Thermal studies on fluorite type ZryU1−yO2 solid solutions

Solid state reactions of UO₂ and ZrO₂ in mild oxidizing condition followed by reduction at 1673 K showed enhanced solubility up to 35 mol% of zirconium in UO₂ forming cubic fluorite type Zr_yU_1−yO₂ solid solution. The lattice parameters and O/M (M = U + Zr) ratios of the solid solutions, Zr_yU_1−yO_2+x, prepared in different gas streams were investigated. The lattice parameters of these solid solutions were expressed as a linear equation of x and y: a₀ (nm) = 0.54704 − 0.021x - 0.030y. The oxidation of these solid solutions for 0.1 ? y ? 0.2 resulted in cubic phase MO_2+x up to700 K and single orthorhombic zirconium substituted α-U₃O₈ phase at 1000 K. The kinetics of oxidation of Zr_yU_1−yO₂ in air for y = 0-0.35 were also studied using thermogravimetry. The specific heat capacities of Zr_yU_1−yO₂ (y = 0-0.35) were measured using heat flux differential scanning calorimetry in the temperature range of 334-860 K.     

Oxygen potential and thermal conductivity of (U, Pu) mixed oxides

(U, Pu) mixed oxides, (U_1−yPu_y)O_2−x, with y = 0.21 and 0.28 are being considered as fuels for the Prototype Fast Breeder Reactor (PFBR) in India. The use of urania-plutonia solid solutions in PFBR calls for accurate measurement of physicochemical properties of these materials. Hence, in the present study, oxygen potentials of (U_1−yPu_y)O_2−x, with y = 0.21 and 0.28 were measured over the temperature range 1073-1473 K covering an oxygen potential range of −550 to −300 kJ mol⁻¹ (O/M ratio from 1.96 to 2.000) by employing a H₂/H₂O gas equilibration technique followed by solid electrolyte EMFmeasurement. (U_1−yPu_y)O_2−x, with y = 0.40 is being used in the Fast Breeder Test Reactor (FBTR) in India to test the behaviour of fuels with high plutonium content. However, data on the oxygen potential as well as thermal conductivity of the mixed oxides with high plutonium content are scanty. Hence, the thermal diffusivity of (U_1−yPu_y)O₂, with y = 0.21, 0.28 and 0.40 was measured and the results of the measurements are reported.     

Synthesis, characterization and thermal expansion measurements on uranium-cerium mixed oxides

Uranium-cerium mixed oxides (U_1−yCe_y)O₂ (y = 0.2, 0.4, 0.6, 0.8) were prepared by combustion synthesis using citric acid as the fuel. Sintering of the solid solutions was carried out at 1873 K under reduced atmosphere. From the room temperature XRD patterns of the sintered samples it was found that the solid solutions form single phase fluorite structure. The room temperature lattice parameters of (U_1−yCe_y)O₂ (y = 0.2, 0.4, 0.6, 0.8) are 0.5458, 0.5446, 0.5434 and 0.5422 nm respectively. Thermal expansion of (U_1−yCe_y)O₂ (y = 0.2, 0.4, 0.6, 0.8) in the temperature range 298-1973 K was measured by high temperature X-ray diffraction (HTXRD). The coefficients of thermal expansion increase with increase in CeO₂ content in the sample and the measured data in the temperature range 298-1973 K, for (U_1−yCe_y)O₂ (y = 0.2, 0.4, 0.6, 0.8) are 18.23, 19.91, 21.59, 23.29 × 10⁻⁶ K⁻¹, respectively.     

Thermodynamic investigations of ThO2-UO2 solid solutions

Heat capacities and enthalpy increments of solid solutions Th_1−yU_yO₂(s) (y = 0.0196, 0.0392, 0.0588, 0.098, 0.1964) and Simfuel (y = 0.0196) were measured by using a differential scanning calorimeter and a high temperature drop calorimeter. The heat capacities were measured in two temperature ranges: 127-305 K and 305-845 K and enthalpy increments were determined in the temperature range 891-1698 K. A heat capacity expression as a function of uranium content y and temperature and a set of self-consistent thermodynamic functions for Th_1−yU_yO₂(s) were computed from present work and the literature data. The oxygen potentials of Th_1−yU_yO_2+x(s) have been calculated and expressed as a polynomial functions of uranium content y, excess oxygen x and temperature T. The phase diagram, oxygen potential diagram of thorium-uranium-oxygen system and major vapour species over urania thoria mixed oxide have been computed using FactSage code.     

Determination of mass attenuation coefficients, effective atomic and electron numbers for Cr, Fe and Ni alloys at different energies

The total mass attenuation coefficients (μ_m), for Cr, Fe, Ni and Fe_xNi_1−x (x = 0.8, 0.7, 0.6, 0.5, 0.4, 0.3 and 0.2), Fe_xCr_yNi_1−(x+y) (x = 0.7, y = 0.1; x = 0.5, y = 0.2; x = 0.4, y = 0.3; x = 0.3, y = 0.3; x = 0.2, y = 0.2 and x = 0.1, y = 0.2) and Ni_xCr_1−x (x = 0.8, 0.6, 0.5, 0.4 and 0.2) alloys were measured at 22.1, 25.0, 59.5 and 88.0 keV photon energies. The samples were irradiated with 10 mCi Cd-109 and 100 mCi Am-241 radioactive point source using transmission arrangement. The γ- and X-rays were counted by a Si(Li) detector with a resolution of 160 eV at 5.9 keV. Total atomic and electronic cross-sections (σ_t and σ_e), effective atomic and electron numbers (Z_eff and N_eff) were determined experimentally and theoretically using the obtained mass attenuation coefficients for investigated 3d alloys. The theoretical mass attenuation coefficients of each alloy were estimated using mixture rule. The experimental values were compared with the calculated values for all samples.     

Thermal conductivities of hypostoichiometric (U, Pu, Am)O2−x oxide

The thermal conductivities of (U_0.68Pu_0.30Am_0.02)O_2.00−x solid solutions (x = 0.00-0.08) were studied at temperatures from 900 to 1773 K. The thermal conductivities were obtained from the thermal diffusivities measured by the laser flash method. The thermal conductivities obtained experimentally up to about 1400 K could be expressed by a classical phonon transport model, λ = (A + BT)⁻¹, A(x) = 3.31 × x + 9.92 × 10⁻³ (mK/W) and B(x) = (−6.68 × x + 2.46) × 10⁻⁴ (m/W). The experimental A values showed a good agreement with theoretical predictions, but the experimental B values showed not so good agreement with the theoretical ones in the low O/M ratio region. From the comparison of A and B values obtained in this study with the ones of (U,Pu)O_2−x obtained by Duriez et al. [C. Duriez, J.P. Alessandri, T. Gervais, Y. Philipponneau, J. Nucl. Mater. 277 (2000) 143], the addition of Am into (U, Pu)O_2−x gave no significant effect on the O/M dependency of A and B values.     

Effect of Nd and Pr addition on the thermal and mechanical properties of (U, Ce)O2

The thermal conductivity, Young’s modulus, and hardness of (U_0.65−xCe_0.3Pr_0.05Nd_x)O₂ (x = 0.01, 0.08, 0.12) were evaluated and the effect of Pr and Nd addition on the properties of (U, Ce)O₂ were studied. The polycrystalline high-density pellets were prepared with solid state reactions of UO₂, CeO₂, Pr₂O₃, and Nd₂O₃. We confirmed that all Ce, Pr, and Nd dissolved in UO₂ and formed solid solutions of (U, Ce, Pr, Nd)O₂. We revealed that the thermal conductivity of (U_0.65−xCe_0.3Pr_0.05Nd_x)O₂ (x = 0.12) was up to 25% lower than that of x = 0.01 at room temperature. The Young’s modulus of (U_0.65−xCe_0.3Pr_0.05Nd_x)O₂ decreased with x, whereas the hardness values were constant in the investigated x range.     

Light ion irradiation effects on stuffed Lu2(Ti2−xLux)O7−x/2 (x = 0, 0.4 and 0.67) structures

We have recently synthesized “stuffed” (i.e., excess Lu) Lu₂(Ti_2−xLu_x)O_7−x/2 (x = 0, 0.4 and 0.67) compounds using conventional ceramic processing. X-ray diffraction measurements indicate that stuffing more Lu³⁺ cations into the oxide structure leads eventually to an order-to-disorder (O-D) transition, from an ordered pyrochlore to a disordered fluorite crystal structure. At the maximum deviation in stoichiometry (x = 0.67), the Lu³⁺ and Ti⁴⁺ ions become completely randomized on the cation sublattices, and the oxygen “vacancies” are randomized on the anion sublattice. Samples were irradiated with 400 keV Ne²⁺ ions to fluences ranging from 1 × 10¹⁵ to 1 × 10¹⁶ ions/cm² at cryogenic temperatures (∼77 K). Ion irradiation effects in these samples were examined by using grazing incident X-ray diffraction. The results show that the ion irradiation tolerance increases with disordering extent in the non-stoichiometric Lu₂(Ti_2−xLu_x)O_7−x/2.     

Oxygen potential measurements of Am0.5Pu0.5O2−x by EMF method

The dependence of the oxygen potentials on oxygen non-stoichiometry and temperature of Am_0.5Pu_0.5O_2−x has been obtained by the electromotive force (EMF) method with the cell: (Pt) air |Zr(Ca)O_2−x| Am_0.5Pu_0.5O_2−x (Pt). The x value of Am_0.5Pu_0.5O_2−x was changed at 1333 K over 0.02 < x ? 0.25 by the coulomb titration method. The temperature dependence of the oxygen potential was also measured over the range of 1173-1333 K. It was found that the oxygen potential decreased from −80 to −360 kJ mol⁻¹ with increasing x from 0.021 to 0.22 at 1333 K and that it remained almost constant at −360 kJmol⁻¹ around x = 0.23. It was concluded that Am_0.5Pu_0.5O_2−x should be composed of the single fluorite-type phase over 0.02 < x ? 0.22 and the mixed phases of fluorite-type and (Am, Pu)₉O₁₆ at around x = 0.23.     

Thermal conductivity of (U,Pu,Np)O2 solid solutions

The thermal conductivities of (U_,Pu_,Np)O₂ solid solutions were studied at temperatures from 900 to 1770 K. Thermal conductivities were obtained from the thermal diffusivity measured by the laser flash method. The thermal conductivities obtained below 1400 K were analyzed with the data of (U,Pu,Am)O₂ obtained previously, assuming that the B-value was constant, and could be expressed by a classical phonon transport model, λ = (A + BT)⁻¹, A(z₁, z₂) = 3.583 × 10⁻¹ × z₁ + 6.317 × 10⁻² × z₂ + 1.595 × 10⁻² (m K/W) and B = 2.493 × 10⁻⁴ (m/W), where z₁ and z₂ are the contents of Am- and Np-oxides. It was found that the A-values increased linearly with increasing Np- and Am-oxide contents slightly, and the effect of Np-oxide content on A-values was smaller than that of Am-oxide content. The results obtained from the theoretical calculation based on the classical phonon transport model showed good agreement with the experimental results.     

Solubility of ThO2 in Gd2Zr2O7 pyrochlore: XRD, SEM and Raman spectroscopic studies

Solubility of ThO₂ in gadolinium zirconate pyrochlore, a potential host for radioactive materials, has been investigated. The phase relations in Gd_2−xTh_xZr₂O_7+x/2 (0.0 ? x ? 2.0) systems have been established under the slow-cooled conditions from 1400 °C. XRD studies reveal that the compositions corresponding to x = 0.0-0.075 are single phasic in nature and beyond x ? 0.1 the biphasic region starts. The first biphasic region comprising of pyrochlore and thoria exist from x = 0.1-0.8, and from x = 1.2 another biphasic region consisting of gadolinia stabilized zirconia (GSZ) and thoria appears which persists till x = 1.6. The end member (i.e. x = 2.0) of the series is found to be a mixture of monoclinic ZrO₂ and thoria. Interestingly, gadolinia which has wide solubility in thoria, did not show any miscibility in thoria in the presence of zirconia. Irregular grains of Gd_1.8Th_0.2Zr₂O_7.1 as shown in SEM supports its biphasic nature. Raman spectra of heavily thoria doped (x = 0.1 and 0.2) samples, indicates the presence of Zr-O₇ mode which implies the samples are highly disordered in nature.     

Gamma-ray shielding and structural properties of PbO-SiO2 glasses

Gamma-ray attenuation coefficients have been determined experimentally using a narrow beam transmission method for the xPbO(1−x)SiO₂ (x = 0.45-0.70) glass system at 662, 1173 and 1332 keV photon energies. These values have also been obtained theoretically using the ‘mixture rule’ and the ‘XCOM’ computer software. The results have been used to calculate half value layer parameters. Gamma-ray shielding properties of PbO-SiO₂ glass samples have been compared with standard radiation shielding concretes. The molar volume, FTIR and acoustic investigations have been used to study the structural properties of the prepared glass system.     

Phase relations and linear thermal expansion of cubic solid solutions in the Th1−xMxO2−x/2 (M = Eu, Gd, Dy) systems

Cell parameters and linear thermal expansion studies of the Th-M oxide systems with general compositions Th_1−xM_xO_2−x/2 (M = Eu³⁺, Gd³⁺ and Dy³⁺, 0.0 ? x ? 1.0) are reported. The XRD patterns of each product were refined to specify the solid solubility limits of MO_1.5 in the ThO₂ lattice. The upper solid solubility limits of EuO_1.5, GdO_1.5 and DyO_1.5 in the ThO₂ lattice under conditions of slow cooling from 1673 K are represented as Th_0.50Eu_0.50O_1.75, Th_0.60Gd_0.40O_1.80 and Th_0.85Dy_0.15O_1.925, respectively. The linear thermal expansion (293-1123 K) of MO_1.5 and their single-phase solid solutions with thoria were investigated by dilatometery. The average linear thermal expansion coefficients () of the compounds decrease on going from EuO_1.5 to DyO_1.5. The values of for EuO_1.5, GdO_1.5 and DyO_1.5 containing solid solutions showed a downward trend as a function of the dopant concentration. The linear thermal expansion (293-1473 K) of the solid solutions investigated by high-temperature XRD also showed a similar trend.     

Thermal and mechanical properties of (U,Er)O2

Erbium is considered as a slow burnable poison suitable for use in light water reactors (LWRs). Addition of a small amount of Er₂O₃ to all UO₂ pellets will make it possible to develop super high burnup fuels in Japanese nuclear facilities which are now under the restriction of the upper limit of ²³⁵U enrichment. When utilizing the (U,Er)O₂ fuels, it is very important to understand the thermal and mechanical properties. Here we show the characterization results of (U_1−xEr_x)O₂ (0 ? x ? 0.1). We measured their thermal and mechanical properties and investigated the effect of Er addition on these properties of (U,Er)O₂. All Er completely dissolved in UO₂, and the lattice parameter decreased linearly with the Er content. Both the thermal conductivity and Young’s modulus of (U,Er)O₂ decreased with the Er content. These results would be useful for us in evaluating the performance of the (U,Er)O₂ fuels in LWRs.     

Structural study of Pu1−xAmxO2 (x = 0.2; 0.5; 0.8) obtained by oxalate co-conversion

This study describes the synthesis and the characterisation of Pu_1−xAm_xO₂ (x = 0.2; 0.5; 0.8) mixed oxides obtained by oxalate co-conversion. We studied the self-irradiation effect in these compounds at the structural scale. We determined, for each composition, the initial lattice parameter and the equation describing its variation versus time and displacements per atom. Similarly to other α emitting compounds, it was observed a fast lattice parameter expansion rate, followed by a stabilisation at a maximum value. The observations also showed that the initial expansion rate varies according to the Am content and the maximum value to the Pu content. However, for all compositions, the lattice parameter relative variations are the same.     

Melting behavior of MgO-based inert matrix fuels containing (Pu,Am)O2−x

The melting behavior of MgO-based inert matrix fuels containing (Pu,Am)O_2−x ((Pu,Am)O_2−x-MgO fuels) was experimentally investigated. Heat-treatment tests were carried out at 2173 K, 2373 K and 2573 K each. The fuel melted at about 2573 K in the eutectic reaction of the Pu-Am-Mg-O system. The (Pu,Am)O_2−x grains, MgO grains and pores grew with increasing temperature. In addition, Am-rich oxide phases were formed in the (Pu,Am)O_2−x phase by heat-treatment at high temperatures. The melting behavior was compared with behaviors of PuO_2−x-MgO and AmO_2−x-MgO fuels.     

Influence on the structural characteristic of defect solid solution GdxZr1−xO2−x/2 with 0.18 ? x ? 0.62 under longer term annealing studied by Gd Mössbauer spectroscopy

Three kinds of defect solid solution Gd_xZr_1−xO_2−x/2 with 0.18 ? x ? 0.62, including the three single crystal samples with x = 0.21, 0.26 and 0.30, were investigated by ¹⁵⁵Gd Mössbauer spectroscopy at 12 K. Difference in the structural characteristic under longer term annealing were confirmed by comparing the ¹⁵⁵Gd Mössbauer parameters of the polycrystalline samples sintered one time and twice at 1773 K for 16 h in air, respectively. The results indicated that the polycrystalline samples sintered twice have relatively equilibrated structure by comparing with the three single crystal samples. After being sintered twice, basically the local structure around the Gd³⁺ ions does not change, but the degree of the displacements of the six 48f oxygen ions from positions of cubic symmetry becomes slightly smaller, and distribution of the Gd³⁺ ions in the system becomes more homogeneous.     

Analysis of oxygen potential of (U0.7Pu0.3)O2±x and (U0.8Pu0.2)O2±x based on point defect chemistry

Stoichiometries in (U_0.7Pu_0.3)O_2±x and (U_0.8Pu_0.2)O_2±x were analyzed with the experimental data of oxygen potential based on point defect chemistry. The relationship between the deviation x of stoichiometric composition and the oxygen partial pressure P_O2 was evaluated using a Kröger-Vink diagram. The concentrations of the point defects in uranium and plutonium mixed oxide (MOX) were estimated from the measurement data of oxygen potentials as functions of temperature and P_O2. The analysis results showed that x was proportional to near the stoichiometric region of both (U_0.7Pu_0.3)O_2±x and (U_0.8Pu_0.2)O_2±x, which suggested that intrinsic ionization was the dominant defect. A model to calculate oxygen potential was derived and it represented the experimental data accurately. Further, the model estimated the thermodynamic data, and , of stoichiometric (U_0.7Pu_0.3)O_2.00 and (U_0.8Pu_0.2)O_2.00 as −552.5 kJ·mol⁻¹ and −149.7 J·mol⁻¹, and −674.0 kJ · mol^-1 and −219.4 J · mol⁻¹, respectively.     

Effect of oxygen potential on the sintering behavior of MgO-based heterogeneous fuels containing (Pu, Am)O2−x

The effect of oxygen potential on the sintering behavior of MgO-based heterogeneous fuels containing (Pu, Am)O_2−x was experimentally investigated. Sintering tests in various atmospheres, i.e. air, moisturized 4%H₂-Ar, and 4%H₂-Ar atmosphere, were carried out. The sintering behavior was found to be significantly affected by the oxygen potential in the sintering atmosphere. The sintered density decreased with decreasing oxygen potential. The (Pu, Am)O_2−x phase sintered in a reductive atmosphere had hypostoichiometry. The aggregates of the (Pu, Am)O_2−x phase sintered in the reductive atmosphere grew, in comparison with those in the oxidizing one. The sintering mechanism was discussed in terms of the difference in sintering behavior of (Pu, Am)O_2−x and MgO.     

Oxygen potentials of mixed oxide fuels for fast reactors

Oxygen potentials of homogenous (Pu_0.2U_0.8)O_2−x and (Am_0.02Pu_0.30Np_0.02U_0.66)O_2−x which have been developed as fuels for fast breeder reactors were measured at temperatures of 1473-1623 K by a gas equilibrium method using an (Ar, H₂, H₂O) gas mixture. The measured oxygen potentials of (Pu_0.2U_0.8)O_2−x were about 25 kJ mol⁻¹ lower than those of (Pu_0.3U_0.7)O_2−x measured previously and were consistent with the values calculated by Besmann and Lindemer’s model. The measured oxygen potentials of (Am_0.02Pu_0.30Np_0.02U_0.66)O_2−x were slightly higher than those of MOX without minor actinides. No fuel-cladding chemical interaction is affected significantly by adding their minor actinides.