正丁醇-水-醋酸丁酯三元物系液-液平衡数据的测定、关联和预测

测定了由正丁醇、水和醋酸丁酯形成的三元物系及部分互溶二元物系在20℃、30℃和40℃的LLE(液液平衡)数据,并与文献中已有的正丁醇-水的LLE实测数据核对,说明了测定方法的可靠性.用NRTL和UNIQUAC方程分别进行了三元和二元LLE数据的关联和预测.根据溶液热力学特性对二元LLE模型参数进行了鉴别.在三元LLE数据的关联中,对两种目标函数(摩尔分数和分配系数)进行了比较,并对前一种目标函数中的权重取值问题进行了考察.通过对部分互溶二元物系参数的评选,提高了利用二元参数对三元物系进行预测的准确度.     

含辛烯醛体系的液液、汽液相平衡研究

测定了水-辛烯醛、水-正丁醇二元系在常压下的液液平衡数据及26.66kPa下的正丁醇-辛烯醛二元系和水-正丁醇-辛烯醛三元系的汽液平衡数据.由测定的3对二元数据求取了NRTL常数及有规参数,并与三元数据进行拟合,计算值与实验值符台良好,液液平衡与汽液平衡得到了统一的关联.     

甲醇-甲基丙烯酸甲酯-水三元系汽液平衡和液液汽平衡的研究(Ⅱ)三元系部分

本工作测定了25、35、45、55和60℃时甲醇-甲基丙烯酸甲酯-水三元系互溶区蒸汽压以及部分互溶区的液液平衡和蒸汽压数据.用各对二元系修正的UNIQUAC模型参数推算得到的三元系相平衡数据与实验值符合良好,表明这些模型参数可作为对该三元系进行由低压至常压的相平衡计算基础数据.     

DETERMINATION,CORRELATION AND PREDICTION OF LIQUID-LIQUID EQUILIBRIUM DATA OF n-BUTYL ALCOHOL-WATER-BUTYL ACETATE TERNARY SYSTEM

Liquid-liquid equilibrium(LLE)data have been determined for the n-butyl alcohol-water-butyl acetateternary system and the related binary systems at 293.15,303.15 and 313.15 K.The experimentally determinedLLE data for the n-butyl alcohol-water binary system have been found to be in satisfactory agreementwith the available literature data.The correlation and prediction of the LLE data have been done byusing NRTL and UNIQUAC models.The model parameters of binary systems have been identified witha thermodynamic criterion.In the correlation of ternary LLE data,two objective functions(mole fractionand distribution constant)have been used for purpose of comparison.The effect of weighting in the firstobjective function has been examined.In predicting the ternary LLE with different sets of parameter valuesobtained for each of the constitutent binary systems,improved prediction results have been obtained bycomparing the results of different combinations of the sets of parameter values and choosing those givingthe best result.     

Competitive Adsorption of Basic Dyes onto Calcite in Single and Binary Component Systems

Equilibrium and kinetic behavior of two basic dyes, Methylene Blue (MB) and Safranine T (ST), onto calcite in single and binary component systems have been studied. Experimental equilibrium results have been well predicted by the Freundlich and the Langmuir isotherm models. The model parameters obtained for single solute systems at 298 K have been used for the calculation of adsorption isotherms in binary dye solutions using multi-component isotherm models. Extended Freundlich and extended Langmuir models satisfactorily fit to MB–ST adsorption in binary solutions. A site distribution function which gives information about the affinity of adsorption sites for competing species in a binary system has been mathematically calculated by using Freundlich isotherm parameters. Time-dependent results for single and binary dye solutions have been analyzed according to the Vermeulen and McKay models based on homogeneous and heterogeneous diffusion processes, respectively. Thermodynamic functions for the transition state have been evaluated from the temperature dependence of diffusion coefficients using the Eyring equation.     

Modeling high pressure vapor–liquid equilibrium of ternary systems containing supercritical CO2 and mixed organic solvents using Peng–Robinson equation of state

High pressure vapor–liquid equilibrium (VLE) of CO₂-expanded organic solvents was investigated using Peng–Robinson-LCVM-UNIFAC equation of state. Bubble pressure of several ternary mixtures was predicted using this model and correlations were developed based only on binary experimental data. A sensitivity study of the LCVM parameter numerical value was done by considering the coherence between the mathematical features of the mixing rule and the quality of the simulation. The results provided by PR-LCVM-UNIFAC were compared with those ones given by Peng–Robinson equation of state using the classical quadratic mixing rules (PR-CMR). Despite the use of two adjustable parameters for each binary system, PR-CMR is not able to provide good results when applied to ternary systems. The capability of PR-LCVM-UNIFAC model to predict liquid mixture density for ternary systems using parameters regressed only from bubble pressure experimental data was also investigated. Due to the lack of liquid density experimental data, it was possible to perform only a qualitative assessment of the density curves calculated by this equation of state.     

苯、甲苯和对二甲苯二元和三元系的汽液平衡

本文在改进的Dvorak-Boublik平衡釜中测定了101.33kPa下的苯、甲苯和对二甲苯三组二元系和一组三元系的汽液平衡(VLE)数据。对二元的实验数据作了热力学一致性检验和Wilson方程关联,又由回归二元数据得到的Wilson方程参数推算了三元VLE数据,并将其与测定的数据作了比较,两者符合得较好。     

二甲基硫醚-二硫化碳-甲醇体系等压汽液平衡

用泵式沸点仪测定了100 kPa下二甲基硫醚-二硫化碳、二甲基硫醚-甲醇2个二元系以及二甲基硫醚-二硫化碳-甲醇三元系在不同液相组成时的汽液平衡数据,用Wilson、NRTL、Margules和van Laar模型分别对2个二元系活度系数进行关联,用最小二乘法求出其液相活度系数模型参数,用这些模型参数来计算其汽相组成y,根据过量Gibbs自由能函数Q(GE/RT),采用间接法由Tpx推算了2个二元系的汽相平衡组成。用所得的液相活度系数计算2个二元系的过量吉布斯自由能函数GE/RT,并由2个二元系与三元系回归出二硫化碳-甲醇二元系的NRTL模型参数。用3个二元系NRTL模型参数对所测的三元系数据进行关联,建立三元系汽液平衡的热力学模型并计算平衡时的汽相组成y和泡点温度。分别由Herington法和McDermott-Ellis法对2个二元系和三元系进行热力学一致性检验,结果表明这些相平衡数据满足热力学一致性。     

甲酸-水-甲酸丁酯体系的等压汽液相平衡研究

用改进的Rose釜测定了101.33 kPa下甲酸-水、甲酸-甲酸丁酯、甲酸-水-甲酸丁酯(互溶区内)的等压汽液相平衡数据。考虑了甲酸在汽相中的缔合效应和非理想性,用Hayden-O’connell关联式修正了汽相的非理想性,用NRTL模型对甲酸-水和甲酸-甲酸丁酯体系的汽液平衡数据进行了关联,得到了相应的模型参数。利用得到的二元体系模型参数,结合部分三元体系汽液平衡数据,关联得到水-甲酸丁酯体系的模型参数。由关联得到的3对二元NRTL模型参数预测三元体系汽液平衡数据,温度平均偏差为1.20℃,甲酸的汽相平均偏差为0.0152,甲酸丁酯的汽相平均偏差为0.0184,实验值与预测值基本吻合。     

Predicting the solubility of 1,1-difluoroethane in polystyrene using the perturbed soft chain theory

In this study, the solubility of 1,1-difluoroethane in polystyrene is correlated and predicted using the perturbed soft chain theory (PSCT) and compared with the experimental data in the literature. For correlation, a binary interaction parameter is determined using the experimental solubility data. For prediction, however, the data at infinitely dilute solvent concentration region from inverse gas chromatography (IGC) are used only in determination of the binary interaction parameter. The results were comparable with the experimental data in both cases. © 1998 SCI.     

A generalized correlation for the prediction of phase behaviour in supercritical systems

A generalized two parameter model is presented which uses molecular properties of pure fluids to predict interaction parameters in the attractive term of the Peng-Robinson equation of state. The predictive method is based on a consideration of London (dispersive) forces and includes attractive forces between polar and non-polar molecules that result from induction. Polar-polar effects and quantum forces are omitted. A large body of experimental vapor-liquid equilibrium data measured at near and supercritical conditions (that excludes quantum components and polar-polar systems) was used to calibrate the generalized model. Overall bubble point pressure deviations calculated using the proposed generalization were 5.66% for 3240 data points which compares to average deviations of 3.27% obtained by using regressed binary interaction parameters. Average vapor mole fraction deviations were just under 0.01 using both the generalized and the regressed interaction parameters. The sensitivity of predicted phase envelopes to dispersive and inductive term in the generalized correlation is shown graphically for several systems. Comparisons are also made to another recent interaction parameter generalization presented by Nishiumi et al. (1988).     

The vapour-liquid equilibrium of ternary systems with limited miscibility at atmospheric pressure

The complete study of the vapour-liquid equilibrium of ternary systems with limited miscibility requires vapour-liquid equilibrium determinations and liquid-liquid equilibrium determinations at boiling point. The vapour-liquid equilibrium was determined by means of an equilibrium still based on the principle of Giilespie but modified in such a way that an accurate boiling point measurement, even for systems with heterogeneous liquid was possible and that the vapour phase was analysed without previous condensation. Two ternary systems have been studied: the system methanol-ethylacetate-water and the system ethanol-ethylacetate-water. The ternary data have been predicted by means of the equation of Renon and Prausnitz. The parameters are determined by correlating the binary data. The ternary vapour-liquid equilibrium are predicted within 1-2. 10 ^?2 mol fraction for the vapour composition and 1°C for the boiling point. The position of the predicted tielines of the liquid-liquid equilibrium at boiling point was almost coinciding with the position of the experimental tielines. There was a slight deviation of the predicted and experimental binodal.     

Measurement and correlation of excess enthalpies for water+ethanol+1-buthyl 3-methylimidaozolium tetrafluoroborate system

It is difficult to find physical properties data for systems containing ionic liquids, excess molar enthalpies, binary interaction parameter, etc. In this study, the excess molar enthalpies were measured for water+ethanol+ionic liquid system using a isothermal microcalorimeter at 298.15 K. The ionic liquid used was 1-butyl 3-methyl imidazolium tetrafluoroborate, [BMIM] [BF₄]. The isothermal microcalorimeter (IMC) is a flow-type calorimeter that measures the heat of mixing directly, using specific mixing cell. By employing NRTL, electrolyte-NRTL and UNIQUAC models, binary interaction parameters were determined and investigated for the correlation with vapor liquid equilibrium (VLE). The e-NRTL model with the partial dissociation was employed to correlate the ionic liquid system. The binary data of VLE system were used from literatures. Specifically, UNIQUAC volume and surface area parameters were determined using Bondi radius.     

Densities and excess volumes of aqueous monoethanolamine and diisopropanolamine systems at atmospheric pressure from 303.15 K to 333.15 K

The densities of water+monoethanolamine (MEA), water+diisopropanolamine (DIPA), DIPA+MEA binary systems and water+DIPA+MEA ternary system were measured over the full range of composition at temperatures from 303.15 K to 333.15 K by using an Anton Paar digital vibrating tube density meter (DMA4500). The experimental excess volumes were obtained from the experimental density results and fitted using the Redlich-Kister-Muggianu expression. The parameters obtained from the binary excess volume data were used for the correlation of ternary system with one additional ternary parameter for each isotherm. All investigated binary and ternary systems are completely miscible, because the values of excess volume are negative under the examined conditions.     

Measurement of excess enthalpies using a high-pressure flow microcalorimeter and determination of binary interaction parameters for thermodynamic models

While an equation of state (EOS) plays a critical role in estimating thermodynamic properties, employing it in the determination of binary interaction parameters is extremely important. In general, these parameters can be determined from phase equilibrium data. However, data collection from experiments is a time-consuming and tedious process. In this study, after measuring the excess enthalpies of binary systems containing CO₂ by high-pressure flow isothermal microcalorimetry (IMC), we determined the EOS binary interaction parameters, specifically, the Peng-Robinson EOS binary interaction parameters. These binary interaction parameters obtained by IMC were compared with those obtained by vapor-liquid equilibrium (VLE) experiments. Hence, high-pressure flow IMC appears to be an effective method for the determination of interaction parameters that are used in the estimation of thermodynamic properties. Further, the Flory-Huggins interaction parameters of a binary mixture CO₂ containing with various mole compositions were also estimated by employing high-pressure IMC.     

On the predictive capabilities of CPA for applications in the chemical industry: Multicomponent mixtures containing methyl-methacrylate,dimethyl-ether or acetic acid

The predictive performance of the CPA (Cubic-Plus-Association) equation of state for applications relevant to the chemical industry is illustrated in this work. Three such applications inspired by industrial requests/interest are illustrated here, all of which involve aqueous multicomponent mixtures exhibiting vapor–liquid (VLE) and/or liquid–liquid (LLE) equilibrium. The first two cases include mixtures of methyl-methacrylate with acetone or methanol and dimethyl-ether with ethanol, respectively. In these two cases, the classical form of CPA is used. The third case involves aqueous mixtures with acetic acid, esters, ethers and alcohols, and in this case for water–acetic acid the CPA-Huron Vidal (CPA-HV) version of the model is used. For the latter binary mixture, new CPA-HV binary parameter sets are estimated using, among others, data for activity coefficients at infinite dilutions. The modeling approach is similar in all three cases, i.e. the binary parameters are solely fitted to binary data and thus all multicomponent calculations are considered predictions.It is shown that CPA correlations for binary systems are excellent in all cases using temperature independent parameters except for the acetic acid–water system for which different parameter sets at different temperatures can be recommended. Even with the use of CPA-HV mixing rules, modeling of the acetic acid–water system with few interaction parameters remains a challenging task. Excellent simultaneous VLE and LLE correlation is obtained for complex systems such as aqueous mixtures with ethers and esters. The multicomponent results are, with a few exceptions, very satisfactory, especially for the vapor–liquid equilibrium cases. For the demanding aqueous acetic acid–water containing systems, one parameter set is recommended at the end for modeling ternary or multicomponent mixtures containing acetic acid and water.     

Effect of kinetic models on hot spot temperature prediction for phthalic anhydride production in a multitubular packed bed reactor

Although there are several kinetic models for the production of phthalic anhydride from the partial oxidation of o‐xylene, only few studies have compared the effect of the kinetic model on the prediction of the hot‐spot temperature. In this work, the predicted temperature profile for the partial oxidation of o‐xylene to phthalic anhydride in a multitubular packed bed reactor was obtained for different kinetic mechanisms using one‐dimensional pseudo‐homogeneous and heterogeneous models. The predicted temperature profile using the one‐dimensional heterogeneous model with the kinetic model of Calderbank et al. but with the adjusted kinetic and transport parameters proposed by Anastasov presented a good correlation with regard to experimental data. Nevertheless, in the hot‐spot zone deviations, up to 30 K were presented. In conclusion, the temperature performance in the production of phthalic anhydride is suitably predicted by the one‐dimensional heterogeneous model and the Calderbank et al.'s kinetic model. Though, prediction using bidimensional models should be done to establish the best correlation with experimental data.     

非电解质液体混合物表面张力的统计热力学模型

运用Davis模型导出一个统计热力学的表面张力模型．对22个双组分体系的表面张力作了推算和关联,总平均相对偏差分别为5.45％和1.95％.并利用关联双组分体系得到的参数值,直接推测了三组分体系的表面张力,平均相对偏差为2.21％.结果令人满意.表明该方法简单、精确,便于工程应用．     

含盐多元体系汽液相平衡数据测定及预测

对甲醇／乙醇/水／NH_4NO_3四元体系中的有关含盐二元汽液相平衡数据进行了测定及关联．提出用化学滴定──色谱分析联合法确定含盐液相组成．关联所得的最佳参数用于该体系三元及四元汽液相平衡数据的预测,并与实验值作了比较．结果表明,预测值与实验值符合良好．