Single-laboratory validation of a saponification method for the determination of four polycyclic aromatic hydrocarbons in edible oils by HPLC-fluorescence detection

An analytical method is reported for the determination of four polycyclic aromatic hydrocarbons (benzo[a]pyrene (BaP), benz[a]anthracene (BaA), benzo[b]fluoranthene (BbF) and chrysene (CHR)) in edible oils (sesame, maize, sunflower and olive oil) by high-performance liquid chromatography. Sample preparation is based on three steps including saponification, liquid–liquid partitioning and, finally, clean-up by solid phase extraction on 2 g of silica. Guidance on single-laboratory validation of the proposed analysis method was taken from the second edition of the Eurachem guide on method validation. The lower level of the working range of the method was determined by the limits of quantification of the individual analytes, and the upper level was equal to 5.0 µg kg^?1. The limits of detection and quantification of the four PAHs ranged from 0.06 to 0.12 µg kg^?1 and from 0.13 to 0.24 µg kg^?1. Recoveries of more than 84.8% were achieved for all four PAHs at two concentration levels (2.5 and 5.0 µg kg^?1), and expanded relative measurement uncertainties were below 20%. The performance of the validated method was in all aspects compliant with provisions set in European Union legislation for the performance of analytical methods employed in the official control of food. The applicability of the method to routine samples was evaluated based on a limited number of commercial edible oil samples.     

Levels of benzo[a]pyrene and benzo[a]anthracene in smoked “Provola” cheese from Calabria (Italy)

Levels of benzo[a]pyrene (BaP) and benzo[a]anthracene (BaA) in “Provola” cheese samples from Calabria, smoked naturally and using commercial smoke-flavouring, have been determined. A comparative study of BaP and BaA concentrations was carried out on rind, exterior zone, core and slice of these samples. Quantitative determination of BaP and BaA was ascertained by HPLC using fluorescence detection. Levels of BaP and BaA were found in all smoked “Provola” cheese samples, but higher in cheese smoked with natural methods (0.46–1.13 µg kg^?1 for BaP and 1.38–9.29 µg kg^?1 for BaA) compared to samples smoked using commercial flavouring (0.085–0.32 µg kg^?1 for BaP and 1.20–2.98 µg kg^?1 for BaA). The smoking process contributes to polycyclic aromatic hydrocarbons contamination; however, for improved food safety, the use of commercial buffered smoke is preferable to traditional smoking procedures.     

Polycyclic aromatic hydrocarbons in milk powders marketed in Argentina and Brazil

The aim of this study was to quantify polycyclic aromatic hydrocarbon (PAH) levels in milk powder samples commercialised in Argentina and Brazil during 2012. Thirty-one samples were available from the retail market. An HPLC method for the determination of PAHs was applied involving a clean-up step with silica cartridges. Recoveries were greater than 79% for all PAHs analysed. Reproducible determination with adequate detection and quantification limits (LOD and LOQ) were attained by HPLC with fluorescence detection for 14 PAHs. Acenaphthylene was determined with a UV–VIS detector. There is no significant difference in any PAHs or in the sum of them between the Argentinean and Brazilian samples. Therefore, the samples were evaluated together. The highest concentration of benzo(a)pyrene (BaP) detected was 0.57 µg kg^?1 in milk powder. Contamination of samples expressed as the sum of 15 analysed PAHs varied between 11.8 and 78.4 µg kg^?1 and as PAH4 (BaP, chrysene, benzo(a)anthracene and benzo(b)fluoranthene) was between 0.02 and 10.16 µg kg^?1. The correlation coefficient for PAH2 (BaP and chrysene) and PAH4 groups was 0.95, for PAH2 and PAH8 it was 0.71, and for PAH4 and PAH8 it was 0.83. All the samples were below the regulatory limit for BaP, but 65% of commercial milk powders do not comply with the European Union limit for PAH4. This is the first report of PAH contamination in powder milk from Argentina and Brazil.     

Concentrations and health hazards of polycyclic aromatic hydrocarbons in selected commercial brands of milk

The concentrations and profiles of polycyclic aromatic hydrocarbons (PAHs) were determined in twenty popular commercial brands of milk in the Nigerian market after saponification with ethanolic KOH and cyclohexane extraction and clean up using a gas chromatography with flame ionization detection. The concentrations of the Σ16 PAHs in these brands of milk ranged from 15.6 to 1,711.8 μg kg^?1. The dominant PAH compounds in these brands of milk were 3-and-4-rings PAHs. The dietary intake of BaP, PAH2, PAH4 and PAH8 were 0–53.9 and 0–369.6 ng kg^?1 bw day^?1 respectively. Using these indicators for occurrence and effects (BaP, PAH2, PAH4 and PAH8) PAHs in food, the margin of exposure were <10,000 in 15–30 % of the brands.     

Effect of fuel and kiln type on the polycyclic aromatic hydrocarbon (PAH) levels in smoked shrimp,a Beninese food condiment

Smoked shrimp is a food condiment widely used in Beninese local cooking practices. A previous study revealed that this product is highly contaminated with polycyclic aromatic hydrocarbons (PAH). The present study explored possibilities to reduce PAH levels in shrimp smoked using cottage industry smoking techniques with barrel and chorkor kilns, by replacing wood by charcoal from Acacia auriculiformis and Mangifera indica, as fuels. Results showed that only shrimp smoked using acacia charcoal in a chorkor kiln had PAH levels (benzo[a]pyrene = 5 µg kg^?1 and sum of benzo[a]pyrene, chrysene, benzo[a]anthracene and benzo[b]fluoranthene = 28 µg kg^?1) in accordance with a European standard of 5 and 30 µg kg^?1, respectively, and suitable physicochemical characteristics for good storage (moisture content = 11.9% ± 1.5%; water activity = 0.46 ± 0.03). However, further investigations still needs to be done to reduce the duration of product contact with combustion gasses in order to reduce the PAH content of smoked shrimp to safer levels, largely below standards.     

Polycyclic aromatic hydrocarbons (PAHs) in yerba mate (Ilex paraguariensis) from the Argentinean market

Polycyclic aromatic hydrocarbons (PAHs) occurrence in 50 samples marketed in the main supermarkets from Argentina was surveyed. A high performance liquid chromatography (HPLC) method was applied with fluorescence detection (FLD) and UV—VIS diodes array detector (DAD) for the analysis of 16 PAHs in “yerba mate” (Ilex paraguariensis), with recoveries higher than 89% and limits of detection and quantification lower than that found by other methodologies in previous studies. Contamination expressed as the sum of 16 analysed PAHs ranged between 224.6 and 4449.5 μg kg^?1 on dry mass. The contamination expressed as PAH4 (sum of benzo(a)pyrene, chrysene, benzo(a)anthracene and benzo(b)fluoranthene) varied between 8.3 and 512.4 μg kg^?1. The correlation coefficient for PAH2 (sum of benzo(a)pyrene and chrysene) and PAH4 groups was 0.99, for PAH2 and PAH8 (sum of benzo(a)pyrene, chrysene, benzo(a)anthracene, benzo(b)fluoranthene, benzo(k)fluoranthene, benzo(g,h,i)perylene, dibenzo(a,h)anthracene and indeno(1,2,3cd) pyrene) 0.97 and for PAH4 and PAH8 0.98.     

Determination of Polycyclic Aromatic Hydrocarbons (PAH4) in the Traditional Lebanese Grilled Chicken: Implementation of New,Rapid and Economic Analysis Method

Polycyclic aromatic hydrocarbons (PAH4) (benzo[a]anthracene, chrysene, benzo[b]fluoranthene, and benzo[a]pyrene) are evaluated in a traditional and widely consumed staple in Lebanon “Lebanese Grilled Chicken.” Forty samples with different local additives grilled by charcoal were purchased from different restaurants located in different regions in Lebanon. For this purpose, a simple and a reliable analytical method based on sonication technique and gas chromatography coupled to mass spectrometer (GC-MS) has been developed and validated. Several parameters affecting the extraction efficiency, such as the nature and the volume of the extract solvent, as well as other factors were investigated and optimized. The developed method is environmentally and economically friendly with a minimized consuming time, consisting of a single sonication step for 15 min using 12 mL of non-carcinogenic solvent acetonitrile (ACN) and without any further concentration prior to analysis. Following extraction, the cleanup step was based on freezing and d-SPE by C18 addition. Under optimized conditions, the method performances were evaluated; the limits of quantification (LOQs) achieved were lower than 0.689 μg kg^?1, and these values fit the performance criteria for the method given by the EC that defined the LOQ values of PAH lower than 0.9 μg kg^?1. In addition, the recovery values of the analyzed PAHs ranged from 88.9 to 119.3% with relative standard deviations (RSDs) less than 8% (n = 15). The levels of PAH4 were in the range from 1.52 to 49.9 μg kg^?1, where about 40% of the Lebanese grilled chicken exceeded the EU commission MRLs of 12 μg kg^?1.     

Survey of polycyclic aromatic hydrocarbons of vegetable oils and oilseeds by GC-MS in China

There is a lack of information regarding the occurrence and content of contamination of polycyclic aromatic hydrocarbon (PAH) in edible vegetable oils and oilseeds used for oil production in China. By combining the advantages of ultrasound-assisted extraction, low temperature separation and silica SPE purification, a method for the determination of the USEPA, 16 PAHs was developed based on GC-MS to fill this gap. The method recoveries for oils and oilseeds were 84.4–113.8% and 84.3–115.3%, respectively. The LODs and LOQs for 16 PAHs were ranged from 0.06–0.17 and 0.19–0.56 μg kg^–1, respectively. Based on the established method, PAH concentrations in 21 edible oils and 17 oilseeds were determined. Almost all the PAHs were found in all the samples tested, especially the light PAHs (LPAHs). Three oil samples exceeded the maximum level of 10 μg kg^–1 for BaP set by China. However, five and six oil samples, respectively, exceeded the maximum limits of 2 and 10 μg kg^–1 set for BaP and PAH4 by the European Union. The concentrations of PAH16 in oilseed samples were 1.5 times higher than corresponding oil samples. The relationships between PAH4 and PAH8, PAH4 and PAH16 as well as PAH8 and PAH16 indicates that PAH4 is a sufficient surrogate for the contamination level of PAHs in edible oils when compared with PAH8.     

Polycyclic aromatic hydrocarbons in Italian preserved food products in oil

A method based on gas chromatography/ tandem mass spectrometry was used to assess levels of 16 EU priority polycyclic aromatic hydrocarbons (PAHs) in 48 preserved food products in oil including foods such as vegetables in oil, fish in oil and oil-based sauces obtained from the Italian market. The benzo[a]pyrene concentrations ranged from <0.04 to 0.40 µg kg^?1, and 72.9% of the samples showed detectable levels of this compound. The highest contamination level was observed for chrysene with three additional PAHs (benzo[a]anthracene, benzo[b]fluoranthene and benzo[c]fluorene) giving mean values higher than the mean value for benzo[a]pyrene. Chrysene was detected in all the samples at concentrations ranging from 0.07 to 1.80 µg kg^?1 (median 0.31 µg kg^?1). The contamination expressed as PAH4 (sum of benzo(a)pyrene, chrysene, benzo(a)anthracene and benzo(b)fluoranthene), for which the maximum tolerable limit has been set by Commission Regulation (EU) No. 835/2011, varied between 0.10 and 2.94 µg kg^?1.     

Rapid and sensitive method for the determination of four EU marker polycyclic aromatic hydrocarbons in cereal-based foods using isotope-dilution GC/MS

A rapid and sensitive method has been developed for the determination of the four European Union marker polycyclic aromatic hydrocarbons (PAHs; benz[a]anthracene, chrysene, benzo[b]fluoranthene and benzo[a]pyrene) in some cereal-based foods. The method is based on pressurised liquid extraction (PLE), solid-phase extraction clean-up (SPE) and isotope-dilution gas chromatography with mass-spectrometric detection (GC/MS). The developed method was calibrated for the content range of 0.05–12.5 µg kg^?1 (expressed on a product basis). Recoveries of PAH were monitored in each sample via the recovery of ¹³C-labelled PAHs. Recovery values were in the range between 86% and 91%, with relative standard deviations (RSDs) between 5% and 9%. The achieved limits of detection for all analytes were below 0.05 µg kg^?1. The applicability of the method for the analysis of routine samples was studied by the analysis of a set of commercial bread and breakfast cereal samples. In all analysed samples, benzo[a]pyrene (BAP) was the most prevalent PAH with the content between 0.09 and 0.30 µg kg^?1. On average, samples showed low levels of the sum of the four EU marker PAHs (ΣPAH4) that ranged between 0.11 and 0.22 µg kg^?1 for bread samples and between 0.23 and 0.87 µg kg^?1 for breakfast cereal samples. The developed method was found suitable for the determination of PAHs in cereal-based foods like cornflakes and breads with total relative fat contents below 3.5%.     

Benzo(a)pyrene penetration on a smoked meat product during smoking time

The Codex Alimentarius gives recommendations to prevent carcinogenic polycyclic aromatic hydrocarbons (PAH) (represented by benzo(a)pyrene (BaP)) contamination during processing of meat products, including the control of smoking time. The influence of direct smoking time (0, 1, 3, 5 and 7 days) on the relationship between the BaP and moisture content of a typical Spanish smoked meat product called chorizo and the mechanism of BaP penetration and water release from four different depths in the product was studied. Chorizo was studied from the Principality of Asturias, a location never before tested. An analytical method was developed for this purpose consisting of PAH extraction assisted by sonication followed by solid-phase extraction (SPE) sample clean-up and analytical determination using GC-MS. Results show that an increase in smoking time produced contradictory and independent effects on the moisture and BaP content (µg kg^–1) of chorizos. The moisture content decreased from 49.9% to 31.3%. On the other hand, the BaP content increased from less than 0.24 µg kg^–1 to 0.75 µg kg^–1, finally stabilising after 5 days of smoking. After this time, the natural pores of the casing could be blocked by the large size tar particles from smoke, preventing the continued penetration of PAHs. The BaP content decreased and the moisture content increased progressively from the casing to the centre of the meat product. BaP mainly accumulated in the smoked casing, being four times in excess of the legal limit. This paper analyses the mechanism for preventing PAHs contamination during the process of smoking meat products.     

Occurrence of 15 + 1 EU priority polycyclic aromatic hydrocarbons (PAH) in various types of tea (Camellia sinensis) and herbal infusions

For the analysis of 15 + 1 EU priority PAH in tea and herbal infusions, an online-SPE-LVI-GC-MS method was developed. This method includes sample extraction of the tea and herbal infusions with saponification followed by an automated SPE clean-up step. For brews a liquid–liquid extraction with cyclohexane was performed before an automated SPE clean-up. Gas chromatographic separation was done using an Agilent J&W Select PAH (15 m × 0.15 mm × 0.10 µm) column, which allows the separation of the three benzofluoranthenes as well as triphenylene from chrysene. Method performance criteria such as method linearity, limit of quantitation (LOQ) and repeatability were determined and demonstrated that the method was fit for purpose. The method was used to analyse 15 + 1 EU priority PAH in 91 tea and herbal infusion samples. The levels of PAHs ranged from below 0.5 (LOQ) to 460 µg kg^?1, with a median of 4.7 µg kg^?1 and a mean of 39 µg kg^?1 for BaP, and from below 1.0 (LOQ) to 2700 µg kg^?1, with a median of 39 µg kg^?1 and a mean of 250 µg kg^?1 for total PAH, which were in good agreement with other studies reported in the literature. For the brews prepared under normal house preparation (20 g material in 2 L boiling tap water for 10 min), no total 15 + 1 PAH could be detected above the LOQ. With an extended brewing time of 30 min, a transfer rate between 0.25% and 0.52% could be determined, which results in no exceeding of the maximum limits given by the European Union directive for drinking water (EU Council Directive 98/83/EC).     

Benzo[a]pyrene and total polycyclic aromatic hydrocarbons (PAHs) levels in vegetable oils and fats do not reflect the occurrence of the eight genotoxic PAHs

Concentrations of polycyclic aromatic hydrocarbons (PAHs) were determined in 115 samples of olive oil (extra virgin olive oil, virgin olive oil, olive oil, pomace olive oil and blended olive oil), cooking oil (corn oil, sunflower oil, sesame oil, palm olein oil, soya oil, canola oil, mustard oil, peanut oil and mixed vegetable oil) and fat (butter and table margarine) collected from retail stores in Kuwait. Carcinogenic benzo[a]pyrene (BaP) was detected in 43% of the samples analyzed. Benz[a]anthracene and chrysene were detected in 37 and 45% of the samples, respectively, that did not contain BaP. Of the individual non-carcinogenic PAHs, naphthalene showed the highest mean concentration (14 µg kg^?1), while for the carcinogenic PAHs, BaP (0.92 µg kg^?1) and chrysene (0.87 µg kg^?1) showed the highest mean values. Approximately 20% of the samples within the olive oil and cooking oil sub-categories exceeded the EU maximum tolerable limit for BaP, with the highest level of 6.77 and 11.1 µg kg^?1, respectively. For the fat sub-category, 9% of the samples exceeded the tolerance limit, with the highest level of 3.67 µg kg^?1. The Kuwaiti general population's dietary exposure to the genotoxic PAHs (PAH8: benz[a]anthracene, chrysene, benzo[b]fluoranthene, benzo[k]fluoranthene, benzo[a]pyrene, indeno[1,2,3-cd]pyrene, dibenz[a,h]anthracene and benzo[ghi]perylene) was estimated to be 196 ng day^?1 (3.3 ng kg^?1 bw day^?1, assuming an average adult body weight of 60 kg). Results indicated that PAH8 and BaP_eq (total sum benzo[a]pyrene equivalents) are more reliable measures of the concentrations of other carcinogenic PAHs in oil and fat samples, while BaP and PAHs alone are not good indicators of the occurrence or degree of contamination by carcinogenic PAHs in these food products.     

Determination of benzo[α]pyrene in edible oil using tetraoxocalix[2]arene[2]triazine bonded silica SPE sorbent

Benzo[α]pyrene (BaP) is a well-known carcinogen in edible oil. In this study, a method combined solid-phase extraction (SPE) with fluorescent detection was developed using tetraoxocalix[2]arene[2]triazine sorbent (SiO₂-OCA) for the clean-up and enrichment of BaP. The interaction between SiO₂-OCA and BaP involves a donor–acceptor complex mechanism. The experimental procedure was as follows: BaP was extracted from edible oil with DMF/H₂O (9:1, v/v). Then, the ratio of DMF/H₂O was adjusted to 1:2 prior to SPE. The final concentrate was analysed using a fluorescence detector at excitation and emission wavelengths of 255 and 420 nm. The method was fully validated. The linearity was in the range of 0.1–100 μg kg^?1 with a coefficient of 0.999. The limits of detection and quantification were 0.03 and 0.1 μg kg^?1, respectively. The average recoveries were in the range of 88.0 ? 122.3%. The intraday and interday precisions were 6.8% and 9.2%, respectively. Compared with other methods, the method reported in this article shows a good detection limit, high reproducibility and recovery and linearity over a broad concentration range. This established method was also applied to evaluate real samples. The concentration of six tested samples was below 5 μg kg^?1.     

Assessment of the dietary habits and polycyclic aromatic hydrocarbon exposure in primary school children

Thirty Italian children, 7–9 year aged, living in Naples were investigated on their dietary habits and on polycyclic aromatic hydrocarbon (PAH) exposure by a food diary-questionnaire and one week duplicate diet sample analyses. Daily total food consumption mean value was 632 ± 215 g day^?1, median value 613 g day^?1. The daily energy intake and the diet composition meanly agreed with the official guidelines for the Italian children. Sixteen PAHs were simultaneously detected and, according to the European Food Safety Authority (EFSA) approach, benzo[a]pyrene; benzo[a]pyrene + chrysene (PAH2); PAH2 + benz[a]anthracene + benzo[b]fluoranthene (PAH4); PAH4 + benzo[k]fluoranthene + benzo[ghi]perylene + dibenz[a, h]anthracene + indeno[1,2,3-cd]pyrene (PAH8) were considered in evaluating the children's dietary exposure to PAHs. The benzo[a]pyrene (BaP) median concentrations in foods varied from 0.06 to 0.33 µg kg^?1. Only three samples of cooked foods (one fish and two meat samples) exceeded legal limits fixed by the European Union for BaP. Daily median intakes of benzo[a]pyrene, PAH2, PAH4, and PAH8 were 153; 318; 990; 1776 ng day^?1; their median exposure values were 5; 10; 28; 54 ng kg^?1 bw day^?1. The Margins of Exposure (MOEs) in median consumers agreed with the EFSA safety values except for PAH8.     

Co-occurrence of aflatoxins,ochratoxin A and citrinin in “egusi” melon (Colocynthis citrullus L.) seeds consumed in Ireland and the United Kingdom

The natural co-occurrence of aflatoxins (AFs), ochratoxin A (OTA) and citrinin (CIT) in melon seed samples obtained from retailers and households in Ireland and the United Kingdom (UK) was evaluated. AFs and OTA were determined by HPLC with fluorescence detection while CIT was analysed by HPLC-MS/MS. AFB₁ was detected in all (100%) samples (mean = 9.7 μg kg^?1; range = 0.2–66.5 μg kg^?1). Mean total AFs was 12.0 μg kg^?1 (range = 0.3–82 μg kg^?1). Commercially retailed samples showed a significantly higher AFB₁ contamination (p < 0.05) than the household samples. OTA occurred in 3 (13.6%) samples, while 4 (18.2%) were contaminated with CIT at very low levels. In this study, 68% of the melon seed samples were contaminated above the 2 μg kg^?1 EU limit for AFB₁ in oilseeds. These results highlight the need for the development of strategies to reduce AF contamination in “egusi” for human consumption.     

Relationship between total polar components and polycyclic aromatic hydrocarbons in fried edible oil

ABSTRACT

Deep-fried dough sticks (a Chinese traditional breakfast) were fried individually in peanut, sunflower, rapeseed, rice bran, soybean and palm oil without any time lag for 32 h (64 batches fried, each for 30 min) and fried oil samples were obtained every 2 h. The frying-induced changes in the levels of total polar compounds (TPC) and polycyclic aromatic hydrocarbons (PAHs) were investigated by edible oil polar compounds (EOPC) fast separation chromatographic system and gas chromatography-mass spectrometry (GC-MS), respectively. The correlations were analysed of TPC with benzo[a]pyrene (BaP), TPC and PAH4 (benzo[a]anthracene, chrysene, benzo[b]fluoranthene and benzo[a]pyrene) as well as TPC with PAH16 (USEPA 16 PAHs). The results revealed that the levels of TPC and PAHs in fried oil considerably increased with frying time, and the type of oil affected their formation, which could inform the choice of oil for frying. The total BaP equivalents (∑BaPeq) concentrations in fresh oil and in oil whose TPC exceeded 27% were 2.14–13.48 and 5.78–10.80 μg kg^–1, respectively, which means that the carcinogenic potency of frying oil was more pronounced than that of fresh oil. In addition, the TPC concentration was significantly correlated with the concentrations of the sum of the 16 PAHs, PAH4 and BaP, so that the levels of PAHs could be predicted according to the levels of TPC in fried oil. In European standards, the rejection point for TPC in frying oil should be recalculated when considered PAHs. In all, the concentration of PAHs is a vital factor for ensuring the safety of frying oil.     

Polycyclic aromatic hydrocarbons (PAH) in chocolate on the German market

Benzo[a]anthracene (BaA), chrysene (CHR), cyclopenta[c,d]pyrene (CPP), 5-methylchrysene (5MC), benzo[b]fluoranthene (BbF), benzo[k]fluoranthene (BkF), benzo[j]fluGoranthene (BjF), benzo[a]pyrene (BaP), dibenzo[a,h]anthracene (DhA), indeno[1,2,3-cd]pyrene (IcP), benzo[g,h,i]perylene (BgP), dibenzo[a,l]pyrene (DlP), dibenzo[a,e]pyrene (DeP), dibenzo[a,i]pyrene (DiP) and dibenzo[a,h]pyrene (DhP), the 15 SCFPAH, assessed to be relevant as well as benzo[c]fluorene (BcL) recommended by the European Food Safety Authority (EFSA), were analysed in different types of chocolate. The sample preparation included accelerated solvent extraction (ASE), size exclusion chromatography (SEC) and solid phase chromatography using small silica gel columns. The individual PAH were separated by gas chromatography using a VF-17ms GC column and detected by high resolution mass spectrometry (HRMS). The investigation of 40 samples of various types of chocolate with different cocoa contents resulted in a median benzo[a]pyrene (BaP) content of 0.22 μg/kg. Furthermore, the results showed a linear correlation between the content of BaP and the sum content of the 16 priority PAH. Therefore, the analysis of BaP as a leading substance seems to be suitable to estimate the PAH contamination in chocolate.     

Polycyclic aromatic hydrocarbons (PAH) in chocolate on the German market

Benzo[a]anthracene (BaA), chrysene (CHR), cyclopenta[c,d]pyrene (CPP), 5-methylchrysene (5MC), benzo[b]fluoranthene (BbF), benzo[k]fluoranthene (BkF), benzo[j]fluGoranthene (BjF), benzo[a]pyrene (BaP), dibenzo[a,h]anthracene (DhA), indeno[1,2,3-cd]pyrene (IcP), benzo[g,h,i]perylene (BgP), dibenzo[a,l]pyrene (DlP), dibenzo[a,e]pyrene (DeP), dibenzo[a,i]pyrene (DiP) and dibenzo[a,h]pyrene (DhP), the 15 SCFPAH, assessed to be relevant as well as benzo[c]fluorene (BcL) recommended by the European Food Safety Authority (EFSA), were analysed in different types of chocolate. The sample preparation included accelerated solvent extraction (ASE), size exclusion chromatography (SEC) and solid phase chromatography using small silica gel columns. The individual PAH were separated by gas chromatography using a VF-17ms GC column and detected by high resolution mass spectrometry (HRMS). The investigation of 40 samples of various types of chocolate with different cocoa contents resulted in a median benzo[a]pyrene (BaP) content of 0.22 μg/kg. Furthermore, the results showed a linear correlation between the content of BaP and the sum content of the 16 priority PAH. Therefore, the analysis of BaP as a leading substance seems to be suitable to estimate the PAH contamination in chocolate.

---

Zusammenfassung:  Für Bestimmung der 15+1 von der EU als priorit?r eingestuften PAK in verschiedenen Schokoladen wurde eine Analysenmethode bestehend aus beschleunigter L?sungsmittelextraktion (ASE), Gelpermeationschromatographie (GPC) und Nachreinigung an einer Minikieselgels?ule verwendet. Die Identifizierung und Quantifizierung der einzelnen Verbindungen erfolgte nach gaschromatographischer Trennung mit dem hochaufl?senden Massenspektrometer unter Verwendung einer VF-17ms GC-S?ule. Die Untersuchung von 40 Schokoladenproben mit verschiedenen Kakaogehalten erbrachte im Median einen Gehalt an Benzo[a]pyren (BaP) von 0,22 μg/kg. Es zeigte sich weiterhin eine enge Korrelation des BaP-Gehalts vom Gesamtgehalt der 15+1 EU-PAK. über die Leitsubstanz BAP l?sst sich somit der Gesamtgehalt der 15+1 EU-PAK durch die alleinige Bestimmung von BaP in Schokolade absch?tzen.

---

Received: February 10, 2009; accepted: February 25, 2009.     

Development and application of a non-targeted extraction method for the analysis of migrating compounds from plastic baby bottles by GC-MS

In 2011, the European Union prohibited the production of polycarbonate (PC) baby bottles due to the toxic effects of the PC monomer bisphenol-A. Therefore, baby bottles made of alternative materials, e.g. polypropylene (PP) or polyethersulphone (PES), are currently marketed. The principal aim of the study was the identification of major compounds migrating from baby bottles using a liquid–liquid extraction followed by GC/MS analysis. A 50% EtOH in water solution was selected as a simulant for milk. After sterilisation of the bottle, three migration experiments were performed during 2 h at 70°C. A non-targeted liquid–liquid extraction with ethyl acetate–n-hexane (1:1) was performed on the simulant samples. Identification of migrants from 24 baby bottles was done using commercially available WILEY and NIST mass spectra libraries. Differences in the migrating compounds and their intensities were observed between the different types of plastics, but also between the same polymer from a different producer. Differences in the migration patterns were perceived as well between the sterilisation and the migrations and within the different migrations. Silicone, Tritan? and PP exhibited a wide variety of migrating compounds, whereas PES and polyamide (PA) showed a lower amount of migrants, though sometimes in relatively large concentrations (azacyclotridecan-2-one up to 250 µg kg^?1). Alkanes (especially in PP bottles), phthalates (dibutylphthalate in one PP bottle (±40 µg kg^?1) and one silicone bottle (±25 µg kg^?1); diisobutylphthalate in one PP (±10 µg kg^?1), silicone (up to ±80 µg kg^?1); and Tritan? bottle (±30 µg kg^?1)), antioxidants (Irgafos 168, degradation products of Irganox 1010 and Irganox 1076), etc. were detected for PP, silicone and Tritan? bottles. Although the concentrations were relatively low, some compounds not authorised by European Union Regulation No. 10/2011, such as 2,4-di-tert-butylphenol (10–100 µg kg^?1) or 2-butoxyethyl acetate (about 300 µg kg^?1) were detected. Migrating chemicals were identified as confirmed (using a standard) or as tentative (further confirmation required).