3 on Cation Vacancies

The sintering and electrical characteristics of La-modified Na_1/2Bi_1/2TiO₃ (NBT) was investigated from a defect structure viewpoint. To reveal the role of cation vacancies, two series of ceramics, with different cation vacancies, were processed to compensate the excess positive charge of lanthanum ions. In a region of complete solid solution, the grain size of NBLT-B {[(Na_0.5Bi_0.5)_{1− x} La _x ]Ti_{1−0.25 x} O₃} was smaller than that of NBLT-A {[(Na_0.5Bi_0.5)_{1−1.5 x} La _x ]TiO₃} and densification was enhanced more effectively in NBLT-B. With the aid of thermoelectric power, electric conductivity, and electrotransport measurements, it was found that different sintering behaviors between NBLT-A and NBLT-B specimens were related to the change in the type of cation vacancies present and that lanthanum ion–cation vacancy pairs played an important role in reducing the grain growth and enhancing the densification process.     

Contribution of Structure to Temperature Dependence of Resonant Frequency in the (1 −x)La(Zn1/2Ti1/2)O3·xATiO3 (A = Ca, Sr) System

The crystal structure and microwave dielectric properties of the (1 − x ) La(Zn_1/2Ti_1/2)O₃· x SrTiO₃ and (1 − x )La(Zn_1/2Ti_1/2)O₃· x CaTiO₃ system were investigated. X-ray powder diffraction showed that cation ordering disappeared at x > 0.3 for both systems. However, infrared spectra demonstrated that short-range cation ordering could exist at x = 0.4. Permittivity and the temperature coefficient of the resonant frequency (τ_f) of both systems exhibited nonmonotonic variations with composition. Both systems exhibited a τ_f of zero at the same composition of x = 0.5 although the τ_f of SrTiO₃ was about two times larger than that of CaTiO₃. The behavior of the permittivity and τ_f were described by the tilting of oxygen octahedra and cation ordering. The relation between τ_f and cation ordering of La(Zn_1/2Ti_1/2)O₃ was discussed in conjunction with the experimental results on metal halides. It is suggested that cation ordering induced a negative τ_f and suppressed the increase of permittivity for compositions between x = 0 to x = 0.5 for (1 − x )La(Zn_1/2Ti_1/2)O₃· x SrTiO₃ and (1 − x )La(Zn_1/2Ti_1/2)O₃· x CaTiO₃ systems.     

Microwave Dielectric Properties of CaTiO3-CaAl1/2Nb1/2O3 Ceramics Doped with Li3NbO4

The microwave dielectric properties of CaTi_{1− x} (Al_1/2Nb_1/2) _x O₃ solid solutions (0.3 ≤ x ≤ 0.7) have been investigated. The sintered samples had perovskite structures similar to CaTiO₃. The substitution of Ti⁴⁺ by Al³⁺/Nb⁵⁺ improved the quality factor Q of the sintered specimens. A small addition of Li₃NbO₄ (about 1 wt%) was found to be very effective for lowering sintering temperature of ceramics from 1450–1500° to 1300°C. The composition with x = 0.5 sintered at 1300°C for 5 h revealed excellent dielectric properties, namely, a dielectric constant (ɛ_r) of 48, a Q × f value of 32 100 GHz, and a temperature coefficient of the resonant frequency (τ_f) of −2 ppm/K. Li₃NbO₄ as a sintering additive had no harmful influence on τ_f of ceramics.     

BiScO3 Doped (Na0.5K0.5)NbO3 Lead-Free Piezoelectric Ceramics

Lead-free potassium sodium niobate-based piezoelectric ceramics (1− x )(Na_0.5K_0.5)NbO₃– x BiScO₃ (KNN–BS) ( x =0∼0.05) have been prepared by an ordinary sintering process. Single perovskite phase of KNN–BS exhibits an orthorhombic symmetry at x <0.015 and pseudocubic symmetry at x >0.02, separating by a MPB at 0.015≤ x ≤0.02. Piezoelectric and ferroelectric properties are significantly enhanced in the MPB, which are as follows: piezoelectric constant d ₃₃=203 pC/N, planar coupling coefficient k _p=0.36, remnant polarization P _r=24.4 μC/cm². These solid solution ceramics look promising as a potential lead-free candidate materials.     

K/Na Ratio Dependence of the Electrical Properties of [(KxNa1−x)0.95Li0.05](Nb0.95Ta0.05)O3 Lead-Free Ceramics

[(K _x Na_{1− x} )_0.95Li_0.05](Nb_0.95Ta_0.05)O₃ (K _x NLNT) ( x= 0.40–0.60) lead-free piezoelectric ceramics were prepared by conventional solid-state sintering. The effects of K/Na ratio on the dielectric, piezoelectric, and ferroelectric properties of the K _x NLNT ceramics were studied. The experimental results show that the electrical properties strongly depend on the K/Na ratio in the K _x NLNT ceramics. The K _x NLNT ( x =0.42) ceramics exhibit enhanced properties ( d ₃₃∼242 pC/N, k _p∼45.7%, k _t∼47%, T _c∼432°C, T _o−t =48°C, ɛ_r∼1040, tanδ∼2.0%, P _r∼26.4 μC/cm², E _c∼10.3 kV/cm). Enhanced electrical properties of the K _x NLNT ( x =0.42) ceramics could be attributed to the polymorphic phase transition near room temperature. These results show that the K _x NLNT ( x =0.42) ceramic is a promising lead-free piezoelectric material.     

Dislocation Loop Formation in Nonstoichiometric (Ba,Ca)TiO3 and BaTiO3 Ceramics

Dislocation loops observed in nonstoichiometric and stoichiometric (Ba,Ca)TiO₃, and in stoichiometric BaTiO₃ sintered in a reducing atmosphere, were characterized by conventional transmission electron microscopy (TEM) under two-beam conditions and high-resolution TEM atomic structure analysis. Dislocation loops mostly lay on {100} planes with Burgers vectors of type 〈100〉. The dynamic behavior of these dislocation loops during the electron beam irradiation (EBI), however, was classified into two different types of dislocation loops: in A-site-excess (Ba,Ca)TiO₃, contrasts of dislocation loops faded completely away; in BaTiO₃ and B-site-excess (Ba,Ca)TiO₃, fine-line contrasts remained. Dislocation loops with Burgers vectors of type 1/2〈100〉 and the resultant crystallographic shear (CS) structure with a displacement vector of type 1/2〈110〉 after EBI were proposed to interpret residual line images. Disappearance of these line images in A-site-excess (Ba,Ca)TiO₃ strongly suggests preferential Ca ion site occupancy at the CS structure.     

Dislocation-Containing Planar Faults in Metastably Retained Hexagonal Barium Titanate

Planar faults, designated F ₁– F ₆ and F _a , with intermixed dislocations in metastably retained hexagonal-BaTiO₃ ceramics, were found and analyzed by transmission electron microscopy. Only faults with one, two, and four extra c -layers parallel to the basal plane have been identified. Fault vectors R_F1=R_Fa=1/6[02 2 1], R_F2=R_F3=1/3[0 1 11], R_F4=1/3[01 1 2], and R_F'1=R_F5= R_F6=R_F'a=1/6[0 2 21] were determined adopting the 2πg·R=0 (or 2 n π) criteria in combination with high-resolution imaging. Further, the embedded dislocations were half-partials with Burgers vectors b=1/3〈10 1 0〉 determined by the g·b=0 effective invisibility criteria in conjunction with the eligible fault vectors. A rotation by 60° about the c -axis was found between fault segments with R_F1=1/6[02 2 1] and R_F'1=1/6[20 2 1] located on either side of a partial. Basal dislocations with b_B=1/3〈1 2 10〉 have dissociated into two prism-plane Shockley half-partials with b_Pr=1/3〈1 1 00〉 by glide in the fault plane (0002) according to 1/3〈1 2 10〉→1/3〈1 1 00〉+1/3〈0 1 10〉. The fault segment F'₁ encompassed by two half-partials is an extrinsic complex stacking fault.     

Piezoelectric Properties of (1−x)(Na0.5K0.5)NbO3–xAgSbO3 Lead-Free Ceramics

(1− x )(Na_0.5K_0.5)NbO₃– x AgSbO₃ lead-free piezoelectric ceramics were prepared by normal sintering. The effects of the AgSbO₃ on the phase structure and piezoelectric properties of the ceramics were systematically studied. These results show that the AgSbO₃-modified (K_0.50Na_0.50)NbO₃ lead-free piezoelectric ceramics form stable solution with orthorhombic structure, and the Curie temperature and the polymorphic phase transition of the ceramics decreased with increasing AgSbO₃. The result shows that the piezoelectric properties of the ceramics strongly depend on the AgSbO₃. The ceramics with x =0.05 possess optimum properties ( d ₃₃=192 pC/N, k _p=43%, T _c=348°C, T _o−t =145°C, ɛ_r∼632, and tan δ∼3.5%). These results indicate that the ceramic is a promising candidate material for lead-free piezoelectric ceramics.