A Study of the Phase Relations of ZrO2–TiO2 and ZrO2–TiO2–SiO2

The phase relations of the systems ZrO₂–TiO₂ and ZrO₂–TiO₂–SiO₂ were investigated. X-ray diffraction techniques served as the principal means of analysis. The binary system ZrO₂–TiO₂ was found to be one of partial solid solutions with no intermediate compounds. A eutectic point was found to exist at 50 to 55 weight % ZrO₂ and 1600°C. A preliminary investigation of the ternary system ZrO₂–TiO₂–SiO₂, although not extensive, resulted in a better understanding of this system, with a fairly accurate location of some of its boundary lines. A eutectic point was located at 2% ZrO₂, 10% TiO₂, and 88% SiO₂ at approximately 1500°C.     

SiO2–PbO–CaO–ZrO2–TiO2–(B2O3–K2O), A New Zirconolite Glass–Ceramic System: Crystallization Behavior and Microstructure Evaluation

Zirconolite (CaZrTi₂O₇) is a mineral that has a high containment capacity for actinides and lanthanides and is considered to be a good candidate for the immobilization of radioactive wastes. The glass–ceramic technique seems to be a very suitable and convenient method to produce zirconolite crystals by precipitating them in a specific glass matrix. In this study, development of a new zirconolite-based glass–ceramic belonging to SiO₂–PbO–CaO–ZrO₂–TiO₂–(B₂O₃–K₂O) system was investigated. The presence of PbO, together with B₂O₃ and K₂O, allowed the preparation of a X-ray diffraction (XRD) amorphous glass with a relatively high concentration of ZrO₂ and TiO₂, which was successfully converted to a glass–ceramic containing 34 wt% of zirconolite after heating at 770°C for 4 h. Differential thermal analysis, XRD, scanning electron microscope, and energy dispersive X-ray spectroscopy were used to determine the crystallization conditions, identify the crystallized phases, determine their compositions and quantities and observe and analyze the microstructures. The zirconolite crystals showed a platelet morphology with a monoclinic structure characterized by a =1.246 nm, b =0.7193 nm, c =1.128 nm, and β=100.508°.     

Liquid–Solid Equilibria in the System NiO–TiO2–SiO2 in the Temperature Range 1430° to 1660°C

Equilibrium relations in the system NiO–TiO₂–SiO₂ in air have been investigated in the temperature range 1430° to 1660°C. The most conspicuous feature of the phase relations is the existence of a cation-excess spinel-type phase, in addition to NiO and NiTiO₃, on the liquidus surface and at subsolidus temperatures down to 1430°C. Three invariant points have been located on the liquidus. There is a peritectic at 1540°C characterized by coexisting NiO ( ss ), spinel( ss ), cristobalite, and liquid of composition 47 wt% NiO, 29 wt% TiO₂, and 24 wt% SiO₂. Two eutectics are present, one at 1480°C, with spinel( ss ), NiTiO₃, cristobalite, and liquid (42 wt% NiO, 43 wt% TiO₂, and 15 wt% SiO₂), as the coexisting phases. The other is at 1490°C with NiTiO₃, rutile, cristobalite, and liquid (32 wt% NiO, 56 wt% TiO₂, and 12 wt% SiO₂). A liquid miscibility gap extends across the diagram from the two bounding binary systems NiO–SiO₂ and TiO₂–SiO₂.     

Fluoride Model Systems: II, The Binary Systems CaF2–BeF2, MgF2–BeF2, and LiF–MgF2

Data obtained by quenching, thermal, and high-temperature X-ray techniques are presented for the three binary systems CaF₂–BeF₂, MgF₂–BeF₂, and LiF–MgF₂. The systems CaF₂–BeF₂ and MgF₂–BeF₂ are presented as weakened models of the systems ZrO₂–SiO₂ and TiO₂–SiO₂, respectively. The compound CaBeF₄ is a model of ZrSiO₄ (zircon). New data obtained for the system LiF–MgF₂ explain many discrepancies among the results of previous authors. Solid solution is almost complete between LiF and MgF₂ at elevated temperatures, but a small gap occurs at the eutectic (735°C.) with extensive exsolution at lower temperatures.     

Sintering and Crystallization of CaO–Al2O3–ZrO2–SiO2 Glasses Containing Different Amount of Al2O3

In this work several complementary techniques have been employed to carefully characterize the sintering and crystallization behavior of CaO–Al₂O₃–ZrO₂–SiO₂ glass powder compacts after different heat treatments. The research started from a new base glass 33.69 CaO–1.00 Al₂O₃–7.68 ZrO₂–55.43SiO₂ (mol%) to which 5 and 10 mol% Al₂O₃ were added. The glasses with higher amounts of alumina sintered at higher temperatures (953°C [lower amount] vs. 987°C [higher amount]). A combination of the linear shrinkage and viscosity data allowed to easily find the viscosity values corresponding to the beginning and the end of the sintering process. Anorthite and wollastonite crystals formed in the sintered samples, especially at lower temperatures. At higher temperatures, a new crystalline phase containing ZrO₂ (2CaO·4SiO₂·ZrO₂) appeared in all studied specimens.     

Al2O3–ZrO2–SiO2 Ternary Glasses for Molybdenum Oxidation Barriers

The wettability of binary and ternary glasses belonging to SiO₂–Al₂O₃–ZrO₂ diagram has been studied using the sessile drop technique at 1750° and 1800°C. The ternary SiO₂–Al₂O₃–ZrO₂ (90–5–5 wt%) glass has proved to be well appropriated as a molybdenum oxidation barrier coating. The addition of 5 wt% of MoO₂ slightly improves its wettablity at higher temperatures without affecting its oxidation barrier properties. The Mo comes into the glass network as a mixture of Mo⁵⁺, Mo⁴⁺, and Mo⁶⁺. After oxidation at 1000°C in oxygen atmosphere, the molybdenum remains in the glass network as Mo⁶⁺.     

Phase Equilibria in the System CaO-TiO2–SiO2

Results of a study of phase equilibria in the system CaO–TiO₂–SiO₂ are presented. A prominent feature of the liquidus surface is a large two-liquid region which appears on the equilibrium diagram as a broad band extending from the SiO₂-CaO side to the SiO₂-TiO₂ side of the triangle. Evidence for the liquid immiscibility and the significance of the resulting large high-temperature liquidus region in silicate technology are discussed. Representative paths of crystallization of liquids in the system under equilibrium conditions are outlined. It is shown that solid solution in the system is virtually nonexistent except for the small-scale substitution of Ti⁴⁺ for Si⁴⁺ in wollastonite. Indices of refraction of glasses are given. Composition and temperature are listed for the twelve liquidus ternary invariant points.     

Phase Equilibrium in the System PbO-TiO2–ZrO2

Phase equilibrium relations in the system PbO–TiO₂–ZrO₂ were studied by quenching in the range where the PbO content is 50 mole % and more. Isotherms were examined at 1100°, 1200°, and 1300°C and tie lines were determined between the liquid and solid solution in equilibrium. The incongruent melting point of PbZrO₃ was 1570°C and the equilibrium between liquid, PbO-type solid, and PbZrO₃ is peritectic. Pb(Zr,Ti)O₃ solid solutions containing more than 14 mole % PbZrO₃ decomposed to liquid, ZrO₂, and Pb(Zr,Ti)O₃ and the decomposition temperature rises from 1340° to 1570°C with increasing PbZrO₃ content. The system PbTiO₃–PbZrO₃ should not be treated as a binary, but as a section of the ternary system.     

Subsolidus Phase Relationships in the Ga2O3–Al2O3–TiO2 System

Subsolidus phase relationships in the Ga₂O₃–Al₂O₃–TiO₂ system at 1400°C were studied using X-ray diffraction. Phases present in the pseudoternary system include TiO₂ (rutile), Ga_{2−2 x} Al_{2 x} O₃ ( x ≤0.78 β-gallia structure), Al_{2−2 y} Ga_{2 y} O₃ ( y ≤0.12 corundum structure), Ga_{2−2 x} Al_{2 x} TiO₅ (0≤ x ≤1 pseudobrookite structure), and several β-gallia rutile intergrowths that can be expressed as Ga_{4−4 x} Al_{4 x} Ti _{n −4}O_{2 n −2} ( x ≤0.3, 15≤ n ≤33). This study showed no evidence to confirm that aluminum substitution of gallium stabilizes the n =7 β-gallia–rutile intergrowth as has been mentioned in previous work.     

Nanostructure of TiO2 Nano-Coated SiO2 Particles

We characterized SiO₂–TiO₂ nano-hybrid particles, prepared using the sol–gel method, using high-resolution transmission microscopy. A few nanometer-ordered TiO₂ anatase crystallites could be observed on the monodispersed SiO₂ nanoparticle surface. The quantum size effect of the TiO₂ anatase crystallites is attributed to the blue shift of the absorption band. The rough surface of the SiO₂–TiO₂ nano-hybrid particles was derived from the developed growth planes of the TiO₂ anatase crystallites, grown from fully hydrolyzed Ti alkoxide that did not react with acetic acid during the crystallization process at 600°C thermal annealing.     

Influence of TiO2 on Properties of Glasses in the System K2O–PbO–SiO2–TiO2 and Its Relation to Structure

By a progressive weight percent substitution of TiO₂ for SiO₂ at various rations of concentration of K₂O and PbO, the entire region of glass formation in the quaternary system K₂O–PbO–SiO₂–TiO₂ was covered with 51 glass compositions. The properties of these glasses were determined and studied with respect to the role of TiO₂ in the system. The results indicated that the dielectric constant increased progressively with increasing TiO₂ concentration whereas the dissipation factor showed an overall decrease, when measured at 1 Mc and 25°C. Density and the refractive index increased progressively with increasing TiO₂ concentration but deviated from the additive relation. Chemical durability, expansivity, and softening temperature vs. composition curves showed definite inflections. The effect of TiO₂ on oxygen packing indicated that Ti⁴⁺ strengthens the network in lower concentrations and weakens the network in higher concentrations in this system. It appears to be likely that Ti⁴⁺ changes its coordination number form 4 to 6.     

Phase Relationships in the Si3N4–SiO2–Lu2O3 System

Phase relationships in the Si₃N₄–SiO₂–Lu₂O₃ system were investigated at 1850°C in 1 MPa N₂. Only J-phase, Lu₄Si₂O₇N₂ (monoclinic, space group P 2₁/ c , a = 0.74235(8) nm, b = 1.02649(10) nm, c = 1.06595(12) nm, and β= 109.793(6)°) exists as a lutetium silicon oxynitride phase in the Si₃N₄–SiO₂–Lu₂O₃ system. The Si₃N₄/Lu₂O₃ ratio is 1, corresponding to the M-phase composition, resulted in a mixture of Lu–J-phase, β-Si₃N₄, and a new phase of Lu₃Si₅ON₉, having orthorhombic symmetry, space group Pbcm (No. 57), with a = 0.49361(5) nm, b = 1.60622(16) nm, and c = 1.05143(11) nm. The new phase is best represented in the new Si₃N₄–LuN–Lu₂O₃ system. The phase diagram suggests that Lu₄Si₂O₇N₂ is an excellent grain-boundary phase of silicon nitride ceramics for high-temperature applications.     

Studies in Lithium Oxide Systems: VII, Li2O–B2O2–SiO2

Phase relations in the system Li₂O–B₂O₃–SiO₂ were studied by quenching and solid-state reactions. No ternary compounds were detected in the portion of the system containing less than 53% Li₂O. Compatibility triangles were formed from the binary borate and silicate compounds. Liquidus data obtained by quenching are reported for four joins, Li₂O·2SiO₂–Li₂O·2B₂O₃, Li₂O·SiO₂-Li₂O·2B₂O₃, Li₂O·SiO₂-Li₂O·B₂O₃, and Li₂O·2B₂O₃-SiO₂. The last join cuts across the two-liquid region and is not a true binary system. Some probable ternary invariant points were located in the portion of the system which was quenchable to glass and adjacent to the two-liquid region. Further data on the previously reported immiscible liquid formation are given and the significance is discussed. Data on the thermal expansion behavior of certain glasses are presented.     

Degradation of Bioactive Polydimethylsiloxane–CaO–SiO2–TiO2 and Poly(tetramethylene oxide)–CaO–TiO2 Hybrids in a Simulated Body Fluid

It has been shown that polydimethylsiloxane (PDMS)–CaO–SiO₂–TiO₂ and poly(tetramethylene oxide) (PTMO)–CaO–TiO₂ hybrids form apatite on their surfaces in a simulated body fluid (SBF) and show mechanical properties similar to those of human cancellous bones. In the present study, changes, caused by soaking in SBF, were measured in the mechanical properties of PDMS–CaO–SiO₂–TiO₂ hybrids with different CaO and TiO₂ contents and PTMO–CaO–TiO₂ hybrids with different CaO contents. Significant decreases in the strength and strain at failure of the hybrids were observed for the PDMS–CaO–SiO₂–TiO₂ hybrids with high CaO or TiO₂ contents and PTMO–CaO–TiO₂ hybrids with a high CaO content after soaking in SBF for 4 w. This indicates that incorporation of a large amount of CaO component into the hybrids should result in the deterioration of the hybrids in the body environment.     

Sol–Gel Synthesis and Characterization of Ag and Au Nanoparticles in SiO2, TiO2, and ZrO2 Thin Films

Silver and gold nanoparticles were synthesized by the sol–gel process in SiO₂, TiO₂, and ZrO₂ thin films. A versatile method, based on the use of coordination chemistry, is presented for stabilizing Ag⁺ and Au³⁺ ions in sol–gel systems. Various ligands of the metal ions were tested, and for each system it was possible to find a suitable ligand capable of stabilizing the metal ions and preventing gold precipitation onto the film surface. Thin films were prepared by spin-coating onto glass or fused silica substrates and then heat-treated at various temperatures in air or H₂ atmosphere for nucleating the metal nanoparticles. The Ag particle size was about 10 nm after heating the SiO₂ film at 600°C and the TiO₂ and ZrO₂ films at 500°C. After heat treatment at 500°C, the Au particle size was 13 and 17 nm in the TiO₂ and ZrO₂ films, respectively. The films were characterized by UV–vis optical absorption spectroscopy and X-ray diffraction, for studying the nucleation and the growth of the metal nanoparticles. The results are discussed with regard to the embedding matrix, the temperature, and the atmosphere of the heat treatment, and it is concluded that crystallization of TiO₂ and ZrO₂ films may hinder the growth of Ag and Au particles.     

Preparation and Physical Properties of Radiofrequency-Sputtered Amorphous Films in the System AlPO4–TiO2

Amorphous films in the system AlPO₄–TiO₂ were prepared by an rf-sputtering method, and their physical properties, such as density, refractive index, and thermal expansion coefficient, and the infrared absorption spectra were measured. The thermal expansion coefficient increased linearly with increasing TiO₂ content. The results of the molar refractivity and the infrared absorption spectra indicated that the coordination number of titanium ions in these films is higher than that in SiO₂–TiO₂ glasses with a negative thermal expansion, in which Ti⁴⁺ ions are tetrahedrally coordinated. In order to confirm the coordination state of the titanium ions in these amorphous films, titanium K -band emission spectra were obtained by X-ray emission spectroscopy, revealing sixfold coordination. The higher coordination state of Ti⁴⁺ was considered to account for these amorphous films not exhibiting negative thermal expansion, as in the SiO₂–TiO₂ system.     

Oxidation of ZrB2–SiC: Influence of SiC Content on Solid and Liquid Oxide Phase Formation

The effect of SiC concentration on the liquid and solid oxide phases formed during oxidation of ZrB₂–SiC composites is investigated. Oxide-scale features called convection cells are formed from liquid and solid oxide reaction products upon oxidation of the ZrB₂–SiC composites. These convection cells form in the outermost borosilicate oxide film of the oxide scale formed on the ZrB₂–SiC during oxidation at high temperatures (≥1500°C). In this study, three ZrB₂–SiC composites with different amounts of SiC were tested at 1550°C for various durations of time to study the effect of the SiC concentration particularly on the formation of the convection cell features. A calculated ternary phase diagram of a ZrO₂–SiO₂–B₂O₃ (BSZ) system was used for interpretation of the results. The convection cells formed during oxidation were fewer and less uniformly distributed for composites with a higher SiC concentration. This is because the convection cells are formed from ZrO₂ precipitates from a BSZ oxide liquid that forms upon oxidation of the composite at 1550°C. Higher SiC-containing composites will have less dissolved ZrO₂ because they have less B₂O₃, which results in a smaller amount of precipitated ZrO₂ and consequently fewer convection cells.     

Subsolidus Phase Relationships in the System Fe2O3–Al2O3–TiO2 between 1000° and 1300°C

Subsolidus phase equilibria in the system Fe₂O₃–Al₂O₃–TiO₂ were investigated between 1000° and 1300°C. Quenched samples were examined using powder X-ray diffraction and electron probe microanalytical methods. The main features of the phase relations were: (a) the presence of an M₃O₅ solid solution series between end members Fe₂TiO₅ and Al₂TiO₅, (b) a miscibility gap along the Fe₂O₃–Al₂O₃ binary, (c) an α-M₂O₃( ss ) ternary solid-solution region based on mutual solubility between Fe₂O₃, Al₂O₃, and TiO₂, and (d) an extensive three-phase region characterized by the assemblage M₃O₅+α-M₂O₃( ss ) + Cor( ss ). A comparison of results with previously established phase relations for the Fe₂O₃–Al₂O₃–TiO₂ system shows considerable discrepancy.     

Chemical Interactions Promoting the ZrO2 Tetragonal Stabilization in ZrO2–SiO2 Binary Oxides

Metastable tetragonal ZrO₂ phase has been observed in ZrO₂–SiO₂ binary oxides prepared by the sol–gel method. There are many studies concerning the causes of ZrO₂ tetragonal stabilization in binary oxides such as Y₃O₂–ZrO₂, MgO–ZrO₂, or CaO–ZrO₂. In these binary oxides, oxygen vacancies cause changes or defects in the ZrO₂ lattice parameters, which are responsible for tetragonal stabilization. Since oxygen vacancies are not expected in ZrO₂–SiO₂ binary oxides, tetragonal stabilization should just be due to the difficulty of zirconia particles growing in the silica matrix. Furthermore, changes in the tetragonal ZrO₂ crystalline lattice parameters of these binary oxides have recently been reported in a previous paper. The changes of the zirconia crystalline lattice parameters must result from the chemical interactions at the silica–zirconia interface (e.g., formation of Si–O–Zr bonds or Si–O⁻ groups). In this paper, FT-IR and ²⁹Si NMR spectroscopy have been used to elucidate whether the presence of Si–O–Zr or Si–O⁻ is responsible for tetragonal phase stabilization. Moreover, X-ray diffraction, Raman spectroscopy, and transmission electron microscopy have also been used to study the crystalline characteristics of the samples.     

Energetics of La2O3–HfO2–SiO2 Glasses

A series of La₂O₃–HfO₂–SiO₂ glasses, approximately along the join 0.73SiO₂–0.27( x HfO₂–(1− x )La₂O₃), 0< x <0.3), was prepared using containerless processing techniques (aerodynamic levitation combined with laser heating in oxygen). The enthalpy of formation and enthalpy of vitrification at 25°C were obtained from drop solution calorimetry of these glasses and appropriate crystalline compounds in a molten lead borate (2PbO–B₂O₃) solvent at 702°C. The enthalpy of formation from crystalline oxides was exothermic and became less exothermic with increasing HfO₂ content. Heat contents were measured by transposed temperature drop calorimetry and depended linearly on the HfO₂ content. Differential scanning calorimetry showed that both the onset glass transition and the onset crystallization temperature of these glasses increased with increasing HfO₂ content. Upon slow cooling in air, the glasses crystallized to a mixture of baddeleyite, cristobalite, lanthanum disilicate, and hafnon.